FN + F5 Wireless Console to appear in Windows 7

Similar Questions

• CD/DVD drive does not appear in Windows 8

  My CD/DVD drive no longer appears in Windows Explorer in point 8.1 of Windows on my desktop HP Pavilion Slimline 400-034. The disc rotates during startup. I tried the troubleshooting of Microsoft Window 8 with no luck. I would try the HP troubleshooting which requires access BIOS when booting, but by pressing F10 at startup me does not BIOS but Windows load normally. Any suggestions to at least help me get the BIOS?

  Solved! No. thanks to HP. Even if I had never opened the file on my PC and make sure that the cable DVD could not be disconnected, I decided to look for. Much to my surprise, he has been disconnected - but not by me - by a HP technician. I remembered that I had to return the PC to HP to replace the power supply warranty in June 2014. Not only have they not reconnect the cable SATA DVD, they put the cable from the hard drive in the MB connector where the DVD cable was supposed to be. After trial and error and insert the DVD cable in the 3 open SATA connectors with no luck, and finally move the cable from the hard drive to another connector and put the cable DVD where the cable from the hard drive was, the DVD has been recognized by Windows and working correctly. Thanks to HP for the many hours I lost to try to correct their mistake.

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• When I turn on my blue screen laptop appear after windows error recovery windows also appear

  When I turn on my laptop, a blue screen appears after windows error recovery windows appear also... ask in safe mode are normal windows startup?... what I can do... is a problem on my system?... Please help me...

  Hello

  ·         What operating system is installed on the computer?

  ·         What are the error messages that are displayed on the blue screen?

  ·         Did you make any changes before the show?

  In the recovery menu, select Safe mode and check if you can connect?

  You can also try to restore the system in safe mode.

  If you are able to boot to the desktop in safe mode, then I suggest you put the computer to boot in safe mode and check if it helps:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Reference: resolution in Windows 7 stop errors (blue screen)

• HP dv6 ENVY: appearing in Windows 10 constantly up-to-date printer does not install

  MY laptop is a HP ENVY dv6 and I also have a HP Deskjet Ink Advantage 5525.

  Yesterday I updated my laptop to Windows 10, and then suddenly an update appears in Windows Update for the printer.

  It's the update: "Hewlett-Packard - imagery - Null Print - HP Deskjet 5520 series.

  But the update maintains do not install and giving this error "Error 08024200 b ×", and I do not know how to solve the problem. The update appeared only after the upgrade to Windows 10 and I've updated Windows with 10 being automatic, I can't say my laptop to stop trying to install this update.

  Any help would be really appreciated.

  Hi @bleach-eminem,.

  I'd love to help get rid you of the error you see. I suggest you Open the Device Manager and remove the 'unknown' printer you probably see here.

  1. Click on the right arrow next to the following entries to develop and then search for your printer in each list:

• Whenever I try to find new updates for my computer error 80248009 appears under Windows Updates. I have not installed new updates on my computer in a month because of this problem. How should I do so that I can update my computer?

  Whenever I try to find new updates for my computer error 80248009 appears under Windows Updates. I have not installed new updates on my computer in a month because of this problem. How should I do so that I can update my computer?

  Error when you try to use Microsoft Update or Windows Update Web sites to install updates: "0 x 80248009":
  http://support.Microsoft.com/kb/956700

  Quote your full version of Windows (for example, WinXP SP3;) Windows XP 64 - bit SP2; Vista SP1; Vista 64 - bit SP2; Win7; Win7 64 bit) when you post in a forum or a newsgroup. Please do it in your next reply. ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• When I shut down windows end progra - sample appears and windows will not be stopped, unless I click for end of program. Eny one have an idea how to stop this program from running?

  When I shut down windows end progra - sample appears and windows will not be stopped, unless I click for end of program. Eny one have an idea how to stop this program from running?

  Then, you will need to request Support Intel if the drivers you downloaded were appropriate for your hardware and Windows XP.

• My DVD drive does not appear in Windows Explorer

  This morning my computer ran a scan virus and other things, and when this was done, my computer will not respond to any type of CD.  No DVD, CD or even disks with files stored on them.
  When I open windows Explorer, the drive from DVD (e) is not even more appear.  I was wondering how to fix this.

  Hello

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• How can I customize the appearance of Windows 8?

  This video was released on the HP's YouTube channel and thought I'd share it here for those who do not wish to customize the appearance of Windows 8.

  I hope this is useful.

• Combo DVD/CD drive does not appear in Windows Explorer or the Device Manager

  The combo DVD/CD on my laptop drive isn't in Device Manager or Windows Explorer.  The door is not ejected.  You must use a paperclip, poking into the hole to open it.  I also re - it sitting, but it changed nothing.  We had this laptop for 1.5 years and the disk worked great until yesterday when trying to install Starcraft II.  Installation failed and it has messed up also the DVD/CD drive.

  We read some other difficulty advice and tried the upper and lower filters in the registry, but there was no entires of upper and lower filters in the key.

  The specifications of the laptop are:

  HP Pavilion dv7

  Processor Dual-Core Mobile RM-72 2.10 GHz AMD Turion X 2

  4 GB OF RAM

  64-bit Windows Vista

  Hello

  Check with HP Support, their online documentation and drivers, and their known forums
  questions.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• The original appearance for Windows Vista

  I downloaded registry mechanic and some how my original appearance of Windows Vista has disappeared. My appearance now looks like I got Windows 95. I would be very happy if someone could help it. I did everthing I could change. I don't see the original appearance.

  NEVER use Registry cleaners.

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not resolve the problem:

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-desktop-theme

  Read the above about the themes of Vista.

  http://www.WikiHow.com/turn-on-Aero-in-Windows-Vista

  How to turn on Aero in Windows Vista at the link above.

  If you still have problems of re-download drivers graphics:

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• KB3072305 still wants to install after KB3142042 - replaced update appears in Windows Update on WES7 32 bit

  When you perform an installation DVD for WES7, I try to include all the updates that Windows Update would later.  I recently added KB3142042.  There are a large number of updates that are directly or indirectly replaced by this update.  Updates replaced is KB3072305, which now appears in Windows Update as something that must be installed.

  Out of embarrassment, my concern is that the older "allows to correct ' something in a way that breaks or reverses the effect of KB3142042.  My only question: If this update installs, can it somehow 'break' the system in a way that reduced functionality or security?

  The list of the relevant supersedures is KB3142042-> KB3135988-> KB3099862-> KB3072305

  32-bit Windows Embedded Standard 7 (WES7-32).

  Hello

  Try to re-post your query on the MSDN forums , because we have experts working on this type of questions and for you help the better.

  Check out the link:

  https://social.msdn.Microsoft.com/forums/en-us/home

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• Wireless Xbox 360 Controller for Windows all of a sudden not connect into any USB port

  Original title: Wireless Xbox 360 Controller for Windows issue.

  Hi, I bought this back in 2008 and it has been flawless since today... I tried to use it and the controller is unable to connect to the receiver.

  There is no light on the receiver, even when I plug it into a different USB port there is still nothing... I even tried another computer. I assume the receiver is nakered?. Can anyone shed some light on this?

  If the receiver is so broken, can I buy this receiver on its own and that it will be compatible with my wireless controller Xbox 360 instead of having to buy another expensive controller...

  Thank you very much.

  Hello

  I suggest you to post your questions or comments about the Xbox 360 Forums, so that you will be provided with the assistance of your Xbox 360 product.

  Link: http://support.xbox.com/en-US/xbox-360/browse?xr=shellnav

  Hope this information helps you.

• Microsoft Wireless Keyboard 1.1 configure Windows 7

  Hello

  I have the Microsoft Wireless Keyboard 1.1 and Windows 7. At the top of the keyboard, there my documents, my pictures, my music ect. buttons.  These do not work when I press them.  How to connect to my folders on my computer?

  Thank you

  Hello

  ·        What is the model number of the keyboard Microsoft do you use?

  ·        It was working fine with Windows 7 earlier?

  If this isn't the case, you may download the latest version of the software for the keyboard and check if all the keys work fine.

  Follow the link below, fill in the appropriate information and download the software.

  http://www.Microsoft.com/hardware/download/download.aspx?category=MK

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I get my device (WD Passport) appears in Windows 7?

  I have a 1 TB WD Passport to transfer files from Linux (Ubuntu) to Windows 7. For some reason, the drive appears in Ubuntu and Mac computers but does not appear in Windows, the file system is NTFS (yet ironically works only in Unix-based operating systems) and I can't reformat the drive without losing the data on the USB. I also checked the disk management and it does not appear there either. I tried other USB keys and they are automatically detected, as they should be to prove that it is not a problem with the USB port. The light unit of 1 TB and I can hear it turn but nothing is displayed under computers.

  Any suggestions? Otherwise, I'll have to transfer 8 GB at a time to my other USB stick from mac to windows that is simply delayed.

  Thanks for any advice.

  Hello Guy,.

  Thanks for posting your question in the Microsoft Community. We are happy to help you.

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following questions:

  1. Significant changes were made to your computer before this problem?
  2. Have you tried to connect your external hard drive to a different USB port?

  You can try after the methods given and check if this helps solve the problem.

  Method 1:

  Try to run Automated Troubleshooting Services and check if this helps solve the problem.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2:

  You can also check in the device if Manager disk external drive is listed.

  1. Connect the external hard drive to the computer.
  2. To open Device Manager, type devmgmt.msc in the box Start Search and press enter.
  3. Check if the hard drive is listed.
  4. In Device Manager, expand the hard drive listed in the list of devices.
  5. If the hard disk is listed, right click top > click Properties.
  6. In general, under control of device for the message status. After back if there is no error message.

  Method 3:

  You can also try to change the drive letter using the command line and check if you are able to use the external hard drive after that.

  Assign, change, or remove a drive letter

  http://TechNet.Microsoft.com/en-us/library/cc757491 (v = WS.10) .aspx

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

  Thank you.