from the hypervisor can ping of the gw & dns servers

Similar Questions

• Install the new - cannot ping configured gateway or DNS servers

  Hi all

  My old VMWare ESXi 3.5 OS got corrupted I did a fresh install of VMWare ESXi 4. It installed ok and I was able to configure everything successfully, but when I run the network test it is impossible to ping anything whatsoever, but it's own IP address.

  I have another machine on the same subnet with the same exact configuration (except for the hostname and IP static) settings and it works properly without any problem.

  I already checked the cable at the back and the green light is on and the flashing. I tried to restart the machine after having placed in the configuration information and settings remained at what I put in, but I still get the same result. The network test is a failure.

  Does anyone have any suggestions as to what could be the cause of this?

  How do you have installed and configured network adapters?  Have you tried swapping the cables between network cards?

  Also, do you have the trunks VLAN configured on the switch?  It is possible, that you must specify a trunk VLAN for the management network to do the work.  That would probably have already been configured on your host 3.5 but is not automatically detected and added.

• Main server cannot ping the server 2 to another location, but the 2nd Server can ping the backend

  I have 3 servers: server and 2 servers to files in another country.

  My main server can only ping the 2nd file server.

  But both of our servers in 2 files from another country can ping on the principal server.

  In short, I can not away to the first file server.

  The settings on both servers of files are the same. And I don't have access to the 2nd file server issues using the main server.

  If someone has the patience to help me understand the question?

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• How to display /etc/resolv.conf and other files from the remote host to the vMA host ESX4i

  Hi all;

  I'm new at VMAs, I put it in place and adds 5 Server esxi 4 and I can list the fines using vifp lists broadcast and works, very well but my problem is I want to interrogate the remote servers for this vMA host for example I need to check the contents of these files

  cat /etc/resolv.conf

  cat/etc/sysconfig/clock

  tail/var/log/vmkernel

  Discovered the following

  esxcfg-firewall - q and esxcfg-vswif - l

  Can someone please help me on how to run these commands or another way on how to get this information above hosts and ESXi 4. I checked the forum, but I don't see anything similair nature! now, either I'm stupid full because it's as simple as drinking water and so no one asked or I am just lucky to ask the right question, so be it, I appreciate your time and effort

  Thanks in advance

  Esxlinux

  So its worth your time through the vMA documentation to understand how to manage your hosts and it's main use case. The operations that you are trying to accomplish cannot be done using vMA... at least in the way that you are hoping for.

  See my vMA article and some of the getting started guides.

  cat /etc/resolv.conf

  You will want to use esxcfg-dns to list the configured DNS servers

  cat/etc/sysconfig/clock

  This file does not yet exist on ESXi, if you try to set the time on ESXi host, you should use NTP and it is also important to note that single ESXi uses UTC and no other options are available.

  tail/var/log/vmkernel

  If you need to display the host logs, consider using vi logger on vMA OR configure syslog on your host to send to the centralized syslog server

  Regarding the last two commands, they do not apply to an ESXi host and therefore these commands are not available.

  There are certainly differences between ESX and ESXi, understand the differences and orders to ask for certain pieces of information is very important. vMA can help with this, but you must understand the use case of vMA and what tools are at your disposal. The best way to start is to take a look at the documentation, to jump it and try to jump in, will just be confusing.

  Good luck

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• Cannot access a Web site, but can ping IP addresses on the internet

  -With the help of Vista SP2 64-bit on laptop faulty.

  -Number of computers on the same network have access to the internet.

  -Tried several network interfaces on this laptop, but no luck for access to the network, wired or wireless

  -From this notebook, I can ping addresses Internet IP so the problem seems to be the side DNS.

  -Flushing DNS cache and reset the network interface.

  -Rebooted several times.

  What did I miss?

  Thanks in advance

  Hey easternguy,.

  Check if you can test the Web site by name.

  To do this:

  a. Click Start and type cmd.

  b. press ENTER.

  c. type the following command:

  ping hostname

  Ping uses name resolution to resolve a computer by IP address name. Therefore, if you successfully ping the IP address but you cannot ping a computer name, there is a problem with host name resolution, and no network connectivity.

  Case 1: If you can not ping the Web site using its address, follow these steps.

  In this case, try changing your host file.

  In the C:\Windows\System32\Drivers\etc Hosts files may be damaged or corrupted.

  Review the contents of your HOSTS file and compare it to the screenshot below. There is no need to worry about any line that starts with a # is ignored by Windows. In addition, the line "127.0.0.1 localhost" can be ignored without risk, because it is a standard input.

  

  Everything that appears in your HOSTS file without a # earlier this year, aside from the "127.0.0.1 localhost" line, should be regarded with suspicion when we try to diagnose the cause of the problem. The fastest way to test the involvement of HOSTS file is to just rename the host file. By changing the name of the HOSTS file, prevent us Internet Explorer to use it and so all problems caused by the file.

  Case 2:

  If you can ping external websites by IP address and name, but can't browse the web, probably your browser is misconfigured.

  Check that you do not have an incorrect Proxy Server affected necessary or not.

  For Internet Explorer, follow these steps.

  a. open Internet Explorer.

  b. go to Tools / Internet Options.

  c. click on the Connections tab.

  d. click the LAN Settings button.

  "e. uncheck both" "automatically detect settings" and "use a proxy server for your LAN '.

  This should be it.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Registry files have been deleted via a Norton 360 3.0 registry clean up - can't get an ip address from the router

  I'm running Vista Ultimate, -connection (Ethernet) with Verizon FIOS I ran a Norton registry clean and foolishly trust what he says to remove.

  At first, all of my USB cards have been screwed up (noted in the Device Manager with exclamation next to each one points)
  I did a system restore and that corrects this problem, but now I'm having a problem with my network card.
  , All diagnostic tests, etc. show that the material is very good. My router is also fine the problem is that windows can't get an IP address from the router and then assigns his own
  (a # 169 instead of a # 192)
  In the network connection properties, it says that the device is functioning correctly, and the driver is up-to-date.
  'Connection speed' tab: a window of diagnosstics is: I ran testto test adapters connect to connect to the network.
  Results: connection Test
  Test details:

  I have "this card is configured to obtain an IP address automatically. No DHCP server is present on the network. Windows selected an IP address by using the alternative private IP addressing. »

  X "Ping 0.0.0.0 Gateway: failure.
  !  "No DNS server is available for this connection.
  ! "No WINS server is available for this computer.
  X "Ping 0.0.0.0 network: failure.
  ------------------- -------------------------------------------------------------------------------------------------------------
  In this same window of diagnostics under the "LinksTab".
  Link current test status: (what is determine the current connection speed of the adapter and link partner)
  Results:
  ! The adapter is configured to negotiate the speed with the link partner, but 1000 Mbps was chosen as one of the possible speeds.

  The best link options-results of the speed test:
  ! Could not detect way reliable speed and duplex settings. Possible speed/duplex settings are 100 Mbps Full Duplex and Half Duplex 100.
  (Note that these link tests are online and I can't online)

  Also in the Diagnostics window-under the 'Cable' link cable - past-polarity is normal.
  Depending on the tab is the Hardware tab
  Hardware diagnostics check for I/O conflicts...
  Results: all the tests:
  EEPROM test
  FIFO test
  Test register
  Interruption of the tests
  Loopback test

  I also went in the prompt type in IPCONFIG... c which shows:
  Ethernet connection to the Local network card:
  ConnectionSpecific DNS suffix: (it's completely empty here)
  Link-local IPv6 address: fe80::bda9:951 d: 619f:a0dc 9%
  Autoconfiguration IPv4 address: 169.254.160.220
  Subnet mask: 255.255.0.0
  Default Gateway: 0.0.0.0

  I also have a sort of ping command here-cant remember the command, but the results were in the CBS... I didn't know how to reach. He however escape from something on the registry files.

  I went throughD-Link Tech router (router) support is good, Fios Tech support everything set up right, - Norton support(Norton denies that the files were not to be touched-although their report shows these registry files were deleted)-Dell Tech support because my warranty missed 3 weeks ago - although I still have the "your Tech Support team until 2013 - which is valid only if you have a hardware warranty-made no sense sold me the car without. the engine - directed the FTC to bring a complaint about it - after I get this fixed number.

  I hope someone can help... by the way I get perfectly in line with my laptop - I know this isn't my router. I'm sure it's due to some registry files being moved-(j'ai eu deles de messages d'erreur indiquant que les fichiers de Registre ont été endommagées ou manquantes) what do I do now? No system restore to restore this part of the register - I also installed the drivers from the dell drivers and Utilities disc - but maybe I've done that correctly? I put the disc - extract files-(he says they have been unpacked) was a new step for me to do after that? Help, please!
  Thank you!

  Hello
   
  We recommend that you install the router (see its manual) and the pilot of NIC once more and check the difference. In the first post, you mentioned that you decompressed or extracted files. Once the files are extracted, you will be asked to install the driver. However if you do not receive any prompts for the driver, then you will need to locate the destination folder where the files are checked to find the configuration file.
  
  Open the destination folder where the files are extracted and run the Setup file to complete the installation.
   
  To download and install the latest network card driver, visit the site Web of the manufacturer of the device or system.
   
  For more information on downloading and installing the drivers, visit this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/the-hunt-for-drivers-how-to-find-Windows-Vista-drivers-for-all-your-hardware
   
  I hope this helps.
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Vista: Gets the IP address can ping by FQDN and IP address but impossible to surf Web sites.

  Vista:

  Gets the IP address can ping websites by FQDN and IP address but impossible to surf the internet.
  Default gateway is correct

  Same result using two network adapters.

  Norton internet 2010 (same result enabled / disabled)
  WinsockFix (no joy)

  Hi Bigfeeet,

  A. what browser do you use?

  Are b. from when you facing this problem?

  C. you get any error message?

  Have d. you tried with another browser?

  If you are using internet explorer, I recommend you follow the steps in the article below and post back the result.

  http://support.Microsoft.com/kb/956196

  Bindu S - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Can Ping but not connect via Remote Desktop - how to change the settings of the outside LAN adapter

  I have a Windows Server 2012 machine connected to a Windows 7 Pro machine via a switch.

  Internet is shared on the Windows Server and the port sharing network has a static ip address. Similarly, the port connected to the Windows 7 Pro has a static ip address. I was able to desktop Windows 7 remotely from the server without any problem until very recently.

  Recently, I had to change some properties of the LAN on the machines and I was changing the gateway by default for the Windows 7 Pro, when I was hunting from my remote desktop session and I was not able to reconnect since. I don't know if I accidentally blew the subnet or the default gateway, but I know for sure that I do not touch the part of the parameters ip address.

  In addition, I can't ping the server computer but I am not able to connect via RDP. Please suggest any possible causes and solutions for this case. Both computers are remote and I can connect via the internet to the server computer.

  As my title suggests, I'm trying to find out if there is a way to reset the settings of the adapter LAN from Windows 7 to my server and proceed from that.

  Please let me know if you need more information.

  Thank you.

  RAM.

  Hi Ram,

  Please contact Microsoft Community.

  Problems with Windows Server 2012 are supported in the TechNet Forums. I suggest you send the request in Windows Server 2012 general Forums TechNet.
  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?Forum=winserver8gen

  Hope this information helps.

• Cannot ping inside the ASA from the inside interface

  Don't know what I did wrong... appreciate any help

  Here is the page layout

  laptop--> cisco 3750 switch--> ASA5505 firewall--> future VPN tunnel

  Laptop, switch interface VLAN and inside the ASA are all in the same subnet

  Switch and ASA have all interfaces local network VIRTUAL 52 (the subnet in question), except for the external interface

  -----------------

  This is the problem

  laptop getting ip addressing and def GW via DHCP from the firewall

  switch and FW can ping each other without problem

  FW can't ping, still gets the DHCP scope.

  Thank you

  Dave

  Hello

  How did you setup?

  The laptop is connected to a port of the 3750 (VLAN 52).

  The connection between the 3750 and the SAA is a chest or a link L3?

  If the 3750 has a SVI belonging to VLAN52, you can ping from the correct PC? As well as the ASA?

  Federico.

• Virtual machines can ping throughout the network, but can't ping in them.

  More in detail, we run ESXi 5.1 on our host servers. We then run a client vSphere on one of our client machines that can reach the host by a Cisco 3750 switch servers. So it is, machine client, Cisco switch, then the host servers. The server host has 2 network cards going to the switch. NIC0 goes to a trunk port, and NIC1 goes to an access port. In vSphere, we have created a virtual switch that has two physical network interface cards activated. For our management network, the VMKernel port, VLAN ID All we (4095), then we have NIC0 as the active map. Then we have a "Server" network, the Virtual Machine port group, with VLAN ID 30 (our vlan internal) with NIC1 as the active map. Once we have this, we can ping from our virtual servers to our default gateway, then anywhere else in the network, but nothing can ping the virtual machines. We tried to watch a traceroute to the VM, but all it shows is, VM NIC, default gateway, and then destination... Ask for more information if you need.

  Thank you

  Tim.

  Hi and welcome to communities,

  What guest operating system are your current virtual machines to run? If it is windows server, it is a chance network discovery is simply disabled. This will diminish the ICMP packets and you may not their ping.

  If the port of 3750 for NIC1 is configured as VLAN ID 30 trunk.

  Your Portgroup is configured with VLAN ID 30.

  Inside the guest virtual machines you did not indicate any configuration of VLAN, right?

  Tim

• Guest OS using NAT and host wireless can ping Google but can't surf the net

  Hi all.

  I just installed 'Vmware Workstation ACE Edition' Version: 6.0.0 build-45731

  I then installed a new virtual machine Windows XP SP2 home edition.

  My host is a business of W7, browse the internet using a wireless network card. (I currently don't have a way to have the physical NIC connected to it).

  My conf wireless host is:

  LAN wireless adapter wireless network connection:

  The connection-specific DNS suffix. :

  ... Description: Connection network Intel (r) PRO / Wireless 3945ABG

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.33 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Thursday, December 2, 2010 10:50

  Lease expires...: Sunday, December 5, 2010 10:49:59

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  The goal is simple: be able to surf the web with my guest OS (Windows XP Home edition).

  I first tried to bridge with VMnet0 = > KO (no ping, no navigation)

  I then tried NAT which is by default bound to VMnet08 = > always KO but:

  -I can ping google.com:

  Ping google.com http://173.194.36.104 with 32 bytes of data:

  Reply from 173.194.36.104: bytes = 32 time = 765ms TTL = 128

  -I can not always surfing the net

  When you activate NAT on the guest operating system the ipconfig gives the following:

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : localdomain

  ... The IP address: 192.168.31.128

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. : 192.168.31.2.

  I do not have an anti virus installed on the client

  I tried to disable windows firewall with no luck

  I tried telnet google.com port 80 = > KO

  C:\ > telnet google.com 80

  Login to google.com... Could not open connection to the host, on port 80: Co

  nnect failed

  Any help, tracks, ideas, would be greatly appreciated.

  Thanks in advance

  Michael

  Just an info, Windows 7 is not a host VMware Ace/Workstation 6 operating system.  Also why do you install 6.0.0 vs install 6.0.5?

  Have you tried to manually set DNS servers to no known public IP address just leave it to the private IP address that you have shown by default?

  Give a try:

  OpenDNS

  208.67.222.222

  208.67.220.220

  Or

  Google Public DNS

  8.8.8.8

  8.8.4.4

• Can ping on iSCSI lan but not on the production LAN

  I want to test if I ping my gateway, but I can't vmkping she or any host on the local network. But ping my works of san.

  They are on a different LAN. How can I say vmkping to send a ping on the other LAN?

  Thank you

  Hello

  vmkping should be used only to test connectivity between the ESX hosts to check they could run HA and DRS feature.

  It is for this purpose by default behaivior.

  I hope this helps a little.

  Greetings from the Germany. (CET)

• Can I recover my phone numbers of my Iphone 4 from the Cloud

  Can I recover my phone numbers of my Iphone 4 from the Cloud?

  Do you mean your contacts?

  Go to icloud.com and see if your contacts are there.  If so, you can recover.

• IMAP is not supposed to retrieve emails from the server only? In my case, all mails are downloaded to my mac and I can see the offline!

  IMAP is not supposed to retrieve emails from the server only? In my case, all mails are downloaded to my mac and I can see the offline!

  His grip on my mac space, even if I'm using the same settings for my Iphone email are not downloaded to the phone and its not not using any space!

  It is often possible to access the same account using IMAP or POP.

  Make sure that your settings are correct. The account type is on the first part of the account preferences.

• My App Store icon has disappeared from the screen of my iPhone5s. How can I gt it back?

  My App Store icon has disappeared from the screen of my iPhone5s. How can I find?

  Check: Settings - general - Restrictions - installation Apps =?