HP 15F009wm SM Bus driver issues in Windows 7 Downgrade

Similar Questions

• Y510p Trackpad driver issues on Windows 7

  I recently bought a Lenovo Y510p. Soon after receiving it, I wiped Windows 8 and installed Windows 7. I downloaded all the Windows 7 required drivers on the Lenovo support site and install without any problems. The problem I have is that most of the time the driver for the trackpad momentum seems to have issues. Device Manager acknowledges the mouse as a generic PS/2 mouse and the options of the momentum, under control panel > mouse is not CSA listed at all.

  I found a temporary solution to the problem. Uninstalling the drivers through the Device Manager, reboot, then install drivers the momentum of the Lenovo site, then reboot, I was able to get the mouse appears in the momentum Control Panel, where I could finally set my parameters. However, after my next reboot, the mouse was absent from the Panel momentum once more, and now I'm at square. I tried the solution that had previously worked, but I got no results.

  Anyone has any ideas or similar problems that they resolved?

  JacobT14 wrote:
  Altogether. First of all, I used http://mobilesupport.lenovo.com/us/en/downloads/ds035849 , this one, but noticed that also contained the Synaptics driver. So I downloaded this a http://www.station-drivers.com/index.php/downloads/Drivers/Elan/Elan-TouchPad-Drivers-Version-11.10... on the recommendation of a thread, I found somewhere (could be Lenovo forums, but I do not quite remember). You use the latter driver, I was able to recognize the trackpad once, but then, as I said, after I rebooted, it was gone.

  When you install the driver of Lenovo, you uncheck "install Synaptics... » ? Then install the expanded driver located in the C:\drivers\ folder...?

• Bus driver SM with yellow mark after installation of Windows XP Pro

  Finally, I have windows xp pro loaded. But in Manager device theres a yellow mark sm bus driver. Searching the forum I seem to have fould to her in the video driver ATI pack. But when the driver is loaded it messes up windows so it does not start.

  Can anyone help?

  Paul

  Hello

  I am reading other threads and it seems that you have a laptop Satellite Pro A60.
  What can I say you installed the OS manually and in my opinion a simple driver is missing
  Have you tried to install the infrared driver of the European driver Toshiba page?
  It may be a key

  In any case, before you start the manual installation of the OS, you must read the Installation Instructions. You will find all drivers that must be installed and the proper installation order.

  Please check this document and follow the guidelines

• Audio loss. UAA Bus Driver reads Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39). All the patches?

  Audio loss.  Device Manager indicates Microsoft UAA Bus Driver as: "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) ».  Tried to update driver and restore without success.  Tried the program of "Fix - It", which has identified an error with the sound system, but said that he could not fix it.  Restored to an earlier date but still what system did not go.  Tried to uninstall and reinstall the driver.  Uninstall was successful but reinstall it read that the hdaubus file does not exist.  I'm a computer dunce.  Any help out there?

  Hi BarbaraWolfe,
   

  There are many causes of Code 39 errors:

  • A required device driver is missing.
  • A required binary file is corrupted.
  • There is a problem with the file I/O process.
  • A driver that refers to an entry point in another binary file cannot load.
  Re-install the driver by downloading it from the link given:
   
  Universal Audio Architecture (UAA) High Definition Audio class driver version 1. 0a available for Windows XP, Windows Server 2003, and Windows 2000
  Additional reference on:

  Explanation of error codes generated by Device Manager in Windows XP Professional

  Check if that helps.

• Equium L40 - 10Z - Microsoft UAA for High Definition Audio bus driver need

  OK, this is what s up. I uninstalled Vista of the laptop and installed Windows XP Professional (5.1, Build 2600) Service Pack 2. All the drivers I installed works fine except my audio driver. There is no sound.

  I installed Realtek several times and it installs ok then restart to take effect, but when I restart there is still no sound. Driver installed is listed in Add/Remove programs. I tried for almost a week now to fix this problem and nothing happen.

  The pilot was MICROSOFT UAA BUS DRIVER for HIGH DEFINITION AUDIO with a yellow (!) next to it. When I tried open Realtek he said EQ failed or Summit and s there is a sound beep sound from the laptop.

  Toshiba virtual sound doesn t work as well. I accidentally uninstalled the driver and now it says device PCI and tells me to insert the disk MICROSOFT UAA BUS DRIVER for HIGH DEFINITION AUDIO but I n t I.

  It s been driven crazy and I don't know what to do.
  Please help me!

  Hello

  first of all, make sure that you have installed all the important windows updates. All the updates on your system? Ok.

  Please visit the www.realtek.com site and download the latest driver for realtek HD sound cards. This driver WORKS 100% because I had a similar problem and after I installed the authentic realtek drivers, I had no problem with the sound.

  Hope this works for you, too.

  Welcome them

• PCI bus driver not installed

  I have a PC Hp laptop model Hp 15-d017tu.

  I have a windows 7 64 bit after the new installation of windows and installation of all the drivers for the chipset, a PCI Bus driver has not been installed.

  Please tell me how I can install driver PCI.

  Concerning

  Sami zaoui

  Hello:

  If there is a device listed in the Device Manager, PCI should it probably this driver...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-126593-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 6622260 & sw_lang =

  If this isn't the driver you need, I'll need the hardware ID the device requiring the driver.

  Go to Device Manager and click on the device requiring the driver.

  Then click on the Details tab in the upper part of the device window.

  Now, you see a drop-down list of property and it is set by default to the Description of the unit.

  On this list and select the item named hardware ID

  After the first string of characters you see in the window that begin with PCI\VEN.

• Bus driver SM for equium a60-692

  Hello

  I reformatted my hard drive and reinstalled windows xp professional, but miss me the SM Bus driver. Is it possible that you could tell me where I can get one please.

  I tried looking on the net and check the updates of windows, but nothing may be available. There are a lot of drivers on the net and im not sure if they are all compatible. any help would be appreciated.

  Concerning

  Ashley

  Hi Ashley,
  You must install the display driver.
  (ati chipset + driver V6.14.10.6430 to display)
  Have a look here: http://www.iamnotageek.com/a/114-p1.php
  Good bye

• Iconia Tab W510 driver issues (WiFi)

  Hey there,

  I am an Iconia Tab W510. Very nice, works well - I thought. I have the version with 32 GB. It is a device of demonstration, since it is the last of them was the store. Just like I wanted a Win8 clean and fresh installation I did full recovery for a long time through these 4 discs.

  He worked in nice, but gave me an error as it began after full recovery. I guess it was on this custom in the OEM package software. The error message was "C:\Windows\System32\OEM\AlaunchX\AlaunchX.exe a referral was returned by the server.

  This message is not the problem, but it may be important to find a solution.

  After clicking 'OK' - as if I had another choice -the normal startup tab and I can use it. What I saw then was that, under the leadership of the unit, there are four devices without drivers. I downloaded the package of more recent (and updated the BIOS) driver from the acer homepage. The version of the driver package was 3.01 and the BIOS version is 2.00.

  I installed the update of the BIOS at the beginning that surprisingly installed all the drivers missing. The broadcom drivers have been installed, there's no any errors during installation, but both, the SDIO of Broadcom 802.11abgn Wireless adapter and the Bus driver Broadcom series on UART Bus enumerator do not work properly, because they are marked in the Device Manager with yellow warning sign. The message for two devices in Device Manager says: "this device cannot start (Code 10)".

  I had a white night that without being able to find the solution. With the two drivers not working not properly the WiFi does not work, of course. And without a working WiFi this tab is... Well it's pretty useless to me. I read a lot of problems with this tab and its WiFi behavior but apparently not that somebody had the problem that I described here.

  If anyone have a solution for this, I would be very grateful. Since it is a nice tablet, I really want to keep it, but which is not not WiFi works its really useless. So: any ideas how to fix this mess?

  Greetings

  I've chatted with acer yesterday and told them what I've done. They came to the conclusion that the WiFi module appears broken, so I should send him my tab for repair.

  The last thing I tried was install Windows Pro 8.1 and using drivers Win 8.1 from the support home page. He gave me the same error with two Broadcom devices once again, so it may not be a corrupted driver.

• No Audio device and Audio HDA Bus Driver Error Win XP SP3

  Hello

  I'm running a put together computer, with Windows XP SP3. I've recently accidentally got rid of my sound on my computer, eliminating the bad program in Add/Remove programs. I know that my computer is running Intel (r) 82801 AA AC 97 Audio Control. So I went to the thought of their site, I had deleted the drivers and audio devices. I downloaded the current driver, but this has not fixed the problem even with an update. So I went hunting online and found this link http://www.youtube.com/watch?v=9idzHNWZLP0

  , thinking maybe that would help me even though I am not a user real tek (have intel of course). But he said that it is compatible with windows xp. I tried downlaoding it and got the error: "could not complete the installation: missing Audio HDA Bus driver.

  So now, it seemed to me, I had not only a mistake, but two. I tried to download a driver of Bus HDA, but this failed. I tried to look in the Device Manager to see if there was a red or yellow marker next to my audio devices and maybe they needed to be reinstalled. Showing a problem there, he said nothing everythign was working properly. I tried to use Soundmax audio driver as well, but who was also discussed with the bus driver error. I also went to http://noaudiodevice.com , and these solutions do not work either because I was not faced with a problem of yellow or red marker. I also did this off stupidly deletling the bad thing no one updated.

  I'm almost at a loss at this point and was way over my head to start.
  I could really use some help. I know that my computer when I had one month ago second hand but wiped off, had run soundmax. If you need more information about my computer or screen shots please let me know. I looked at the subjects here, and none seem to adapt to this situation for me.

  Did you get the specific drivers for your motherboard?
  If this isn't the case, remember to search the downloads specific to what you have.

  You can try a system restore: http://support.microsoft.com/kb/306084

• His driver error - HDA bus driver is required and not found

  Original title: I downloaded the audio driver for windows xp proffesional and when I install it it say had bus driver is required and not found what I need to do. Please can u help

  the model of my Tower is hp compaq dc7800 cmt pc while using the software windows xp proffesional. downloaded the drivers from the hp site yet it say HDA IS REQUIRED AND not FOUND

  Hello

  Try these steps and check if that helps:

  a. Click Start, click Control Panel and then double-click System.

  b. click on the Hardware tab.

  c. expand sound, video and game controllers.

  d. double-click the sound card and then click on the driver tab.

  e. click on uninstall the driver.

  f. follow the Hardware Update Wizard to update the sound card driver.

  Download and install the drivers from the links: ADI High-Definition (HD) Audio Driver for Microsoft Windows XP and 2000: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=3459240&prodNameId=3459243&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=vc-58778-1

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=3459243&prodTypeId=12454&prodSeriesId=3459240&swLang=13&TaskID=135&swEnvOID=1093#113165

• Required, not found HDA Audio Bus driver. XP SP3

  I run a computer custom made with Windows XP SP3. Under other devices with a yellow question mark is multimedia Audio Controller, through the PNP ID, I discovered it was Analog Devices ADI 198 x integrated Audio. I found a driver (not sure if it was good) and when I went to install the error "HDA Audio Bus Driver required and not found do not" pop up. There is no Bus Microsoft UAA HDA Audio driver also under system devices. I appreciate all the help you give me. It feels like I tried all the solutions, but I'm open for anything at this point. Thank you!

  I appreciate your help theplectrum! I went to the Intel Web site to find a driver of Ethernet controller, so I ran the driver update utility. He found a driver of sound for me as well. I installed and rebooted and now I have sound!

• Found New Hardware "Microsoft UAA Bus Driver for High Definition Audio".

  Hello, here is the whole of it.  I recently bought a card XFX ATi Radeon HD 4650 1 GB DDR2 video AGP8x.  I uninstalled my old graphics card driver and took out my old nvidia card.  I threw in the radeon and started my computer.  Now it starts windows and the bubble 'new hardware found' in the bar tasks appear, 1 saying he concluded a 'video something.' Then a 2nd bubble appears who says: "Microsoft UAA Bus Driver for High Definition Audio" Word for Word. As this bubble appears, my computer slows down as if the RAM has been withdrawn, and after about 30 seconds, it is a gel closely.  I can't install my drivers for the radeon and I have to turn off manually my computer is not responding.

  Now, I have tried

  • Install the drivers before I put in the graphics card
  • Research on the XFX site for possible solutions
  • Turn off the "found new hardware found" I don't not succsesfully.
  I also tried many other things, but none worked.  If anyone has a solution to this answer please problem.  All I want is my graphics card to work.  Thank you

  I had exactly the same problem.  The instructions on the following link solves the problem.
  http://www.boredsysadmin.com/search/?q=UAA+bus+driver+for+high+definition+audio&search.x=42&search.y=8

  Then, I came across a problem where pilots would not charge because the card was not recognized.  This has been fixed with this patch.
  http://support.AMD.com/us/KbArticles/pages/CatalystAGPHotfix.aspx

• OS not found on the c: drive, cannot start windows

  Today, I tried to restart my laptop and all of a sudden, they won't let me restart. It keep telling me that I can't or my hard drive is too small. and I tried all the option, even tried to restore my c: drive, but then he told me that I have to choose: full system restore:.

  However, full system restore wasn't in one of my options and after that I dropped to restart the laptop want to just start over my windows, but then I can't do more because in the Windows error recovery just an option that is recovery tools, it doesn't have the choice as boot the system normally.

  So now I can't enter to windows or restart my computer, how do I get into my windows again? Help, please. :(

  Hello

  
  1. What is the exact error message you get?
  
  Method 1: I suggest you try the steps from the following link

  Windows Vista or Windows 7 unbootable, and the Startup Repair tool does not resolve the problem
  http://support.Microsoft.com/kb/934540

  Method 2: go to the BIOS (Basic Input Output system) Setup, & change the switch setting between AHCI (Advanced Host Controller Interface) and IDE (Integrated Drive Electronics), SATA (Serial Advanced Technology Attachment) and the drive controller is restarted. If it solves your problem, the driver for the HARD disk (HDD) is corrupted.

  IMPORTANT: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Method 3: Your hard drive is damaged to the point that it cannot even recognize that Vista has been installed on it. If you have a Windows Vista installation disc, you can try running chkdsk to fix the HARD disk; you need to restart (boot) your computer using the installation disc.

  a. Insert the installation disc and restart your computer.
  b. click the Start button, click the arrow next to the button lock and then click on restart.
  c. If prompted, press any key to start Windows from the installation disc.

  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see check the link for the BIOS: frequently asked questions: http://windows.microsoft.com/en-us/windows-vista/BIOS-frequently-asked-questions

  d. choose your language settings, and then click Next.
  e. click on repair your computer.
  f. Select the operating system you want to repair, and then click Next.
  g. in the System Recovery Options menu, click command prompt
  h. type chkdsk /f / r and press ENTER.
  
  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

  This will perform a disk check and perhaps recover the system. CHKDSK can repair problems related to bad sectors, lost clusters, reticulate files and directory errors

   

  Method 4: I suggest you run /ScanOs, /FixBoot commands from following link:

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows
  http://support.Microsoft.com/kb/927392

• upgrade to driver issues made worse?

  just downloaded and updated my nvidia card driver who ran over a pilot 175 original giving a rating of 3.6 thought I would improve matters by upgrading to the latest version of the driver (for the 9000 series) a pilot to 266 which, to my great dismay now shows a representation office of3.5 (4.7 gaming performance remains as before) , I'm running flight simulatorX and unless I keep video recordings of each very short flight and delete it before I try another recording does work not beyond start-up or watch a crazy sequence ending in a crash in a few seconds.i am running vista SP2 32 bits of the system on pc medion with 3 GB ram processor intel quadcore with 1 TB of capacity of the computer I thought must be adequate-i am at a bit of a loss to know where the deficiency lies - all system performance controls are ok only ever connected problems are when he's not wake mode 'sleep' occasionally, but I simply restart - no problem with the original driver .the has been removed in the bonus process, so I can't go even if I wanted

  Hello

  There is a small difference between 3.5 and 3.6, and your card is probably work
  at the edge of this difference. You probably won't see any difference at all.

  You can go back to an older driver from Nvidia Site - check with their support.
  their documentation online and drivers and ask in the forums of Nvidia. Although I'd
  not back in this case.

  NVIDIA - drivers - use OPTION 1 to manually enter your info driver to get the most recent drivers.
  http://www.nvidia.com/download/index.aspx?lang=en-us

  NVIDIA Support - check with the support that she might be a known issue
  http://www.nvidia.com/page/support.html

  NVIDIA forums - also check for the forums it might be a known issue or others likely to have
  http://forums.nvidia.com/

  ================================================================

  This is a convenience store faily comprehensive overall performance which may help.

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

• Where is the "PCMCIA Bus driver" and how to uninstall it?

  The menu Tools and Information on the performance said that "these drivers are causing Windows to resume slowly"-

  Name: PCMCIA Bus driver

  File name: pcmcia.sys

  Feature: Texas Instruments controller CardBus PCI - 8 x 12/7 x 12/6 x 12

  Other posts on this forum, I understand that it is safe to uninstall this driver if it is not in use.  Unfortunately, I can't find.  I looked in Device Manager (there are two other devices Texas Instruments listed - or one has the correct device name).  I also looked in programs and features and menu of start-up of sysconfig with no luck.

  My computer was crashing regularly about 10 minutes after waking up from hibernation.  My hope is that this driver uninstall will fix the problem.  Any help would be greatly appreciated.

  It seems that the "Texas Instruments PCIxx12 Integrated FlashMedia Controller" device is the device you are looking for (the first two digits in 8 x 12, 7 x 12 and 6 x 12' is reduced to a "xx12' in the name of the device for simplicity). Try to disable it and see if your problem is solved.

  Note: This device looks like it controls a card reader. It is a decive integrated on your CPU, where the floppy drive which reads flash memory cards (for example: SD card, Memory Stick, xD card, etc.).

  Rifdhan

  If this is your answer, click on "Mark as answer" below. If it's useful, click on "Mark as useful" on the left.