first firmware update went wrong...

Similar Questions

• WRT160N v2: the latest firmware update went wrong!

  Hello

  I just bought this new thing, it is not connected to the internet (wrt160n-> cable modem-> internet)

  so I tried the last thing: upgrade to the latest firmware 2.0.02
  The upgrade - trial went fast enough at 98%, but remained there for about 3-5 minutes.

  Then finally: successful update.

  It has rebooted, my computer got an IP address again, but still no internet.
  So I went to the page of configuration of the wrt160n, entered ID + password and then...

  ... a screen almost empty! No menu, page actually kind of corrupt.
  I unplugged the router from the power, waited for 60 seconds, retried: same question.

  Any thoughts?

  Thank you!

  Did you try a hard reset, use a pen that I think just next to the power plug to the back of the router there is a reset button with the router connected to the power hold it down until you see the flashing front light put your factory after that

  1. set up your router using the cd that came with it

  2. After setting up is done and you are able to go online try the update again

  that should do the job

• First Firmware update

  We had our UCS B Series chassis for almost 2 years now and it's time to update the firmware of 2.0(3b) at latest.  This is uncharted territory so I wanted to get some feedback from those who have already updated their firmware.  Our servers are B230 M2s and M3s B200 all deployed with the same model of Service profile.  We have 2 Web of interconnections.  All servers are part of a VMware cluster.

  I used this Cisco document as reference to prepare the update: http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/upgrading/from2-0/to2-1/b_UpgradingCiscoUCSFrom2-0To2-1.html

  What I'm not clear on is the steps (which is about everything, there) and I hope that someone can confirm that I have it in the right order.

  1. Step 1.  Download Cisco's UCS Infrastructure support downloads software package.  Also download the Bundle of software Cisco UCS B-Series Blade Server.  I would use the most recent of the two.
  2. Step 2.  Through the UCS Manager, download firmware on the firmware Management tab.  Here, I have the ability to download locally or on a remote server and then recover via a protocol such as TFTP.  Given the option, a local download seems easier.
  3. Step 3.  Install the firmware downloaded to the fabric of the interconnections.  Activate the firmware only on subordinate FI.
  4. Step 4. Update the firmware of the Infrastructure.  Because our UCS is 2.0, we can use the Firmware Auto Install feature. First of all, we are updating MMIC and IOM. Here, I would go in each server individually and click on general, then tab to update Firmware.  Activate the firmware. This restarts the server? The firmware for the adapters is transferred to the INSTITUTION to step 2?
  5. Step 5. Activate the Cisco UCS Manager software via the management of the equipment of the node of the Firmware tab.  Replace the most recent version.
  6. Step 6. Activate the firmware for the IOM. Even as UCS Manager
  7. Step 7. Subordinate the FI for the FI upgrade failover.  Update the firmware on the FI not updated.
  8. Step 8. Update the firmware from the host.  Under Server-policies, we have only a firmware from the host defined.  The only thing to check is the BIOS - an option tab is checked for each of the two servers UCS models we have.  Whence the firmware it come from?  He was included in the package of Infrastructure UCS software?

  And these are the steps that I understand them.  I would really appreciate any corrections or additions.  Thanks for the help.

  You can go directly from 2.0 to 2.2

  Upgrade Cisco UCS version 2.0 to version 2.2

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/upgrading/From2-0/TO2-2/b_UpgradingCiscoUCSFrom2-0To2-2.html

  Steps 1 and 2 must be made

  Actually, the following steps describe the manual process of upgrading.

  However, there is a much easier way; installation auto resp infrastructure servers. (based on host firmware packages).

  (3) as a first step, upgrade UCS Manager for example. 2.2.1c and then you have the automatic installation menu options.

  (4) installation automatic infrastructure

  (5) automatic installation servers

  See, for example. Cisco UCS series B Guide to the management of the GUI Firmware, version 2.2

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/firmware-Mgmt/GUI/2-2/b_GUI_Firmware_Management_22.html

• HP first Firmware Update Failed (104)

  I heard that there is a new firmware for the HP award.

  I connected the calculator for the HP connectivity Kit.   It is an update for both the Connectivity Kit itself and for the calclator.   He managed to update the connection kit, but I can't update the firmware of the calculator.

  I'm on Windows 7 64 bit.

  My current firmware revision is: 2013 8 13 (5106)

  According to the new firware is version_20131125.

  I tried to restart the PC, using a different cable and another USB port.

  The connectivity kit seems to have a solid with the Calculator link because I can view/change settings, etc.

  After a failure the firmare update, I for trombone reset the calculator.

  Any help would be appreciated.

  Sorry in advance if this has already reported and resolved.  I did a search of the forum and have not seen everything about this new version.

  -TIA

  Hi!, gablinger:

  (1) charge the battery to 100%.

  Please, check this link... http://www.educalc.NET/2336439.page

• Satellite Pro P100: Bios Update went wrong - what to do?

  Hello
  I have a satellite pro p100 with win xp.
  I downloaded the bios-update victory.
  something is worng. the laptop was closed and when I try to start it,
  I blackscreen, do not see anything, windows does not start.
  nothing happens.

  Please help me, I write my degree and really need to resolve this problem quickly.
  thanx

  Hello

  so if your machine does not start then you need to send/bring your machine to the next partner service authorized in your country.

  Here´s a link to find one and I suggest you to contact one of them immediately because of your degree:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Good luck
  Good bye

• Last update went wrong. What about the next?

  I upgaded to Design Premium CS4 CS5 on an iMac and it took weeks to get rid of CS4 (as Adobe support told me to do) and get a clean installed CS5.

  On another Mac (Mac Pro), I have CS4 Design Premium and I just bought (not an upgrade) Master Collection CS5.5. I have not yet installed so. Must I first uninstall CS4 DP? Is there anything else I need to do to make the installation of CS5.5 smoothly?

  Thanks for your advice and assistance.

  I'm sorry to hear about this problem, and even if it's not of the never seen this kind of thing is atypical.

  My previous opinion stands. If you really want to delete CS4 use the uninstaller that you will find in the application for each CS4 application folder.

  DO NOT DRAG TO THE TRASH!

  Remember that if you ever need CS4 again, you will need to remove CS5 before you can reinstall it.

  Hope that helps,

  Bob

• New Firmware Update - where is the change log?

  I see that a firmware update was sent to my phone. However I can't find a change log. Where is it?

  Hello!

  HP and Microsoft has released an update (online) of the OTA for the X 3 elite on October 25, 2016. The update installs Windows Mobile 10 for the following versions:

  Firmware revision: 0002.0000.0014.0100

  Build of the OS: 10.0.14393.321

  Bootloader Version: 520101

  New features:

  Area	Description
  Display	High brightness Mode is activated when the brightness adjustment is suggested by default.
  Security	Reset functionality is enabled. However, the existing user must reflash phone with this software with Windows Device Recovery Tool (WDRT).

  The issues addressed (Items with * are fixed by OS updates):

  Area	Description
  Apps	App Instagram, have green lines during use is fixed.
  	Launch of view inconsistent HP on docking tools is fixed.
  Audio	Detection of the helmet is not reliable is fixed.
  Camera	Auto focus performance and stability in low light conditions are improved.
  	Model tapes preview screen is fixed.
  	Video recording after that tap put in pause/resume many times received message 'something went wrong' is fixed.
  Security	Blue BitLocker Recovery screen on reboot with active device encryption is fixed.
  User interface	Tap to wake up the wrong feature turn off screen is fixed.
  Hello Windows	IRIS is unblock, followed by sweeping to unlock quickly led to the prompt error is fixed.
  	Fingerprints and Iris being setup one after the other, one of them will not functional, is fixed. **

  Known issues:

  Area	Description
  Apps	Skype for business app can be run from external display of Continuum.
  Connectivity	Dock desktop LAN port of HP has no configuration of the user interface.
  User interface	Missing tiles with update settings. The user can go to the list of applications, press the settings icon and select PIN to start restoring the tile.
  	Tile 2 Messaging becomes white with update. Touch on the tile once it restores.
  Security	Too many failed unlock attempts, the device will be blocked for security reasons. User can unlock the unit to https://account.microsoft.com/devices.

  Thank you

• HP zBook Studio G3: zBook Studio G3 - DEATH BY INTEL ME FIRMWARE UPDATE

  WARNING!

  DO NOT INSTALL THE UPDATE OF THE COMPONENT OF THE (COMPANY) INTEL MANAGEMENT ENGINE FIRMWARE!

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=8934841 & swItemId = ob_159465_1 & swEnvOid = 419...

  Component Firmware Intel management engine (ME) (American International)

  11.0.0.1194 Rev.A
  December 1, 2015

  We bought 5 of these laptops for our Engineering Department and I was against a tight schedule to get them deployed (the next day). I started working on obtaining a set of installation with the necessary software and then I just want to clone one for the other 5.

  I did a clean install of Windows 10 and installed all the drivers from the HP site. Then I ran Windows updates until everything is up-to-date. I disabled Windows Defender. Now all that remained was update the firmware BIOS, Intel ME and Thunderbolt using the downloaded utilities since the page drivers. The BIOS installed fine, but it's a really weird update process. Due to the beeps and lights blink during his work. There is no progress bar to let you know if she is doing anything. At some point, as the beeping stop but it's still really work. Then he starts and updates another part of the system and so on. Anyway, that everything worked fine. No problem with the update and Windows 10.

  So I ran the update of the Firmware of Thunderbolt and open up a command window saying that it couldn't find the controller. It looks like not there nothing after that point and just closed.

  Finally, I ran the Intel Management Engine firmware update utility. He opens a command window and says that it is loading the file and check and so on. Then he wrote the Flash file and takes a minute or two, doing so. Once it's done, the firm order window and back to business as usual... until you restart. Once you do this, the system is toast. It does not start. Black screen, fans run at high speed and the CapsLock and NumLock bulbs only 5 slow flashes indicating that there is something wrong with the motherboard. I'm starting a supported by HP chat session.

  I am told to disconnect the battery. To access the battery, you need a bit T - 8 Torx and you unscrew 11 screws to remove the grill cover and low fan (pedestal). I did that and disconnected from the battery. Reconnect after a few minutes and tried to start. Nothing, same thing. The support agent told me that a technician on site should be sent to replace the motherboard.

  While the lower lid has been opened, I noticed that there are two small LED lights near the SSD. There are supposed to be the diagnostic lights and I found an article in the service manual indicates if one of the LEDs is lit, the motherboard should be replaced. This lights a few seconds after the connection of the power supply for the laptop or by pressing the power button.

  I asked the support agent if they knew why it happened, but they did not know.

  So, I got 4 portable more to work with. I took off the dead laptop SSD and put a charge in a brand new out of the box. Started by and on the desktop Windows 10. This laptop had BIOS v1.03 on this subject so I ran the BIOS updated and rebooted. All right. At this stage I myself asked to perform other upgrades of the firmware or not. I thought that I had a 50/50 chance and I'm the kind of person that simply be whether it was a fluke or if there really was something seriously wrong with the update of the Intel ME firmware. He ran while first instead of love at first sight to date. Update Intel did ME the same thing before, opened a window to order, checked and then flashed... and after a reboot I got another laptop dead.

  At this point, I shook my head and frowned, looking at the HP logo.

  I tried calling support, but their laptop zbook/computer service has been closed from 10 is no support by phone or chat support. I have to wait until the morning to make a call in warranty for this second laptop dead.

  The Intel ME firmware update released on download of HP ZBook Studio G3 section was not compatible with these laptops and caused the laptop no longer starts. Only an exchange of motherboard could solve the problem. HP since then changed the link to the Intel ME firmware update for the appropriate softpaq.
  
  Those who had run the update of the bad firmware and their laptop brick had to call the HP technical support to schedule a replacement motherboard on the spot.

• FS728TP attention firmware update!

  Too bad, you can ruin a good switch poe by a stupid firmware update. Tried to update my FS728TPv1 to the latest 5.0.0.8 3.0.0.22. Downloaded the zip file, you start the procedure to update with discovery of the smart wizard, message received "updated successfully"... but after reboot the switch is bricked. Did some reading, found I'm not the first guy with this case, should be updated first, startup code from 1.0.0.2 to 1.0.0.5. But it was not a code starting update file in the zip! I found somewhere on the netgear firmware french site the oldest 5.0.0.6, which contains ng_fs728tp - V5006.ros and ng_fs728tp_boot - 1005.rfb. I feel so stupid, I'm?... to open the switch box, found 88E6218-LG01 Marvel, used on some routers 10 years ago chip. anyone find a procedure to revive the switch, a tftp, a series or something connection session. I know netgear offer guaranteed for life and replace the switch, but not my case... just feel sorry a switch of the brick work

  There is a solution, in case you brick the switch to update the firmware, do not update the boot code appropriate. The boot code is some program low level similar to the bios on the card. Did some deep research on Marvel 88E6218-LG01 Chipset, I found somehow that pin 52 and 53 are Rx and Tx respectively to integrated serial UART. The two signals are 12 (Rx) and IC U27 PIN 11 (Tx). The IC and passive components around him are not soldered because the switch is not a serial console. Near U27 is the serial J8, not used. The U27 is a similar to max232 chip. The idea is to make a connection with the switch using p52 series = Rx, p53 = Tx and, of course, GND, I soldered the wires to p11 and 12 of the U27. Then do a session in Hyperterminal using baudrate = 38400, data bits = 8, parity = none, stop bits = 1, flow control = none. Power on the switch, you will see power on self-tests, boot network device based on 88E6218 software version with ARM946E-S then: autoboot in 2 seconds, press return or ESC to interrupt and enter the dance. In those 2 seconds interval if you press the INPUT switch goes to the start with 6 options menu: 1 = software download 2 = flash file Erase 3 = 4 = diagnostic mode password recovery procedure entry 5 = Set baudrate terminal 6 = back. Choose option 1) then the switch is waiting for the firmware file "code using XMODEM download, $$$ writing and waiting...". Now go to hyperterminal transfer, send file > Browse for firmware 3.0.0.22 .ros (before update wrong firmware), choose the XMODEM Protocol, and then click Send. File transfer begins, will take about 25 minutes. After that the switch restarts correctly, and discovery of the smart wizard he found. Update the firmware on 5.0.0.6 family must 1.0.0.5 to update the BOOT CODE. The boot - 1005.rfb can be found on this website: http://www.netgear-forum.com/forum/index.php?s=7d23113dd1660e3c9d613aa739513390&showforum=704 , in 5.0.0.6 zip of the firmware. Have fun...

• Firmware Updater problems :(

  I just download the Sansa firmware update, and when I go to run it, an error message appears saying "the Installation failed. Please try again later. "I started again and received the same error message. Then I waited about 30 min. and sure enough, same error message. What I'm doing wrong!

  OK, the fact is that 90% of us who have been here very long you will simply ignore the update. On the "rocket", go to settings > system settings > Info and watch the number of Firmware if it starts V01 access the Thread called Fuze Firmware Updater, in the first post to find the update of the firmware that starts V01 and then follow the instructions on this post. If your Firmware number starts V02 find this firmware and follow the instructions.

• WRT54G v4 unusable web interface after firmware update

  I tried to upgrade (actually downgrade) my WRT54G v4 firmware 4.30.11 to 4.21.1. When the progress bar reaches the mark to halfway, I got the message saying that the upgrade was successful. However, now the web interface is so messed up that it is unusable. It's a sign that something went wrong.

  Power, WLAN, Ethernet 1, and Internet lights are all green solid, which should be a good sign. After the upgrade, the web interface says "WRT54G 4.21.1', which is the firmware messed up I am downloading. Browsers, then restart my computer, I have confirmed that it is a router problem, not a problem of the browser cache. I also tried to do a hard reset by pressing the reset for 30 seconds button, unplug the router while holding down the button of reset for 30 seconds and then plug the router while holding down the button of reset for another 30 seconds. This has not fixed anything.

  I encountered a similar problem after an update of the firmware several years ago and the fix to upgrade the firmware using TFTP. This time, however, the TFTP utility could not download the firmware. Using a hack that I found on the internet, I have re - download the 4.21.1 firmware, but the web interface was always messed up. I then downloaded the 4.30.13 firmware. The web interface is still messed up, but then he said "WRT54GL 4.30.13. I then went to the firmware I wanted, WRT54G 4.21.1. The web interface is still screwed up, but said «WRT54G 4.21.1»

  Anyone know how to solve the problem? Yet once, it took place immediately after a firmware update, the web interface is unusable, is not a problem of the browser cache and tried a hard reset.

  Thanks in advance if anyone can help.

  My router model is WRT54G v4. The v4 WRT54G and the WRT54GL are generally considered to be the same device with different model numbers. According to the article of Wikipedia WRT54G, "the WRT54GL is technically a reissue of the version 4 WRT54G."

  I used the firmware 4.30.X for years without problems. However, I decided to switch to the 'right' firmware for my router and something went wrong during the upgrade.

  I solved the problem. I basically just dropped the Linksys firmware and uploaded the DD open source-WRT firmware mini instead. Now everything works fine.

• Wan interrupts the connection after the firmware update

  Looks like the latest firmware upgrade is the source of the problems.

  I've just updated my timecapsule 1 TB of first generation version 7.6.7 and my 3 TB timecapsule new version 7.7.7

  Both are connected to the router of the provider of Internet services and extend the network even in my house.

  WiFi is stable until the upgrade, but now the connection is lost every few minutes or seconds.

  Both versions are later to the respective timecapsules.

  I end up having to downgrade if no solution is found.

  I powered the two market still nothing does not. Redefine the network and tried both hidden and not hidden, yet once nothing doesn't.

  Any ideas on what is causing the problem?

  Well, since nobody seems to have an explanation, and Apple are not out with firmware update after 7.7.7 and 7.6.7 I decided to downgrade the firmware to the previous version. I now run version 7.7.3 on the new 3 Tb Time Capsule and 7.6.3 on the 1st Gen Time Capsule. So far, the network is stable. Using WiFi Explorer Ii see that they use channel 6 and 8 respectively. Signal is strong and no dropouts have taken place so far. Hope the issue is resolved in the next firmware update.

  As I read in another post: firmware update does not solve a problem, you didn't. However, it can create a problem that you didn't.

• Airport Extreme Base Station model bricks A1408 after failed firmware update

  Shown on Macbook Pro iOS X 10.10.5 airPort utility update the firmware available for both devices on my network 3 June 2016
  1 Airport Express 7.6.7

  2 version of Extreme Base Station Airport unknown as not reported as I expected not die

  After the update successful of the AirPort Express, the update cannot be installed on the Base Station firmware.

  After waiting a while, I tried the update again which also failed to install.

  Current symptoms:

  a. the Base Station is hot indicating energy consumption

  b. No. LED light is during the power on self test or during the race

  c. not discover measure on the WIFI network

  d. is not identified on Ethernet connection without light next to the Ethernet port

  e. DC output is 12V on the connection of the power supply works as expected

  f. cannot perform factory reset using the reset button on the back of the Base Station

  Where other devices working on the same power supply as the Base Station that very sensitive to power outages - these remain functional during the attack of upgrading me to think that he has not lost power while firmware update took place.

  My home network is made entirely of Apple devices - should I worry on the application of the firmware updates in the future.

  It's embarrassing and I now Cat5 running through my house just to maintain services.

  I can't confirm the date of purchase, so I don't know if it is covered by the warranty, however, I'd like to think Apple would cover this.

  What I am doing wrong and y at - it a way to recover the device.

  Help

  We have seen a few posts of users who have had the same problem.

  Unfortunately, not a really nothing you can other your advocate Support of Apple.

  Good luck and hope that you will have this resolved quickly.

• TimeCapsule downgrades WiFi 2.4 GHz after applying the firmware update v7.6.7

  After applying the firmware update v7.6.7 free WiFi to TimeCapsule is now 2.4 Ghz instead of 5 Ghz.

  It was the update of the firmware with certainty that has made this... no doubt about it:

  • My mouse bluetooth interference notice when my MacBook is connected to WiFi 2.4 Ghz;
  • Before the update, everything is OK
  • After updating, my mouse mouse start jittering
  • < alt-click > WiFi icon in the menu bar confirms: the connection is now 2.4 Ghz

  Restart to e TM Mo doesn't change anything.

  In the TC WiFI options tried to put another name to the network successfully, but only 5 GHz can not connect to it: timeout error every time.

  Tried the hard reset of TC and reconfigure the WiFi... the same result, but with a difference:

  • Setting an SSID separated for 5 GHz connection (in the WiFi options) has now created a network I can access.
  • However, this is not the best solution... I don't want 2 SSID.

  It is not the first time Apple breaks things with updates... and I see people move away from Apple to this kind of situations.

  I also had bad experiences with OS updates lately and postpone the as much as possible.

  The problem is that I can't go back... or can I?

  Any help is welcome.

  THX

  The problem is that I can't go back... or can I?

  Of course, you can, but it may or may not help.

  Open AirPort Utility

  Click on the image of the AirPort base station

  Hold down the option key on your Mac while you click on the version number of the firmware

  A drop down menu appears

  Choose the version of the firmware you want to use

• OfficeJet Pro 8620e ADF jam error after firmware update

  After you install the updated firmware from the touch screen of the printer, the printer restarts and now has an error that says "Original is caught in the ADF (ADF).  Open the cover of the ADF, remove and reload the original, then try again. »

  I went through all the steps to clear a jam from the ADF, but the opinion is persistent.  It is not (and was not before the upgrade) in the ADF at all.  Since this coincided with the update of the firmware, my suspiscion is that the firmware has not installed properly or something.  What am I doing here?

  This problem has been resolved using the printer instead of purchase and exchange for another.  I can hardly believe that the cables are working loose within two weeks, she was detained and then broke at the exact time that the firmware update has been completed.  In any case, the problem was solved by replacing the printer.  I don't have any feedback solutions until a month after I did.