Homegroup and network cut the connection. Internet connection remains constant.

Similar Questions

• Impossible to connect to the wireless network when the wireless Internet is filled to connect to the Local network

  I tried to fill the connection between my laptop Wi - Fi and an ethernet cable LAN via the connection to the Local network for my xbox 360. However, when the connections passed the wireless connection would show that it is disconnected and would not reconnect. When I tried to repeat the process sometimes the same thing happens sometimes it says that it is still connected.

  However, be that as it may, both times I could not load any page of the website from my laptop and xbox connect any.
  How can I create a network bridge and get the wireless internet to connect please?

  Any help to fix this would be appreciated,
  P

  This Microsoft Knowledge Base article might help: bridge may not work with a Non-Promiscuous Mode network card .

  If not, I recommend to delete the network bridge and enable sharing of Internet connection on the wireless network connection. Boulder computer Maven
  Most Microsoft Valuable Professional

• Setting up Apple tv and stuck on the connection to the network screen

  Apple TV has tried to connect to my wifi.  He was slain on the connection to the screen of the network for 30 minutes.  No error message, just stuck.

  David, if, after checking your network on a different device - and assuming that

  your scope, that it still can't find your network quickly, I suggest you tv

  you restart.

  Tom

• Router E1200 works not - error 3005 (and network does not connect by hand)

  I am trying to put in place a new monitor of N300 E1200 and am not having any luck. Using the Cisco Connect ends with an error in step 'Validate the connection' each time, telling me:

  Error: 3005

  An HNAP call to the device failed because the HTTP connection was broken.

  (If it is relevant, the serioal number, type of connection and IP (WAN) all happen as "unknown" in the details of the error).

  I am able to set up the router manually via the access by web browser. I can name the wifi network, set up security, and even see and authenticate to the network of my devices, however, no connection is available when it is connected. (The internet connection is good - when I move the incoming cable between the router and computer, I instantly have access - so perfect this post)

  I also tried all the basic steps of reset and restart all involved several times, but I always end with the same result - 3005 error in the application configuration, then on a manually configured wifi network that seems to be working and can authenticate devices, but does not include any internet connection.

  I am at a loss at this point - here someone has any advice? Thank you very much for your time and input.

  -e.

  Then you must configure PPPoe in the router, unless your ADSL modem is already acting as a router and not the PPPoe.

• EA4500 and PS3 abandons the connection

  I had a router WRT54G2 and started having trouble with my PS3.  It would connect for a few minutes then she would lose the internet connection.  I thought that maybe it was the router so I have now from the EA4500.  The same problem occurs again.  I have all my other devices wireless connected to the EA4500 without any problems.  The PS3 will connect and connect and then two or three minutes, I get disconnected.  I called Sony and Cisco to help and they were not able to understand the problem.  The PS3 is showing that my network has almost 100% signal strength, so this isn't a problem.  If anyone has experienced this or can help, I would be very grateful!  Thank you.

  @2shibas

  Hello

  Is this connected by cable or wireless your PS3? Have some port numbers for Sony, so you can do Port Forwarding on the user interface of the router? If this is not the case, try to contact Sony and ask for the ports necessary for the opening of your PS3.

• Connection to the local network after the connection to the Client AnyConnect Secure Mobility Client

  I connect to my network of business using Secure Mobility Client of Cisco AnyConnect.  Once connected, I can no longer print on my printer LAN attached and other local resources.  I use the router E4200 of Cisco/Lyncsys on my local network and can re - connect to storage on the local network by putting in place of Port Forwarding port 21 and the sharing of MS Windows FTP folders.  However, I can't connect to a client of the Terminal Services by transferring port 3389.  Is there a way to connect to the local LAN after scoring in the VPN connection.  I can connect to sites HTTP/HTTPS regulars and more than another type of connectiins, just not my own local resources.

  Thanks in advance... JS

  Happy to help, for what it's worth. Please mark question as answered if it is indeed and rate if the response is useful.

• Y560P card number: sleep mode and headset to the connected socket

  I searched the forum as much as I could and did not find this issue to be considered.

  So, sometimes I listen to music with headphones or even after a Skype call, I leave the connected headphones. If I put the laptop to sleep and wake it back up, unplug the headphones will not return my sound setting to speakers; I can't hear any sound if I plug the headphones in the back.

  I tried to connect and the new: no change. I tried to disable and re-enable "Realtek High Definition Audio" in the Device Manager: no change. Uninstall and reinstall it wouldn't be a good solution if it had to be done all the time. The only thing that it returns to normal is turning works again... typical I.T. solution. Is there a driver update to solve this problem?

  Speaking of driver updates, I guess that I can't find any BIOS update or updates to driver for the ideaPad due to the recall of Sandy Bridge?

  UPDATE: sorry... found the lenovo support site area sub consumer that is different from the IBM one... Argh...

  judge that?

• I can't communicate with a parser to network through the connection to the local network.

  Have a USB-ETHERNET connection to a network Agilent Analyzer.   I ping the instrument with the cmd prompt.   But I continue to get stuck to the implementation of a network via MAX connection or try to connect through connections Labview VISA.    I get the error "insufficient location information or the device or resource is not present in the system.

  
  

• Blur and expanded text and icons after the connection with Windows vista

  I have windows vista and when I turn on the laptop, the text and icons on the Welcome screen are normal, but after registration on the text and icons become slightly enlarged and fuzzy.  How can I get it back to normal?

  Hello

  There are a number of things to try:

  try going to your graphic card manufacturers site or computer and are looking for the driver download section

  Search your computer or graphics card model number based on what you have and download and install the latest graphics drivers for vista

  then try to make the screen of solution of problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-screen-resolution

  Change the screen resolution

  __________________________________________________________

  or try a restore of the system before this happened

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• T42 - stop and restart after the connection

  My T42, running on Windows XP, suddenly stops right after the connection and while the hotkeys on the loading screen.

  A message in white letters on a blue screen starts like this:

  "A problem has been detected and windows has been suthdown to prvent from damage to your computer.

  IRQL_NOT_LES_OR_EQUAL

  If this is the first time you've seen this stop error screen, restart your computer. "If this screen appears again, follow these steps:

  And the product message points to check any new hardware or software installation. I have not recently installed a software or hardware, so I'm a little lost on how to proceed from here.

  No clue on what could be the problem or any recommendation, short doing a full recovery from a recent backup?

  Any help will be much appreciated. Thenks.

  = UPDATE =.

  After running a few tests using the blue Access IBM button and PC Doctor 2.0 running, memory tests have shown the following results:

  Fast memory - all sockets - failed

  Fast memory - Support 1 - spent

  Fast memory - take 2 - failed

  This seems to indicate that one of the two memory is faulty. This hypothesis is correct?

  If so, what should be the next step? My laptop is out of warranty. I should bring it to a repair shop, or could I order the replacement and install it myself easily?

  I am not versed in repairs to equipment and feel a bit discouraged to start to mess with storage media...

  Any advice, please?

  Thank you

  It is probably a faulty stick of RAM in the second location rather than the power socket. Best bet is to remove the module RAM then see how it goes.

  Second is really easy to access. It is under the laptop - there is a small door in the middle of the base set with a single screw. Remove the screws and remove the door to expose the RAM module. Pull the wire staples on the outside of the restraint SODIMM socket and the RAM module should appear and then remove. Replace the cover and try the laptop again.

  IF you must replace the T42 uses to off the shelf of a DDR SO-DIMM, PC2700 speed RAM - needs. Will take up to a 1 GB module in each socket. First is harder to do because he must remove the keyboard to get home. It is only 4 screws but can be a bit tedious for a novice.

  Edit: The instructions for IBM appropriate here: http://www-307.ibm.com/pc/support/site.wss/MIGR-46513.html

• After upgrading from windows and reboot "diagnose the connection problem" rises and won't let me use windows until the removal of updates

  diagnose the connection problem

  You can try to uninstall the update 974455 that came out last Tuesday, removing it seems to have resolved other

• Color LaserJet MFP M277 dw Pro: Setup disk gives an error and stops before the connection to the printer

  Hello

  I try to install the printer 'Color LaserJet MFP M277 dw Pro'.
  By inserting the disc into the phase "installation preparation" is 96% and then stops and gives me the error.
  I use Windows XP SP3. It is always installed, but physically disconnected another printer hp (hp 2050).
  (I tried both to disable the antivirus that reduce to a minimal install, but the problem persists).
  Thank you

  Response thanks a lot.
  In the meantime, I contacted the Support of the Italy
  Who suggested that I try to update the driver.
  I downloaded the file "HP_LaserJet_M277_PCL6_Legacy_Print_Driver_14295".
  Automatic extraction and I launched and everything seems to work.
  (I still try to scan and fax if they work).
  Thank you very much.
  Thanks to your colleague Michelle with whom I chatted.
  Contact thank you for the support of Milan that I don't know the name.
  So, I can communicate the solution found.

• How can I prevent the shutdown task scheduler engine, get the new display detected to work and avoid receiving the message "Internet Explorer has encountered a problem and stop"? __

  My laptop is a Dell Inspiron 1520, running Windows Vista Home Edition Premium and Internet Explorer 9.  My extra monitor is a Sharp Aquos LED HD - TV, the model LC-46LE700UN.  I've been using a VGA cable to me onnecter the laptop and TV.

  The laptop seems to operate normally when not connect to the TV.

  As soon as the VGA cable is connected to the laptop (without being connected to the TV), the following message appears:

  'Microsoft Windows - Task Scheduler engine has stopped working.  A problem caused the blocking of the program works correctly.  Windows will close the program and notify you if a solution is found. »

  When initially, I connected the laptop to TV, "new display detected" was automatically acti EV.  Soon, it was activated is no longer automatically.  I was able to activate manually using Windows Mobility Center during automatic activation failed initially but now Windows Mobility Center no longer detects the new view.

  Using Fn + F8, I can view the image on the laptop or TV, but not both simultaneously.

  The message "Internet Explorer has encountered a problem and stop" appears intermittently, but I can still make internet sites and show the content after the message.

  I have download software, myp2p.eu, a site for watching TV programs "streaming", including PPStream, Sopcast, Live, Stream Torrent Sina, a Swarm, TVAnts, UUSee, VGO and Veetle player and canceled downloads for PPL (who failed an integrity check), PPMate (corrupted) and (blocked) TVKoo.

  Norton Security quarantined the installer of UUSee, indicating that it was a high risk of program with many users.

  To a computer repair shop and using a different additional display flat screen, I could not duplicate the problems yesterday (4 October 2010), when the "new detected display" has been activated automatically, and I could see the photo or the other and both screens.

  I tried to restore the system to a date (on the list) before when the problems occurred first - failure of the restoration of the system.  I tried to use scandisk, but received no indication that he had performed and corrected all errors found after restarting Windows.  I looked at responses from forum, the display setting and the new display detected support literature.

  How can I avoid these problems?  Help!

  Hello

  Restoring the system end up with any error message?

  This could also happen if one of the substantive programmes is in conflict with the proper functioning of your computer. To troubleshoot error messages and other issues,
  You can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Steps-
  1 log on to the computer using an account with administrator rights
  2. click on start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue
  3. on the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)
  4. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all

  Note: Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services.
  If you disable these services, you can permanently delete all restore points. Do not do this if you want to use with existing restore points system restore utility

  See this article-
  http://support.Microsoft.com/kb/929135

  This should solve your problem.

  -Robert

• iPhone 6 more issues activation and network on the latest iOS 9.3.2

  I have an iPhone 6 it is having problems with Activation and networking connectivity. I activated via iTunes and updated to the latest iOS 9.3.2 this morning. The phone remain active for a period of time and then come back to need activation.

  Using WiFi it is full bars but no connection. I'm typing this from my iPad on the same WiFi connection, so not the network. If I turn off WiFi and cell there still no connection. The phone will receive calls (even when stuck in the activation state) and can make calls after you have enabled from iTunes.  She was released a couple of times, but always the same question.

  I tried to erase and reload from iTunes to the top, but the restore function requires that find my iPhone service shut down on the phone and this step requires access to complete network.

  Try the following steps:

  • Try connecting your device to your computer and launch iTunes. Choose your device and click on summary > update.
  • If this does not work, make sure you have the latest version of iTunes installed on your computer and restart your computer.
  • When it restarts load iTunes and try to select your device and click on summary > update again.
  • If this does not work, it's time to try a restore. Press and hold the sleep/wake and home buttons on your iPad or your iPhone until iTunes gives you the option to restore your device.
  • When it's over, you can restore a backup, and you should be good to go with 9.3 running iOS.

• Volume and networks from the Notification bar icons

  My review of Volume and the networks have been removed from my right side of my Dell notification bar. I went to the taskbar and the Start Menu, in re properties - click on the boxes, but it wont let me click on one of the people, although the Power button and clock are selected. How do I return these icons?

  Hello

  1 Please reboot nothing so interfere with this process.

  Click with the right button on Taskbar - Properties - tab Notification area - check box Volume - if it is grayed out
  Then, use this link. (Ditto for power, clock and network.)

  How to enable or disable the system tray in Vista icons (there are several methods
  and you can to use them all).
  http://www.Vistax64.com/tutorials/106787-notification-area-system-icons.html

  If necessary: a Mr Fixit

  System icons do not appear in the notification area in Windows Vista or in Windows 7 until you
  Restart the computer
  http://support.Microsoft.com/default.aspx/KB/945011

  I hope this helps.