Help! Challenge continues to restart.

Similar Questions

• Satellite L300D-110 - white screen and continue to restart

  Hello

  I have a L300-110, this just started to happen when I turn on the laptop light power green lights then get white screen but if continue to restart the laptop starts to work again.

  Can anyone help?

  Hi thm1ele,

  You can access the BIOS or see something on an external monitor?

• Blue screen of Windows XP, the computer continues to restart, can't get into safe mode, will blue screen with installation as disk, can enter the CMOS?

  Restart Windows xp continues and in the end, the blue screen of death leaves the following error: 0X0000007B (0XF78D2524, 0XC0000034, 0x00000000, 0x00000000) can anyone help?

  If your machine is blue-screening after booting from the XP installation disk, it suggests that your problem is with the hardware rather than auto-run.

  I recommend taking your machine to a local service shop, unless you are confident enough rooting in the bowels of your computer.

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC | The lazy three fingers

• Help please - Windows update - restart issues (and upgrade to Windows 10 questions?)

  Hello

  I wanted to switch to Windows 10 but got stuck on the "start download" page, as have other users.

  Looking through the other questions on this site, I have seen that Windows update may need to complete before you start with Windows 10.

  I had not run windows update for a long time I thought that would mean Windows 10 would install and I wasn't ready for this, but now I am.

  Then I ran windows update and more than 150 updates have been installed.

  However, he now says:

  "Restart your computer to install important updates

  Windows cannot update services and important files while the system uses them.  Save... "

  I rebooted, shut down, rebooted several times, but this message continues to appear in the Windows Update window.

  Still, the update of Windows 10 stuck initially download.

  I ran disk cleanup in safe mode, as well as normal and tried to restart, but it did not help.  I tried the troubleshooting windows update option, but this did not help.

  I used two tools, the Microsoft FixIt who did not help and a WindowsUpdateDiagnostic.diagcab file which allows to find the two errors and saying: he fixed them, but this still does not work, IE always ask me to restart and Windows 10 gets stuck to download from.

  The two problems it finds are listed as:

  "Windows Update error 0 x 80070005(2016-05-30-T-08_49_44P)" and is listed as fixed

  "Problems install the latest updates" and is considered to be fixed.

  I am at my wits end and would be really grateful for the help.

  If this becomes technical, please help me in using a step by step method or referring to one for me.

  I have a laptop of Toshiba Windows 7 64-bit.

  Thanks in advance

  EDIT: I ran the above diagnostic tool and the error was fixed progresses over time, that is to say it is correct to say 09:03 now...  Also, to revise accordingly the so-called updates installed, many of them, but not all, have the status of a failed.

  What to do about all this?

  I suggest you to download the tool for creating Windows Media 10 ISO and make a place in upgrade.

  Download the update of Windows Media Player 10 tool creation build 10586:

  http://www.Microsoft.com/en-us/software-download/Windows10

  How to download an ISO using media tool:

  http://www.tenforums.com/tutorials/9230-Windows-10-ISO-download.html

  How to make a upgrade in Place using method 1:

  http://www.tenforums.com/tutorials/16397-repair-install-Windows-10-place-upgrade.html#step6

  If this does not work please restart your computer and wait 20 minutes for the system to operate before you download the information needed to help me investigate your problem. When the review much, not Event Viewer log files all problems show in the period immediately after the computer has booted.

  Please provide a copy of your system information file. Type the system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. Not to place the cursor in the body of the report before exporting the file. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download the file to your OneDrive, to share with everyone and post a link here. If the report is in one language other than English, please indicate the language.

  Please download and share with everyone a new copy of your log System of your event viewer on your disc one and post a link here. It allows to avoid confusion if you delete all previous copies of the log files of your OneDrive.

  To access the system, log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window, expand Windows logs and select System. Place the cursor on the system, select the Action in the Menu and record all events like (the evtx default file type) and give a name to the file. Do not offer not filtered files. Do not place the cursor in the list of reports before selecting the Action from the menu. Do not clear the logs so that you have a persistent problem.

  For assistance OneDrive see paragraph 9.3:

  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm

• EFI disk0s1 not mounted. screen shows gray with help file when I restart

  I had these problems with my recent Mac.

  1. it freezes for a few seconds. Then begins to work properly. And then freezes. The beachball keeps spinning and I can't access any of the applications.

  I tried restarting. But came up with another question. The gray screen of the charges and file aid continues to Flash.

  I tried from the recovery mode, but I get the Internet (OS X Lion). I'm under El Capitan. In disk utility, I check and repair the drive. Stop and try again. Now, there are two current icons and off - no logo entry sign and apple. If I'm lucky then after 40-50 seconds, Mac starts up.

  Now, I tried to make the EtreCheck, and he gave me more results for disc

  Disk information: ⓘ

  HTS545050A7E362 disk HARD APPLE disk0: (500,11 GB) (rotation)

  EFI (disk0s1) < not mounted >: 210 MB

  Macintosh HD (disk0s2) /: 499,25 (Go 110,18 free) - 70 errors

  Drive failure!

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  HL-DT-ST DVD - RW GS41N)

  
  

  That's what worry?

  
  

  What can I do to fix these problems?

  Disk0 unit 1 is not the problem. This is the EFI partition, which is never mounted, because it is used only by the bootstrapper, long before that the file system is initialized.

  Your problem is 70 errors in disk0 tranche 2, the volume Macintosh HD. This hard drive (the entire disc) was his. Dead. in ruins. You need a new drive.

• Where is the help on the topic: "restart with disabled modules.

  In aid of the menu choice "restart with disabled modules" is trying to find out what would be the consequences of this command, but I can't get any result on this SPECIFIC command. If I try, I definitely will disable my Add - ons?

  I have to ask this question because I've had nothing but problems with Mozilla Addons lately, especially the themes.

  I'm tired of Firefox

  Basically what the restart with disabled modules is it closes your Firefox and them it opens in safe mode, which is a temporary mode where all add-ons are disabled, and the settings are set to their default values. It helps you to be able to test and see if your question is without third-party variable. Then, when you close and restart firefox, it starts as before without Add-ons.

  Questions to troubleshoot Firefox in Safe Mode is an article that explains a bit more.

  What problems with modules you meet specifically?

• continuous laptop restarting after an update

  When I turn on the laptop the performances last updated 3/3 0% and towers then turns off and restarts and then just did the same thing again and again. I tried the option while pressing F8 on startup to the top and nothing works. Help, please!

  Hi dddanni

  Refer to this link:http://support.microsoft.com/default.aspx?scid=kb; EN-US; 949358

  Response and let us know the status of the issue

  Thank you
  Anthony

• Help! Lost on restart system restore points!

  I have Windows Vista 32-bit to Windows 7 Home Premium 32 bit upgraged. I can manually create restore points, but they are deleted when I restart the system. Can someone please help?

  Thank you! :)

  Hello
   
  1. have you installed any third-party backup tool?
  Method 1.
  a. Click Start, type services.msc in the start search bar and press ENTER.
  b. Locate the Volume Shadow Copy service.
  c. click cliché instant volume, then select restart.
  d. now cliché clickVolume-right and select Properties.
  e., under Startup type, select automatic.
  Method 2.
  Please check the use of disk space for the protection of the system by the following steps:
  a. go to start, right click on computer and then click Properties.
  (b) in the left pane, click system protection.
  c. check the Protection status of the drive that you want to use the system restore on.
  d. Select the drive, and then click Configure.
  e. move the slider of the use of Max to the right to increase the disk space for the protection of the system.
  f. click OK.
  Create a restore point and reboot and check.
   
  If the problem persists, check the System event log and see if there is any error concerning the restoration of the system, VSS or VolSnap, at the point where you saw last deleted restore points. If so, please reply here.
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Vista 64 bit continues to restart the PC after the update

  Sunday Vista 64 bit download and put up-to-date and closed without any problem. The start-up of the PC today for the first time since the update screen reports ' Configuration updated step 3 of 3 0%. He shows this during approximately 1 minute before the screen turns off and the PC restarts automatically. No error message is given.

  I tried to start in safe mode, but the problem is the same. I tried to select menu to return to the last known good configuration startup option too, but it is also unsuccessful.

  I suspect it's a corrupted download, but how to fix it?

  Any help most welcome

  Thanks Mick,

  Initially, I couldn't Windows to boot mode safe that even then he showed the configuration screen. Tried a bit of support tools under F8 start up, but ultimately went to a restore point and deleted updates of two windows on Sunday. That seems to have fixed.

  Thanks a lot for your comments that got me to the answer.

  Concerning

• BlackBerry Smartphones Please help - my phone keeps restarting/reloading. It won't turn on, and I need to access my calendar to see if I need night tonight or tom meds

  Hello, I hope someone can help me. I have medication alerts on my phone, without it I don't know if I need my meds tonight or tomorrow night.

  I downloaded a few free apps now in app world for blackberry on my phone as I have done several times before.

  He asked a reboot once completed. so I clicked to restart. Since that time (4 + hrs) sound was reloading all the time, it is right at the end and restarts it again without turning on

  I removed the battery and tried to turn it on, it does the same thing. I tried a reboot after removing the card and sim, then both and still nothing.

  I also tried to boot in SafeMode by hiolding down the ESC key but it dosnt work.

  Help, please

  You are able to reboot your device in SafeMode as shown in KB17877?

  This could remove some data if you do not have a current backup

  I guess, because it is taken in a reboot cycle, when you connect to the desktop software it does not have a stable connection to reinstall your software?

  If this is the case, remove the battery and keep it off when you connect to the desktop software. You will get a pop up that the device cannot connect and there should be buttons retry, update and cancel. Select Update and you will then be able to reinstall the latest version of the device software.

  When the load progresses, you will see a step that says "waiting for initialization of the devices '. At this point, insert the battery and recharging must complete.

• Windows 7 won't Shut Down - continues to restart

  Hi all

  I can't get my new HP 6550 probook b to close. I can force by using the power button, but I can't stop using the Shut Down options on the screen. Can someone help me? When I force using the power button, I get a black screen that tells me that the computer has not been closed correctly and that I can't continue in safe mode. I need a solution because it drives me crazy!

  Hi Toronto1982,

  1. what happens when you try to shut down the computer?

  2. Since when are you facing this problem?

  Step 1

  Check if the problem occurs in safe mode.

  Start in safe mode.
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  Put your computer to boot in order to check if the problem is caused by any application.
  http://support.Microsoft.com/kb/929135

  Note: Please make sure that the computer is configured to start as usual by following step 7 of article.

  Start in normal mode and check the status.

  Step 3

  If the problem persists, check the event viewer.

  What are the information in event logs? (Event Viewer)
  b http://Windows.Microsoft.com/en-US/Windows-Vista/What-information-appears-in-event-logs-Event-Viewer

  REFERENCE:
  A computer that is running Windows 7 does not start when force you the computer to shut down
  http://support.Microsoft.com/kb/974719

  Bindu R - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think

• Possible to continue after restarting encoding?

  Hello

  Master Collection CS5 using, is it possible to continue the encoding with SOUL after a reboot (planned, or in the case of a system failure, as happened to me)?  Looks like a simple break in the SOUL, followed by a restart, loses all encoding progress at this stage.

  Best,

  Chris

  Nope. I have to start over.

• After the upgrade to 10.0 today, came to 'reboot' action. Does not open after... continue to restart again and again restart.

  Tried to uninstall. When you click on 'delete' again invited to restart to the new version. Still, it wouldn't uninstall. X 2 the computer unplugged. STIL told to restart. Tried to restore the system to yesterday, but always 'reboot' happened every time. It cannot open Firefox. It appeared to download the upgrade normally until the restart action.

  Thank you! I was able to uninstall after downloading Firefox on my desktop. There are always a few files that I could not remove at the time, but they seem to have disappeared now.

• Help, please! KERNEL_DATA_INPAGE_ERROR restart blue screen

  Hello

  I've known the KERNEL_DATA_INPAGE_ERROR blue screen which causes reboot at random times when I use my computer. I tried a number of options and have been in contact with a number of Microsoft employees to try to solve this problem, but so far nothing has worked. Here is a list of whathas was made up here, but all to no success. These actions are without particular chronological order:

  Ran CHKDSK /R in command prompt

  CHKDSK ran sfc and dism in command prompt

  A ran CHKDSK/X/r/f in the Safe Mode command prompt

  A ran CHKDSK /F /R in Safe Mode command prompt

  Analyses with HitmanPro, ESET, Norton and Malwarebytes

  A run MSDT while with the Microsoft Staff

  Update various drivers

  Convenience of Ran with Microsoft staff

  Finally, I performed the update on my PC, but little time action after I did, I had projected again blue.

  My OS was 8.1, now demoted to 8 since I refreshed.

  I'm ready to remove and reinstall windows as a last resort if nothing else can be done, if that would solve the question. I appreciate the help that can be given.

  Kind regards

  Josh

  We need the log files themselves (called a DMP files) because they contain the only record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.
  Please follow our instructions to find and download the files, we need to help you fix your computer. They can be found at here
  If you have any questions regarding the procedure, please ask

• [HELP] SMV disappeared after restart of the host - 5.5 ESXI, Vcenter Server to the same host

  I restarted the ESXI using classic Vsphere Client. Now, all virtual machines have disappeared. I tried to connect with Vsphere Client and workstation and the list is empty. I can't access the Vcenter server since it is a virtual machine that resides in the home.

  The data store is a local disk. The data store is still there and the amount of disk space used is correct. I don't see the virtual machines in the inventory. I have re-installed ESXI 5.5, refreshed of store data and what not, there is nothing there. I am freaking out and don't know what to do.

  EDIT: I am able to navigate the data store manually by creating the new virtual machine and select the existing virtual machine following this guide but I'm not sure what is the reason for which the files would be missing or corrupt

  http://techhead.co/VMware-ESX-how-to-easily-recreate-a-missing-or-corrupt-vmx-file/

  When you browse the data store you see the virtual machine and their records?

  If you see the virtual computer files, you can open the folder, right click on the .vmx file and select Add to the inventory. who will get your VM in the inventory.