HP Compaq dc7700 SFF - Ethernet controller not detected

Similar Questions

• HP compaq 6530 b ethernet does not work

  I have a laptop hp compaq 6530 b. A few days ago, I installed it for the first time Windows, in particular Windows7 Ultimate 64 bit (I used Ubuntu). Since the ethernet connection installation does not work (so that wireless gives no problem) although I installed all drivers HP hp websites...

  Can someone help me?

  Thank you

  Ciao,.

  You can go back and enable this setting. I assumed that you had installed the drivers.

  LAN save mode power turns off your wired ethernet card to save battery when it is not connected to an ethernet cable.

  People get alarmed when they don't see the wired ethernet controller, which is listed in Device Manager when there is no cable connected, and they think their wired network adapter is defective.

  When you disable the LAN power save setting, always wired ethernet controller is on and remains visible in the Device Manager if a cable is connected.

  Now in regards to the pilot, you must...

  It can be found on the link below.  Select windows 7 x 64 driver file.

  http://www.Broadcom.com/support/ethernet_nic/netxtreme_server.php

  Paul

• HP Compaq dc7700 SFF PC can be upgraded to support a 2.66 GHz Intel Core2Duo (E7300) processor?

  My HP Compaq dc7700 desktop PC small form factor is equipped with a processor replacement of Intel Core2Duo 2.66 GHz (E7300), Stepping/CPU ID 10676, but I now have a start-up error message: "1801 - Microcode patch error.»  Missing or not valid processor updated Microcode.  "Please contact Hewlett - Packard Company for a new firmware update to support the new processor Stepping.

  (The computer start in pressing 'F1', but performance deteriorated due to invalid processor Microcode Update).

  I sent to HP, but have yet to receive an answer.   (They may have bigger problems right now!)

  The HP documentation for the dc7700 is ambiguous about whether if an E7300 processor would be sustained.  In this regard, the documentation recommends against editing processors more than 95W, but the E7300 is only a 65W processor (exactly the same as the original processor E6300).

  I've updated the PC system BIOS (786E1, Rev 1.16, the most recent available on the HP relevant support Web page):

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en & cc = us & prodNameId = 3232108 &...

  "(mais malheureusement, il semble que Rev 1.16 n'inclut pas une mise à jour de Microcode valide pour le processeur E7300)."

  It seems that I may need to wait and hope that HP will issue a valid and new Update Microcode for the E7300 dc7700 support page.  (With luck, the update of firmware would be included in an update of the BIOS which can be implemented through the windows, not via a legacy floppy!) 

  (I note that Intel provides an easy firmware update, but it is not easy for those who are running a Linux Enterprise operating system.  I am running Windows Vista Business 64-bit).

  This is my first post.  Thanks for all the tips on the problem that I outlined above.

  Thank you Paul and Frank,

  The evidence you presented against compatibility has begun to address substantial.

  Furthermore, it is probably not conclusive in itself, but Intel motherboards with a chipset Q965 (at least the names of the Council containing the string '965') also do not appear to support beyond E6700 processors...

  http://processormatch.Intel.com/COMPDB/SearchResult.aspx?BoardName=DG965SS

  I'd be happy to call my request 'resolved' - has answered in the negative.   Thanks again and well done! to each of you.

  With gratitude,

  Robert...

• HP Compaq d530 SFF DIMMs do not recognize. Windows Vista Home Premium 32 bit - BIOS version 02.44

  Hello HP community!

  I recently got a HP Compaq d530 SFF of the company, where I had my work experience.

  Fortunately, I took their offer and took the PC at home, everything was going well until I bought myself some new DIMM from ebuyer.com.

  I again for a fact, the computer must DDR 333 MHz, PC2700 and it must be in DIMM format, so I went and bought 3x1Go modules. A few days later they arrived and I have them inserted in the computer, ensuring that two DIMMs was in blue locations and others (I wanted to keep a 256 MB module to) in the black sites.

  I have re-inserted power cable and tried to boot the PC, he showed me a BIOS message, showing that the amount of memory has changed, since the last boot. Once the configuration is presented, he acknowledged only the 256 MB module. I then turned off the computer, and then remove the 256 MB module, to see what would happen. So, I restarted the PC, and it gave me an error (not shown) tone. To which I then tried (needles) each DIMM different to see if one of them was vice. They are all gave me the same error tone. Since then, I've been running Windows Vista Home Premium, with 1 GB (4x256MB DIMM).

  Maybe someone has a suggestion how to fix this?

  I've already updated the version of the BIOS at 02.44 (later I could find).

  Thanks in advance!

  Yours sincerely Simon Cahill

  Beatsleigher,

  Not all memory is the same, even when picking PC2700. Did you buy non ECC?

  Here is a guide on the configuration of the memory for the D530SSF

• Compaq dc7700 sff: motherboards latest include the compaq dc7700 sff case?

  I want to use the case of an old dc7700 sff, but the layout of the Panel back looks like it is the inverse of all the motherboards I've found. Is there any motherboards that support DDR3 RAM and have at least three connectors SATA (SATA 3 preference) that will be adapted to this case (PCI ports on the left instead of right of ports)?

  Hello:

  Unfortunately, there is not.

  The dc7700 was the last model that used the case that has also been used d530, dc7100, dc7600.

  When the dc7800 came out, they used a completely different case, which was also used on the dc7900.

  Then the case was changed again when the 8xxx models Elite have been introduced.

  The first business office of HP in this class that came with sata ports 3 was the 8200 Elite SFF/CMT.

• Ethernet controller not found in Vista

  I've just intsalled my first VM Vista and for some reason, the virtual machine does not connect to the internet.  In Device Manager, I found that there is no such thing as the Ethernet controller driver.  I tried to reinstall the VMware tools, but it does not solve the problem.  VMware tools fails also try to install the SCSI driver. Here's the vmx file.  Any help is appreciated.

  . Encoding = "windows-1252".

  config.version = '8 '.

  virtualHW.version = "7".

  numvcpus = '2 '.

  scsi0. Present = 'TRUE '.

  memsize = "2048".

  ide0:0. Present = 'TRUE '.

  ide0:0. FileName = "Vista.vmdk".

  IDE1:0. Present = 'TRUE '.

  IDE1:0. AutoDetect = 'TRUE '.

  IDE1:0. DeviceType = "cdrom-image".

  floppy0.startConnected = "FALSE".

  floppy0. AutoDetect = 'TRUE '.

  ethernet0. Present = 'TRUE '.

  ethernet0. ConnectionType = "bridged".

  ethernet0.wakeOnPcktRcv = "FALSE".

  USB. Present = 'TRUE '.

  EHCI. Present = 'TRUE '.

  Sound.Present = 'TRUE '.

  sound.fileName = "-1".

  Sound.AutoDetect = "TRUE".

  MKS. Enable3D = 'TRUE '.

  pciBridge0.present = 'TRUE '.

  pciBridge4.present = 'TRUE '.

  pciBridge4.virtualDev = "pcieRootPort"

  pciBridge4.functions = '8 '.

  pciBridge5.present = 'TRUE '.

  pciBridge5.virtualDev = "pcieRootPort"

  pciBridge5.functions = '8 '.

  pciBridge6.present = 'TRUE '.

  pciBridge6.virtualDev = "pcieRootPort"

  pciBridge6.functions = '8 '.

  pciBridge7.present = 'TRUE '.

  pciBridge7.virtualDev = "pcieRootPort"

  pciBridge7.functions = '8 '.

  vmci0. Present = 'TRUE '.

  roamingVM.exitBehavior = 'go '.

  displayName = "Vista".

  guestOS = "winxppro.

  NVRAM = "Vista.nvram."

  virtualHW.productCompatibility = "hosted".

  FT.secondary0.enabled = 'TRUE '.

  Tools.Upgrade.Policy = "useGlobal".

  extendedConfigFile = "Vista.vmxf".

  floppy0. FileName = "a":

  IDE1:0.startConnected = "FALSE".

  ethernet0. AddressType = 'generated '.

  tools.syncTime = "TRUE".

  UUID. Location = "56 4 d 30 c3 a2 6 c 81 ca - bd fd ca fe c0 13 45 22.

  UUID. BIOS = "56 4 d 30 c3 a2 6 c 81 ca - bd fd ca fe c0 13 45 22.

  debugStub.winOffsets.version = '1 '.

  ide0:0. Redo = «»

  vmotion.checkpointFBSize = "134217728.

  pciBridge0.pciSlotNumber = "17".

  pciBridge4.pciSlotNumber = "21".

  pciBridge5.pciSlotNumber = "22".

  pciBridge6.pciSlotNumber = "23".

  pciBridge7.pciSlotNumber = "24".

  scsi0.pciSlotNumber = "16".

  usb.pciSlotNumber = "32".

  ethernet0.pciSlotNumber = "33".

  sound.pciSlotNumber = "34".

  ehci.pciSlotNumber = "35".

  vmci0.pciSlotNumber = '36 '.

  USB:0. Present = 'TRUE '.

  USB:1.present = 'TRUE '.

  ethernet0.generatedAddress = "00: 0C: 29:13:45:22.

  ethernet0.generatedAddressOffset = '0 '.

  vmci0.ID = "1698986863".

  USB:1.DeviceType = "hub".

  USB:0. DeviceType = "mouse".

  IDE1:0. FileName = "C:\Program Files (x 86) \VMware\VMware.

  debugStub.winOffsets.value = ' 0 x 88, 0 x 84, 0x18, 190 0 x, 0 x 174, 16, 0x22c, 0x1f0, 0 x 224, 0 20, 0 x 0, 18 x 18, 0 x 0, 20 x 24, 4.

  tools.remindInstall = "FALSE".

  checkpoint.vmState = «»

  ethernet0.linkStatePropagation.enable = 'TRUE '.

  No need to reboot your host between changes in the configuration file of comments.

  You do, however, need to have comments shut down/off voltage (only suspended not) to make changes to the file (whether you use the Workstation GUI or manual editing).  Verify that the changes you made still exist in the file.

• Laptop Compaq CQ58: LAN Ethernet does not work after the upgrade to windows 8.1

  After the upgrade of Windows 8 to 8.1, my Ethernet LAN is no longer in effect. Wireless LAN connectivity is OK. I run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I don't see a listed 8.1 for the LAN Ethernet driver.

  It seems that you encounter the same problem, I did when I ran the free preview of the W10. I had this error on the card reader.  I have no idea how to solve this problem.

  Is there is no ethernet controller needing drivers in Device Manager, then it is probably the realtek lan adapter that has the number 12 of the code, or it is part of the motherboard that controls the ethernet adapter.

  If you need Atheros bluetooth driver, then this is probably the one you need.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_127984_1

  Unfortunately, I won't be able to help you with question 12 code or ethernet.

  IMO, they are insoluble.

• POUVEZ HP COMPAQ DC7700 SFF CPU E6750 UPGRADE

  the site says he may spend up to e6700. so, I just want to know if e6750 can fit in. someone help me please.

  Hello:

  The E6750 will not work because it has a 1333 MHz FSB speed, and the greatest speed FSB that can handle the card mother/chipset in the dc7700 is 1066 MHz.

• Ethernet controller not installed on Windows 7

  I tried to create VMS on ESX 3.5 using the Windows 7 operating system, but it seems that the ether controller is not supported. You want to know how can I achieve this.

  I have not tried with 'Other' as an operating system, but have successfully created the x 86 and x 64, respectively using '32-bit Vista' and "Vista 64 bit" as an operating system

• DC7700 Converible minitour: HDD not detected, windows does not load

  Hi, I have this computer running Windows, but Isaw today it shows no disk system error. I replaced the cables, I ran the HP Vision Diagnostic test and saw that it shows errors in the extended SATA Firmware tests-, error code is 990518 and the failure code is 503. SATA seq check test displays error code 990161 and error code 502 parameters test not valid. SATA random performance test fails also to 1% as the other two and also 990161 and 502 times as codes respectively. Should I change the hard disk or there might be an error in the BIOS or the system itself? Thank you.

  Hello

  According the information that you posted in your other posts and this post, I suggest you replace the hard drive.

• DC7700 sff: HP Compaq dc7700 sff video updated to improve performance.

  
  

  Hello:

  I recommend the graphics card AMD HD 6450 profile low profile low supports.

  It is the optional card in the HP 8200 Elite SFF, which also has a P/S 240W.

• HP compaq dc7700 sff: Audio driver

  Need a driver to activate my integrated audio system.   Is there a solution.   I just rebooted.

  Hello

  No Audio driver for Windows 7. Please try Vista driver from following link:

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=3232108&swLangOid=8&swEnvOid=2096

  Kind regards.

• DC7700 SFF BIOS support

  My father has just bought a PC HP Compaq DC7700 SFF (Small Form Factor) used and refurbished and we get an error whenever the computer places.  It reads "BIOS ME Extension stopped Module.  I did some research on Google, and it seems that the error indicates that the BIOS and the BIOS Extension ME are out of sync, which means that their versions do not match.  We are a bit surprised, it was not addressed prior to packaging for resale upward, but nevertheless we are here.  The computer came with Windows 7 Home Premum 64 - Bit.  It is the source of the problems.  Everything I read says to use a BACK program called "FlashBin" to Flash the BIOS with the latest version.  Whenever we try to run the program, it errors saying incompatile architecture (he wants to x 86).  We tried other things is manually creating a BOOT partition on a USB Flash drive and try to run the program to start BACK, but it does not, saying no found BOOTMGR or something.  Another option I found is that the BIOS has a setting called something like "Flash BIOS update" and asked where to find the file. CD-ROM or USB.  When we put on the USB flash utility, BIOS indicates the key USB is corrupted or damaged.  This also happens when we just updated BIOS. BIN file on the USB key with nothing else.

  We are really lost here.  As I said, this is a factory refurbished PC and we would really like to get this annoying error message to go outside every time we start.  Can someone help me please?  Thank you!

  Hello:

  You can read some of the posts offered on reset the cmos on your PC.

  Reset the cmos works the same on the dc7700.

  http://h30499.www3.HP.com/T5/business-PCs-Compaq-Elite-Pro/me-error-on-Compaq-dc5800/TD-p/940477#.UvFtmemPK9I

  If you want to try the update the ME firmware suggestions, you must use the files to download on the dc7700 under section BIOS support page and I wouldn't update the firmware if you have to do in Windows for the same reason that you would not run an update of the BIOS under Windows.

  I hope that the reset cmos will work for you.

  I have never had this problem on any of my dc7xxx as PC, if unfortunately I won't be able to help you with specific measures to be taken regarding the update the firmware.

• Satellite L300 - how to install Ethernet controller?

  Hi all

  The other day I was cleaning up my computer (just uninstall unused and games programs and other things) and I accidentally uninstalled my ethernet controller.

  I restarted my computer and it came with a box saying install ethernet controller. So I click on this button and it said to put in the disc that came with the computer, but I do not have a disk, and so I clicked on another option that says "use another option to install this" so I clicked it, but then he said you must be connected to the internet. which is all just stupid because I can't connect because no ethernet controller not... So! My question is: what can I do to install it again, or whatever. I'm not that smart computer, as I don't know anything about any electronics inside the screen or something, I'm on of those people who knows how to change the wallpaper and installing a game, but that's all.

  Can I get a disk to the message box says to Toshiba? or perhaps a local store like Ricahrd Smith (Actaully his Di * ck smith, he said I can't have the complete word apparently his rough. haha) or something?

  Please help me. I am writing from an Internet café and I really don't like this part of town... lol. I'd rather be in the comfort of my own home and being on the internet there.

  Thanks for any help you can provide.

  Hello!

  To me it sounds like that, you have also uninstalled the driver of Ethernet controller and so after reboot, the message appears that you will install the Ethernet controller.

  However, you can download all the drivers for your laptop on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Maybe you can download the driver in the internet cafe or a friend who has the internet connection.

  More the laptop is not delivered with a recovery disk because you have to create this disc by yourself. If you start the Toshiba recovery disc creator you can create the recovery disk that contains an image of the factory settings. You can boot from that disk but it erase your entire HARD drive so always backup the files on the HARD disk before using it. It of pretty easy to use and only takes a few minutes.
  If you would like more information on the recovery disk, please consult your user manual!

  Good bye

• Ethernet controller - driver not installed - Compaq Presario

  Hello, I'm new here so be gentle

  I just bought second hand a Compaq Presario 6240EA, motherboard is a Compaq 07D0h.

  In the hardware - device manager, it says "Other devices" - Ethernet controller, with a big yellow question mark and an exclamation point.

  Details in the properties indicates the following: drivers for this device are not installed (Code 28)

  PCI\VEN_10DE & DEV_01C3 & SUBSYS_00A80E11 & REV_C2\3 & 13C0B0C5 & 0 & 20

  I find the HP and Compaq sites for driver downloads and downloaded all of the nVidia drivers available on the Compaq site, including any improvement in the situation.

  Is there somewhere else to look at, I'm at my wits end with this, any help would be appreciated.

  Thank you in advance.

  Hello CherylG

  Thank you, it worked, thank you very much for your help.

  I guess the answer was there, I just don't see it, I thank you once again.

  Take care