Folio 9470 m: questions of 9470 m 3 USB HP Folio

Similar Questions

• Folio 9470 m: Folio 9470 m, no USB, Windows 64 bit Pro 8.1

  Since migrated to Windows Pro 8.1 64 bit, USB don't work anymore.

  I have installed all the drivers correctly, but in Device Manager, "xHCI USB" shows a warning. In its properties, I have an error Code 12.

  Thank you.

  Download and run the Intel chipset update utility.

  http://Downloadcenter.Intel.com/Product_Filter.aspx?ProductID=816

  Use the Troubleshooting Wizard in Device Manager to determine where the conflict is,
  and then disable the device in conflict.

  Install the HP Support Assistant, then run Tuneup utility. It should find the driver that is needed and provide a link for you to download from. The following link is directly to the download.

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5275307&swItemId=ob_144416_1&swEnvOid=4158

  Are you aware that there is a version in French of the HP support website consumer?

• Question - the upgrade with 3 USB card and esata

  I have an early 2008 Mac Pro Quad core 2.67 going to have maxed out RAM soon and are planning to get a couple of 2 TB seagates Macgurus. I'm a little embarrassed by my lack of knowledge, but I'll put my questions over there anyway. Last year, I bought a 120 GB ssd card Accelsior PCIe mercury OWC - not being aware of the s and outs of things, but I knew it wasn't a port multiplier with two external esata ports. so my question is this: since I have to live with this card can I connect the esata ports to discs in separate outdoor pens and then through disk utility make a raid 0 set, and what size of disc must be effective for the cost the least?  I intend to get a USB 3.0 also so that I can use this speed also.  My other plans must be a drive of fusion with the ssd 120 on the map of Accelsior with a disk of 1td existing in my drive for the system Bay and replace all small readers of seagate more big HARD drive and I'm wondering if the 2 TB is the largest capacity I can use internally. I am on a very limited budget so that's the reason why I'm thinking hdd and if there is someone with advice on a card USB 3 I would appreciate your comments - in fact, I would be happy to comment on everything I mentioned, I'm a little out of the loop on the evolution in recent years. It is possible to configure a raid with two disks of two PPI crd esata ports would there be an advantage with drives of 2 TB or 1 TB disks would work as well for raid 0. Do I intend to put in storage for Time Machine with the USB 3 map, and what size disc would be appropriate for Time Machine? I'm not lazy and waiting for someone to find out - I did weeks of research to get to this point and I just need a little advice. I'm just going through what I know and what I can afford, but maybe I'm missing another solution to try to get a little more speed and back up storage for my photoshop files.

  I do only cc2015 Photoshop, Lightroom and On1software version 10.1 using OS X El Capitan and a cg 276 Eizo monitors more a second older Eizo. My usb ports 2 are all used and I rarely use a firewire port. Thanks in advance to all those who have advice. This is the first time that I have not posted anything on this forum

  Time machine is a USB 2 connection. No real reason for a USB 3 connection.

  There is no RAID in disk utility in El Capitan. Apple dropped the disc utility in El Capitan. However, you can still the Terminal commands to configure RAID.

  https://www.reddit.com/r/OSX/comments/3d7aw2/does_el_capitan_disk_utility_suppor t_raid.

  You should be able to create a set with eSata RAID

  Here is a map of the BSE 3 compatible with El Capitan.

  http://www.sonnettech.com/product/allegrousb3pcie4port.html

  USB 3.0 Mac Pro 2008 El Capitan

  Make sure that the card said it works with El Capitan. Some cards USB 3 is no longer with El Capitan as the CalDiget of first generation card.

  Internally the Mac can also use large HD depending on availability. However, there is a bug that first appeared in 10.8.4 and has not yet been set. To format a plu 2.2 to internal HD:

  -Use a disk utility of all Mac OS X older, including the 10.6 DVD (if your Mac can boot from it) or any of the installation DVD player or boost saved work.

  -Another solution is to move this drive in an external case and delete it there (assuming your case is modern enough to deal with readers more than 2.2 to.

  In addition,

  To sled mounting internal:

  The penetration of the screw depth for 'down-screw mount adjacent to the platters' on some readers from over 3 TB have been shortened. This may mean that the live sled down until they adjust and begin to compress the washers on the sled. If this is the case, your drive will not rest flat on the sled and do not breed with the connector backplane without additional adjustment.

• Question about an external Bluetooth USB device

  Hi all!

  I would like to ask help from anyone on this forum for this question. Recently, I used an external Bluetooth USB device, the product name is IVT Bluesoleil, is this product safe for my Toshiba laptop?

  Should be no problem.

• Sansa Clip + Question of burden (with mini USB cell phone charger)

  I have a few questions about the issue of workload:

  • is it acceptable to fresh clip + use the charger of mobile phone with mini USB socket (5v ~ 700mA), as I know, USB 2.0 specification is 5v ~ 500mA?
  • Sansa is equipped with a circuit to handle the charging process, for example the the blackout when the battery is fully charged?
  • After that several hours connected to the computer, the turn display self... is this normal? (so I have to press a button to see the screen saver and check the State of charge)

  Thanks for the answer of my question... hehhe

  You can use any charger, but be sure that it is 5V and not higher than (above will FRY your Clip).  Around 350 my and especially (even if some 500 my and above is best) is very well - the Clip will use the amperage he needs.

  Yep, you can disable the data pins and everything should be ok.  Just be sure you know what you're doing on the pins.  Many people say to be able to arrive at the same end simply by inserting the USB cable into the computer, not completely or by covering the data pins.  In addition, you can buy USB charge cables only - I have a couple of people.

  Note that when you connect to your computer, you can still read the Clip files, via the computer itself (not the music) and media playing software that is pointed and play the songs on the Clip.

• Installation question on Satellite M30 PSM30E USB mass storage device

  Hi people,

  I get an error message when I try to install new hardware on my laptop. Windows XP is trying to find the drivers and then comes up with the following error after a few minutes. The software starts to install but then comes with the following text:

  "There was a problem installing this device:"

  USB mass storage device
  An error occurred during the installation of the device
  These data are incorrect

  What happened with a USB card reader and my mobile. Once I have the error box I get a message saying that the device will not work properly?

  Anyone has any ideas at all?

  See you soon

  Hello

  What series of notebook or laptop model do you have?
  Could you please put the whole number? It would be very useful for further study.

  All the installation driver Toshiba must be made in the right order.
  In most cases, you would find a txt file of installation instruction on the Toshiba driver page.
  You must follow these instructions to ensure that all drivers would be executed correctly.

  Concerning

• Questions on Satellite A100-787 - USB over current on HC/Port USB

  The next day, when I turn on the laptop
  TOSHIBA Satellite A100-787
  I saw the error message: -.

  ERROR

  0701: USB over current ON HC/Port - Bus: 00 H dev. : 1DH Fun: 01 H / Port: 00 H

  ERROR

  0701: USB over current ON HC/Port - Bus: 00 H dev. : 1DH Fun: 01 H / Port: 00 H

  ERROR

  0701: USB over current ON HC/Port - Bus: 00 H dev. : 1DH Fun: 01 H / Port: 00 H

  It me not allow Windows to connect. Hope someone has a solution for this error.

  Hello

  Believe me; I see this error message for the first time.
  This certainly isn't a simple error due to software problem, but I think there might be something wrong with the hardware.

  But before you contact the ASP in your country, you should check this:

  If you are not able to boot in windows, so why you n t try to reinstall the operating system?
  Try to boot from the Toshiba Recovery CD and check if it of possible to reinstall Windows.
  In addition I recommend access to the BIOS and try to pass the default BIOS settings.

• Question of the digital input USB-6009

  Hello

  I use USB-6009. I have problem in Input.I digital did not connect anything on all channels. But all of the DI/O channels generate 5 volts. And I tested the DI/operating system in the Test Panel also. All digital inputs are high. How I use it? Please suggest me the solution.

  You're the one who said it was generating 5V. And I said that a fine should be detected as a logic one. Connect a gnd input.

  When it starts, all of the default value of I/O at the entrances.

• Question: How can I format USB stick FAT 32.

  Thanks a lot... problem solved!

  "Disk Management" allows you to delete the existing partition and create a new partition and format FAT32 or use one of the 2 utilities listed below:

  -Partition management utilities-

  Partition Wizard Home Edition:
  http://www.partitionwizard.com/free-partition-manager.html
  Note: There is also a CD bootable or versions of the bootable Flash drive:
  CD: http://www.partitionwizard.com/partition-wizard-bootable-cd.html
  Flash player: http://www.partitionwizard.com/bootable-flash-drive.html
  Among the features and functions: create partition, Delete partition, format partition,.
  A partition resize, move partitions, Partition recovery after an accidental deletion,
  Convert the partition, partition Explore, Hide partition,
  Change the drive letter, a partition active Set, Explorer (content display) of the partition.
  Note: To complete any task use the "Pending Operations" box at the bottom left.

  Alternative to Partition Wizard (a bit easier to use, but Partition Wizard and EASUS have almost identical user interfaces)
  EASEUS Partition Master Home Edition (free):
  http://www.partition-tool.com/
  Partition software ALL-IN-ONE and the most convenient hard disk partition manager Kit
  Includes Partition Manager, Disk & Partition copy Wizard and Partition MBR and GUID partition GPT disk recovery Wizard (table) on Windows 2000, XP, Vista, Windows 7 and Windows Server 2000/2003/2008 (32-bit and 64-bit).
  It allows users to resize/move Partition, drive system extend, copy Disk & Partition, Partition merge, Split Partition, redistribute free space, convert dynamic disk, Partition Recovery and much more.

  J W Stuart: http://www.pagestart.com

• so many questions: no sound, cannot use USB and dongle...

  I have a toshiba satellite l505d-gs6000... I have installed the latest updates for my computer stop for the night he opened in the morning and I have no sound, unable to use USB and dongle... I restored an hour earlier and who fixed it, I have re installed windows os and it does not solve it... the drivers on my sound it's updated but also when I click on its screen it says: no audio output device is installed:

  Hello Jason, I've done a little reading on your laptop model, it seems, there is a hardware problem with this range of laptop, which causes the USB and sound to fail. There is no known for this hotfix.

  Check out this thread of Toshiba... http://forums.Toshiba.com/T5/audio-sound/no-sound-USB-on-satellite-L505D-gs6000/TD-p/172564/page/8 
  You will need to contact Toshiba customer service if your laptop is under warranty.
  Find a Toshiba Service Center

• Really simple (hopefully) question about GPIB-USB-HS

  I tried to reconnect a GPIB-USB-HS to a network through a PC HP on shelf Analyzer. Before removing the GPIB-USB-HS system about a week or two ago, Network Analyzer (a vintage 1989 HP 8720 vector Network Analyzer) had worked well with the GPIB unit. Now that I reconnected the GPIB device to network monitor, measurement and automation seems not be able to detect the Network Analyzer.

  My question is: if my GPIB-USB-HS appear in measurement and automation, and it passes the NOR-488. 2 troubleshooting of HW and SW utility test, it would be safe for me to assume that whatever connection problems I have with the Analyzer network, rather than with the GPIB-USB-HS itself?

  Thank you

  Armando83

  I finally got the connection working again. I just had to tighten the screws on the GPIB-USB-HS to make sure it's a good connection to the Network Analyzer so that it can work.

  Thanks again for your help, Dennis.

• Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Disconnect all USB storage.

  Run this tool by do right click and choose 'run as administrator '.

  Of course, all first extract it:

  http://www.Uwe-Sieber.de/files/drivecleanup.zip

  If your XP is 32 bits, use the Win32 folder.

  Reset.

  If you still can't find the drive, assign it a drive letter in disk management.

• Can you iPhone 7 connect to USB headset

  Hello!

  I am the owner reasonably high-end headphones Sennheiser Momentum M2 wireless. It connects to my iPhone via bluetooth or using removable 3.5 mm plug + cable. When I use it with my MacBook, I connect USB cable to the USB port on my MacBook Pro to listen to the audio quality (M2 these headphones have a micro-USB connector).

  It made me wonder if I could connect my M2 headset with my iPhone 7 using a micro-USB male for cable male-lightning and listen to music when, for example, the battery is dead, or when I want the best quality audio.

  Thanks in advance for taking the time to answer my question.

  No, the usb headset is cards usb audio full blown for computers that require device drivers work

• U840-111 satellite shows an error at startup

  Basically, I was using my laptop computer and suddenly, he crashed and grew the "blue screen of death" I restarted and let the restore program starting run.

  After that he had finished he kept makes this message 'there is a problem because of evil to disconnect a device as an external hard drive. If this message persists, contact your hardware vendor... I tried to reboot several times but nothing helped. I think I might need to restart using a boot disk (which is a problem that the laptop didn't come with an os disc) or even take it to be repaired.

  Any advice.

  Stand by.
  According to specification your U840-111 was delivered with Windows 7 Home Premium 64-bit pre-installed. Original recovery image is saved on the HARD drive and it is strongly recommended, and described in the user s manuals document the laptop owner should create recovery media that can be used if the disk HARD recovery doesn't work.

  For notebooks without optical drive, it is clearly described that recovery media bootable USB can be created using preinstalled Toshiba recovery media creator tool. So first question: you created this bootable USB key?
  >... and let the start of the restoration program managed
  Do you mean that you have started the HARD recovery disk image installation?
  > I use a USB boot drive.
  Does that mean exactly?

• Satellite 1400-553; Is it possible to USB 2.0

  Hello

  I have a question:
  My PC using the USB 1.0 port. It is possible to use 2.0?
  Ther's some update to do?

  Thank you!
  Luigi

  The pc's Toshiba: Satellite 1400-553 s

  You are right.
  The Satellite 1400-553 s (PS140X) seems to support the USB 1.1 version

  But it also seems that the Satellite 1400-553 s supports a PCMCIA slot.
  You can use the PCMCIA (Cardbus 32-bit) and PC - card 16 - bit cards.
  There should be a space for 2 cards PCMCIA Type II or 1 Type III card

  To my knowledge, there are some PCMCIA cards with USB 2.0 ports.
  Therefore, it would be possible to use this card to get the USB 2.0 capacity