Ho I'm tun the wireless on my hp 6730 b

Similar Questions

• How to do a right click on the wireless mouse?

  Right-click on the wireless mouse?

  Open System Preferences > mouse and select the tab k Point & clickthen the tab more gestures to configure your mouse.

• Diagnose/improve the wireless Airport network

  I'm no expert on wifi networks, but try to improve ours.

  I have an Airport Extreme, connected to a modem of the Charter down.

  Upstairs, in my office, that I have an Airport Express with a printer connected via USB.

  I think I Express correctly configured to expand or develop, or whether the network.

  My MB Air is sitting on a desk about 7 feet to Express in my office.

  If I connect to the Express via Ethernet to the MB Air USB connector, my download speed is about 65 MB/s, download about 4 MB/s and the Ping on 31ms.

  If I connect via wifi, download is about 20 Mb/s and the stay of the upload and the same ping.

  Make sense?

  Anything to improve the wifi?

  When websites take a long time to react and fill the page, what is the download or ping, or both?

  Thanks in advance for all the education on wifi. Enjoy.

  Make sense?

  Makes perfect sense.  First, we assume that the Express extends the network by connecting using wireless back to AirPort Extreme, correct?

  When you "extend" with only a wireless connection and connect using wireless on your Mac, you will generally lose about half or more the speed on the network.

  Why? The wireless should make a "leap" in Airport Extreme for the AirPort Express. He must then make a second "hop" of the AirPort Express using Mac wireless. It will take a lot of overhead or bandwidth.

  When your Mac is connected directly to the AirPort Express Terminal, the wireless is only to make a "leap", so find you speed or bandwidth that is lost when the Mac connects to the Express on a second Wireless 'hop '.

  You want to improve your network?  Connect terminal AirPort Express to the AirPort Extreme, using a wired Ethernet cable connection.  There is no loss of speed of the signal through the cable... until approximately 325 feet or 100 meters... so the Express receives a signal of full speed... rather than a slower wireless signal... because the wireless signal slows the other he has to travel and also slows down if it encounters obstructions in the signal path... like a wall or a ceiling.

  When websites take a long time to react and fill the page, what is the download or ping, or both?

  Could be both, but is usually a DNS problem. Try to use the Open DNS servers or the servers of Google to see if things improve. In general, the DNS servers are better than those that use your Internet service provider.

• I can load the wireless keyboard using the IPhone charger form?

  I can load the wireless keyboard using my IPhone charger?

  Strictly speaking, they are not quite universal.  It varies, but what happened to the one that came with the keyboard?

  Take a look at this document from Apple.

  https://support.Apple.com/en-GB/HT201700

• Need help with the wireless internet Power Book G4

  Hi-I recently inherited a Power Book G4.  I have problems to connect to wireless internet.  According to the Profiler systems, it has an AirPort Extreme card, but there is no icon on the screen wireless.  Advice to connect would be appreciated!

  Thank you-

  Stephanie

  The icon in the menu bar can be hidden or displayed.  The setting is the system network preferences pane.  Where it says display, select AirPort.  There is a checkbox for the State of AirPort show the menu bar.  Since the AirPort icon in the menu bar, you can select the a local wireless network to join.

  This pane of system preferences, you can use the more specific configuration settings, although the default settings work often unless you use special parameters with your wireless router.

  AirPort Extreme Card maybe for 802.11b and gand not n.  If your wireless network is configured for 802.11n only, you will need to change this setting to allow to 802.11 g (on the wireless router).

• Ink advantage 2545: changed the name of the wireless router and now ink advantage 2545 does not connect and I'm out of ideas

  I have a Toshiba laptop 64 bit running Windows 10 Home, 8 GB, 1 t hard drive.

  Router is a Samsung phone using Android because it was the only router that I could find which would take the wireless signal.

  I live very pastoral, no neighbours for miles, so I never saw the need for a password on my router.

  Now, some people are installs in less than 400 feet from me, and I think they're piggybacking on my Wifi because my access speed has slowed considerably since they moved in.

  So I decided to change the password of the router, unfortunately, I can not put in any password I want.  It gives me the opportunity to have a predefined password.  So I changed the name of the router I could do without problem.

  My computer very quickly without any problem, however, my printer which worked great for a year with the old router name does not connect on the new name of the router.

  Here is what I tried:

  I had hoped he would ask me for a new name / password, but it did not.

  Then I plugged a cable between the printer and the laptop in the hopes that it would produce a different kind of results.  It has not changed anything.  There is no screen menu on what that be like this on the printer.

  I pressed the wireless button that has the flashing blue light and nothing happened.

  I pressed the button, don't know what it is, but it has a white light, and nothing happened.

  I went on the HP site and followed the instructions but he just said do not connect the cable until told to do so.  So I disconnected everything, lights out and turned back on and still no connection and no invite to plug whatever it is.

  Y at - it everywhere where I have being a novice could get instructions on how to get this working?

  I appreciate any help you can give me.  Thank you.

  Hello

  I think you are talking about SSID. Please, think of it as a new router and use the following ways to correct:

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html
  
  Kind regards.

• Photosmart more B209a_m: Virgin Super Hub does not connect with the wireless printer

  We recently upgraged to a new blank media 3 hub, the printer is connected to a Hp Windows Vista desktop via USB, other devices (laptops and tablets) could access the wireless printer when the computer is turned on.

  I also created the same printer to be used wireless by the other devices without the Office of marketing, it was a pain having to keep it logging on when he fell asleep. The printer had a different name if you are using one.

  After that the hub of the Virgin was installed I can is no longer using the printer without the Office being wireless, the new Center can not find the printer connects as is done before that other laptops, I had no problem with my old hub and a separate router.

  I've tried everything as suggested by Virgin (not much there) and reinstalled my drivers for the printer. Any suggestions what I can do?

  Hi @Confused_Nanna,

  Welcome to the HP Forums!

  I read your post about how you cannot connect your HP Photosmart b209 printer to your wireless network. I'm happy to discuss this issue for you!

  Please, try the steps in this guide, printer is offline (Windows) as well as this guide, the printer is not maintaining the wireless connection.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope that this post helps!

• Cause first of the wireless problem?

  I've had my laptop repaired a week ago, as the wireless card was more is detected. I bought a dv6258se in Feb ' 07, he was really running hot, the GPU ran above 80 ° C, 55 ° C CPU all idling. I installed F.3D as soon as it was released in Nov ' 07 and there really the time down, and a year later, the wireless gave out. The motherboard was originally a 30B 7 Quanta, and it's still a 30B 7 Quanta, flashed with the version of BIOS F.40 even if my the driver model page shows later as F.3D.

  So, what's the problem? I can probably keep it on the downlow time if it was caused by excessive heat. If I got was a band-aid to keep me more of the extended warranty, while HP does not solve the problem for free once again, then they did a very good job of it. I have not enough income available Clipboard $ 1100.

  F3D is the last Messenger for your model:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & lang = to & Product = 3340175

  F.40 is posted on other models, but can't say that I recommend:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-64061-1 & LC = on & DLC = in & CC = US & lang = to & os = 2093 & Product = 3546969

• How to activate the wireless adapter

  I currently have a HP Pavilion 17 computer laptop with Windows 7 Professional.  A few times in the past in the unit's wireless adapter stopped working.  I don't remember what I did to get it working again, then however at this time I can not activate even if I followed all the steps to change the settings of the adapter on the network and sharing Center.  When I select Connect, it simply shows that it is not connected.  Nothing I have tried seems to help.  I have a unit of Belkin Wi - Fi that works and my laptop runs as long as I have an Ethernet cable connected.  However if I disconnect the cable from the laptop does not connect via wireless adapter.  In the past he would always stay connected to the Wi - Fi connection even if I disconnected the cable.  Please give me any thoughts you had to solve it.  Thanks in advance for your efforts and help.

  I just wanted to know that I found the solution to my problem with the help of a response of the same issue posted last year.  Repeated pressing the F12 key with the picture of an airplane on the wireless card.  Forgive my ignorance, but thanks to all who took time to try to help me.

  OldmanDon

• Scope of the wireless connection for remote access to TimeCapsule

  I use my TimeCapsule as long wireless rather than "create a wireless network, as my ISP does not allow for the time capsule to use as my router.

  I post this question because I would like to access my TimeCapsule remotely and the hard drive connected to it.

  Now I'm Back to Mac enabled on TimeCapsule and what I believe is the appropriate port forwarded port to allow a connection outbound to it, but cannot be accessed remotely to the TimeCapsule. Any ideas?

  

  

  

  

  

  Two problems here:

  (1) the "extend a wireless network" is a defining Apple owner who is only used if the Capsule is wireless extension of the network from another router from Apple. It is not compatible with the wireless to a 3rd party router.

  This parameter must be "create a wireless network" using the same wireless network name and the password of the wireless network FIOS with time Capsule of the FIOS router by a permanent connection, cable connection through an Ethernet cable.

  (2) the time Capsule is configured to act as a router, when it should be configured to act as a "bridge"... Since you already have a FIOS router 'upstream' on the network. If the Capsule is configured as another router on the network, which creates an error Double NAT on the network, and it is unlikely that Back to My Mac would function at all in this type of installation. The setting for the time Capsule router Mode must therefore "Off (Bridge Mode).

  Since the Capsule must be in Bridge Mode to work properly with the FIOS router, it's the FIOS router that must be set up for Port Forwarding. Then, in Bridge Mode time Capsule will cross the FIOS router to your network equipment settings.

• Laptop suddenly loses the wireless out of sleep mode

  I have a HP Pavilion g7 laptop running Windows 7 Home Premium 64-bit.

  Last month, it was the loss of connection Wi - Fi & will not return to the top of the standby mode. When I open the screen, the "enlightened" shows power button but the screen remains black and wireless orange shows (f12) instead of the blue button. I can hard down and restart in safe mode to get the screen to the top. So, I have to restart the computer several times to get the wireless to turn back. By pressing the f12 key has nothing to do with it. I have a HP desktop which is perfectly fine - no problems at all.

  Nothing has changed regarding the new routers, software or anything like that.

  Welcome to the forum, TM_Cali,

  Consider / try the following:

  WiFi disconnects after sleep - Wifi doesn't wake up

  IF you use no SHARING, try:

  Windows key + X > P (opens the control panel) > icons > network and sharing Center >

  Change the adapter settings > right click on your connection > properties >

  Scroll down in the Networking tab > uncheck the IPv6 BOX > OK

  OR - a better solution:
  

  Windows 8:

  Windows key + X > M (opens Device Manager) >

  Windows 7:

  Control Panel > display icon value > Device Manager >

  Next...

  Network adapters >

  Right-click your wireless adapter > Properties > Power Management >

  Select as appropriate:

  Clear the check BOX "Allow the computer to turn off this device...". »
  CHECK 'Allow this device out computer' >

  Ok

  Bluetooth:
  

  Windows key + X > M (opens Device Manager) > Bluetooth >

  Right click of your Bluetooth adapter > Properties > Power Management >

  Select as appropriate:

  Clear the check BOX "Allow the computer to turn off this device...". »
  Ok

  ======================================================================================
  

  For laptops:

  Pay attention to the warning to leave the device connected wireless and battery operated.  The device consumes little power; However, if you run your battery is very low, it could have an impact.

• Satellite L10 - could not get the wireless operation

  Hello

  I reformatted my Satellite L10 and managed to pull the best of drivers to use, but I can't seem to get the wireless working.

  I installed the Realtek driver http://aps2.toshiba-tro.de/wlan/?page=downloads

  I also tried to install the InProComm driver, but the installer crashes just after a while.

  Anyone know what could be the problem? All solutions?

  Thank you

  Naushad

  Hello

  What operating system do you use?
  I checked Toshiba driver download page and looked for the driver for Satellite L10. Here, I can only find a driver Intel WLAN for Vista and the driver InProComm for XP but I can t find a Realtek WLAN driver.
  It seems that your laptop is equipped with an Intel card check so the Toshiba site again:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Before you install the driver WLAN make sure that WIFI is turned on with the hardware switch on the computer laptop and FN + F8.

  Good bye

• Need info on the wireless on the Satellite C660D - 10 p

  Hello

  I installed a new operating system (Windows 7) on my camera last week because I wanted to format the HD.
  Now, my laptop is not able to identify the network adapter.
  As a result, I have to install the driver for the wireless network card, but I don't know the name of it.

  So please, can you give me the name of the card Wlan (company and type etc..)?

  Information on this laptop:
  Satellite C660D - 10 p

  Thank you very much in advance
  Greetings from the Germany

  I found the specs of the laptop on the Toshiba page German and his clearly stated:

  + Manufacturer: Realtek +.
  + Wireless technology: Wireless LAN +.
  + Version: RTL8188CE +.

  Welcome them

• Satellite Pro A40 fell on the wireless network card; Damaged PCMCIA slot

  This morning my Satellite Pro A40 (Celeron 2.6) fell 40 cm. He fell right on the wireless network card that has been inserted. This card is still alive and so is the rest of the laptop, but the PCMCIA location is little damaged. I can insert PC cards almost completely, just the last piece (when the pins are) wrong.

  I removed the cover near the CPU, and there, I could see the inside PCMCIA slot; I could see the main part and the last part where the pins are. That little part as is pushed upward, as you can see in the pictures.

  I think I'd be able to fix myself this PCMCIA slot, but I can't remove it. I removed all the screws on the rear plate, but he is still blocked.

  Pics:

  PCMCIA slot

  The PCMCIA location; on the left, you will see the part with the pins, which is pushed upward. It's also what I see when I look at the pins in the PCMCIA slot. as they are pushed down, but I don't think they are folded.

  Wireless network card

  Wireless network card; It is a little damaged but it still works.

  Does anyone have an idea how I can remove the back plate, or another way to remove the PCMCIA slot and fix it?

  Hi Steve

  Well, I can give t well you not answer how you can just remove the PCMCIA slot.
  There are a lot of screws and to my knowledge, it is necessary to remove all covers and screws that are placed at the bottom of the unit and inside under the keyboard.
  Please check this specific device. Perhaps you have overlooked a few screws.

  But if it is impossible to remove the PCMCIA slot of the unit, I recommend to ask the service partner for a detailed instruction.

  Good luck

  Good bye

• Deactivation of the wireless network on R200 map

  We started to use Landesk to create our images and is one of the advantages of Landesk may detect the hardware automatically and assign the correct driver during the construction of the image

  We are now buying R200s but when auto discovery runs in the Landesk build picks up only the wireless lan card.

  We want to pick up the wired lan. Is anyway to disable the network wireless in bios?

  Hello

  Unfortunately, I'm not very familiar with LANDesk technology.
  But I found this Intel page with a few troubleshooting tips:
  http://www.Intel.com/support/LANDesk/networkmgr/index.htm

  Moreover, as far as I know, that you can disable only the wireless card is in the Device Manager. I don t think you will find all the options in the BIOS

  Good bye