HP LaserJet Pro 400 M401dne print only one page (document)

Similar Questions

• HP Color LaserJet CM1312 nfi no print only one page (document)

  Hi all.

  I'm in big trouble with Color LaserJet 1312 nfi (on 2 PC). Printer still print ONLY a single document (regardless of the number of pages) that I can't continue. I have to restart computer or the user to login and I print a new document. Scan OK.

  PC config:

  Windows 7 x 86

  connect via the USB port (but LAN made the same mistake)

  PCL6 driver

  I tried:

  reset to factory default

  the latest firmware update

  connect via LAN instead of USB

  Print via another PC (printer sharing)

  connect the printer to the other PC (USB, LAN)

  install the drivers of PCL5

  turn off Mopier mode (not available)

  Win XP - OK (printer so no problem)

  Any ideas?

  Thank you.

  Hello.

  Installation new version Universal Print Driver for Post Script - no change.

  I tried a thousand ways and WE work:

  install driver of the old school-HP Laser Jet III from Windows Update.

  I hope it helps someone...

• HP LaserJet Pro 400 m401dne: print from Notepad

  Hello! I have a new HP LaserJet Pro 400 m401dne. Everything works fine except when I try to print both sides of a Notepad document copies. As soon as I select the duplex option, the entire document disappears. We had an another HP LaserJet only printed on one side of the paper; who would have something to do with it? Still, I have this printer on the printer list but am selecting a new. I can print any other documents on 2 sides; just don't leave the notebook. Thanks for any help you can give me!

  Thank you, HP! The warranty issue has been resolved and so was the two-sided printing problem. The technician had to install Universal printing and now I can print copies front and back of notebook and everywhere else.  )

• Drivers for HP LaserJet Pro 400 M401dne printer

  Hello

  Product page: http://store.hp.com/UKStore/Merch/Product.aspx?id=CF399A&opt=B19&sel=BPRN

  I bought this printer, so it can be shared among a group of approximately 5 members of staff. I usually download and store drivers for printers etc. on the network and install from there but am unable to find any sort of link from where I can download the drivers 32/64 bits for this product.

  I need to specific drivers, not the UPD. The UPD is very good for the generic print jobs, but does not work with certain software.

  Whenever I try to find a driver for this device links form a circle and just send you back with the same pages.

  I am from this page:

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome?sp4ts.Oid=5307051&AC.adm...

  Can someone provide a link to the 32 and 64 bit Windows drivers for this product, please?

  Thank you!

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Best wishes!

• set the printer to print only one page always

  I have a HPlaserjet MFP 1005. I want to put to print only one page which isusually necessary. How do I?

  Hey @neelp,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I see you try to set your Laserjet P1005 MFP always print one page only. This isn't an option through Windows PC or Apple, but there are two ways to work around this problem. The first would be to pay attention to what is being printed by activating the mode print preview before you print. The second solution would be to have only a sheet of paper in the printer at any time.

  If you have questions about the verification of print previews please let me know which operating system you use on your computer but also what program you use and I see if I can help you with that. If you are not sure what your operating system is you can click here to find. Even if you have any other questions please let me know.

  If this solves your problem then please let other users of the forum know clicking on accept as a Solution.

  I hope this helps and I hope you have a great weekend!

• laserJet Pro 400 color: printer

  Hello Mr President
  I want a help on your part I have a Color LaserJet Pro 400 m475dw MFP
  and when I turned it on. I show masseage like this {10.1002 electric memory error}
  How can I solve this problem, Mr President

  Hello Sir,

  The error that you expose is a problem with one of the toners.
  The magenta to be precise.
  
  In this case, the recommended action is to replace the magenta toner with an original RESUME.
  
  Kind regards

• Help! My M475dn MFP HP LaserJet Pro 400 color printer will NOT print!

  HP LaserJet Pro 400 color MFP-M475dn-CE863A

  Printer on a network and can connect to multiple computers that include: Mac OS X, Windows 7 and Windows XP.

  When I try to print from my iMac, the print queue of the printer says "the printer is not connected.  When we try to print from Windows computers, it is in the right queue and does not print.  When I go the printer itself and try to print a page of demonstration or page supplies directly to him, it says on the screen which is printed, but nothing happens.  This is not hum or anything!  The port where the network cable is connected is switched on green that says HP which means that the network cable is connected.  We've had this printer for a year now, and something like that never happened.

  I did not have any software or anything like that until this happened.  It was working fine on Saturday when we used it, but when we arrived at work today, he just decided that it would interrupt printing!

  I'm puzzled!  I tried 'ping' IP address of the printer from my iMac and it pings fine.  Does anyone have advice?

  (I tried to make of the obvious like too switch the printer on and off and shutting the computer down and nothing!)

  Okay, so I feel a bit stupid right now.  I decided that I would be closed the printer for about an hour to see if it was there, and what you know-it has been!  I had to turn it off several times before but I guess it wasn't long enough.  What a pain!

  Thanks to everyone who took the time to read this!  Sorry to waste time everyone!

• LaserJet pro 400 m451nw - Print is too dark

  I have a LaserJet Pro 400 M451nw color, and every time I print any type of blue, it prints really dark.  Tonight, the blue on my monitor was a royal blue, and blue printed was almost black. I reduced the blue on the graph, but it's still not royal blue.  The program I use is MS Publisher 2013.

  Is it possible for me to adjust the parameters of the cyan cartridge, so it will not print so dark?

  Thank you

  SHJ

  Hello ayligcjdesign,

  Welcome to the HP Forums.

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Thank you for your time.

• HP Officejet Pro K8600: Power light + resume light flashing after printing only one Page

  After trying to print a document of several page, the printer produced a page and then the power light and the resume light (page feed) Flash. I also tried to print multiple copies of a page, but that leads to the same result.

  I can get the lights extinguish by turning printer off then turn it back on. But it will always print that one front page the same lights begin to Flash. I did six times in a row just to print a six page document.

  I went through all the steps in troubleshooting HP software. Not like searching for cleaning print heads, re-seats cartridges, etc., fragments of paper. Nothing seems to work.

  @Bob_Headrick

  Thank you for your response. However, none of the suggestions could solve the problem. ALTHOUGH the light guide troubleshooting that you provided was close to the solution.

  I came across the solution by reading the PDF manual for the printer. On page 77, it describes the power led + resume light flashing. One of the causes for this using EXPIRES of CARTRIDGES of INK, CARTRIDGES RECHARGEES or NON HP CARTRIDGES.

  WARNING: It is important to note that if your printer is still under warranty, DO NOT DO THIS. HP notes in the manual using this substitution can void the warranty against damage caused by the use of faulty ink cartridges, obsolete or not allowed.

  SOLUTION:

  While the power light and button resume flashing, press and hold the power button and press the button repeat 3 times. This replaces the "apparent" internal error message to use the cartridges you have installed. It may also cause a print cartridge alignment page.

  MY OPINION:

  It is important to note the HP cautioned against it, it FIXED MY PROBLEM IMMEDIATELY! I know that the cartridges that I have installed are in agreement. Like many HP owners out there, I take advantage of sales and have stored on cartridges. I guess some may "expires" before you install it. In my view, the idea of "expiring" cartridges also somewhat falls into this column to "How can do us buy more ink?" What kind of market we create where it's cheaper to buy a new printer than to buy a new set of cartridges/toners? BUT it's a slippery slope... let's not go there.

• Photosmart 7510 prints only one page when I copy 2 sided-multipage document

  I have a two-sided 4-page document. I have placer place in autonatic tray, select Copy 2 head to head 2 and press "Black." All pages are scanned, but only one page (2 sides), one out. I expect all 4 pages 2 faces out. What's wrong?

  Thank you.

  You are right. This printer does not the ADF duplex scan. It will print a copy of the 2 sides but the face page of the first page front and back on the face of the first page printed copy pages and page of the face of the second duplex page on the back of the first page printed from copy. What a waste. Well, I need now to decide if I want to keep this printer or send it back since it's the LPB brand.

• HP LaserJet Pro 400 M401dn: Printer setup error

  I use this printer for these past two years perfectly, but last week when I changed my laptop start to become more error during installation. My laptop machine specs are also less

  

  Error message

  

  I tried several ways by downloading the latest version of the driver from the HP Web (http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5096261)

  I also try to install optional Smart Install

  Please help me

  Wakeel

  To make this real simple.  Go to the printer and to the control panel of the printer print a config page or network config which will give you the ip address of the printer.  Now on your computer, go to devices and printers and choose the item add printer, then local printer and on the next page, click on the create a new port and in the drop-down menu, choose standard tcp/ip and then click Next.  Type the ip address of the printer and make sure the box to query the printer and automatically select driveris checked and then click Next.  The computer will find the printer and load the required drivers and set up the printer for you.  If this does not work, report back with what happened during the installation (error messages, etc.).

• LaserJet Pro P1102W: P1102W displays only first page or two of a job

  A week or two ago, my P1102W stopped the complete print job. It would seem that the first page, sometimes two. Would the Green LED flashes quickly rather than the pulse slow (3 seconds) when a work is done. By pressing on the red X button often causes another page to appear but it only works one or two times, after which the rest of the work was lost.

  Hi @Tuttle,

  Welcome to the HP Forums!

  I see that your HP Laserjet Pro P1102w only prints the first page or two of work on Windows 7. I'm happy to help you!

  If please, try the procedure described in this guide, Print Jobs stuck in the queue (Windows)and let me know what happens! (Even if the title of the guide may not correspond to your question, I think that the solutions will help.)

  I hope this works!

  "Please click the Thumbs up icon below to thank me for having responded."

• LaserJet Pro 400 M401dne problem Duplex - duplex printing on its own from Windows computers.

  401dne's all jobs from two sided printing windows different computers even if I did not turn on "Print we Both Sides" in the properties of the printer from any application. I even check it whenever I print. A MacBook Pro with OSX 10.8 also have printing on this printer and is not Duplex no print jobs. Note This duplexing on its own comes in all applications (printing from IE, Office 2013 etc.).

  I upgraded to the latest firmware and update the latest drivers to print (complete solution install). A printer connected via network domestic (hard wired ethernet to the router) being accessible by two computers Windows and a Mac.

  How can I fix this to the o of Windows computers, I can print on the front of each page only, when I want to.

  Thank you

  Problem solved. I contacted HP Support by Chat online and we opted for the PS driver. It works correctly, a face print individual pages, Duplex prints two pages on one. So yes, the PCL6 driver is deficient.

• Color LaserJet Pro 400 M451dn: Print vs wireless network

  I used my printer Wireless Ethernet connection between printer and Apple airport base station. I am moving and can use printer wireless without direct connection to the router? (Printer & new router in place will be not near each other for the direct cable connection is not convenient). Thank you!

  Hello @Cary2

  No way, it's a D M451dn stands for double-sided N to the network (wired network), only the M451dw will have the possibility of having the wireless

  The printer must have a wired network to the internet permanently connection

• HP LaserJet Pro 400 M401dn: Printer PCL XL Error

  Hi all
  
  I am help out at school and class times year book are coming and the aret students print their drafts. but when printing from Adobe indesign CS5 is the error we get:
  
  Error X PCL

  Subsystem: TEXT

  Error: InternalError 0 x 50

  File name: Cheettext. c

  Line number: 710

  I am brand new to all this, so any advice would be great! Thank you!

  Hello

  You can try putting the printer off, unplug the cord of her power and wait 30 seconds.  Plugged in, it works.

  Hope it will solve your problem.

  Good impression