Factory default software start startup Satellite L650 / 07C first time

Similar Questions

• Re: Satellite L650/07C-boot-loop after memory upgrade

  I have a Toshiba Satellite L650 / 07C - PSK1JA-07C017.
  To get a little more life out of it, I've updated yesterday with a SSD and 8 GB memory.

  The SSDS works perfectly and I have installed OS and all the drivers and software.
  However, the memory causes a boot loops. I returned to the standard 2 x 2 GB memory at the moment.

  With the new memory installed, the computer startup-loops. When you try to start Windows, the computer will appear at the stage of loading Windows (the boot animation) and then restarts.
  I tried to start with the recovery discs, and it arrives at the stage of loading of Windows Setup, and then restarts.
  She will continue trying to start, then by restarting (then repeat), until I turn it off.

  The memory I installed is Corsair CMSO8GX3M2A1333C9 (2 x 4 GB):
  http://www.Corsair.com/cmso8gx3m2a1333c9.html

  For me, it looks like the same specifications that the modules of memory Kingston 4 GB listed on the Toshiba site as being compatible with my laptop:
  http://www.MyToshiba.com.au/products/Accessories/memory/KTT-S3B/4G/accessories

  I found the specs of memory recommended here:
  http://www.LASystems.be/PDF/Kingston/246787/KTT-S3B4G.PDF

  If I go into the BIOS, I see that the memory is detected as 8192KB. The Toshiba site says that this laptop is expandable to 8 GB.

  Is there something I'm missing?
  Is there another step I need to perform when upgrading their memory?
  I don't know why it won't boot with the new memory modules in that I put.

  Thanks for any help you can offer.

  I assume you have the Australian model is not easy to find info on the hardware upgrade. What I can say is that model European uses DDR3 1066 MHz memory modules and 4 GB of RAM compatible a part PA3677U-1M4G number.

  It must be exact model described by microcens.
  I recommend you use the tested and compatible memory modules.

• Re: Satellite L650 / 07C - HDD (Hard Drive Impact Sensor) shock protection system

  I just bought a Satellite L650 / 07C. When I bought it from the dealer, I was under the impression that this model came with the function disk hard drive shock protection system (hard drive Impact sensor).
  I ran the Toshiba PC Health Monitor application, but it seems not to have this function - it gives me the power settings, Temp and fan are monitored, as well as a status of hard disk drive, but nothing on the disk hard drive shock anti-siphoning (hard drive Impact sensor).

  Under my file utilities Toshiba HDD SSD Alert application that shows the same icon as the one I saw in the reseller on their Toshiba Satellite when they did there evidence the shock protection system. I ran this application, but it gives me just a status message that the drive works properly.

  Could someone please confirm with certainty whether the model I have this feature.

  Thank you very much.

  Everything goes well with your laptop. I made a screenshot and uploaded to show you:

  http://img135.imageshack.us/img135/788/shocki.jpg

  When you shake your portable hard drive ssd aler appears, however, you can disable it appearing.

• Windows 7 won't start on Satellite L650

  Hey,.

  I went to turn on my laptop this afternoon and windows does not start. I get the loading screen animation, but nothing happens. When I restart, I get the option to repair windows - but when I go in, all I get is a black screen with a white cursor.

  I tried the following:
  -Switch on my computer and now the F8 - nothing happens, I just get to the screen asking me to repair windows or start normally
  -Engraving of windows Recovery Center 7 on a CD and it works - nothing happens, black screen with white cursor
  -Turn on the computer while pressing the 0 to get to the system recovery - again, nothing happens. The black screen, white cursor.

  It is only 3 months old so it is still under warranty, but I prefer not to have to take it to a service center because I need for work, and I can't do without it for more than a few days.

  Any help or advice would be appreciated!

  Thank you

  > I guess now, my question is - why is this happen?
  Who knows things boyfriend arrive simply because on no apparent reason
  But although it works again

• My screen freezes 1 min after that I start my PC (only the first time) then it works throughout the day

  It only freezes once and for some strange reason windows crashes when I click on Administrative Tools.

  Additional information from the double wire:

  I have absolutely no problem, except that Vista freeze 5 min after the first start of the day, and then it works fine.

  I also run a memory test and it found nothing.

  It's a hardware problem, because the problem persists after reformatting. Thanks for making me reformat the computer, guys.

• E5 - 575G Factory Default Backup

  I tried to create a backup of such factory default recommended in the user guide, but every time it fails with "we cannot create the disc of recovery-a problem occurred during the creation of the recovery drive.

  Any way around this error?

  I would say Macrium Reflect free back up your system, it is very eaasy program and reliable, follow my links for download and tutorial.

  http://www.Macrium.com/reflectfree.aspx

  http://www.Macrium.com/webtutorial/tutorial.asp

• Satellite L650 periodically starts

  I recently bought a laptop Toshiba Satellite L650 with Win7.
  He worked for a few days and then periodically wouldn't start upward.
  Can help you? I installed only anti-virus application.

  Hello

  I recommend the HARD drive recovery procedure that helps you define the computer laptop back to factory settings.

  Then you need to test the laptop once more, in my opinion, this should be done first because it of really difficult to tell if the problem is hardware or software related both recovery would provide more information

• Satellite L650-12 q keeps freezing whenever I have start the video or the phone call

  Hello

  I recently bought a portable Satellite L650-12 q who played perfectly until I tried a video MSN Chat (MSN messenger and Skype). Within seconds of starting the conversation, the computer crashes completely. I get a static screen and nothing works just so than ever and all I can do is press the button works / stop.

  I'd appreciate it really any advice on why this is happening and how can I fix this please?

  Camera assistance software running in the background all the time (starting with Windows)?
  Try disabling it in the start menu > run > msconfig > startup and check again.

  To be honest I have never heard of this issue and especially there is no problem with Skype.

  By the way: have you checked the Skype video settings? There is everything OK?

• Satellite P200D Factory defaults recovery

  Hello

  I post here in the name of an old man who bought a Satellite P200D-PSPBQE, S/N 28160997 K (Vista Home Premium French) who has gone through a series of problems. He cannot attend his book himself and so asked me to fix it.

  The laptop has especially worked for two or three years until this summer when it has overheated (as I can judge by touching the case) and switched automatically a few times off the coast. At one point the laptop wouldn't even step to the BIOS.

  Here is a rough summary of what I did then:

  I began to open the case, but it seems too difficult, so I closed it back and use a vacuum cleaner to clean the dust in the vents, restarted the laptop and it are returned and very well for a while. At one point, the owner of the laptop mentioned a small bug crept once out of the laptop but I don't mind at this moment.

  After some time, Vista has experienced various gels (maybe explore buggy but I couldn't judge I never looked in the event viewer that I had no idea what kind of help the EV could bring until very recently). I thought that this could be due to the many automatic switchoffs who listens to the Vista system files. I ran sfc/scannow, who pointed out a few errors, but cannot fix them. Yet it is not attached to the gel. I stuff ready for the usual save the data/reinstall vista and drivers/restore cycle data.

  On the recovery discs: I asked the owner for all Toshiba drives, but it didn't, not even the recovery disk based 100MB.

  I thought that automatic recovery of factory default partition existed but that he could not find its start-up in the manuals coming with the laptop. I was curious and thought, Hey, I'll start the recovery partition myself with a boot partition tool. I ran the Partition Magic CD reported contradictory of the partitions on the first drive, which prompted me to repair it with suggested partition table values: I stupidly pressed Yes and then not really started (or so I think). I couldn't see any recovery partition only two 80 GB system partitions, and data were present. A race of Ranish Partition confirmed it.

  Yet, I tried to turn on the laptop while pressing '0' at the same time, as stated in some tech forums but it didn't not start any recovery procedure at all.

  I could not find the recovery disk creator in the menu program so I downloaded and it started and it reported, no partition recovery not found.

  As I found myself helpless without any recovery solution (I had not heard backupmedia.toshiba.eu) I downloaded a copy of Vista of P2P (Yes, it's bad, but I was impotent). This laptop has two hard drives of 160 GB, of which the second was not used. I exchanged the places of two readers, installed Vista using the product key from COA to empty disk. I installed the display driver and the retrospective data is restored and the laptop is back on the spot two, running OK, but still from time to time of freezing.

  Finally, I decided to call the assistance of Toshiba in France who reported to me on the backupmedia.toshiba.eu site where I can order recovery disks.

  _Before I order backup disks I have a few questions: _

  Can I open the case and do a thorough cleaning of any dust remaining/bugs/etc? (I guess that the answer is Yes) Are there instructions for that?

  Maybe hit the cpu overheating. Should I run a test of cpu and which?

  Overheating may have affected the memory modules. Running Windows Memory Test enough or do I run Memtest 3.x or later version to check the memory sticks?

  Is there really a recovery partition on the hard drive of this series (P200D-PSPBQE) system? If Yes and given the Partition Magic probably changed only the partition table, is there a way to restore the original partition table values and thus to restore access to the recovery partition? That would save me the trouble to order backup discs.

  backupmedia. Toshiba.EU offers you to order a backup for 35 euros drive about it's a drive to restore default factory containing Vista, drivers and tools, or just the basic restore disk that starts (currently absent) recovery partition? In the second case, how to restore the laptop to original factory settings?

  Thank you for reading this far, sorry for any English mistakes and thanks in advance for any input,
  Eric Ivanov,
  Grenoble, France

  > Should I open the suitcase and do a thorough cleaning of any dust remaining/bugs/etc? (I guess that the answer is Yes) Are there instructions for that?

  I wouldn't recommend disassemble the laptop. This should be done by a mobile technician who knows what to do if you want to remove dust or debris from cooling vents, I would recommend using a jet of compressed air and you may suck dust.

  > Overheating may have touched the cpu. Should I run a test of cpu and which?
  Perhaps this is possible, given that the laptop is two years (or more) and during this time, a lot of dust might collect inside the cooling modules.

  > Overheating may have affected the memory modules. Running Windows Memory Test enough or do I run Memtest 3.x or later version to check the memory sticks?
  A higher temperature can affect all parts of the laptop also memory, it was the case in my old notebook. BSOD was always because the memory could not be cooled. But I doubt that memtest would help you if the higher temperature would affect modules

  > Is there really a recovery partition on the hard drive of this series (P200D-PSPBQE) system? If Yes and given the Partition Magic probably changed only the partition table, is there a way to restore the original partition table values and thus to restore access to the recovery partition? That would save me the trouble to order backup discs.
  You cannot restore the HARD drive recovery partition. If you are not able to start the HARD drive recovery (pressing F8-> fix my computer-> HD recovery), you must order the disk from Toshiba Web page.

  > backupmedia.toshiba.eu offers you to order a backup for 35 euros drive about it's a drive to restore default factory containing Vista, drivers and tools, or just the basic restore disk that starts (currently absent) recovery partition? In the second case, how to restore the laptop to original factory settings?
  This s recovery disc that contains the image of Toshiba. Toshiba is a package that contains the Windows operating system (Vista), drivers, tools and additional software. Simply said; This disc would fix the laptop back to factory settings.

  Hope this might help a little.

• Cannot perform factory reset to Satellite L650

  Hi team, support

  Hope you will be well :)
  I have some problems and hope that you will help me solve them. Here is the description of my problem:
  I have a Toshiba Satellite L650 - 17R laptop computer I want to reset to the factory settings. I used the following instructions to do that (http://aps2.toshiba-tro.de/kb0/HTD1303440001R01.htm), but when I'm in pressing the F8 key when starting laptop it appears a list of choices on the display that does not contain 'Repair your computer' or "??" or something like that. The first entry in this list is 'Safe Mode', second is 'Safe Mode with Networking' and so on. Also, I tried the other method described in many places in the internet, which is to press 0 and the whole power button when you turn on the laptop. In this case again, he starts to do things as described in the instructions (example here http://www.youtube.com/watch?v=I5dEOm1EJBw): it beeps, then when I let go of the 0 key, it prints "starting Windows" and shows the Windows logo, after that it goes to market as always and no other dialog boxes appear.

  Issues related to the:
  Is there another way to do the factory reset?
  I have doubts that the "Toshiba HDD recovery" tool of my laptop is corrupted, so is it possible to download this tool on the internet, on dvd disc and install from there? If so, then can you please give me a link of this tool for my model?

  Best regards
  Mihran grabbed.

  Hello Mihran and welcome in the Toshiba forum

  Let's see what's not there.
  First some general info. Each new Toshiba notebook is preinstalled with original recovery image. This image is also saved on the HARD disk on a separate partition. With the factory settings repair my computer option will appear in the advanced start-up (F8 at startup) and HARD drive recovery option can be made as described in Toshiba document you posted in your first assignment. If nothing is changed, this option will be there and you will be able to do the installation of HARD drive recovery again ad again.
  > when I'm in pressing the F8 key when starting laptop it appears a list of choices on the display that does not contain "repair your computer".
  This occurs if you have installed the version of the OS using the Microsoft installation disc. After having this option to fix my computer will disappear, and you will not be able to start the installation of HARD drive recovery.
  > Is there another way to do the factory reset?
  Yes. You must use the disk for the installation of the OS restore DVD. After that it all will be the same. Repair my computer option will be available again and you won't be havce factory again.

  If you have any other questions you are welcome.

• Satellite L650-12 q - slow very slow start & preformance

  My laptop is a Satellite L650-12 q with Windows 7 home premium 64-bit, intel core i5 - 43 M and 4096 MB of RAM. It works very well but begins to be a little slow last weekend, I've defragmented it and it got a little better. Then two days ago you 22mins at startup (& login) and an another 7 minutes just to open all programs. It is slow to seriously.

  I have defraged there once again, run the Tuneup Utilities (who says there is nothing to the difficulty to start), run my antivirus & anti-malware and it starts in safe mode. Even to start diagnosis and almost all startup programs off it makes virtually no difference.

  In total, it takes 10 minutes to get from the start 'windows' to my login screen then another 5 to get to my office. If I want to open a document in word or firefox, then yet another 3-5 minutes so he can come and start running slowly. Does not better it's on, but not by much.
  Any help would be greatly appreciated, even if it's to tell me that it's time to get a new laptop :)

  No, it is not the time for the new laptop computer.
  Of course we don t know how did you use your laptop, what additional software you installed and how you configured OS so in my opinion, better than you can do now is to back up all important data and install the OS by using original Toshiba recovery image.

  After doing this you will own preinstalled OS and everything should be OK again. Please test a few days without changes and post comments.

• Satellite L650 - 12K - restore the factory with Windows password settings?

  Hello

  Today I received my new Toshiba Satellite L650 - 12K. I went through the process of "first use" and put in place my name of user and password Windows 7 etc.

  However, after a reboot, when I tried to enter my password to connect to Windows, it says it is incorrect. I tried different combinations of password I used (I know what it's like I wrote it down at the time)-ive tried caps, plugs etc but nothing works.

  If I order the Toshiba recovery disks I will be able to return the laptop to factory settings and start the installation again, including Windows?.

  PS - I only put an account so can't even connect you as another user.

  Thanks for your time and your help.

  Gary2802.

  Hey Buddy,

  Yes, the Toshiba recovery disc can restore the initial configuration (on the box settings) even you don t know the password because it will remove the whole HARD disk and restore the version preinstalled Windows from Toshiba.

  So don t you worry about this, Toshiba Recovery disk will help you! ;)

• Satellite L300D - how to restore factory default and USB key?

  Hello

  I need urgent help. I got an error on my laptop and I lost my recovery disc, so I borrowed a friends disk by mistake. I deleted the partion that everything has been installed on.
  Can someone please help urgently? I have all my files on a USB key and really need to give a presentation on my laptop by Thursday September 23. Can someone please? I read about a secret partion on laptops to default factory default

  concerning Ross

  Hi elrossco22,

  What Satellite L300D, you have exactly and are - this a European model?
  If yes try to access the Windows Advanced Boot menu and choose fix my computer. Then, you can start the recovery of HARD drive feature.

  If this isn't the case, you need a new Toshiba Recovery disk to restore to factory settings. You can order such a drive here but it s for European models only:
  https://backupmedia.Toshiba.EU/landing.aspx

• Re: Satellite L650 stuck Startup Repair mode

  Hello

  I was asked to look at the Satellite L650 laptop for a friend because they could not get going.
  Not sure they did before me do yesterday, as far as I know, it's that they couldn't turn it on. I wanted to get into Safe Mode, but it went to the Startup Repair Mode and is stuck in this at all times.

  It is currently running Windows 7 Home Premium 64-bit.

  Have you tried from the DVD player, but it is up to the use of the hard drive, even tried running in my network, but without a bit of luck.

  It does not go to the repair step because it gives me the opportunity to enter a password.

  Someone at - it ideas how I can work around this problem, you can.

  HAL

  Hello

  I think you have only two options here:
  (1) you are going to use HARD drive recovery options
  (2) or you can start the recovery using the recovery disk

  For HARD drive recovery:
  http://APS2.toshiba-tro.de/KB0/HTD1303440001R01.htm

  Recovery disk:
  A friend created one in the past?
  Isn't it? Well, the new disc can be ordered here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Satellite L650 - 1 M 0 - Question about LED control using a writing software? in C++

  Hello

  Is it possible that a console program written in C controls the State of the led on the computer?
  I speak not here the LED keyboard, but the led corresponding to such a State of hard disk, power state.

  It's at all the possibility to 'take control' over these diodes? Or rather, it controls a separate computer system?

  Most of the care on the State of control module LED WiFi adapter. I replaced the network card, but my laptop is not the end of support. Start the computer, but you can't control adapter to function keys. When you disable the card in Device Manager, the light does not turn off.

  If I could create a program that will control the LED, if I could take a supplement (separate second program) for the function keys, which does not support the new card.
  Laptop is a Toshiba Satellite L650 1 M 0.

  I think that computer security is not strong because it is not protected from the BIOS. If it was, wouldn't at all. Only the lack of logic LED WiFi.
  By taking the scientific program caught can control the LED.

  Please be patient with me and write in plain English-the two shows (I'm a novice programmer C++ programming language) and English.
  I don't know English well, so I took the Google Translate. Sorry for my bad language...

  [b] compiler: [/ b] Microsoft Visual C ++ 2010 Express
  [b] software language: [/ b] C++
  [b] type emission: [/ b] console (maybe later I'll try Windows Form...?)
  [b] system: [/ b] Microsoft Windows 7 x 64

  I know that this forum is no longer on the problems associated with technical problems, but none of you can know what is "address" LED WiFi that is already associated with the knowledge of the equipment.

  Hi Krzysiolek

  I guess that no member of the community would be able to help you in this case very particular.
  I guess you should ask for a person with good knowledge of C++ programming.
  Here you can meet people and enthusiasts who talk technology, share their knowledge and trying to solve some common problems of the laptop.

  However, good luck