Help: A power supply using labview programming

Similar Questions

• A non programmable power supply with LabVIEW + additional programming hardware

  My company is interested in the use of LabVIEW to automate a non programmable DC power supply. The instrument in question is the U8001A device, but the idea must be the same, regardless of the manufacturer (the instrument was purchased while I was hired, or I would have opted for one with SCPI commands if that's a thing for power supplies):

  http://www.Tequipment.NET/AgilentU8001A.ASP?source=googleshopping&gclid=CMn-rPzAks0CFZM6gQodMu4McQ

  We have two connectors that would be plugged into the power supply and in the 'brick' that holds some sample we want to warm up. This has worked well for our initial target, but we are now interested in time these events alongside 1-2 other instruments that we are exploited (for example a-ohmmeter for quality control), where we can control all this through LabVIEW. Say, only allowing the power reaching the sample at intervals of 5 seconds, with widths of 1-2 seconds impulse.

  I'm sure I'll need a multifunction data acquisition device, and I already have my eyes fixed on the purchase of the NI USB-6501 (link below). My main question is about any additional material which is necesasry, if only a debate of ideas cenceptual on what I'm trying to accomplish. I can do everything I plan only through the acquisition of data, or are there other necessary materials, such as doors? What type of material is suitable for it? I apologize if this is the wrong sub-forum for this topic, as seems to be the subforum of material more appropriate upon publication. Thanks for your time!

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/201630

  Not even an analog command on this power supply... Range of tension and how much power do you need?  You may be able to make an operational amplifier circuit, but find out who can handle that many likely power won't be easy.

  Honestly, I say just to bite the bullet and get a programmable power supply.  It will be cheaper as you try to make a personalized tour to adapt to a peg in a hole square circle.

• What equipment I need another for the purposes of the on/off switch, adapt output voltage/current using labview program

  This is my first time to use labview, I want to use the program to control the DC power for the start/stop it or set the output to program automatically.

  Now I had the (supply) instrument, got a computer with labview. I know that I have to buy a GPIB cable, making a connection between the instrument and the computer. But I do not know what to buy? Cable GPIB or GPIB controller. Confused.

  Thank you

  A GPIB cable, by itself, will do nothing. You need a GPIB controller connected to your pc. With the NI USB-GPIB-HS controller, you can connect directly to a single instrument and no need for a separate cable. If you go with an internal controller to a pc (i.e. PCIe), you need a cable to connect the controller to the instrument.

  You can also check if the power supply has other options such as Ethernet or USB remote control.

• power supply used in use

  Dear Sir

  I don't know why my Laserjet M1217 display screen 'Used in use offer', could you please kindly tell me what happenning to my printer.

  Thank you very much.

  chung123, this error message indicates that the provision of toner he who is in the machine has been used previously. This message can carry to low/out toner or the toner has been charged.

  My recommendation is to replace the toner cartridge.

  I hope this helps!

• Using Powershell V3 to change the status of the power supply using WS-Management through iDRAC (PE r.620)

  Hi all

  I've been playing with WS-Management on the DRAC with PowerShell V3. I wanted to try to see if I could do the simple things. The task that I started has get and change of power on a PowerEdge r.620 State. I thought it would be fairly easy...

  Theres a lot written on this topic, but the examples from here

  http://en.community.Dell.com/TechCenter/systems-management/w/wiki/4374.how-to-build-and-execute-wsman-method-commands.aspx

  and here

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20206146.aspx

  both use WinRM in their examples

  I find it quite difficult to understand how I would achieve the same results using WinRM, but using the new v3 PowerShell cmdlets (get-CimInstance, New-CimInstance, Set-CimIntance, Invoke-CimMethod, etc.)

  I'm ok, get the basic information from the DRAC using these commands, but I must admit that I am a little lost in how to manage things from the endpoint reference (EPR). Each example of WinRM speak back EPR, then using those of the WinRM method call, but I just can't see how to do this with the new PowerShell commands

  IM asking if someone did or has examples of how do?

  It would be great if the authors of these documents could provide examples in PowerShell v3

  Hello jaydee180

  This document contains examples for powershell v3:

  http://en.community.Dell.com/CFS-file.ashx/__key/CommunityServer-components-postattachments/00-20-18-70-55/Microsoft-Windows-PowerShell-CIM-cmdlets-with-Dell-iDRAC.PDF

  Thank you

• Laptop HP COMPAQ power supply used on

  So I was waiting for my laptop at the end of the updates and I was about to turn on again when it suffice to stop and gave me an orange light on the side where the charger goes, instead of a blue light.

  I don't know what its from. It doesn't. When I press the power button, the orange light flashes.

  Tilted on its side when you perform updates because I wanted no more heating.

  that could play a role.

  I tipped it on its right side. He lost for a good 20 minutes.

  Any help?

  Thank you

  Try to remove the battery. Plug in the power adapter and press the power button to see if it lights.  If your laptop doesn't work with only the adapter connected, then either your power adapter, connector dc where the adapter plugs into the computer laptop or systemboard itself may have failed. You can test the connector when it is plugged by moving it gently to see if there is no change.

  Is your laptop still under warranty?

  It have tilted on the side would have no effect

• Control via RS232 interface labview DC power supply

  Hello world!

  I'm new to labview and I'm trying to control a DC power supply using a serial RS-232 (output voltage). I can't use an interface Gbspecifications TO have only a single module that is used for another task. Any advice on how to go about it in labview?

  Thank you very much!

  Find the driver for your device here: http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=510F94BB50256F51E0440003BA7CCD...

  It will work for GPIB or series with VISA.

• Power supply Equium M50-164 - pin polarity

  I am looking to buy a voltage converter to be able to run my satellite on board my boat, the 12v supply.
  I need to know if the PIN in the center of the input jack is positive or negative.

  Can someone advise please?

  Hello Dave

  I think that this issue you really need professional help. Power supply is serious and you need to have valid information on this subject.
  I recommend you contact the nearest authorized service provider.

  Technicians who disassemble laptops every day you need to know how the pins are connected.

• Investigation of the APT software and LabView programming

  Hello

  I'm new to LabView programming. I am currently using LabView 8.6. As you can see in the attached files, I wrote some code to synchronize the movements of axes X and Y of two controllers of Servo DC T-Cube using LabView programming. Now I'm tracing some Move_Absolute_Position data on graph XY in LabView. After that I sketched a movement of positions of engines, the graph only draw for the current position and erase previous data. Is there a way to track all the data on the chart? If you could give some examples, I would appreciate it.

  Best regards

  Jack

  JackBrown wrote:

  ... As you can see in the attached files...

  There are no attached files.

  To draw a story xy, the easiest would be to use the 'build xy graph express VI' and configure it to not erase the data between calls. You get this express VI if you place the xy graph in the express palette on the front panel.

• Power supply of database patch silence installtion

  Hello
  I have to apply database Jul 12419331 PSU on sub databases. I'm going with silent install (apply patch - silence) and need all steps in a script.
  
  Made Oracle gives a script automated for silent instaltion patch.
  
  Server:
  64 - bit sparcv9 kernel modules
  Have 2 databases
  
  Database:
  
  -Select database v$
  platform: Solaris [tm] OE (64-bit)
  -Select * from version $ v
  Oracle Database 11 g Enterprise Edition Release 11.2.0.2.0 - 64 bit Production
  PL/SQL Release 11.2.0.2.0 - Production
  CORE Production 11.2.0.2.0
  AMT for Solaris: 11.2.0.2.0 - Production Version
  NLSRTL Version 11.2.0.2.0 - Production

  Salvation;

  You have the grid? If so, that you can follow the note below to automate

  Application Oracle Database power supply using procedures of deployment in MS [ID 864316.1]

  See also:
  http://blogs.Oracle.com/gridautomation/entry/revisiting_patch_management_-

  Respect of
  HELIOS

• Control power supply 405 IPS by Labview

  Hi all

  I need to configure a 405 FPS of power Iso-tech and controll it via a LabVIEW code.
  Can I use NI-VISA to control this power via RS - 232?
  I looked everywhere but could not find the LabView drivers for this power supply.

  Can I ask you what to do? A bit of luck on the way to generate a Power Supply Labview driver custom? or VISA can help control power supplies? but I still need to find the driver for food? What can I do if no driver is available?
  Thanks in advance for your help.
  Best regards
  Serge

  Hello

  Thanks for reminding me.

  It comes in 2011 to LV and I used a model of power dc to start.

  I adapted only Initialize.vi and set up output.vi and you need to test only those.

  I have briefed the correct settings of series.

  Place it in instr.lib

  I would really like to see the State, but it is not a detailed instrument.

• How to use the Camileo H30 with Power Supply

  Hello

  First: Excuse my English, im from Germany ;)

  I have a Camilio: 30. its has been purchased used. I've only had the camera & the original battery.
  No supplements (such as usb or power supply cable original)

  what I want: I need to shoot for a few hours. The battery is unable to do. so I want to use it with a block of power, but when I put in (throughh a mini-usb connector) of the camcorder goes into charing (no actions are possible), but I want to make full use of the feature when the power is connected.
  How should I treat it?

  I got an a 2, 25 a 5V power supply, I think its enough... or not?
  The label on the side of the camcorder bottum said 5V 2A...

  Thanks 4 help me :D

  Greetz

  Hello

  If the Camileo H30 and I got this camcorder with battery and adapter supporting USB mini jack.
  The s AC adapter camcorder supports the release of 2A and 5V
  Its model DSA-10 p-05

  Google for this model, maybe you could get one from some dealers online
  Otherwise recommend that you check the other adapters supporting these values.

  For example this one:
  http://www.toshibadirect.com/TD/B2C/Adet.to?poid=484958

• HP 8200 elite CMT: can I use an external power supply for AMD Radeon HD graphics card 7770?

  I have HP 8200 elite CMT CPU in which 320 watts PSU is installed. I want to use AMD Radeon HD 7770 requiring more power (minimum 400 watts power supply) for maximum performance. But the fact is, the higher Watt PSU is not available for my cpu because its cables do not match that. So I ask if I can use the external power supply to power my GPU instead of the CPU power. Will be this harm to my PC?

  Kindly help me to solve this problem.

  Thank you

  Thank you for the information, @haseebkhan7310.

  I'm not a fan of using a separate power supply to power a video card.  It can cause problems.  However, here is a video that will show you how it can be done:

• Power supply for use in the UNITED Arab Emirates

  Hello

  I just bought a Time Capsule of the airport and an Apple TV (4th gen).  I'm moving to Dubai for work and I intend to take with me.  I can't find out how to replace the power supply for use in Dubai (plug type G).

  • Can I just buy a travel voltage converter?
  • What is the frequency difference (US is 60 Hz and UNITED Arab Emirates is of 50 Hz)?
  • Could I just buy a 'EnergyPal travel Charging Station ETCS04' and connect directly?

  Thanks for any help!

  The airport Time Capsule and the Apple TV work on 100-240 Volts and 50/60 Hz automatically, so they'll work pretty much anywhere in the world if you have the map of the right ankle.  A voltage converter is NOT necessary.

  You can buy the cards you need to any store from the airport, luggage, in Dubai store, etc., most of the hotels the.  If I remember correctly, Dubai uses the same type of plug that she used in the United Kingdom, as well as should work as well.

  http://www.Amazon.com/Ceptics-grounded-Universal-Plug-adapter/DP/B0080R95XI/ref= sr_1_1? ie = UTF8 & qid = 1455557366 & sr = 8-1 & key...

  I do not think that the higher 5 GHz channels are permitted in Dubai, so be sure to put the time Capsule to use a lower numbered GHz 5 channel... 36, 40, 44 or 48.

• Satellite P100-347 does not stop when it is used on the power supply

  I have a new laptop of P100-347 games and I have 2 problems. Can anyone help?

  (1) when I use the usb port on the left side of the laptop, the laptop seems to restart the same time that I plug anything into it! I called Toshiba and said to update Bios, so I did (version 240 up to 330). But as soon as I did it started to the following problem:

  (2) when I run the laptop on battery, I can turn off the phone by pressing the power button or by clicking the windows locked. But as soon as I plug the power supply whenever I want to stop the laptop, the laptop just restarts. Does anyone have any ideas?

  Thanks for the comments!