HP g60 ssd update

Similar Questions

• Satellite R630-155 - fan is too loud and SSD update

  I am the owner of a Toshiba Satellite R630-155 (Core i5-480). My problems are:

  1. the fan is too loud and never stops. In normal operation (navigation and General Office work) there is a constant high pitch noise which is audible three to four meters in a desktop - high load environment, you just can't take it anymore! The fan never stops... even when you do nothing...

  2. the heat is a big problem. The bottom of the laptop is overheated constantly and I have to place on my desk so that the lower left corner is outside the table, so it can breathe fresh air from below - otherwise, the temperature rises and the (noisy) fan is unable to follow. When I work with the laptop sitting on a couch, I place a thick book between the laptop and my legs. The book must be thick (more than one inch) with hard covers, otherwise the heat going through the book!

  3. last (but not least, I will mention the biggest problems here) that's the problem with the installation of the SSD. I bought a used Corsair F80 (80 GB SSD) from a friend, but I was unable to use it with the Toshiba - BIOS not detect the disc. I tried to install all the latest updates for portable and SSDS but I had no success. Then I put the disc and I bought a brand new Zalman 128 GB SSD (SSD0128N1 Sandforce) but I had exactly the same problem. I contacted my local support Toshiba and after much conversation, the only answer I got is that the laptop is not compatible with these SSDS, and it is acceptable by Toshiba and not their problem. They told me that if I need an SSD upgrade I cannot go for the Toshiba SSD that is installed on the portege series, which is sold by Toshiba for a ridiculously expensive price - about $500 for 128 GB. I contacted the European support center and I got the same exact answer. I searched the Internet and found someone else with exactly the same problem with a Corsair 128 GB SSD - he concluded that the laptop detects the SSD after ten to twenty resets. I tried and it was true - after a lot of restarts the detected disk Zalman laptop and I was able to successfully install Windows 7, but the process is unacceptable. Also the drive is rated by the sites official at the speed of an OCZ Vertex 2 128 GB (and a little better), but when I ran a cue point in the Toshiba, the results I got were less than half of the advertised speed. Same reference in another machine of the same disc, resulted in the announced speeds.

  Shame for Toshiba...-beautiful design and portability, but all the rest is a big flaw. Their support in non-existent and they do not appreciate their customers. According to me, they stole my money and I will never buy a Toshiba laptop again.

  Sorry for the big message, but I need, I warn potential customers. Can anyone help me with any of these problems? You also have the same problems?

  To follow...

  Hey Buddy,

  With regard to the issue of fan and the heat: you did it BIOS update? A friend told Satellite R630 too and he told me that the fan with the new BIOS version 2.10 activity is reduced. In addition, the laptop is colder than before so I recommend to install this update. You can download the update of the BIOS here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  But before you start the update of the BIOS, you should consider the following tips:
  -Run update as an administrator only
  -Unzip all files from zip archive before launching the update file
  -Close all running programs as the antivirus and firewall
  -Make sure the battery is fully charged

  With regard to the SSD it s still a little complicated to install 3rd party products and no one can guarantee that these parts would not work. You're always on the side safely with original spare parts from Toshiba.

  All you can do is to install the new firmware for SSDS and hope that it works, but who knows maybe the BIOS update will help you also in this case ;)

• Panic the kernel constant after the SSD update, what do I do?

  I have a Mid 2012 Macbook Pro 13 inch El Capitan running. I updated to the memory of 4 GB to 8 GB last year and recently updated to a Sandisk 240 GB SSD HARD drive. Now whenever my computer goes into a deep sleep, and I have to wake him up, he resets and says the shutdown because of a problem. The ratio is lower. All advice is appreciated!

  Anonymous UUID: F137A94D-AA92-75D6-26ED-0000FD19BD5C

  Sun 21 Feb 22:15:15 2016

  Panic report *.

  panic (cpu 3 0xffffff80221254ce appellant): "an element of the liberated area has been modified in the kalloc.64 area: expected 0xffffff803f3e5240 but found 0xffffffc23f3e5240, wicks 0 x 4200000000 changed to 0 64 offset in the element 0xffffff803f3e5cc0, cookies 0x3f00116d8f0634e6 0x53521837c75183b"@/Library/Caches/com.apple.xbs/Sources/xnu/xnu-3248.30.4/osfm k/kern/zalloc.c:503.

  Backtrace (CPU 3), frame: return address

  0xffffff802e023aa0: 0xffffff80220df792

  0xffffff802e023b20: 0xffffff80221254ce

  0xffffff802e023b90: 0xffffff8022124c1e

  0xffffff802e023bd0: 0xffffff8022123c02

  0xffffff802e023d00: 0xffffff802263bacb

  0xffffff802e023d20: 0xffffff802263c5aa

  0xffffff802e023d50: 0xffffff80226894a3

  0xffffff802e023d80: 0xffffff802269febe

  0xffffff802e023dd0: 0xffffff802269e72c

  0xffffff802e023df0: 0xffffff802269c2b6

  0xffffff802e023e50: 0xffffff80226a9b42

  0xffffff802e023e90: 0xffffff80226a8d28

  0xffffff802e023ec0: 0xffffff802269ba1d

  0xffffff802e023f00: 0xffffff80226a97e0

  0xffffff802e023f40: 0xffffff80226b4d61

  0xffffff802e023f80: 0xffffff80226b4e56

  0xffffff802e023fb0: 0xffffff80221ccf77

  Corresponding to the current thread BSD process name: kernel_task

  Mac OS version:

  15 D 21

  Kernel version:

  15.3.0 Darwin kernel version: Thu Dec 10 18:40:58 PST 2015; root:XNU-3248.30.4~1/RELEASE_X86_64

  Kernel UUID: DECC9F02-27D7-31F0-9599-A9EF2873902C

  Slide kernel: 0x0000000021e00000

  Text of core base: 0xffffff8022000000

  Text __HIB base: 0xffffff8021f00000

  Name of system model: MacBookPro9, 2 (Mac-6F01561E16C75D06)

  Availability of the system in nanoseconds: 2787425361580

  last load kext to 6836443758: com.apple.driver.AudioAUUC 1.70 (addr 0xffffff7fa4321000 size 32768)

  Finally unloaded kext to 146027300376: com.apple.driver.AirPort.Brcm4331 800.20.24 (addr 0xffffff7fa3f12000 size 2039808)

  kexts responsible:

  com.apple.driver.AudioAUUC 1.70

  com.apple.driver.X86PlatformShim 1.0.0

  com.apple.driver.AGPM 110.20.22

  com Apple.filesystems.autofs 3.0

  com.apple.driver.AppleOSXWatchdog 1

  com.apple.driver.AppleMikeyHIDDriver 124

  com.apple.driver.AppleHDA 272.51.3

  com.apple.driver.AppleUpstreamUserClient 3.6.1

  com.apple.driver.AppleMikeyDriver 272.51.3

  com Apple.Driver.pmtelemetry 1

  com.apple.iokit.IOUserEthernet 1.0.1

  com.apple.iokit.IOBluetoothSerialManager 4.4.3f4

  com.apple.driver.AppleBacklight 170.8.8

  com.apple.driver.AppleThunderboltIP 3.0.8

  com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.3f4

  com.apple.driver.AppleSMCPDRC 1.0.0

  com.apple.Dont_Steal_Mac_OS_X 7.0.0

  com.apple.driver.AppleHV 1

  com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

  com.apple.driver.AppleSMCLMU 208

  com.apple.driver.AppleMCCSControl 1.2.13

  com.apple.driver.AppleLPC 3.1

  com.apple.driver.AppleIntelHD4000Graphics 10.1.2

  com.apple.driver.AppleIntelFramebufferCapri 10.1.2

  com.apple.driver.SMCMotionSensor 3.0.4d1

  com.apple.driver.AppleUSBTCButtons 245,4

  com.apple.driver.AppleUSBTCKeyboard 245,4

  com.apple.driver.AppleIRController 327,5

  com.apple.iokit.SCSITaskUserClient 3.7.7

  com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

  com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

  com.apple.BootCache 38

  2.8.5 com.apple.iokit.IOAHCIBlockStorage

  com.apple.driver.AppleFWOHCI 5.5.2

  com.apple.driver.AppleSDXC 1.7.0

  com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1

  com.apple.iokit.AppleBCM5701Ethernet 10.1.12

  com.apple.driver.AirPort.Brcm4360 1020.17.1a1

  com.apple.driver.AppleAHCIPort 3.1.8

  com.apple.driver.AppleSmartBatteryManager 161.0.0

  com.apple.driver.AppleACPIButtons 4.0

  com.apple.driver.AppleRTC 2.0

  com.apple.driver.AppleHPET 1.8

  com.apple.driver.AppleSMBIOS 2.1

  com.apple.driver.AppleACPIEC 4.0

  com.apple.driver.AppleAPIC 1.7

  com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0

  com Apple.NKE.applicationfirewall 163

  com Apple.Security.Quarantine 3

  com.apple.security.TMSafetyNet 8

  com.apple.driver.AppleIntelCPUPowerManagement 218.0.0

  com Apple.kext.Triggers 1.0

  com.apple.driver.DspFuncLib 272.51.3

  com.apple.kext.OSvKernDSPLib 525

  com.apple.iokit.IOSerialFamily 11

  com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.3f4

  com.apple.iokit.IOBluetoothFamily 4.4.3f4

  com.apple.driver.CoreCaptureResponder 1

  com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

  com.apple.iokit.IOFireWireIP 2.2.6

  com.apple.driver.AppleSMBusController 1.0.14d1

  com.apple.driver.AppleHDAController 272.51.3

  com.apple.iokit.IOHDAFamily 272.51.3

  com.apple.iokit.IOAudioFamily 204.3

  com.apple.vecLib.kext 1.2.0

  com.apple.driver.AppleSMBusPCI 1.0.14d1

  com.apple.driver.AppleBacklightExpert 1.1.0

  com.apple.driver.X86PlatformPlugin 1.0.0

  com.apple.driver.IOPlatformPluginFamily 6.0.0d7

  com.apple.iokit.IOSurface 108.0.1

  com.apple.iokit.IONDRVSupport 2.4.1

  com.apple.iokit.IOAcceleratorFamily2 205,1

  com.apple.AppleGraphicsDeviceControl 3.12.6

  com.apple.iokit.IOGraphicsFamily 2.4.1

  com.apple.driver.AppleSMC 3.1.9

  com.apple.driver.AppleUSBMultitouch 250,5

  com.apple.iokit.IOUSBHIDDriver 900.4.1

  com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1

  com.apple.driver.usb.AppleUSBHub 1.0.1

  com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7

  com.apple.iokit.IOBDStorageFamily 1.8

  com.apple.iokit.IODVDStorageFamily 1.8

  com.apple.iokit.IOCDStorageFamily 1.8

  com.apple.driver.CoreStorage 517.20.1

  com.apple.driver.AppleThunderboltDPInAdapter 4.1.3

  com.apple.driver.AppleThunderboltDPAdapterFamily 4.1.3

  com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2

  com.apple.iokit.IOAHCISerialATAPI 2.6.2

  com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7

  com.apple.driver.AppleThunderboltNHI 4.0.4

  com.apple.iokit.IOThunderboltFamily 5.1.0

  4.5.8 com.apple.iokit.IOFireWireFamily

  com.apple.driver.usb.AppleUSBEHCI 1.0.1

  com.apple.iokit.IOEthernetAVBController 1.0.3b3

  com.apple.iokit.IO80211Family 1110.26

  com.apple.driver.mDNSOffloadUserClient 1.0.1b8

  com.apple.iokit.IONetworkingFamily 3.2

  com Apple.Driver.corecapture 1.0.4

  com.apple.iokit.IOAHCIFamily 2.8.1

  com.apple.driver.usb.AppleUSBXHCIPCI 1.0.1

  com.apple.driver.usb.AppleUSBXHCI 1.0.1

  com.apple.iokit.IOUSBFamily 900.4.1

  com.apple.iokit.IOUSBHostFamily 1.0.1

  com.apple.driver.AppleUSBHostMergeProperties 1.0.1

  com.apple.driver.AppleEFINVRAM 2.0

  com.apple.driver.AppleEFIRuntime 2.0

  com.apple.iokit.IOHIDFamily 2.0.0

  com.apple.iokit.IOSMBusFamily 1.1

  com Apple.Security.sandbox 300.0

  com.apple.kext.AppleMatch 1.0.0d1

  com.apple.driver.AppleKeyStore 2

  com.apple.driver.AppleMobileFileIntegrity 1.0.5

  com.apple.driver.AppleCredentialManager 1.0

  com.apple.driver.DiskImages 417.2

  com.apple.iokit.IOStorageFamily 2.1

  com.apple.iokit.IOReportFamily 31

  com.apple.driver.AppleFDEKeyStore 28.30

  com.apple.driver.AppleACPIPlatform 4.0

  com.apple.iokit.IOPCIFamily 2.9

  com.apple.iokit.IOACPIFamily 1.4

  com.apple.kec.Libm 1

  com Apple.KEC.pthread 1

  com Apple.KEC.corecrypto 1.0

  Model: MacBookPro9 2, MBP91.00D3.B0C of BootROM, 2 processors, Intel Core i5, 2.5 GHz, 8 GB, MSC 2.2f44

  Graphics card: Intel Graphics HD 4000, 4000, Intel HD graphics card integrated

  Memory module: DIMM0/0 BANK, 4 GB DDR3, 1600 MHz, 0x859B, 0x435435313236344246313630422E43313646

  Memory module: DIMM0/1 BANK, 4 GB DDR3, 1600 MHz, 0x859B, 0x435435313236344246313630422E43313646

  Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0xF5), Broadcom BCM43xx 1.0 (7.21.94.136.1a1)

  Bluetooth: Version 4.4.3f4 16616, 3 services, 18 aircraft, 1 incoming serial ports

  Network service: Wi - Fi, AirPort, en1

  Serial ATA Device: SanDisk SDSSDA240G, 240,06 GB

  Serial ATA Device: MATSHITADVD-R UJ - 8à8

  USB device: USB 2.0 Bus

  USB device: Hub

  USB device: FaceTime HD camera (built-in)

  USB device: USB 2.0 Bus

  USB device: Hub

  USB device: Hub

  USB device: Apple keyboard / Trackpad

  USB Device: IR receiver

  USB device: Hub BRCM20702

  USB Device: USB Bluetooth host controller

  USB device: USB 3.0 Bus

  Bus crush: MacBook Pro, Apple Inc., 25.1

  Not sure if it would be a cause of the panic of the kernel, but I have Microsoft OneDrive starts with the computer. Even after disabling this as a point of connection, however, the problem persisted. Maybe I should uninstall all together?

• HP G60-630US: update CPU?

  I tried to upgrade my CPU on my HP G60 630US laptop but it wouldn't start after I installed it. I went back to the original and it started back as usual.
  My question is, the speed of the motherboard bus will support the CPU tried to use?
  
  Original specifications: HP G60 630US laptop
  Motherboard 578232 # 001with Intel Pentium (1 MB of L2 cache) T4400, 2.2 - GHz processor / 800 Mhz
  4 GB of DDR 2-800 Mhz Gskill ram
  HD 500GB Samsung SSD
  
  I tried to install a T9400 processor Intel Core2 Duo (6 MB L2 cache), 2.53 GHz / 1066 Mhz processor
  because it is based on a technical manual, I've read, this is one of the options for this laptop model processor.
  So unless I read the wrong manual, what am I doing wrong? Any help will be greatly appreciated!
  
  I think it has something to do with the motherboard only supports 800 Mhz bus speed... ?
  
  Thank you to who ever can help sheds light on this mystery!

  You are on the right track. When you read the manual, you have to dig a little deeper. In this case, there are two different mothers, one for the GL40 chipset for the GM45 chipset. The GL40 is cheapie, defeatured motherboard without support of the advanced features of the Core 2 Duo as Speedstep processors. Your motherboard is a GL40, given that your processor is the Pentium of lower tier. Some users have reported success with a Core 2 Duo on motherboards GL40 but they run never quite right.

• HP probook 430 g1 with a SSD update

  Hi all.

  I'll be updating my HP Probook 430 G1 with a 512 GB SSD (in fact is 512 HDD with W7 64 professional); Web sites of many factory SSD show the compatibility of their products with my laptop, but Manual HP said that the capacity of the SSD is 128 GB. The cat with the HP support was not helpful. Can someone help me: can I put with 512 gB SDD? I put divers or chipset to AHCI storage level?

  Thank you

  The 128 GB 2.5 inch SSD was just the biggest HP offered to sell the plant. If your laptop has a 2.5-inch SATA drive (some of them operate entirely off small mSATA WSSD readers) then you can replace it with a 2.5 inch SATA SSD of any size on the market. You will not have to pay anything in the BIOS. Your best way to upgrade is to clone the existing for the SSD drive. This should be easy, because they will be very close to the same size. You will need an adapter usb to SATA, but you probably want to get an ayway to continue using the HARD original as external storage drive.

  http://www.Amazon.com/Patuoxun-converter-adapter-cable-drive/DP/B008ASF5MC/ref=sr_1_1?ie=UTF8&QID=1415724695&SR=8-1&keywords=USB+to+SATA

  I use Acronis 2014 Home Edition, but there are several other cloning there, some of them open-source (free). Windows 7 cloning on 2 hard drives of the same size is on the clone easier you will find.

  If you need assistance. Here is the Service Manual:

  Manual

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• W530 Intel SSD update?

  I was curious to know if the current edition of 180 GB Intel 520 a firmwear the updated? Mine seems to be lagging behind increadbily and producing errors on the new operating system windows 8 PRO.

  If Intel recommends not to use their firmware update for the 520 series SSD because it's exclusive for Lenovo OEM, I would hold off. What I can tell you, is that Lenovo does not currently have an update of the firmware for the HARD drive on the driver matrix, so it seems no other updates are available for you at this time. Of course, you can always follow the driver/Firmware updates by reviewing the matrix driver for your machine at any time.

• SSD update for HP Pavilion dv8338ea.

  Hi HP'ers!

  Searched around with no luck. My father upgraded his laptop with an SSD, but I'm not sure if it's a PATA or SATA.

  Although I can't find any information about the specs on the machine, the section of the driver revealed he want to "Intel Matrix Storage Manager", which, according to the text, is «...» Intel Serial ATA (SATA)... »

  Also (assuming that its SATA) it would work with a 250SSD? Or the size will give problems with the bios etc.?

  Thanks guys = D

  The dv8000 series began to have PATA drives, but at one point in the production, they began to install SATA drives. This can actually take 2 hard drives, like the dv9000 series later. The way to know if it's PATA or SATA is to open drive Bay. This is the original SATA (SATA I) but the most recent disks SATA-III will be downclock. There is also a BIOS upgrade that allows him to take Core2 Duo processor and I think also improves some other hardware features and may allow 4 GB of RAM.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-54801-1&cc=us&DLC=en&LC=en&OS=228&product=1832444&sw_lang=

  You must install this update of the BIOS in Windows XP or Vista... it does not work well if you have installed Windows 7.

  Here is the Service Manual:

  Manual

  This manual presents the PATA drives. Look on Page 5-8. PATA drives have two rows of pins in brass, as shown in the manual. SATA drives have two black plastic L shaped plugs.

  There is such a thing as a PATA SSD, but they cost a bit more per concert. HP never sold a lot of the dv8000 the information available here is a little sparse. They are very strong and robust machines however, and I still sometimes run through a service. With the GeForce Go 7600 graphics, it can easily run Windows 7 or 8 with active Aero.

  If you need assistance.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Drive HARD SSD update of HP ENVY 15 - j009wm AMD processor

  I read on some other forums that the Intel chip was required for updates.  I was wondering if it would be possible to upgrade the HDD of 750 GB in this laptop to an SSD.

  Hello

  Yes. No difference between Intel & AMD processor. You can replace the HARD drive existing DSS to get better performance.

  Kind regards.

• HP Pavilion G6 2310se: HARD SSD update drive

  Hello
  I'm running the disk HARD 500 GB 5400 RPM for the moment and it is slow for me. I want to update for Samsung (MLC) 128 GB sata III 6.0gbps 7 mm (Ultraslim). with a caddy HARD drive where I can place my HARD disk to store data and SSD is used only for windows boot. I can not find on the internet if my laptop supports SATA III or not? and it will boost speed up my laptop or not?
  any help please.
  
  Other features are 8 GB DDR3 RAM, Intel 3210 M core i5 processor and other things like bluetooth wifi etc etc.

  Hello
  
  Manual: http://h10032.www1.hp.com/ctg/Manual/c03593041
  
  Data sheet: http://support.hp.com/us-en/product/HP-Pavilion-g6-Notebook-PC-series/5330578/model/5361234/document/c03693385/
  
  SSD upgrade will improve the time of startup and overall performance drastically than anything else. SSD boot drive is an excellent choice. Use tools of cloning the SSD manufacturer (from their website) or other free tools available, to migrate the OS.
  
  Download, run this tool to know the SATA HDD type:
  https://www.Piriform.com/Speccy
  
  SSD now on the market is of SATA3 (6Gbps), it'll work in your laptop your model SATA connector to be I, II or III. They are compatible with reverse.
  
  Concerning
  
  Visruth

• HP ENVY 17-j020us Quad Edition Notebook PC RAM and SSD update

  Hello I was wondering if it was possible to update the card I have now

  Currently it has 8 GB of DDR3 memory, 1024 GB 5400 RPM hard drive. I also wanted to know if I could downgrade to 8.1 for windows windows 7

  Thanking you in advance

  Hello

  Manual: http://h10032.www1.hp.com/ctg/Manual/c03922401.pdf

  Data sheet: http://support.hp.com/us-en/document/c03754267

  Driver download page: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5408157

  RAM: You can spend in total 16 GB MAX, put two 8 GB DDR3L PC3L-12800 1600 MHz SO-DIMM SDRAM into the two slots. I wouldn't do this if I'm going to upgrade SSD and it's more than enough unless you're going for heavy fabrics intensive programming & resource.

  SSD: Yes, you can replace SSD HARD drive in the main Bay and make the boot drive SSD SSD HARD drive cloning. If your model has two hard drive Bay, you can move the HARD disk to secondary Bay - to buy the kit of additional hard drive for this property in the Bay.

  Decommissioning: You may need to clean install Win 7 after buying the product key of Microsoft. Downgrade rights are given now for version 8.1 of Win Pro for laptop OEM. Drivers for Windows 7 are available in the download of your model site.

  Your laptop came with Windows 8,

  http://m.WikiHow.com/downgrade-Windows-8-to-Windows-7

  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/downgrade_rights.aspx#fBid=fV92IN3PQMD

  Concerning

  Visruth

• HP Pavilion 15 not: SSD update for HP Pavilion 15 laptop

  Hello!

  I use PC HP Pavilion 15 Notebok (F6C42PA #ACJ). It came with Win 8.1 pre-installed on a 1 TB HARD drive. I updated the OS to win 10 and now upgrade my HDD to SSD. I was wondering if TS256GSSD370S Transcend and Samsung Evo 850 is compatible with my laptop. Also how to enable AHCI mode? I don't see such an option in the BIOS.

  Thank you.

  15 - n203tx is the model. Here is the Service Manual:

  Manual

  The compartment access hard drive appears on p. 59. As you can see, it's a bit more involved.

  Don't fall into the trap of overthink. The laptop is in ahci mode and you can not set otherwise. With Windows 10 an SSD will be automatically recognized as such and optimized. Your question only real tech is to get the software on the new SSD. After the back if you need some help with that.

  The Samsung Evo 850 is my choice, but the Transcend would work too.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Pavilion a6536de: SSD update of my pavilion a6536de

  Hi, I upgraded my desktop pavilion a6536de (ASUS M2N68 - Rev.3.02 Council, name of HP: Narra3-GLBE) with an SSD. But the Board of Directors/Bios do not support AHCI Mode. Is there a BIOS or update driver, as I'm enjoying my new SSD? I can't find a BIOS update or update need driver on your driver support page. Thank you for the help

  HP has their motherboards manufactured to their specifications.  So, no updates to the BIOS of detail from other manufacturers will not work.

  Their policy is to provide BIOS updates when there are a lot of problems with some model.  However, to develop a BIOS update for all the new components that are introduced every day would be a nightmare.  It is a process very involved to update a BIOS or any driver.

• the iMac 2010 SSD update

  I'm new to this forum. I'm going to be when you run an upgrade for my iMac next week. I have an iMac mid-2010 with processor i3 3.2 GHz and 8 GB of RAM (model MC509LL/A). My question is: would this work of SanDisk Extreme SSD 120 GB with my iMac? Also, I'll do any upgrade of the previous stage as firmware update... etc? Any help is welcome.

  Some iMAC models have disks 3.5 "bays. If you have one of these models, you would need some brakets editing being 2.5 SSDS ".

  http://www.EveryMac.com/systems/Apple/iMac/iMac-aluminum-FAQ/iMac-Intel-21.5-inch-27-inch-aluminum-h...

  All iMac models ' end of 2009 "- the iMac"Core 2 Duo"3.06 21.5", 'Core 2 Duo' 3.06 27 ", and "Core i5"2.66 27" - and all models of "mid-2010"-the iMac "Core i3" 3.06 21.5 ", "Core i3"3.2 21.5", "Core i3" 3.2 27 " and "Core i5"2.8 27" -have a 3 Gb/s SATA 2.0 for a disk connector 3.5 "hard." "Mid-2010" of 27-inch models - the iMac "Core i3" 3.2 27 " and "Core i5"2.8 27" -also have an extra 3 Gbps SATA 2.0 connector and the power for the option 2.5 "SSD (in addition to 3 Gb/s connectors Serial ATA 2.0 hard drive and optical drive).

• Envy 17 3D to SSD update

  I have an Envy 17 3D, and I wanted to upgrade to an SSD Boot drive to speed up things and eek out a little more autonomy. I got a 3 OCZ Agility 120 GB SSD, I was able to run through the recovery DVDs, I created to install Windows 7, but on reboot I now get a "PXE - E61 media test failure" and it does not start. When it is installed as the 2nd player, I see the player very well, including the Windows files.

  I've updated to the latest Firmware, 2.15, same problem. Any ideas what could be causing the problem?

  For memory, the start of the recovery of the DVD I had created to enter recovery mode, I was able to run the Boot recovery tools (BootSect.exe) to resolve the startup problem, I am now running on my SSD.

  Unfortunately, I didn't connect with care what finally fixed command flag, but I don't know that it took more than just fix the MBR.

• HP G60-510WM, updated CPU GL40

  I have a G60-510WM (screens of cpu - z attached). I bought a P8600 on eBay, he came with bent pins that I straightened but black screen on startup. Not sure if it is because it is not compatible and the chipset can handle that front side bus at 800 mhz, or because the processor has been broken. If someone could shed some light on cpu compatibility that would be incredible. (As in what processors/fsb I can actually run before I have buy another without knowing)

  Thank you

  -tabormeiste

  

  

  Hello:

  I think that the processor is bad.

  I have attached the link for the service manual for your laptop. Supported processors are listed in pages 1 and 2.

  http://h10032.www1.HP.com/CTG/manual/c02985882.PDF

  The P8600 is listed as supported. I have a HP 6930p notebook with the ICH9M and there a P8700 inside.

  Check the support page for your laptop and make sure that there is no necessary BIOS update which adds support of these processors.

  Is there and you need to Flash the BIOS, make sure absolutely that Flash by using one of the operating systems supported flash was designed.

  Paul