Similar Questions

• PlayBook of blackBerry Smartphones does not connect to the WiFi PRIV "hot spot"

  BlackBerry PB does not connect to the WiFi PRIV "hot spot". Implements immediately with an android tablet based - Hudl of Tesco UK - but the PB comes not to connect to the private. Reading through various bulletins and cannot find anything obvious that I missed. PB connects to the other wifi fine.

  Sorted. And so simple. Just changed PRIVATE WiFi "hot spot" to 5 GHz. thanks to Bruce using BlackBerry.

• iPad does not connect to the Wifi on the range 192.168.0. *.

  I have an iPad Mini (ME860BA) on os 9.3.1 that would not connect to my wifi at home.  He began to abandon their studies repeatedly a few months before and then just wouldn't connect at all.  It is on the os 9.3 so I upgraded to 9.3.1 but it did not help.  I was able to connect using a hotspot from my phone but no go on the real wifi. Sometimes it seems impossible to connect and others it seems to connect but without the wifi icon that appear (and internet access). All other devices connect to the House without exception (or question) - it's just my iPad.

  I followed every bit of advice I've found - turning wifi off & on, forgetting network, reset all the network settings, hard reboot, reboot normal, turning airplane mode turn off again, go up the brightness of the screen (odd) and finally I restored my router and the iPad to factory settings.  Nothing worked, so I took him to a store of Apple and waiting for the genius to see me I thought I would try to connect to the wifi and it went all right!  I felt a little silly to start with but they still took a look and said that he had 'something' bad, but they didn't know what.  Their best guess was that it was something to do with password authentication because they are client wifi has no password.  I returned home and disabled the security mode of the router - I have a Virgin Superhub running the 2.4 and 5 GHz primary wireless networks - no amount of adjusting the security modes (remove the password, make visible SSID, change of Protocol) makes all the difference.  However, knowing that it worked on wifi from Apple in the store, I was really puzzled.

  After ages bother with different parameters (especially in my router), I now know why it does not connect to home... My Virgin router to short on a range of address DHCP IP of 192.168. 0. * and my iPad suddenly won't connect unless the beach is 192.168. 1. * or higher.  (It connected OK for 2 years).  It took weeks to find this out, but at least now I can connect.  I turned on the wifi of comments because it uses the gamme.1.  Everything is good, connects the first time, every time!  I have not tried establishing a password (I was so happy, it connected I left because it was... well as I switch on the MAC filtering, for a little extra protection) I could try side password later and if it still connect, I'll update my post.

  My solution is very well when I'm at home but is not going to help if I get the iPad with me - it will be hit & miss if I can get the WiFi also.  Must be set correctly - I see no that it is hardware related, so there must be a bug in the software/firmware.

  Anyone having problems connecting to wifi can try the workaround network comments - at least it will get you.

  Is there a future fix for this?

  Re: iPad wifi suddenly does not save

  Change the range on the router you want to connect to.

• Mac does not connect to the wifi and keeps crashing

  My macbook pro (end 2013) will not connect to my wifi although each device only. Now he has slow veey hone and continues on crashing, doing simple things like a PDF of scrolling. It all started a week or two after the upgrade to OSX El Capitan

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• M177fw does not connect if the WiFi extender is activated

  Main WiFi router's CISCO E4200

  WiFi Extender is TP-LINK TL-WPA4220

  Printer is HP LaserJet MFP M177fw Pro

  Date of the firmware: 20130823

  Install Smart SW Version: 20/06/2013 1.0.13171.352

  Printer is in the same room as the CISCO router.  Extender is located in another part of the House.  Extension signal is low near the printer.  The Extender is turned off, the printer immediately connects to the WiFI network.  When the extension is enabled, the printer tries to connect several times and fails.  All computer iPhone, iPad, laptop and smart TV in room normally works with the CISCO and extension under voltage, but the HP printer does not work.  Is there something I can do to fix this?

  This has always been a problem with 2 AP make sure the router and the Extender are on different channels, like 1 & 6, 6 & 11, 1 & 11.   Where is the printer, set this AP to channel 1.  Try now.

• Troubleshooting-new HP with Windows 7 spectrum XT, does not connect to the WiFi at home?

  So I just got my brand new HP ENVY spectrum XT Ultrabook with Windows 7 Home Premium installed. 64 bit. I start it, everything works fine, except that when I connect to my WiFi at home. I tried to connect, entered my password, but it does not connect. Also tried the easy connection on the router. No luck. I checked my old laptop which runs on Windows Vista to see if WiFi worked always, and this is where it gets interesting. I was able to browse the internet and internet worked, but suddenly Windows informed me that "another computer uses the same IP address" and it stops my internet capabilities on my old laptop. I connected my cable ethernet on both computers, and it works for both computers when it is plugged. While that plugged, I discovered that I could create my own IP address, which I did on my old laptop and so far that seems to have solved the problem. However, my DESIRE is always not connecting to WiFi. Any advice?

  Hi ZachRhodes3,

  ·         You get the error message?

  Follow these methods.

  Method 1: Temporarily disable the security software .

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow step 7 the link to start the computer to a Normal startupmode.

  Method 3: Follow the steps in the article.

  Windows wireless and wired network connection problems

  5 steps: how to set up your network wireless home

  For reference:

  How can I troubleshoot network card?

  Wireless network card: frequently asked questions

• Centro does not connect to the synchronization with Windows/Palm HotSync

  My Centro ceased to sync with my Windows XP computer.  It just does not connect.  Did the soft reset, restart windows, etc.  No problem in Device Manager.

  The value of sync with outlook on the exchange server data.

  Same Centro and sync cable fine on the Linux machine using gnome-pilot and lines of development to access the same data exchange.

  Assuming that you can navigate through your windows machine.

  1. open Device Manager
  2. when your device is connected, you will see palm os handheld
  3. click straight and say to uninstall the driver
  4 disconnect your device and soft reset it
  5. reconnect the appliance and leave it to reinstall the driver

  This will force reinstall the driver and also tell us if there are errors with the driver.

  Message relates to: Centro (Sprint)

• My mac does not connect to the wifi unless I turn on the iphone

  My home wifi works great though I have my wifi enabled on my iPhone. But if I have the wifi turned on on my phone, free wifi does not work half the time, unless I wake up my iPhone. I do not use a personal hotspot, or any other type of phone wifi-centric. Just a normal modem and apple airport extreme router.

  My mac is a model of iMac end 2015 running El Capitan (later). Phone is running last sof

  Any ideas how to solve this problem?

  What exactly do you mean by "does not work? What is going on?

• IPhone does not connect to the WIFI in the House when not near router

  This is a recent as problem it used to work fine.

  My iphone connects to the WIFI in my house when I'm in the same room as the router but won't connect to nowhere elsewhere in the House.

  Any other apple device I have works fine, so this would suggest that there is a problem with the phone?

  Is it possible to fix this?

  Thank you

  If your iPhone is in a case, first thing I would try is to remove the case and see if that fixes it.  Other that that, I can't imagine any easy fixes.  This article may help:

  Import photos and videos from your iPhone, iPad or iPod touch - Apple Support

  My next step would be to take it to a nearby Apple store and see if they can diagnose and help you.

• DeskJet 2540 does not connect when the WiFi is enabled

  When online the printer will print not wireless, when the line of the printer print wireless help... aaaaahhhhhh third one is now...

  Hi paulthechef1,

  Using a connection myfi could absolutely cause these issues.  MyFi isn't a supported type of connection, and its functionality with printers is not a guaranteed connection.  I recommend you to connect to a router or a USB cable.

  Please let me know if you have any other questions.  Thanks for posting on the HP Forums.

• M70: WiFi adapter does not connect to the wifi Lan

  Hello
  I have the Satellite M70-122 with an Intel PRO set wireless adapter 2200BG Driver version 9.0.2.25. ConfigFree radar screen correctly identifies the wifi router of my Motorola, but when I click on and get the router on the icon of the laptop, no connection is established and there is a message that says:
  "Sell another application is controlling the wireless card."

  I disabled the "use Windows to configure my wireless" box under settings to connect wireless but no luck.

  In addition, there is no wifi adapter icon in the status bar, or I can get to a window with the settings of the adapter to enter the SSID and WEP details.

  Any help will be appreciated.

  Hello

  Have you used a tool of connectivity like Atheros WLan client utility?
  On WEP:
  PC card encryption is hardware specific. Maybe if it of not possible to use WEP encryption, because the card doesn t that supports.

  Please also see this page:
  http://support.Intel.com/support/wireless/WLAN/pro2200bg/index.htm

  Good bye

• View-PCoIP does not connect on the desktop with ViewPlanner, but does not connect manually

  I saw this mentioned in a few subjects, but I've not seen a resolution.

  I configured a remote view-PCoIP see Planner run profile. The customer and and food Office of VMs on. The Office is a newspaper and connect the client starts the view Client PCoIP. It connects on the view connection server, but not on the desktop. The error message is 'office 'Unknown' is not in the list of desktop titled. (see the folder of the image as an attachment).

  I press the OK button on the error message, start the Client view manually, by using the same credentials see Planner in AD, and I am able to connect to connect to the server, then the virtual desktop computer. The job see Planner runs even at this place (if I don't stop to see Planner first).

  Two days ago, that I was able to run a desktop computer without problem running 10 profile. Since then, I've added several hundred offices at the pool, no other configuration change I can think. The pool is an automatic with floating assignments, office computers are supplied with View Composer. The 'Test' AD security group has the right (see image file).

  I don't understand why see Planner cannot connect to a desktop computer, so that I can do it manually.

  I see the same behavior with a single or multiple, virtual machine run profile.

  Here is an extract from the journal of the unit (all IP addresses are on an area of temporary laboratory, so I really don't like if they are exposed).

  Thanks and greetings

  Wednesday, March 26, 2014 23:17:29 DEBUG add users ['Test_1'] for security AD Group: Test
  Wednesday, March 26, 2014 23:17:29 DEBUG all users added to AD security group: Test
  Wednesday, March 26, 2014 23:17:31 DEBUG returning to the current state: 0 with status message: [IP recorded: desktop: 0, Clients: 0] [the workload began on machines 0] [Uploaded results-> desktop: 0 (0 errors), Clients: 0]
  Wednesday, March 26, 2014 23:18:19 registration of new customer INFORMATION: 10.128.33.73
  Wednesday, March 26, 2014 23:18:19 INFO current registered status machines: [pairs required: 1] [clients: 1] [server: 0]
  Wednesday, March 26, 2014 23:18:20 new INFORMATION server registration: 10.128.33.132
  Wednesday, March 26, 2014 23:18:20 INFO current registered status machines: [pairs required: 1] [clients: 1] [server: 1]
  Wednesday, March 26, 2014 23:18:20 INFO get the IP address Office VM-1 of VC
  Wednesday, March 26, 2014 23:18:21 DEBUG returning to the current state: 0 with status message: [IP recorded: desktop computers: 1, customers: 1] [the workload began on machines 0] [Uploaded results-> desktop: 0 (0 errors), Clients: 0]
  Wednesday, March 26, 2014 23:18:30 INFO get the IP address VM VC client1
  Wednesday, March 26, 2014 23:18:30 INFO got the client1 virtual machine IP address: 10.128.33.73
  Wednesday, March 26, 2014 23:18:30 INFO get the IP address Office VM-1 of VC
  Wednesday, March 26, 2014 23:18:30 INFO obtained IP address for the virtual office-1 computer: 10.128.33.132
  Wednesday, March 26, 2014 23:18:30 DEBUG IP: 10.128.33.73-> name: client1
  Wednesday, March 26, 2014 23:18:30 DEBUG IP: 10.128.33.132-> name: office-1 computer
  Wednesday, March 26, 2014 23:18:30 INFO query: SELECT * from hostinfo where IPADDR = "10.128.33.132."
  Wednesday, March 26, 2014 23:18:30 INFO Running query: UPDATE SET is_Client = '0' hostinfo, State = 'Unpaired', name = 'computer office-1 "where IPADDR = '10.128.33.132'".
  Wednesday, March 26, 2014 23:18:30 INFO query: SELECT * from hostinfo where IPADDR = "10.128.33.73."
  Wednesday, March 26, 2014 23:18:30 INFO Running query: UPDATE SET is_Client = '1' hostinfo, State is 'Unpaired', name = 'client1' where IPADDR = "10.128.33.73."
  Wednesday, March 26, 2014 23:18:30 INFO registration remaining VMs
  Wednesday, March 26, 2014 23:18:30 reached the threshold of the INFO for the number of machines... The plan of starting reference...
  Wednesday, March 26, 2014 23:18:30 INFO waiting for virtual machines to settle and sleep during the time scale
  Wednesday, March 26, 2014 23:18:40 DEBUG of waiting for prefixes map to be extracted from Server view...
  Wednesday, March 26, 2014 23:18:41 INFO function call right with arguments: (pools: [], domain name: domaine.net, groupnames: ['Test'])
  Wednesday, March 26, 2014 23:18:41 groups of security of the object DEBUG AD ['Test'] to the office pool
  Wednesday, March 26, 2014 23:19:10 INFO assigning client-server for 1 pair
  Wednesday, March 26, 2014 23:19:10 INFO Running query: UPDATE hostinfo SET state = 'Matched' where IPADDR = "10.128.33.73."
  Wednesday, March 26, 2014 23:19:10 INFO Running query: UPDATE hostinfo SET state = 'Matched' where IPADDR = "10.128.33.132."
  Wednesday, March 26, 2014 23:19:10 INFO query: INSERT INTO testinfo (test_name, ClientIP_FK, ServerIP_FK, Protocol, username, password, test_state, start_time, type) values ('PCoIP-1VM', '10.128.33.73', '10.128.33.132', 'View-PCoIP', 'Test_1', "passw0rd", "waiting", '2014-03-26 23:19:10 ', 2)
  Wednesday, March 26, 2014 23:19:10 request information: SELECT * from testinfo where testname = 'PCoIP-1VM' and test_state = 'pending' and ClientIP_FK = '10.128.33.73' and ServerIP_FK = '10.128.33.132. '
  Wednesday, March 26, 2014 23:19:10 INFO -.
  Wednesday, March 26, 2014 23:19:10 INFO launch the execution plan for the run profile
  Wednesday, March 26, 2014 23:19:10 INFO -.
  Wednesday, March 26, 2014 23:19:10 DEBUG begins to gather statistics periodically VC...
  Wednesday, March 26, 2014 23:19:11 INFO from the workload for all assigned pairs...
  Wednesday, March 26, 2014 23:19:11 INFO remote command running on 10.128.33.132 machine: Logoff
  Wednesday, March 26, 2014 23:19:11 command run on the remote computer INFO: Logoff
  Wednesday, March 26, 2014 23:19:11 INFO wait until all desktop computers have disconnected
  Wednesday, March 26, 2014 23:19:21 INFO continues the race after waiting
  Wednesday, March 26, 2014 23:19:21 INFO looking for name of the cluster for computer office-1
  Wednesday, March 26, 2014 23:19:21 INFO Running query: UPDATE hostinfo SET state = 'Busy' where IPADDR = "10.128.33.73."
  Wednesday, March 26, 2014 23:19:21 INFO Running query: UPDATE hostinfo SET state = 'Busy' where IPADDR = "10.128.33.132."
  Wednesday, March 26, 2014 23:19:21 request information: UPDATE SET = '1VM-PCoIP' test_name testinfo, Protocol is 'View-PCoIP', name of user = 'Test_1', password = 'Q1w2e3r4!', test_state = 'Running', start_time = "2014-03-26 23:19:11" where test_id = 2837
  Wednesday, March 26, 2014 23:19:21 INFO running commands remotely with args: customer: 10.128.33.73, server: 10.128.216.88, Protocol: view-PCoIP, test_name: PCoIP-1VM, vmuser: Test_1, vmpasswd: Q1w2e3r4!, workprofile: {'IEbpm': 1 L, 'ARbpm': 1 L, "Thinktime": 2 L, "name": "StandardBenchmarkProfile_1i", "hosttime": 1, "random": 1, "iterations": 1 L, 'OMP': 60 L, 'video': 2 L, 'applist': ' WORD, ACROBAT, IE_APACHEDOC, EXCEL_SORT, 7ZIP} {, PPT, FIREFOX, OUTLOOK, IE_WEBALBUM, VIDEO '}, poolname: unknown, domain name: TMIOCONTROL
  Wednesday, March 26, 2014 23:19:21 INFO by adding the callback function for the remote root object to ipaddr: 10.128.33.73
  Wednesday, March 26, 2014 23:19:21 INFO added reminder for the command startWorkload on the client 10.128.33.73
  Wednesday, March 26, 2014 23:21:02 INFO connection started from the client: 10.128.33.73

  I think the name conventions 'computer of office-{n}' and Office-{n}"may be causing the problem. Can you try just to office-{n} and go to View server, open a command prompt and then run "python c:\listener.pyc" and after the release?

• Officejet 5610 - does not connect to the airport with USB

  You want to enable the printer to be used by all devices on my network. Works fine when USB connected directly to my Mac running OS 10.6.8. When USB connected to the AirPort Extreme wireless router, however, printer is visible on Mac and on my network, but is "offline." Cannot get printer to recognize that it is connected. Downloaded the latest version of the driver. Reset all devices. No luck. Any thoughts?

  We will restore the print system:

  -Go to System Preferences > Print & Fax
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• Lenovo-g50-30 does not connect to the wifi at home.

  Hello everyone, I just signed up a solution.

  I got a g50-30 lenovo with windows 8.1 about three weeks ago and I got a wireless problem since then. The laptop connects to my router (Thomson tg582n) but then it shows the limited connection alert. I can browse for about 5 minutes, but just after im unable to do, while the rest of the Smartphones and tablets can connect to it. This problem started about five weeks ago and old macbook, I had, but there does appear to be a fix. In College, I am able to connect to networks without problem wireless and Ethernet works fine as well. I tried everything, reboot and restore the router, change channels and encryption for security, created at the same IP address, I've disabled, restored and turned on windows firewall, released and renewed the IP, DNS blank. Adapter WiFi disabled and enabled, uninstalled the drivers and installed them back again. I did seriously while that I found without success, so I come to you in desperation. It would be the world if you could help. Thank you!

  Thank you VERY MUCH FOR the HELP (note the sarcasm)

  Anyway guys, I found a very good solution which put an end to my connectivity problems. Go to your wiifi configuration and properties and choose to do a custom, DNS server and then type as main Server 8.8.8.8 and 8.8.4.4 as secondary (these are the free Google DNS servers) and all your problems will disappear. If anything, do not hesitate to ask.

• App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra

  App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra

  After upgrade 'OS X El Capitan' to "macOS Sierra" window only empty "App store" and page "Safari" made its appearance, no error message shows. store "iTunes" and "Dictionary" does not connect too.

  But Google chrome works well.

  So have you tried the next steps in your original post that Safari does not work after installing macOS Sierra:

  (1) x OS: "Unable to connect" or "unable to connect to the App Store. An internet connection is required"- Apple Support

  2) Advanced the steps to correct the problems with the iTunes Store - Apple Support connection