Example: HP 15-F009 model: administrator Pssword problem

Similar Questions

• Windows freezes loging screen cannot loggon as administrator (same problem with UAC)

  Here's my problem:
  When I turn on the PC, it starts normally until I get on the page user/session/welcoming... I can enter any user with any problem (normal) session...
  But if I try to log in to the administrator, windows crashes on "welcome blue" (the welcome circle does not move, pc does not)...
  I tried in safe mode, same thing...
  And I basically can't do anything, because when I want to perform an operation of fixing or something else, I need access to administrators on other sessions. And when I try to install something, for example, the UAC asking and asking an admin loggin, when I enter the password and press ENTER, it freezes!
  So, my Admin session seems to be corrupted
  And of course I can't perform any recovery or repair windows system...

  I tried to find similarities with my problem but failed so far.
  I suspect:
  -Updated to Avast which freezes the boot process (but to fix it, the solutions are simple but needs to be admin! as edit msconfig or uninstall Avast)
  -Windows update as well and patches exist for this problem but once more, it takes an admin to install theses
  -Malware but can't run any anti-malware!
  -Damaged Winloggon.exe or field
  -Registry errors
  ....

  There are solutions for each of theses, but I can't try something without admin rights...

  I said that I also have a Linux OS (ubuntu) on my drive and I can access C:/Windows (NTFS) file of it.
  What I would do:
  -Hack/create a new admin session (doable with a live CD, apparently, so can I do since ubuntu?)
  -Try to repair windows with the installation CD (but so far I haven't found it yet)
  -Restore the system from the last known good configuration
  And another problem here, starting with F8, I can only start with:
  + SafeMode
  + SafeMode with network drivers
  + SafeMode with cmd prompt
  and no other choice

  I'm looking for help

  The cause of your problem appears to be a corrupted profile admin.

  The cause is your dependence on a single administrator account. It is also risky to have a key to the House. Sooner or later, you lock you up. A fully tested alternative admin account you would save a lot of grief.
  If you send me a note so I'll tell you how to solve the problem in less than five minutes.
  pegasusDOTfnlATgmailDOTcom.

• The BIOS administrator password problem

  Hello. Im having a problem with my computer Bios administrator password. I remember I put a password once, and then I removed the password once again, but now that I formatted my pc and returned to windows 7 ultimate, when I press F10 it asking me a password. I tried to put the same password I used the first time I tried, but it was not valid. I tried to put my user password is the administrator user, and it did not work... After 3 passwords, it shows me the numbers and I can't do nothing but put it off and on again.

  What seems to be the real problem? can someone help me? I need to make some changes in the video memory Bios.

  My laptop is a HP pavilion dv6-2150us, inter core i3

  Ok.
  Try the following
  60783438
  
  Please don't forget to share your positive or negative result with the community.

• HP Envy 3570nr: administrator password problems

  I have just returned from holiday and got the lock screen when I did research online I could not find a code for my code wrong password which is 54148215. Please help to add that I'm back to work tomorrow and use this laptop

  Hello

  Enter: 41820831

  Regarding the other issue mentioned in your MP, try the following.

  Hold the ctrl and alt keys, then press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When system restore interface has loaded, select a restore point at least 48 hours before the problem arose first and then proceed with the restoration of the system.

  Kind regards

  DP - K

• Example of analysis of spectrum at large problem band

  Hello world.

  I downloaded the example of analysis of spectrum to broadband and tried, but it doesn't show any of the spectrum.

  http://www.NI.com/white-paper/13882/en

  Configuration:

  Anritsu MG3700A ==> NI USRP2920 vector signal generator (connected to PC Windows7)

  FREQ. 10-50 MHz

  Power 0dBm

  Are there any suggestions?

  Hi Morse 1125,

  What driver version are you using?  I assume you are using version 1.0.  I looked in the RxHWParameters.vi block diagram nodes property subset since this is where the error message indicates the error comes.  There is a call to the Active Channel property.  This property is new for the driver NOR-USRP 1.1.  The driver update should resolve this error.

  You can find the driver 1.1 here.

  Update the driver, you will also need to update the firmware and FPGA image.  Here 's a knockout that explains how to do this.

  Let me know if this does not resolve the problem, I'd be happy to help you.

• Example: Computer Hp laptop: computer administrator Hp laptop or power on password does not

  My hP laptop model # G7-227WM WITH WINDOWS 7 Home Edition on initially turning ask an administrator or a power on password and I never set one and im the owner of it. I haven't used in 3 years and I have none of my systems how to reset or recovery disks it I'm not sure that everything is on it but really don't care id I lost it as I used it for school and well after these days now.

  Hello

  Use the code to reset below

  33749995

  You can:

  1. use the unlock code you generated to enter BIOS

  2 disable all passwords that are enabled in the Security menu of BIOS.

  3. If the request for current password - enter the unlock code

  4. for the new password, simply press the ENTER key

  5. repeat the same thing to check the password column.

• Administrator password problem

  I have a HP Pavilion dv7 laptop running Windows 7.  I have problems with it starting and leaving me with a black screen with just my cursor showing.  I can't do anything with it.  I could get the command prompts at the start to where it gives me the opportunity to leave the computer to repair itself. However: when I click on it, it forces me to submit my local/admisnistrator username and password before it will enter the phase of repair.  I never put the password that I remember and we tried on every password that I can remember never use without result.  This is the first part...

  I was able to get a screen that asks me to a self diagnostic run on the test at startup computer.  The result is:

  Memory test: past

  Smart Check: spent

  DST short: failure failure ID: RU63NO - 58H & 4 s - XD002J - 60XR03 product ID: WA794UA #ABA

  Can someone help me with this problem.  I don't know what to do, and can't afford to take it to a computer specialist.

  Thank you

  Jack

  DST failed message indicates the hard disk has failed or is failing fast and must be replaced. If you are still in warranty HP will send a replacement. If this is not the case, a laptop SATA hard detail can be used. Just be sure to get a quality at least equal the original in order to use recovery disks. It may be big, but not small ability more. For example, you have a HDD 500 GB so that you could use a 750 GB hard drive, but not a 320 GB hard drive.

• Administrator of problems downloading

  I am trying to download Adobe Digital on my computer at home.  When I choose to SAVE, I get a message saying that I am not the administrator.  How I became the administrator or bypass to continue on?  Thank you.

  Hello

  Thank you for writing to Microsoft Communities.

  To find the list of local, make user profiles right click workstation, click Properties and then click on settings under the Advanced tab in the user profile.

  Method 1: I suggest you try to install the software with administrator privileges and check.
  a. right-click on the configuration file and select run as administrator.

  For your reference:

  Change the type of user account: http://windows.microsoft.com/en-IN/windows-vista/Change-a-users-account-type

  Please follow these recommended steps and post if you still experience the problem.

• HP printer model k110a INK PROBLEM

  Hello people!

  I'm having this problem with the model of HP printer (Deskjet Ink Advantage 2060 all)... I bought it just because of its cheap ink cartridge and now it's the BIG problem.

  For this stupid ink, I had my black ink smeared anytime I pinned, touched with a bit of sweat on the hand and as photocopied kena if I write something that precedes the paper... and the quality is right etc... as newspaper quality and perhaps worse than?

  the used ink cartridge is 704.

  So, anyone could contribute to improve the quality? Maybe I need to fit in the printer setting?
  Or, can anyone tell me is it possible if I change the cartridge to another model?
  Or, is it advisable to change it in external ink?

  I want this printer to fix... desperately...

  PLEASE HELP ~ ~!

  Thank you very muchiii ~!

  wenxt, have you tried going to the Printers folder on your computer (sometimes called "Devices and printers" or "printers and faxes" depending on your operating system) and by changing the printer preferences?

  Find the copy of your printer and right click on it. Go to "Print Options". Here, there should be a tab of quality, and you can select your printer to print in draft mode. This should reduce the risk of smudging.

  Also, the impressions with considerable amounts of ink will be dry longer than plain text documents. Don't forget not that you give the documents that you print the appropriate amount of time to dry.

  Let me know if it helps!

• HP ALL IN ONE model No. F4488 problems

  Printer: HP ALL IN ONE model No. F4488

   

  Serial number[personal information]

   

  Purchase date: November 29, 2009

   

  Operating system: Windows XP

  The problem occurs when I tend to print/copy unique documents. In most paper jams in the print area on time and I have to open the printer cartridge box and remove the paper with your hand. In addition, my top corner of the page is usually torn or cut a little bit. I don't know how to correct the problem. Please help me.

  My contact id:

  Name: David [personal information]

  Hey prateek03jan,

  I see that you have a problem with paper jams in your F4488.  I advise to check to make sure that there are no small pieces of paper caught in the inside of the printer or pick up pebbles.  Often, this can lead to jams in the unit and the torn/crumpled pages as you described.  I would follow the troubleshooting steps in the document below.

  "Paper jam" message appears on the computer

  Hope this helps,

  Jason

• Logon administrator password problems

  I have 3 accounts of different profile on my computer.  I can't connect to one of the accounts which is be the administrator.  I get an error saying password failed.  I have not set up a password on any of the accounts, but all of a sudden it says I need to have a... I don't know if someone using my computer accidentally entered a password and I have no idea how to get around that!    I'll try to remove and to put in place another but I can't do because he will have the password of the administrator.

  Thank you!

  Hello

  In this scenario, the only way to reset the password is to use the password reset disk. If you have created the disk of your computer, you can check out the article below to use.
  http://Windows.Microsoft.com/en-us/Windows7/reset-your-Windows-password

  Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features. For more information about this policy, please refer to the sticky below.
  http://social.answers.Microsoft.com/forums/en-us/w7security/thread/39f56ef0-5d68-41AD-9daa-6e6019c25d37
  
  Hope this information was useful.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• "You must be logged in as an administrator to install this program" error when I AM logged on as administrator. possible problem with TrustedInstaller security

  I am logged in as administrator on the single computer.  I try to install Net Nanny, which claims to be compatible Windows 7.
  The first time I tried to install it I got the error, simply, 'access denied '.  After several attempts with the same error, I rebooted in Mode safe mode with network and then got the error that the Windows Installer Service is not accessible.  After some research, I discovered that Windows Installer is not available in safe mode.
  So I booted in Normal mode.  Logged as administrator.  Tried to click with the right button on the installer downloaded for Net Nanny and ran as administrator, the connection of the administrator.  Now I get the error, "You must be logged in as administrator to install this program."  I am.
  I closed all firewalls, anti-virus software AND turn off the UAC.  I checked the compatibility AND security for the download tab and it is configured to run as administrator and I tried to run in several modes of compatibility.  I still don't "You must be logged in as administrator to install this program."  No matter what I try, I still get this error.
  I used the command prompt, type msiexec.exe / unregister, and then msiexec/regserver.  No new results.  Still the same error.

  I called Net Nanny press SEVERAL times and they will know that this is a Windows problem, because this is the first time that they already got this error.  They had me to download another file on a mirror site.  Not always the same error.  People what I'm doing wrong?  I was able to successfully install other software.  Thanks for any help!

  UPDATE * I am researching always this.  This would be a TrustedInstaller security problem?  If this is the case, is it possible to fix the TrustedInstaller or turn it off?  The big question, is that I want to turn it off?  My first thought is 'no '.  However, this software is listed on the Microsoft site as being compatible with Windows 7.  Therefore, an application that is 3rd party that is accepted by Microsoft.  Wow, I'm confused.  Don't know what to do here.

  Hello carpetfresh,

  A test, I temporarily disable user account control and then see if you can install Net Nanny. If so, we know that UAC is what is causing the problem with the installation.

  1. access control panel user to the Start Menu-> Control Panel-> user accounts and of security for the family-> user account

  2. click on the settings of the user account controll link.

  3. move the slider to never notify

  4. click OK for the changes to take effect

  5 reset.

  Once you have correctly installed the Net Nanny, then back to the control panel and reactivate the UAC.

  Answer please come back and let us know.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Administrator access problems to change files.

  I upgraded from vista Home premium 64-bit for win 7 Home premium 64-bit and am logged into my main account and it says administrator under my name, but when I go to edit some files it does not do and says I need administrator access to say COMPUTERNAME\MYUSERNAME.  I make sure that I am logged into my account, but it doesn't let me do anything.  Help, please.

  Hello
  Welcome to the Microsoft answers site

  If logged in as an administrator, there could be some files that require the possession.
  To change the files you must have the owner of a protected file to access. If another user has restricted access and you are the computer administrator, you can access the file to appropriate.

  To take ownership of a file, follow these steps:
  1 right click on the file you want to take control and then click Properties.
  2. click on the Security tab and then click OK in the security message (if one appears).
  3. click on advanced and then click the owner tab.
  4. in the name list, click Administrator, or click the Administrators group, and then click OK.

  The administrator or the Administrators group now owns the file.

  To change the permissions on the file that you now own, follow these steps:

  1. click on Add.
  2 in the enter the object names to select (examples) list, type the user or group account that you want to have access to the file. For example, type administrator.
  3. click on OK.
  4. in the group or user names list, click the account you want, and then select the check boxes of the permissions you want to assign to this user.
  5. When you are finished to assign permissions, click OK.

  6. you can now access the file.

  For more information, you can check: -.
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-access-denied-when-opening-files-or-folders
  Note: The steps are for windows XP. However, you can give a try for windows vista and windows 7

  It may be useful
  Thanks and greetings
  Support Microsoft-dieng
  Visit our Microsoft answers feedback Forum and let us know what you think
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/

• Recently programs will not be installed unless do a right-click and do 'run as administrator '. Problem of UAC (User Account Control).

  I suspect something is wrong with my installation of Windows, what can be done to make the programs to install normally, which is more secure (doesn't allow not programs administrative privileges during the installation).

  The "User Account Control" dialog box never appears like this: http://goo.gl/CbsXF

  Thank you
  Dan

  Hello Dan,.

  Create a new user account and check if the problem persists, if the problem does not persist in the new user account, then you can fix the damaged user account.

  Create a user account

  Difficulty of a corrupted user profile

  Hope this information helps.

• Oracle SQL Developer Data Modeler 4.1 problem

  Hello:

  I m trying to use the new version 4.1 (BETA) of Datamodeler, but I have a problem at the time wherever I run the program.

  When I work the datamodeler.exe the console show me:

  UIDefaults.getUI () failed: no class ComponentUI for: oracle.ide.controls.StatusBarControl$ JDevStatusBar [, 0,0, 0 x 0, invalid...]

  Can you help me?

  Thank you.

  Hello

  Data Modeler 4.1 requires Java 1.8 can run correctly.

  If you try to run Data Modeler 4.1 with Java 1.7 it gets stuck in "Save the Extensions", and this error in the console log.

  When you try to start with Java 1.7 it normally gives a "JDK Version not supported" warning, which identifies the file that needs to be updated to refer to a jdk Java 1.8.

  Under Windows, this will normally be C:\Users\\AppData\Roaming\datamodeler\4.1.0.866\product.conf,

  But if you start from the console using the datamodeler64.exe it will use the file

  C:\Users\\AppData\Roaming\datamodeler64\4.1.0.866\product.conf instead.

  You can change this file.  Alternatively, if you delete the file, it should display the dialog box asking for the location of the JDK next time.

  David