Everything on my computer is larger print after I hooked to give a presentation in power point.

Similar Questions

• Help! Computer connection issues / printer after Windows 7 upgrade

  I HOPE THAT SOMEONE HERE CAN HELP ME!  I am frustrated beyond belief.

  I have upgraded from Vista to Windows 7.  My computer is a hp dv5 pc, 64-bit.  My wireless printer is a hp OfficeJet J4680c.  Before the upgrade, wireless printing was perfect.

  Since the upgrade, when I try to print, two things will happen:

  (1) when I try to print, there is a mistake that the document cannot print.

  OR

  (2) when I try to print, the printer icon appears that the document will print, but nothing happens.  When I right click and open the Active printer, it shows that it is "printing", however the number of pages displayed is n/a.  After 2-3 minutes, the document simply disappears from the print screen, as if it printed.

  I went through the troubleshooting steps on my hp PC help & support, I have read the forums for hours and tried various fixes, I went through the center of solutions hp printer troubleshooting steps...

  The final diagnosis is that the computer is unable to 'find' the printer. Here is some additional information:

  I was able to print occasionally during the troubleshooting process (see below for more information)

  All the drivers are up to date.

  Computer and the printer are connected to the same network wireless in my house.

  Whenever I have manually print the "HP Network Configuration Page," it shows that the printer is "ready".

  Windows defender is OFF

  The Windows Firewall is DISABLED

  3rd party firewall Vipre has been RUNNING, with the same results to be

  What follows can offer anyone a clue as to the problem:

  Four times during this process of troubleshooting, I completely uninstalled printer and then reinstalled using the updated driver and instructions on the hp Web site.

  Whenever during the installation process, the computer does not find the printer, and I have to manually enter the IP address of the printer.  Then, the computer does not find the printer, and the installation continues.  Until he comes to the end, when it is completed at 98%. Then, I get a message:

  "Rediscovery printer detected problems. Maybe your PC is not able to track changes in the online status of your printer. If you use firewall software, make sure the port UDP 427 is unblocked from your printer at 192.168.0.5 for your PC. To resolve the problem, try to feed your printer market. »

  (of course checked summer port and the printer power is turned and the...) I followed all steps completely).

  Then, I give myself a choice or continue installing the software without connecting to the printer, or to continue with the installation of the printer.

  When I tried the first choice, install the software without the printer, then I went back later to install the printer. During the installation of the printer, I'm at the same point at 98%, with the same message.

  I also tried to install the printer in any case and it ends up all right, and then the printer worked for a day or two. But after a day or two, I'll be once more cannot print, and I will either receive the error message, otherwise it is not only print (SEE the BEGINNING OF THIS POST).

  I've tried everything I know to do and no message forum or troubleshooting is now offering me any new information.

  Can you help me???

  Have you tried the 'updates' on this page?  There is a couple who look like they would help.

• After that a game downloaded, everything on my computer became a great size. How to get back to normal

  After that a game downloaded, everything on my computer became a great size. How to get back to normal

  After that a game downloaded, everything on my computer became a great size. How to get back to normal

  Put the screen resolution
  http://www.Vistax64.com/tutorials/84291-screen-resolution.html

  Re-set DPI scale

  http://www.Vistax64.com/tutorials/84233-DPI-scaling.html

• Printer does not print after canceling a print job even if I deleted the queue and stop the printer and the computer.

  Re Vista - printer does not print after canceling a print job even if I deleted the queue and stop the computer and the printer and restarted.

  Hello

  ·                         try to uninstall and reinstall and use the latest printer drivers VISTA for your model of the manufacturer of the printer

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the information of the links to the other

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• W7 professional after remote access to my desktop computer 'loses' his printer. Windows / devices and printers / "Officejet 6000.

  W7 Professional (both sides) after remoting in through our company intranet, my desktop computer 'loses' his printer.  If I go to "windows key" / devices and printers / she sees a "Officejet 6000', which is connected via usb, windows, but there as"not specified ".

  Hello

  Thank you for visiting the Microsoft answers community site. The question you posted would be better suited in the Technet forums. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  I hope this helps.

• laptop not having not the portable printer after that computer settings has been turned off

  I have a problem with my laptop and my printer after I connect to the WIFI printer. It will work if it was attached to the printer, but as soon as I turn it off the setting have disappeared. My laptop works on WP7 and canon mg5200 printer. can someone help me.

  Hi Phil,

  Have you installed new software or hardware before the show?

  It seems that printer drivers could be exceeded and must be repaired or updated. We will analyze and identify the cause of the problem.

  You can run the printer Troubleshooter and update the drivers of the material provided.

  Solve printer problems

  I could not locate the exact model number you have provided. If we're not the printer model number, you can choose one that fits in the list. If the printer model number is the same and that you did not find the driver, then we will have to install the driver of a similar model.

  You can see this article from Canon.

  If the problem persists, you may need to contact Canon support for more information.

  Hope this information helps. Response with status so that we can help you.

• OfficeJet 5745: Cannot print after update of Windows 10

  I've updated to Windows 10 and now have problems printing.  Help!  I've done all the troubleshooting, coil status stuff!  I'm used to be able to print from the internet, scanning to my computer or email and print wireless from my phone.  I now can not print anything!  I tried to install Windows updates.  Should what printer I configure default network or regular?  Use the printer pdf microsoft thing?  I am desperate... saved my bank statement online (pdf) to my documents and it would not print the Bank or my documents!  Before this I had problems after that my hard drive crashed and I got a new hard drive.   When my hard drive crashed I was using WINDOWS 10 and everything on the big printer worked; they sent back with new hard drive on windows 8.1 and I had I thought that the upgradew would solve the questions.   I could print and scan but no wireless for my phone on the new HDD in windows 8.1 and upgrade to 10 thought would solve my problems, but now it's worse... Help!

  Hi @savra,

  If your computer is connected to the printer on a wireless network, you do not want to send print jobs to the network printer.

  Here is a support document to help with printer after Windows 10 upgrade problems - after Windows 10 Upgrade, printer problems occur.

  Aside to make sure Windows updates are up to date, there are a few other updates that can help with printing.

  Microsoft has released an update that is supposed to help with wireless printing - Cumulative Update for Windows 10.

  There was also an update for Adobe Flash Player in Internet Explorer and Microsoft Edge who can help get this impression of your bank's site - Update for Adobe Flash Player.

  Please let me know how it goes.

  If this helps you find a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• Everything on my computer has been reduced.

  The other night my power went off while I was with my computer. After a few hours power is relit and I restarted my computer. Now everything on my computer has been reduced. I mean everything. All the texts, web pages, Itunes, Yahoo Messenger, all my desktop icons, all my photos, everything. All my settings are the same when the power has been turned off, I have not changed anything. How can I change this?

  Try these fixes:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not fix it:

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  Then:

  http://Windows.Microsoft.com/en-AU/Windows-Vista/change-screen-resolution

  Change the screen resolution

  Screen resolution refers to the clarity of the text and images on your screen. At higher resolutions, items appear sharper. They appear also smaller, so more items adapted to the screen. At lower resolutions, fewer items adapted to the screen, but they are larger and easier to see. At very low resolutions, however, images may have serrated edges.

  See you soon.

  Mick Murphy - Microsoft partner

• Plotter of selfs of large print files

  Sometimes in printing intensive Illustrator CS3 and CS4 files memory with photos for a large plotter HP, the files do not print. For not to stifle the plotter, is it possible to print the Illustrator file a little at the same time for the same piece of paper? The parties will all have to line up perfectly. I think remember that in older versions of Illustrator, there is a parameter called something like 'split long paths' what impression, or such a thing, but I cant find it in the print dialog box.

  If you have Acrobat and Distiller, I found Acrobat printing to be much faster at printing large files. I work with very large maps which were > 50 000 objects in them and I found print directly from Illustrator excruciatingly slow. I usually save a copy a profit per action (usually v.8) and distill the EPS to PDF and print from Acrobat. The reason why I save as an old version that EPS, it's time to save the file is very short. I tried to print the larger map I directly in Illustrator and stopped printing after an hour of queue. The same file, back-recorded in a Version 8 EPS, take ~ 45 seconds to record, 1 minute to distill and ~ 5 minutes for the coil and to start printing on our HPs. In this way, you can maintain the integrity of the placed images or embedded in your file HAVE original without having to adjust or re-rasterize images. You can also use Acrobat to refine your optimization without destroying your original files. It can also help you find out if you have a problem with a font, bad graphic style or bad faster than if you had to wait an hour for it to be rolled up, and then the printer will tell you, he had a postscript error.

  If your effects of rasterization of the Illustrator document are set to high and use one of the press to distill defining default values, you should be able to get good results and the fastest wait time possible. It is also beneficial because everything you have in a mask will be cropped (images) or deleted (paths that are not visible. This also flattens the transparency effects that you may have.

  It is my experience and has been a very reliable way for me to print anything I have, be it a size or tiled to make a 18'x 9' card. (One of my clients wanted to paper a wall with a highly detailed relief, the world satellite map.) Satellite image was 200 dpi to scale to 100% tile and it has started printing after about 15 minutes of waiting).

  Hope this helps,

  D.

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• DeskJet 1050 - J410a: HP Deskjet 1050 does not print after upgrade of Windows 10

  Dear forum,

  I recently upgraded my HP Windows OS 8.1 for Windows 10 desktop computer. My deskjet 1050 printer, which worked fine before the upgrade, does not properly more print after the upgrade.

  I used HP Print and Scan Doctor several times, indicating no any problems. I am able to scan documents, the question is limited to printing. I also deleted and reinstalled the drivers at least 2 times (and restarted all systems on a regular basis).

  • A "test print" works very well.
  • When I print a PDF from the edge, the printer creates output but not good quality.
  • When I print an office word document, pages came out empty.

  3 cases have a common behavior, whenever I get an error message. "Morning maken puts printer niet mogelijk. Duch is for "cannot connect to the printer.".

  Do you have any tips for me?

  With sincere friendships.

  Pieter

  HeyPieter_Belgium

  Welcome to the HP Forums, I'd love to help you with printing problems you encounter. Although I am not sure what is cause of the error of communication, or of poor quality, I suspect it has something to with the pilot and the recent upgrade. I suggest to uninstall the software, remove the Chuck from the properties of the server, and then put it back using the printer Installation Wizard. I will list the links and instructions below to help you in each of these steps.

  HP printers - uninstalling the software of the printer (Windows)

  Remove the driver from the print server properties:

  1. in the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8, 8.1 and 10 -select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If documents are stuck in the spooler to print, you see an error, cancel all documents waiting in the print queue or try restart the spooler to print, and then try to delete the driver from 'Print server properties' again. If she will not always remove the sachet, restart the computer and the printer should correct this error "in use" and allow the driver to be removed.

  • If him you continue to get an "in use" message followed the steps in the document here. The specified printer driver is currently in use

  Download and run the Installation Wizard for printer: www.HP.com/go/Tools 

  If this solves the problem, please indicate your post as solved by clicking on the accept button Solution below. If you need help, let me know!

  Thank you.

• DesignJet 5500: hurt large print PDF file

  I try to print a large PDF file to my 5500 and I'm getting "out of memory" and the error messages "lost data".  I tried to use the cable parallel and through the network interface.  I don't know how to check, but I guess that the printer has the amount of memory that was the standard when the printer was new.  Problems of memory seem to be linked to the memory of the printer, because the computer has a lot of memory.

  I have a RIP Fiery X 2 - CP, but I've never used. Do I have to use some sort of RIP to the buffer or coil (whatever it's called) between the computer and the printer memory?

  I tried to print a picture 63 "long that is 30" wide, the printer will print the entire length but only approximately 12 "wide.

  Let me know if you have any questions.

  Hello

  You can find the firmware on the following link

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=82225 & swItemId = pl_59704_5 & swEnvOid = 228

  The 5500 doesn't have an EEROM reset like the T795.

  If you install the driver HPGL2, go to printing preferences > Services > troubleshooting Menu > compatibility with app 19 bits, use send as Bitmap.

  Issue.

  On what application the PDF has been created?

• OfficeJet 6210: Officejet 6210 do print after upgrade to 8.1 Windows

  I've reluctantly Windows 8 upgraded to 8.1.  And now, my Officejet 6210 not print.    When you are prompted to print, the printer icon appears in the toolbar showing employment is printing, or, a message appears indicating printing, but nothing prints. The printer is the default printer.  There is nothing in the queue.  I checked if the printer is paused or offline.   I ran "HP print and scan doctor" repeatedly indicates that everything is good and the printer works fine.  I've uninstalled and reinstalled the CD software.  I downloaded the driver from HP/support.   I stop and restart the printer spooler.  I disconnected the firewall.  I unplugged and pluged the 2 USB of the computer and the printer.  The computer and the printer was arrested over and over again.

  What else could be?

  Help!

  Hello! Welcome to the @matt_2 forums

  I read your post on printing problems, you've had since the upgrade to Windows 8.1.

  I checked some information and as you can see below, the Officejet 6210 is only supported by a Windows Update, which means that you can try to run all your Windows updates and try to print again. If the printer still doesn't print, you would look in an upgrade of the printer at this time. If you want to call us to see what are your options for the printer, I'll leave the details below.

  I hope this helps, have a great Monday

  source

  

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• Cannot print on a Brother printer after Windows Update

  We share the same brother MFC-8660DN on a network (Win XP x 4 & Win 2008 Server x 1), everything was fine until yesterday (16/09/10). 2 XP computers cannot print (Status: printing error) just after the recent update of windows installation (windows auto update has been set for each week). When we tried to print to the brother printer, he would be stuck in queue for a minute and a bubble pop up "document cannot be printed." 2 computers work fine otherwise. Everything works normoally and can be printed to another printer like Canon. (PS: I tried to uninstall and reinstall the brother printer driver, but no luck the question of setting)

  On the other hand, the other 2 XP did not have an update, and so they can't always print on the Brother printer. Also, Win 2008 server doing a windows update auto but print very well so.

  Therefore, I believe that the update of windows XP must have something to do with the printing error. Is there a fix or update? Alternatively, we can uninstall the recent windows update (only one?) to solve this problem? I'm not sophisticated OS, do not know what could be uninstalled. Help, please!

  I received a call from a client 2010-Sep-16 that they could no longer print
  on a network printer from any workstation.

  Workstations have Vista Business 32 and have been updated morning of September 16.

  The server is Server2003 & printing it still worked well.

  Printers using IP ports very well for more than 2 years.
  Fix was to use instead of the intellectual property & create ports with the full share name.
  
  The IP address of the printer had not changed AND
  I couldn't always navigate with IE8 (using IP address)
  printer see printer configuration data

  Workstations are Server 2003 domain

  This trick of name full-fledged was how I had to put in place
  Vista Home Premium workstations
  to use network printers in home networks.

  Why Vista Business "updated" settings for Home Premium?
  Is this a permanent 'update '?

  Why no matter what version of VISTA do this?
  Windows 7 has the same problem?

  With Vista Business 32 (short-term)? solution was to change the port to a local port with full sharing of the printer name

  See you soon

• Spoolsv.exe has 99% of the cpu when I turned off the printer after printing.

  Original title: spoolsv.

  I recently installed a new printer Lexmark Pro715.  Everything works fine, no problems with printing, but as soon as I put off the printer after printing, spoolsv.exe takes 99% CPU.  If I leave the printer in mode 'sleep', the problem is, but I do not often print, I prefer to turn off completely.  There is nothing in the print queue, everything else seems normal.  I can use the Task Manager to stop it, but this isn't a good solution in the long term.  I run MS Update and uninstalled and reinstalled the printer, with no effect.  It's driving me crazy.  I have Windows XP Home Edition SP3.

  From what I've read on the Internet about the print spooler using 99 to 100%, Norton is also sometimes involved as a contributing factor to a runaway print spooler for some people (where my request).

  IIRC, people would set their Norton to start a scan and when it was made, the print spooler has run amok at 100%:

  "Because I have Norton Antivirus, do a system scan every Friday night that I happened to see that the value SPOOLSV. EXE is using almost 100% of the CPU of the morning Saturday. It's the only time that it happens, so I simply stop the process in the SERVICES window, and life is good. I don't know why Norton Antivirus it triggers during the scanning process that I couldn't find anything on the Symantec relating to this site. »

  If the problem resurfaces surface, using abduction special tools on their website, you can uninstall your Norton and view the appearance of things without him - you can always reinstall again once, right?

  I disagree with Norton in general for its CPU and memory hogging and known interference with other XP processes (such as the restoration of the system), so I'd keep which in mind if the problem returns.

  A few years ago, I used to like Norton correct, but will never go back or recommend it.  Microsoft Security Essentials with it's lower overhead and footprint and some regular on the analyses at the request of the MBAM and SAS should hold your own system based on your surfing habits.  Your system will reward you with an improvement in the overall performance of the system as well.

  I can tell you that no single AV tool seems to know everyting so it is safe to use several respectable scanning tools.  Norton certainly doesn't know everything.