USB port can not detect my new camera

Similar Questions

• Since the L7680 installation my usb ports are not detected...

  It seems that something in the registry has been changed.  My Western Digital Passport (mass storage device) is not detected is not my SanDisk Micro (2G).  Western Digital will work in the USB from the printer, but don't the SanDisk.  I've lost the use of all of my USB ports on my computer processor and montor.  They used to work before installation.  I uninstalled and reinstalled, I check startup items in MSCONFIG.

  I read on the Microsoft support page which the hkey_local_machine\system\currentControlSet\Control...

  should be set to activate, but I do not have this folder in XP.

  Western Digital does not know what is happening, or not SanDisk.  HP really gave me the run around way to uninstall and reinstall, but I didn't get an answer that solves the problem.

  It seems to me that since it was drivers from HP which caused my other unit to pass unnoticed, HP should be able to tell me how to solve this problem.  I do too much research for a new product.  I know I'm very frustrated, and since this is a new printer I still have time to take it for something that's going to work.  I had a Dell that has worked well, I wanted to just an upgrade.  I guess I could have updated by Dell.

  Just about the evacuation, someone has an idea what the fix is for my USB not detected ports that have been replaced by the reader on this printer?

  I added a new HP printer to my set all my ports no longer works. None of my flash drives or removable hard disks worked. I tried everything and then read "ports must be updated". My computer is older than three years and the ports of origin are 1.1 and are of most new USB 2.0 devices. Long story short, I went to microcenter and bought new ports ($11.00) and add them to my computer. All ports are now functional.

• USB ports do not detection devices

  Hello

  My USB ports are sensors not when I their connection. I hear the noise, which indicates a device has been connected, but when my laptop is trying to install the driver, it gives me an error Code 39.

  I see an icon in Device Manager yellow triangle-shaped when a device has been plugged in. I tried to uninstall and reinstall my driver and running fixit (said mass storage device USB has a driver problem and can't fix), but no luck.

  I'm running Windows 7 Home Basic Edition and tried to insert a USB Hard Seagate Drive, Kingston and a Sandisk USB key (they all work fine on other computers).

  Help, please!

  Hello Marilou,

  Thank you for your response.

  What is the brand and model of your laptop?

  I appreciate your efforts to resolve the issue.

  I also appreciate the fact that you ran Microsoft fixit.

  However, due to USB devices, I suggest you to try the following methods and check if it helps.

  Method 1:
  Uninstall and reinstall the USB controllers and check. Please follow these steps:

  a. press Windows + R keys, type devmgmt.msc in the run window and press ENTER.
  (b) in Device Manager, expand 'USB Bus controllers'.
  c. a device under "In Bus USB controllers" right click and click on Uninstall.
  d. perform the same step for other devices. Once completed, restart the computer.

  All USB controllers will reinstall automatically.

  If this does not help, use method 2.

  Method 2:
  Turn off the "selective suspend" feature of the USB hub driver and check the issue. Please follow these steps:

  a. press Windows + R keys, type regedit into the run window and press ENTER.
  b. look for, and then click the following key in the registry:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB

  (c) in the "Edit" menu, point to 'New' and then click 'DWORD'.
  d. Type "DisableSelectiveSuspend" and press ENTER.
  e. in the "Edit" menu, click on 'change'.
  f. type '1', and then click ok.

  Note: This setting affects all USB host controller drivers in the system.

  For Windows update number, I suggest you try using the steps described in this article and check.
  Reference:
  Error 0 x 80070005 in Windows Update when you try to install updates
  http://Support2.Microsoft.com/kb/968003

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry

  The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this information helps.

  Thank you

• SanDisk Cruzer Blade USB key can not detect properly by Win 7 64 bit

  Hi all:

  I have this problem on and outside.

  This time, it's ok and next time can be bad that the USB device is unable to detect Win 7 64 bit. It's OK to Win Xp all the time.

  I have referred to as the previous posts for this problem and remove the VID_0781 by REG_EDIT, also try to uninstall the device from the hardware in the computer and re - install the device. I also did the replacement of usbstor.inf in c:\windows\inf to another subfolder.

  from c:\windows\.

  The result is intermittent it's Ok this time and not okay at other times. It's really wasting a lot of time to try this or that, and the result is intermittent.

  Can anyone or Sandisk people leave a good and permanent solution to this problem?

  Thank you and best regards,

  tangsuan

  Hi all:

  I want to update this solution for this problem of Sandisk support.

  This solution may be different from one case to another, but if you have installed Samsung KIES in PC, then most likely it is the solution.

  If you kill the KiesTrayAgent.exe, the Sandisk can be detected smoothly whenever you plug it into my laptop.

  Thanks and respect of the best.

• Satellite M30-604: USB Port can not find the driver

  Hello

  I keep having the same problem on my Satellite M30 604 when connecting to a USB device.
  It does not really matter with this kind of device, the problem still.

  Whenever I have insert the USB plug into one of the slots, my home XP keeps popping up the wizzard software.
  Even with devices without drivers such as USB keys, it keeps bothering me and finally tells me that it cannot find the right driver.

  If I try to install a printer, it installs the software found, but finally stops the operation because it can't find the driver (?). I don't know in what direction I should look at to solve this.

  So if anyone can help me on this, I would be very grateful!
  Edwin

  Hello, Edwin

  It's very strange because it is not necessary to install a USB driver and standard Microsoft USB driver should work well. I put t know if this can help, but please check this page

  This fix is also part of the factory settings (recovery image on the delivered CD). By the way: your device is about three years old and it will be interesting to know since when you have this problem. Just for example: I have more Satellite 1900 with USB 1.0 and use USB keys and drive external HARD without any problem.

• USB port does not detect the USB storage

  Hello

  My company gave me a Lenovo ThinkPad L420 and whenever I connect the USB external storage, I am not able to see it on my computer but I can see the unit on Control Panel devices and printers. Please let me know how activate or activate?

  Thank you

  Sayed Toufiq.

  You can google for it!

  http://pcsupport.about.com/od/Windows7/HT/change-drive-letters-Windows-7.htm

• Computer can not detect any sound cards and graphics or communication ports.

  Recently I reinstalled Windows using the CD, I had Dell, when I bought my computer. However, when I was done with the installation, I went on youtube to look at things and I realized that the sound was not working. I thought I must have forgotten to install the driver for my sound card, then when I tried to install, it says something in the sense of "error". - Impossible to find Port Com1 I looked into this a bit on google and found that it is probably disabled in my BiOS. I'm not sure what to do after that, but I hope that someone knows why my computer can not detect anything.  hate viruses

  http://support.Dell.com/support/downloads/index.aspx

  Go to Dell website > drivers and downloads Section > key in your model number > get latest XP drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• My USB ports do not work.

  Hello
  Yesterday, I bought a brand new printer, implemented, it was working fine, and then it just stopped. So I fought a bit with her, decided the printer was defective and would resume and put it out to a new, and meanwhile put my printing task on my jump drive and bring it to our local printing store. However, when I put my jumpdrive into the USB port to transfer the project, my computer would not my USB - stick. So now, I think that for some reason that my USB ports are not working. Why is this happening and how to fix it?

  Hello

  1 reboot to be sure nothing blocks the ports.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel - Device Manager - click in the box of white/white - VIEW - show hidden devices

  Look everywhere EXCEPT USB controllers for your device and if find you them (maybe
  plus_d' one of each) under disk drives, you can have several - right CLICK and UNINSTALL
  for all instances

  Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
  UNINSTALL all but the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Removed USB controllers: can not return - "this device cannot find enough free resources that it can use. (Code 12)

  Original title: removed USB controllers: can not return

  Hello

  So today I tried to connect to a printer, and it wouldn't work (separate the issue, I don't want to worry about that now)

  I've seen several messages saying: you need to uninstall the USB controllers in Device Manager and then restart your PC. The pilots would then automatically reinstalled.

  It didn't happen, and now my Dell touch screen does not work. I can miss several other USB controllers too, I uninstalled about 3 of them, but I don't know whether or not it has been reinstalled.

  I currently have:

  -Hub USB generic

  -Enhanced host controller USB Intel (R) 8 series #1-9C 26

  -USB root hub

  -Host controller compatible xHCI USB

  Note that the last of them was a symbol of error on it and reads as follows:

  "This device cannot find enough free resources that it can use. (Code 12)

  If you want to use this device, you will need to disable one of the other devices on this system. »

  Can someone please tell me how much USB controllers I should have and how to save them?

  Thank you very much

  Hi Shalini.

  Thanks for the reply, but if you read through the posts on this thread, I think you will find that it has already been suggested that I do these two things - what I've done many times without result.

  Fortunately, I managed to fix it myself.

  To satisfy your curiosity and help someone else who could see this thread with a similar problem, here are the steps I took finally solve the problem:

  ______________________________________________

  I was always convinced that the problem is basically with the xHCI USB controller that I saw always reported as not working not properly in the device (Code 12) Manager. With this in mind, I set out to see if I could determine what the device was supposed to be in conflict with. I ran msinfo32 and began to examine the conflicts/sharing section. After a while, I decided I could not see anything obviously problematic or direct me to the controller xHCI, so I gave up on that front.

  Well, if I couldn't fix the problem with the current installation, maybe that I could find another way to install the xHCI USB controller that could circumvent the flaw that seems to be caused when windows reinstalls automatically it when restarting after the abduction. So I started trying to learn more about this "xHCI USB controller" - since Googling this term has given no end of problems not related.

  In Device Manager, I found a way to isolate the details of this driver in device (somewhere under the properties I believe) Manager. This has created a custom device showing in view only a select few connects the Manager. I have spent some time in the analysis of these and found the time during which the camera has stopped working properly. Suddenly a pattern emerges. Over and over again, see you the following series of when I was hoping that allowing windows to reinstall automatically the driver would to fix:
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been removed

  [Rebooted PC]

  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been configured
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 had a problem starting.

  Under each newspaper was referring to a driver name, I didn't already had access to: driver name: usbxhci.inf

  Now I got some new information about the xHCI USB controller, I took to Google. After much research (and not find something relevant), I found 2 obscure references to the driver who seemed at least somewhat relevant.
  The first reference has been a post on the forum where someone's USB ports stopped working. very similar problem to mine! There is little of any particular use in the nets, with the exception of the reference to a couple of windows updates: KB 2823516 or KB2822241

  It is not clear exactly what usbxhci.inf capacity was tied to these updates, but I made a note of them and moved.

  Another article contained no mention of specific ports USB not working does not and was centered around a different problem entirely. However, he has mentioned an another windows update: KB2919355-x 64.msu

  This one (as I remember) was clearer on the relationship between the update and changes to the usbxhci.inf file.

  Now, I had three updates which could make changes to usbxhci.inf at one point. With their name on a piece of paper, I started looking through my updates installed to see which ones I had installed. I soon discovered that Ko 2823516 or KB2822241 were not present on my PC, which saved the penalty to guess who would be the right to uninstall first.

  KB2919355 has been installed, and I made the decision to uninstall it, because as far as I knew, this update changed something in usbxhci.inf. After the initial uninstall was completed, but before the mandatory reboot for changes to take effect, I went into Device Manager and removed the xHCI USB... because I was afraid that if the new, "defective" was always present during the reinstallation of the update, it doesn't change anything.

  The device is removed once more, I rebooted the system. He drives for a considerable period, uninstall the update and then seems to have some sort of hitch; declare something in the sense of "we could not complete the operation. Changes to undo. " He stayed like that for a while before the system became operational again and began to "prepare windows. Once it was over, I discovered that my touchscreen and USB ports worked very well.

  Investigation later showed that the compatible USB xHCI host controller was is no longer marked with warnings. In addition, a series of USB controllers appeared that had not been there when the xHCI device was defective. I was also pleased to note that the update of windows for KB2919355 had already been reinstalled without messing up anything.

  _________________________________________________

• HP 15-r002se: USB port does not

  I have a problem with my laptop [HP 15-r002se] all three 3 usb ports do not work, or even detect that something is plugged, I tried techniques to conquer the problem by the system of formatting and reinstalling windows 8 32-bit where I found myself without success, because I can't able to get compatible drivers of troubleshooting. Then I go to the usb ports even on windows 7 64 bit does not. and finally, format and install windows 10 64-bit, I downloaded the drivers from hp website, but unfortunately when I run the downloaded software sometimes nothing appears either to the pop-up a message on the error or continuation and sometimes it shows this kind of error after it finished extracting

  

  Finally with the help of pilots pack that I managed to install all required drivers but finally arrived with NO SUCCESS, yet neither the operation of the usb port. Here is the screenshot of my device manager.

  

  Please, I seriously need your help to solve this problem, because I am a student, I can afford to buy another laptop earlier

  Hi @Mustapha_Musa,

  I read your message and please try the following steps. A brilliant work has been done by trying these steps. Kudos to you on this point. It's a problem of clear material with the device. The USB ports are defective, the motherboard should be replaced. you will need to contact HP telephone support on this subject for the machine.

  HP technical support are available by clicking on the following link:
  
  http://h22207.www2.HP.com/us-en/?openCLC=true
  
  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.
  
  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.
  
  (3) Once finished, click the "Show Options" at the bottom right.
  
  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

  The workaround, for now, is the following: If you have a USB port on the device that works, then you could buy a USB port extender and connect it to the port good work.

  Then you connect other devices to the USB port extender. This way multiple devices may still be connected to the computer.

  Just to say thank youPlease click the ' Thumbs Up 'button to appreciate my efforts. If it helps, Please mark this "accepted Solution".

  Thank you and have a great week ahead.

• Pavilion S5-1204: USB Ports does not: Windows 7 HP Pavilion Slimline

  Hi all

  Yesterday all of a sudden the USB ports are not read.  I have cameras and use a data transfer cable or a card reader to transfer to the office.  Now they do not read.  Tried the front and back of the usb ports.   However, the optical mouse that uses a usb device works.   I don't understand how the mouse works and the purse strings of data transfer and the readers aren't.

  Win 7 64 bit

  HP Pavilion Slimline desktop computer

  Help!

  Update: I did troubleshoot a HP check and update driver.  The screen messages

  USB root hub: this device does not work correctly.

  The current tab:

  Generic USB Hub (6)

  1 port available

  Power required: 0mA

  Solved.

  I've narrowed the problem to the camera. Very strange. The camera will take pictures and display them on the screen. But something is happening internally where the image will not transmit or transfer it via a usb device.

  I have another device with a transfer device and it works. So it seems I have to buy a new digital camera. BTW, it is a Nikon S2800 - not recommended.

• Photosmart C4280 All In One: USB Port does not work

  When I try to scan, I get a message saying that the USB port is not installed. It is installed, but I bought a new USB port and still get the same message.

  Hi @MrsQ3,

  Thanks for getting back to me with this information.

  Have you already tried to install the software and drivers from hp.com printer? If you do not try to download the HP printer installation wizard for installation. This tool will find the most recent version of the printer software and drivers available for Windows 10.

  If you have already installed the printer software, try downloading and does not perform the HP print and Scan Doctor. This tool can diagnose and solve many problems of printing software and printer.

  Please let me know how it goes.

  Thank you.

• Vista - usb ports are not recognized unknown device

  Vista - usb ports are not recognized unknown device. any usb device it appears unknown. all worked a few days hardly, but after that I connected my Kodak camera - which does not, now, nothing works. Any help would be appreciated.

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  Follow the instructions below that may help you resolve the issue.

  Method 1:

  Try to connect USB devices to a different USB port and check if you are able to access.

  Method 2:

  Click on the link below to run Fix it which will help you to solve the problem.

  Tips for solving problems of USB devices

  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx

  Click on the link below and install the update.

  Rollup cumulative update for USB in Windows Vista Basic components

  http://support.Microsoft.com/kb/941600

  Try to connect the camcorder to the other USB port and on the other computer and see if the problem is resolved.

  Method 3:

  Let us try to disable the Antivirus security software and check the number.

  Re-enable the security software after checking the issue.

  You can also try disabling the firewall and check the issue.

  Re-enable the firewall after checking the issue.

  Method 4:

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure.

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot

  Step 2: Enable half the services

  Step 3: Determine whether the problem returns

  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns

  Step 6: Resolve the problem

  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista

  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to the Normal mode.

  Uninstall or update the program that is causing the problem.

  Check whether the problem is resolved.

  You can also check out the link below.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/6be4581d-8fbd-407F-815E-b475c35ca586

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• EliteDesk 800 G1 USDT: usb ports do not provide enough power

  We have a scanner usb requiring 500mA of power.  However, for many of our clients using HPs, the usb ports do not provide enough power to the scanner causing the application to crash.  Some customers use the HP EliteDesk 800 G1 USDT, others use HP zero client t310.  Connect the scanner to a usb hub powered solves the problem every time.

  Y at - it changes, they can do for the Bus USB controllers to ensure that a particular port will be able to provide 500mA so they did not need to buy a usb powered a system hub?  Or do you have another suggestion?

  Thanks in advance.

  I'm not familiar witht eh models accurate but 500MA is the output for USB 2.0 max but 3.0 can go higher have you tried usingn 3.0 ports if not you can also get a cable Hat uses the power of 2 ports.  Many systems have problems with the only Scanners USB and power supply.

• NB200-12N - USB port does not work

  Hello

  I updgrade my OS from windows 7 starter edition to now a windows 7 home basic 32-bit usb port does not work is the (only) in the left near card reader sd and lan.
  Can you please hellp me to install it? I have download the drivers from Toshiba for my NB200
  But does not work.

  Thank you

  Paulo

  If everything is OK and right drivers all USB ports should work. You cannot install the drivers for each port separately and force one of them to work properly. On this machine, all three ports are the same USB2.0 ports.

  Try reinstalling the chipset utility.

  By the way: two other ports work well, right?