GPIB write does not work, but ibwrt in MAX not

Similar Questions

• HP DVD Writer does not read or write DVD, but only the CD

  My HP DVD 1135t burner does not read or write DVD but only the CD. What is the problem? Please help me.

  CD/DVD players use different lasers for reading/writing DVD from the CD.  All indications would point to your laser DVD as having failed.  You could try to remove your drive and install it in another computer to see if the problem follows your player or your computer, but my bet is that the drive must be replaced.

  HTH,
  JW

• Impression on XPS Document Writer does not record anything

  When I try to print in XPS Document Writer, nothing is saved.  The dialog box appears asking you where I want to save it.  I select the folder, type a name and save it, but nothing is written.  There is no error message or anything. It is enough to save.  I tried several different applications (Firefox, IE, Word, Wordpad), but this does not seem to matter.

  One note, however, is that I can successfully print/save a test page to the printer (which makes it even more strange) properties.

  I'm on Windows 7 Ultimate 64-bit.

  Any help would be appreciated.

  * edit * I also tried to remove the device and add it again.  It does not either.

  After seeing your post, I decided to revisit this issue.  Apparently I've solved it.  My problem was that the files I tried to save to have full control to administrators, but not by my user explicitly.  To test this, I ran Firefox as an administrator, and I was able to save/print the XPS document.  This obviously isn't the most secure solution, so I just added my name explicitly under the Security tab for my home folder and propagate the changes down.  It seems that I can now save without problem (and run it as an administrator).

  It's not really make sense to me, since I belonged to the admin group.  It seems that the Windows UAC at least inspire you or something.  In any case, it's working for me now.  Hope that helps you.

• I have PC toshiba laptop, my cd/dvd. writer does not read the CD software and not able to write the media__

  itshow msg

  Insert the disc pls

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  ===============================================================

  Check with Toshiba support, their drivers online (update or reinstall) and their forums.

  Toshiba - Forums
  http://laptopforums.Toshiba.com/

  Toshiba - Contacts
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  Toshiba - drivers - access your model
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba - Support
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Form using the writer does not - 6i

  Dear all,
  
  I installed form builder 6i in windows 7-32 bit operating system.
  
  Form builder works fine but the problem is that if I press F1 (help) in the form builder it does not open using form builder.
  
  Instead of coming alert an error. The alert message is 'forms '. And windows in Help and support for the opening of the window...
  
  A patch I need to install to get the form builder help?
  
  
  Concerning
  Sankar.M.N

  You need Microsoft WinHlp32.exe for Windows 7

• Qosmio G20 - Slot Type DVD Writer does not in all disks

  I have a PC laptop Toshiba Qosmio G20.

  Problem: My DVD player is a slot type. I can't insert any CD/DVD disc even if I can push the disc inside full inside the drive, the drive does not it because it comes out as if I push the drive against a spring.

  But when I try to insert a disc in the drive while the system is turned on, it detects the insertion of media & power ups system to read the media, but still should not be in all drives.

  Is this a defect in the DVD drive & I can fix it or I have to go to a new?
  Is this a software or hardware failure or any other?

  I'll appreciate your answers fast & friendly.

  > Is that a defect in the DVD drive & I can fix it or I have to go for a new?
  > Is this a software or hardware failure or any other?
  I think it s a hardware problem.
  But just a question; are you able to boot from a boot disk?

  If not then this could be really a hardware problem and in this case, that the CD/DVD drive needs to be replaced in most cases, it s not possible to repair the STRANGE old the STRANGE old will be replaced by a new one

  Welcome them

• GPIB PCI does not connect to agilent 35670 A * IDN? query does not

  Newbie here. I try to get the agilent 35670A to transfer data using labview with gpib problem lies in the fact that I can't start because my pci card does not recognize the agilent. Ive downloaded a driver ahead of the hand. measurement and Automation Explorer is not with the entrance to the correct address. I am at a loss of where to go next.

  It is simply not true. You do NOT set the address of the GPIB controller at the same address for any instrument that you have connected. You should have just left alone to the default address of 0. I would say that finding a GPIB tutorial. Each device on the bus must have a unique address.

• DVD writer does not recognize 'NEW' blank DVD - r (Windows XP)

  Hello

  I have a question that has been annoying me a lot during the last few weeks, as follows...

  I have a Dell Optiplex GX620 computer is running Windows XP service pack 3, it has a cd/DVD burner in this model (HL-DT-ST DVD +-RW GWA4164B), I used to be able to burn CDs and DVDs fine, so please respond with lol 'maybe your drive doesn't burn DVDs' as you can see in the model # it's a DVD +-RW drive.

  But my problem is the following... for some reason the DVD burner does not detect the 'NEW' blank DVD - R, there is no problem of detection of blank CD - R disc and I can burn fine on the CD - R. But for some reason it does not detect blank DVD?

  When I put one in the drive, I don't get the popup asking what I want to do etc, or to go to WORKSTATION and look a the drive it shows no media present.

  I have Nero Platinum 15 installed in my burning software, which has a function of DISK INFORMATION, which also shows that 'no disk in drive '.

  I have re installed Nero...

  I uninstalled the drive and re installed

  Re, I installed the latest drivers for Dell Optiplex

  I bought a second axis of new blank DVDs

  I took out what I left little hair!

  Can someone provide me with a fix for this problem? ANY help is GREATLY appreciated guys!

  Hello

  See if that helps you.

  There is a "Fix - it" Microsoft for your problem on this link

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  If above doesn't fix it, continue with the help of Microsoft:

  http://support.Microsoft.com/kb/982116/en-us

  See you soon.

• DVD writer does not eject

  My engraver of DVD from Toshiba, TS-T632, ceased to eject. There is not a disc in the drive, in fact, I replaced with a new writer. He still does not eject or open to receive a disc. Manual unlocking does not open it and I don't know what to try next.

  Hello!

  What is the brand of your DVD burner?
  did you ensure that it is connected to the power supply?
  There indicator light?
  If it is stuck, you can use a clip to eject it.
  Thank you
  Makoi

• SIM card reader/writer does not work?

  The card reader present in the /devices of control panel and of the printers on the e drive, but it won't work.  Any help please?

  You can buy external USB card for as little as $2 readers these days in most of the stores selling computers.

  Good luck.

• the spell checker button is dimmed and the fate that you write does not work either. I'll have to use microsoft word, then copy / paste.

  See the question

  Restart Thunderbird with disabled modules (Thunderbird Safe Mode). On the Help menu, click "restart with disabled modules. If Thunderbird works as usual, there is an add-on or theme interfere with normal operations. You will need to reactivate the modules one at a time until you locate the offender.

• At 60: DVD writer does not write on DVD

  Hello.
  I have a toshiba dvd - rom sd-r6112 A60.
  It reads CDs and DVDs perfectly also burns CD.

  Problem:
  When you try to burn iso image dvd with either (nero, recordnow, alcohol, etc), the percentage indicator has reached 100% and says burn has been successful. But the dvd is still blank. It seems that nothing has changed. Trying to verify burned data will fail because nothing on the dvd set. (not done im test mode :-)

  Please help me.

  [Edited by: admin August 7 05 16:20]

  Hi witne

  First of all I think that it is not recommended to use multiple burning applications because it is possible that some of them are getting in the other. Try to use one of them. I always use Nero burning software and I had no problem at all.

  If you use burning software Nero, I see possible two reasons for your question:
  1. you must enable high compatibility mode that allows you to burn data and small then 1 GB
  2. check the option called simultaneous. It must be disabled and enable the option just burning

  If these options don't help t, please write again.

  Good bye

• Serial RS232 Communication VISA write does not

  I am trying to send a SPELL of 5003 01 command to my card that I am logged in via Rs232. This command should get my PCB to change play modes.

  I posted about this problem before thinking it was a problem with it not sent in HEXADECIMAL:

  http://forums.NI.com/T5/LabVIEW/RS232-serial-communications-visa-using-hex-values-seem-to-be/m-p/326...

  It wasn't the problem.

  I use the CTS line for flow control. I know that the CTS signal is reaching the computer of my PCB as I tested it and I know that the PCB can send data to the computer I get the answer correct 4 bytes in HEXADECIMAL when I use the reading visa to get my player to PCB data.

  I get a 1073807339 error when I try to write even when the read function is disabled.

  The only thing I can think is that LabView is not to recognize the signal CTS go down and, consequently, time-out.

  I use the good 9600 baud rate, 8 bits of data and no parity, 1 stop bit. I am using RTS/CTS flow control, but the RTS line is not connected. I don't think it should be a problem that RTS is used to indicate the Council when to send data to the PC to my knowledge and is not serious.

  FYI the written string section of the VI is unused. The string to write, that's where I'm seizes my "5003 01" command.

  Thank you

  Kyle

  I just thought of it. I had messed up the wiring of the PSTN line. She received the RTS line, I think. I thought I had it correct since the Tx line was correct. Thank you for your help on the problem of the HEXAGON.

• FPGA read/write does not not in cRIO-9073

  Hello.

  I'm stuck with a problem in the use of the FPGA Read/Write control please suggest a solution.

  I use cRIO 9073 and I'm trying to place an order ON / OFF of GUI-> RT-> FPGA host. I use a shared variable of the network to transmit the control GUI form to host RT and I use read/write control to FPGA. I also put a Boolean flag in the FPGA VI to control if the control is transferred to the FPGA.

  When I toggle the button in the GUI, I see the same change in the host of RT (shown as 16 probe in attachment 1). However the FPGA indicator (indicated as probe 19) remains the default false state. The FPGA VI is on attachment 2.

  Thank you

  Guilhem

  Your FPGA only reads the control once before entering the loop.  If you want to read control permanently, you must put it inside the loop.

• CRio-9014, 9116 and 9870 - series write does not

  
  

  Hello

  Yes, I was able to get things going according to my needs. There was a problem with the connector DB9 not wired correctly and Blayne Kettlewell, ELP Engineer at National Instruments helps flatten out. We are in business.

  Thank you

  Ajay