Good symbol of CMYK color on white but not Black?

Similar Questions

• HP Officejet 6700 Premium: Officejet 6700 premium prints in color but not black

  Hello, I had this printer new and used for 6 months, worked perfectly.  We moved and he was sitting in the box for the last 16 months.  I have just connected printer to the top and she supposed to replace the black print cartridge, so I did.  He also mentioned that the yellow was low.  I printed a test page and it does not print in blue and indicates the Microsoft Test Page.  I cleaned the print heads and I have replaced the yellow cartridge.  It took all three cycles of cleaning, but at least now, the ink test page shows all the color ink, but not black levels.  I ran the print heads clean again three times, no change.  When I put in place, reports, and report printing quality, I get everything except black output.  I replaced the black cartridge twice with no change...

  Any thoughts would be great.  Thank you!

  Thanks for the suggestions to Bob.  I've already tried one.  For cleaning of the printheads, I went on this link and follow in his footsteps.  When I got to the printhead out, I had a syringe and pushed water soapy warm through to the stream of print heads has been good.  I then ran the clean hot water through out the SOAP.  Then I used compressed air to dry the printhead.  I have no ink needed to fill the resovoirs, I so back up the device and installed the ink cartridges.  It took the printer a few power cycles to start working normally.  I also ran the printhead, clean once more.

  The printer works like a charm again!  Thanks for your suggestions.

  https://www.YouTube.com/watch?v=u4CSzF7Wjxs

• My kodak 5100 print part of color but not black

  My printer does not print the part of the text in black. Part of it prints but not all. The part of color is very well

  Hi marlaheaston,

  1. you remember to make changes to the computer, after which the issue started?

  2. have you checked if the cartridge is empty?

  I suggest to try the steps from the link to the following article and check to see if it helps:

  Printer in Windows problems

  I hope this helps.

• The bar color on most, but not all, https sites is blue and not green. This means that they are not secure after all?

  Until recently the small color bar next to the address in each open tab was green for https sites and clear for open sites. The color for most sites https including my Bank is now blue. Some are still green, but most is in blue. Does this mean that sites are be pirated? Not sure? or something else?

  N ° which are the only certificates that are validated in different ways.

  Green means 'Extended Validation SSL certificate' and blue means a 'domain SSL certificate.

  See:

  • https://wiki.Mozilla.org/ca:glossary
  • https://support.Mozilla.com/kb/site+identity+button

• HP 6500 prints of color but not black

  
  

  This is most likely a print head problem. The print head filter ink and put it on paper. If the cartridge has been replaced, I think he'll be the printhead to the cause of the problem.

  I would try an alignment. If this fails, it is the print head. If he succeeds, he can solve the problem.

  Replace a print head will be around $ 50. Most clients prefer to buy another printer. With the printer being 4 years and more under warranty, it would be at your expense. I suggest you call our technical support. We have available updates that are already in promotion for customers with printers with us.

  1-800-474-6836

  When a solution is found, please indicate the position that solves your problem.

  If I have solved your problem, please do not hesitate to provide laurels and make sure that you mark this thread as provided solution!
  Although I work for HP, my messages and responses are my own opinion and not of HP

• OfficeJet Pro 8600 N911a: Can print / copy in colour, but not black

  Last night, tried to make a copy of the Officejet directly black and got a page of black streaks almost completely dark.  Tried to copy the same document in color and got a nice copy.

  Today, I tried scanning a document from hp on my computer software.  Got the same streaks.  Scanned in color and got a good clear scan.

  It may be dirt on the glass which would affect color and black too, right?

  Grayscale printing is fine.

  How can I solve the problem?

  No worries on forget everything shuts off and turns back on.

  I saw the power of the printer and the new solve a lot of problems, but it's the first time I've seen do so solve the problem with black streaks.

  One thing that I would check if it happens again is to make sure that the printer is plugged directly into a wall outlet, not a surge protector. Copy and scan functions can behave a bit strange if the printer does not have enough power.

  I'm glad that you all fixed. If you need anything else please let me know, otherwise have a great day!

  If this solves your problem, then please help others find this post by clicking on accept as Solution on my post.

  If you appreciate my help, so please let others know by clicking on the icon below my post thumbs up.

• change my text color to white

  I have change my my color of white text and black background

  and now my text not displayed all the other colours seem to be working please help

  I was afraid that you would have done it.

  Please change back to white.

  If you want a black background, just draw a big rectangle and fill it with black.

• Photosmart Premium C309g - print in color, not black

  I have a Photosmart Premium C309g which, until a day or two before, worked very well. Black ink does not work.

  I tried already. .

  • Change both black cartridges (regular and photo)
  • Cleaning
  • Alignment (when I try to align printer says "Alignment failed."

  Print fine - but not black color.

  Problem happens both when printing from a computer, as well as select black copy then copy - gives only a blank page.

  Printer on a network and is used for both Mac and Windows 7.

  You can give me any help would be appreciated.

  Thank you.

  Try the suggestion in this thread to soak the printhead.

• HP Photosmart 3310 all-in-one does not print print test page doe but doesn't show is not black

  I have a printer all-in-one HP Photosmart 3310 that does not correctly print a test page (print color but not black) and does not print a WORD document from my computer.  The color that should be black in the test page after CLEANING print head appears as a Purple-ish Brown, although after the PRINTER SNAP the printed page shows a short BLACK bar to the left of the five longer bars in FIVE COLORS.  The computer in use is a HP Pavilion dv7 with processor Intel Core i7-3610QM, 2.3 GHz, Ram 8. 0 GB (7.9 GB available), 64-bit and Win 7 Home Premium OS, SP1.

  After having downloaded HP Print and Scan doctor, we arrived, after a series of steps to "If the cartridges have been refilled and none is empty, try calibration of color": Open HP Solution Center (start, all programs, HP, HP Solution Center), then click on settings, settings, printer Toolbox, printing on the tab device Services, click on color to calibrate.  This procedure is NOT AVAILABLE, however, because I can't find the HP Solution Center.

  What should I try to fix this problem?  Please be specific - and please also include any recommendations for a remedy that is exactly what happens if something must be verified or checked before trying the recommended remedy.

  Since the last post, I repeated the test several in Solutions of HP.  Whenever I have repeated the procedure clean print heads, improve the quality of printing in black ink a little bit.  After several passages of this test, maybe 5 or 6 more and separated by some rest of the time, the quality of printing in black ink has reached the State that I consider finally acceptable.

  A variable that I can't rule out or rule through all this is the temperature and the humidity.  It has been a winter VERY exceptionally difficult, with a lot more than zero days and subzero temperatures.  And with that comes challenges with the indoor humidity (even if we have the whole House humidification).

  In all cases, the printer now works without problem.  And I'll post that I accept the solution most recently proposed by the HP Forum.

• My HP photosmart 6510e all-in-one scanning pictures in black and white but the docs are still in color.

  Scan pictures into my a6683w HP Vista in black and white, but the documents still scan in color.

  Hello there ingridt, welcome to the Forums!

  I noticed your post on the scans of your Photosmart 6510, scan to your system from Vista in black and white. I want to offer my suggestions to you to see if they can help you with this.

  First of all, try to launch the HP print and Scan Doctor who is used to fix the printing and scanning problems. You choose the option "Scanning" when the tool is run. It will inform you if the software is completely installed, or if there is a problem, it can not correct. If it detects an error and shows you a red 'X', I suggest then uninstall and reinstall.

  Here are some links to help with uninstalling and reinstalling if you happen to do these steps.

  1. uninstalling the printer software

  2. restart your PC

  3 reinstall: Photosmart HP 6510 e-All-in-One Printer - B211a

  Try a scan now and let me know how make you out!

  Good luck!

• scanning black and white but colored wrong scan OK

  OfficeJet Pro 8600 more

  Copies n & B Standalone are very low. Color copies are excellent. B & W scans on my computer appear almost not. Color scans are excellent.

  Any ideas?

  Travis_C wrote:
  

  Hello jkaminky

  When you press on copy and go to the settings adjust you the lighter/Darker? Also are you running the latest firmware? What operating system do you use?

  Travis,

  Yes, the printer was up to date in its fireware. I am running Win 7 Pro (64), but the problem resurfaced surface during a copy operation only one position from the table of the printer. I advanced the lighter/Darker the maximum setting and it helped, but not as 'Normal' of origin. If I chose a copy in color at the keyboard, a B & W document came out excellent. My troubleshooting reveled that the problem wasn't actually in the scaning aspects of printing of the operation.

  I made a number of steps with scaning of troubleshooting. I carried out all them from the table and sent output to a flash drive on the printer. I wanted to keep the remote computer. Even from the keyboard on the preview screen, I could see the very light scans of B & W, I did a number of quality adjustments to their levels of maxminum with an improvement, but not quite to its previous level of quality.

  I was ready to leave when he came for me to restart the printer. I turned it off and unplug the power cord. After a short wait, I reconnected the power and the printer. He was back to his old self well with everything that normal value. It's now a happy printer with a happy owner.

  Thanks for the reply. Take this into account if another comes with a problem on the copies where the copies n & B are very low, but color copies are very good.

  Thanks again.

  -John

• using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative. * beep *.

  using the color laserjet 3600n - I want to print in black and white, but it prints black and white negative.  * beep *.

  I was able to recreate what you see.   I managed to work around it by installing a different driver that is also supposed to be compatible with the CLJ3600.

  Please consider trying this as a possible solution:

  (1) uninstall the driver CLJ3600 by opening printers and fax machines, driver selection and right-click on it and select Delete.  Once it is removed, right-click on an empty space in the windows printers and faxes and select Server properties.  Click the driver tab, click the CLJ3600 and then click on remove.

  One when you're done, restart, and then install the CLJ3500 driver.  This is a previous version of the driver that has been implemented for the CLJ3600 and is compatible with the CLJ3600.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=315862&prodNameId=315867&swEnvOID=228&swLang=8&mode=2&TaskID=135&swItem=LJ-16838-3

  After installation, try printing again.

  The output I have indicates it will print is more negative.  Please let me know if you have success.

  One caveat about this solution.  The Color LaserJet 3500 doesn't support duplex.  Of workaround only works for two printing on the package of basic or the Color LaserJet 3600 N.

• My 2610 print correctly black not white documents in black, but copies in color (Pink).

  My 2610 correctly prints (from the internet or hard drive) black not white in black but incorrectly documents best (from the copier/scanner/fax) black n white paper in color (Pink).

  I have tried everything I know or have known. Of course, the black print cartridge (although a low replacement cost) is not the cause of the problem since it prints a black no white paper in black from the internet or the hard drive.

  ???????????

  Thank you and God bless you!

  Through a long trial and error process, I got lucky and I resolved and the resolution is not what I was expecting and makes no sense to me.

  Use the settings of the printer itself, I just changed the setting from "automatic" to the "plain" paper and the setting in 'text' value 'None '.

• How do I convert a photo to black and white but leave one object in color like a flower?

  How to make a photo I have taken, convert the image into black and white, but let an object such as a flower in color?

  Here is a small tutorial

  Lightroom > topic tutorials > Spot Color (B & W with little color)

• Work in CMYK color mode

  Hello

  I am trying to better understand how to use Illustrator to print correctly and my biggest hurdle is to understand how o use the colors correctly.

  I've done several tutorials and just need to clarify just to ensure that I understand them and I have do this process correctly.

  Issues related to the:

  1. I have read that it is possible to use RGB colors with CMYK to print and I sometimes see RGB color mixed with the CMYK colors in my color chart. Is it okay to use RGB to CMYK as my understanding RGB is to screen only?

  2 - is the right way to apply a CMYK color to work in Illustrator?

  

  3. I'm picking nuances using the guide in color in illustrator and when I double click on the individual color chart this screen with the little cube. I did some reading on this and there are sources saying that this has something to do with RGB modes? Still, leads me to believe that I do not apply color properly in illustrator. Here is the image:

  

  Would be really grateful for help with these issues, it will let me continue work knowing that my work is done in a good way before you start. It would be also nice to have suggestions or advice on the workflow.

  hope to hear about it.

  Z

  An Illustrator file is RGB or CMYK. The nuances that are the same color as the file mode a.

  You can set the color using different color modes, but when you click OK, the color is converted to the current document's color mode. It will change, and the numbers do not come back. The conversion is based on your color management settings.

  Some printers support the RGB files - it depends on the printing process and the machines they use. Print large format is often made with RGB files. As are some digital printing processes. Ask the print service provider about this.