HP Officejet Pro 8600. Have multiple pages need to scan!

Similar Questions

• Lack the HP (Officejet Pro 8600 Plus) utility. no need to reinstall - cannot uninstall the printer software

  I had to wipe my iMac and resinstall IOS Mavericks (10.9.5).  Printer (Officejet Pro 8600, 9N11g) works, but won't scan (double-clicking icon in "original item cannot be found") and the HP utility on dock icon is absent, replaced by a "?."  I found instructions to uninstall the printer software so I can reinstall... but there is no longer any HP or "Uninstalling HP's" on my Mac HD folder.  Not there at - it a HP folder in the library/printers folders.  Research Spotlight shows no HP or Hewlett-Packard folder on my hard drive.

  I downloaded a 'HPPPrinterDrivers3.0.dmg' and ' HP-Injket-SW-OSX - Mavericks_v12.34.37.dmg, "which I'm hoping will contain updated software/drivers to reinstall the printer and I hope as the HP utility so I can resume the scan function, but I can't understand how to remove the current printing software, and I don't know if those are the files migrate to use.  I understand just remove the printer will not be enough.

  Can someone provide step by step instructions how uninstall the software and installation (since I don't know if I have the correct dmg files)?  Thank you.

  Hello

  First I offers to repair disk permissions, and then try to reinstall the HP software.

  Follow the steps below to repair disk permissions:

  1. open the Applications folder.
  2. go to the Utilities folder.
  3. double-click on disk utility.
  4 Select the hard disk that contains the boot volume.
  5. go to the first aid tab and select Repair disk permissions.
  Note: This process may take several minutes depending on the Mac and the amount of the permissions that need to be repaired. The progress log shows when the process was completed.

  Once you are finished, run the HP-Injket-SW-OSX - Mavericks_v12.34.37.dmg and follow the instructions on the screen, be sure to select the option of Scanning HP when installing to get all the features of the software.

  Please, try the above steps and let me know the results,
  Shlomi

• OfficeJet Pro 8600 more full page

  How can I get the HP Officejet Pro 8600 more printing bleed? In portrait mode, it leaves a. 1 "margin on the right side and bottom. I went into the menu advanced and selected without border and use of photo paper.

  Thoughts?

  Hello

  Which application do you print? What is a photo/image or text? Please check the following information (from manual page is #43):

  

  Kind regards.

• OfficeJet Pro 8600: Officejet Pro 8600 leaves black lines on docs scanned when using the document feeder

  This is the second HP Officejet Pro 8600 I had - one was replaced by HP, after that the same issue arose.  I tried to clean the entire unit, but we still get a thin black line running vertically down the page.  This line is divided into sections of 1 "and 2.5" in length.  Sometimes I get the fine line and then almost a shadow line that is parallel.

  Any suggestions would be very appreciated I have scan documents to PDF format and it's hassle to put everyone on the flat for scanning.  I use the charger of the doc on a daily basis and wonder if this could have something to do with the lines.

  Thanks for any help.

  The question is a spec on thin (~ 1 "wide) glass to the left of the main bed scanner.  Clean this area as described in this document.  It can be difficult to see the affected area, a bright flashlight which is held at an angle to the glass can help find the place.  Even a very small spec on the glass can cause a black line when using the ADF.

  

• OfficeJet Pro 8600 Premiun: deleting e-mail in scanning to e-mail option

  My scan-to-email address book is full. I need to remove the address that I no longer use. I have not found the option to do so. Any help would be greatly appreciated. Thank you

  Hello @ImaTazzie73 ,

  I understand that you have difficulties to change the address book for your Officejet Pro 8600 Premium.

  I want to help you with this.

  He says that your operating system is windows 7. On your desktop, you should have an icon that looks like your printer.

  It should be named HP Officejet pro 8600.

  If you double-click on this it should open the Printer Wizard.

  Here there is another icon, you can click to scan to e-mail.

  It should open a tool that will allow you to edit the address book.

  Another option is as follows.

  Tap the wireless on your printer and note the IP address.

  Using Chrome or another favorite browser, type the IP address in the URL bar.

  This should take you printers EWS (built-in web server)

  Select the tab labeled scan.

  You should now see where you can edit or change your address book.

  I hope this helps you. Let me know if you would like more details, and I dwell.

• HP Officejet Pro 8600 - black lines when copying, colored scanning lines

  Hello

  I have a HP Officejet Pro 8600. When I try to copy from glass, copy of ADF, I get black lines going the length of the pages. Whenver I scan, once more, the glass or ADF I get lines colored, ranging from the length of the analysis. I called HP customer service and the representative told me clean the glass and part inside of the ADF, but the problem still remains. No idea if this is a common problem? More important still, how fix it.

  Do a hard rest on the printer. Let the printer and unplug the power cord. In doing so, it will remove the lines.

  When a solution is found, please indicate the position that solves your problem.

  If I have solved your problem, please do not hesitate to provide laurels and make sure that you mark this thread as provided solution!
  Although I work for HP, my messages and responses are my own opinion and not of HP

  Valerie, printer Agent

• OfficeJet Pro 8600 more. No menu auto scan when loading documents in the ADF?

  I have an Officejet Pro 8600 more again to replace the L7780 who brought up the menu scan, when a document is loaded into the autofeeder.  How can I get the only 8600 to do the same.  I find that I liked the convenience of the automatic menu, but it does not come to the top when I load the document (s) to scan in the ADF.  This feature has been discontinued?

  Thank you.  I do enjoy the printer but miss this feature that I scan all my documents in my computer to avoid to keep a lot of paper.

• OfficeJet pro 8600: not possible to change the scanning of the Panel of the printer resolution settings

  With my Officejet pro 8600, there is no possibility to change the scanning resolution settings when you are working in the control panel of the printer (not present button to touch) when I want to scan to the computer, while in the manual it is mentioned that, after pressing the Document Type, it should be possible to reach the resolution to change the resolution of the scan setting. On the other hand, when the scan to a memory card the button change the resolution settings is present.

  Sometimes for the scanning of all computers to select (winXP SP3 installed on it). The HP printing software is installed on all computers and manage digitization to the computer is turned on. It is possible to change the resolution settings when using my computer with the HP printing software, but as I said not in the use of the printer.

  Thank you to help you solve the problem!

  Hey mk75053,

  Scanning to memory card has the parameters of resolution through the front because that is the only way for the device perform this type of analysis.  However, to change the resolution settings for the Scan of the computer, one will have to perform scans through the software installed on the PC.

  I have all three types of 8600 models where I am located (base, more high quality) and of all printers simply ask to start the analysis after selecting the scan type.

  I hope this helps.

• OfficeJet Pro 8000 prints multiple pages of the same document

  Info:

  HP Officejet Pro 8000 A809a

  Windows 7 Pro 64-bit

  Last driver and firmware from HP

  When a job is sent to the printer (web, Word, Acrobat, etc.) the printer keeps printing multiple pages of the document.  Sometimes it will print the first page and a second partial page, then it reprinted again and stop at the same place on the partial page.  She does over and over again.  I ran the HP Diagnostic Utility and it was impossible to print a test page, even after turning the power on power off, then on.   Any suggestions, or is * another * bad printer?  The first was sent and replaced, so I think that this model is just a lemon.

  Thanks for the suggestion, but it didn't work.  I tried to reinstall the driver altogether package three times with no result.  I ran the utility programs that supposedly allows you to solve problems, but public services could not even to generate a test page.

  It seems that I finally found a solution, however.  I installed an older driver for MS Vista 64-bit, and that seemed to do the trick.

• OfficeJet pro l7580 load multiple pages

  I have trouible occasionally with my loading several pages OfficeJet l7580.  I did a search and found the subject, but the image and the description of how to clean the rollers and the separator button did not correspond to what looks like my L7580.  Or maybe that I don't see how to get open.

  The url with the image of the printer is:

  http://support.HP.com/us-en/document/c01110474

  I took a picture of what my L7580 looks like with the door open, but I don't have a url I can to load.

  Thank you for your help,

  {deleted personal information}

  You should be able to lift the upper part of the ADF and open this area with the firm applied pressure. Once opened, these areas must be cleaned with a fluffy like a coffee filter.

  The ADF door may not want to move, but should be open if you pull it gently.

  -Spencer

• HP Officejet Pro 8600: print the page top

  When I print the forms on the internet - in this case a specific Web site - printing cost overruns the right margin of the page, so I see all of the form that is being printed.  Last year when I printed this form, it fits on the page very well.  Same computer, same printer

  This happens on a number of sites that I deal with, so I don't think that there is a problem with the site, I think it's a problem with the installation of the printer, but I have no idea what could be the cause of the problem.  Any help would be appreciated.

  Hey @Monajo,

  Thanks for getting back to me regarding this printing problem.

  Now that we have isolated the problem to a problem of Mozilla Firefox, we can work toward a resolution. To begin troubleshooting I have you check the page scaling settings within Firefox. Please follow the steps below.

  1. open a Web site that you want to print from Mozilla Firefox

  2. click on the Firefox Menu option and select print

  

  3. you will now see a print preview of what will Mozilla Firefox 'send' for your printer to print. Click Page layout on the top

  

  4. in the Page layout dialog box, you can select the 'reduced to fit page width"or"scale"option If this is not the case try first "Reduced to fit Page Width" option. If it is already selected, choose the scale option. You can play with the scale. For example, I adjusted my scale to 20%. When I hit OK, the print preview window shows the document to print as tiny. That's what your printer will print. If it is too small, you can click the Page Setup button again and adjust the scale until you find a scale that displays the preview before print correctly.

  

  5. press print once you make all necessary settings.

  Don't forget, your printer will print than it is "said" to print through the preview window before printing.

  Please let me know if the setting of the "Shrink to the width of the Page" or "Scale" options fix this problem for you. Good luck!

• HP Officejet Pro 8600 Premium: White Pages

  When I print an invoice, it will display and about 10 seconds later, a clean sheet will spring. Only when you make bills not just anything.

  It seems that the Sage is an accountant or an office program. These programs tend to cling to queues of printing or keep their own internal printing queues. The only thing I can suggest is removing and adding the printer in Sage. If you still can not print correctly then the next step would be to communicate directly with the developers for Sage.

• OfficeJet Pro 8600 Plus N911G: Cannot use the Scan to PC, option on my printer

  I recently updated from Windows 8.1 for Windows 10 and had to reinstall my printer drivers and software.  Since doing so, the office of my printer scanning function did not work.

  When I use the option on the printer, I get the message that no computer I'm done to open the HP printing software, select the scanner actions and select manage the scan of the computer.  The only thing is that twhen, I go to the HP folder in my Start menu, there is no installed printer HP software.

  I went to the page support and download the complete software solution for my printer and ran the installation, but I still do not have anything that will allow me to select the actions of scanner, and then select manage the scan of the computer.

  I even tried to use HP Print and scan v4.7 doctor.  He said full software solution is not installed on my computer and it gives me a button to click to download the software, and it is said that it downloads all the 123 file meg, then it gives me an error download failed message and offers try again immediately, but it fails every time.

  My printer is connected to my PC via my WIFI router.

  Hey there,
  Try the next step, I believe that this will help you overcome the problem.
  1. remove the printer driver of "devices and printer" which is located in Control Panel.
  2 Download this file (http://ftp.hp.com/pub/softlib/software12/COL40120/bi-108858-4/OJ8600_1315-1.exe), which is the solution full HP JO 8600 series.
  3. extract the contents of the file.
  4. open the "Utils" folder and choose the folder 'x 64', inside you should be able to locate a file called "RemovePreInstalledDrivers" > once you open this file black screen opens, wait for it to close, then move to the next step.
  5. go to the main folder where you have already extracted the software and right click on the file x 64.msi (name is most likely your printer model), then choose the Option "repair". > Subsequently, you will be asked of preformed a reboot. (Incase you will get a Messege saying "this action is only valid for products that are currently installed" simply double-click the file instead)
  6. after the restart, the head disk Local C/ProgramFiles/HP/PrinterModelFolder/bin/USBSetupLuncher and double click it.
  7 start the installation, choose the wireless option.

  Who should add the scanner to your imaging devices.
  Best Of luck ~

• OfficeJet Pro 8600: Backup does not work after scanning.

  Once I scan a document, any backup option is selected (JPEG, PDF, TXT, etc.), check the button remains greyed out, leaving the only option to cancel and exit without saving changes. It was working fine until I upgraded OSX 10.11 to macOS 10.12

  Hello @RSofNJ, greetings!

  Thank you for visiting the Forums from the HP Support! It's a good place to find the help you need, other users, HP experts and other support staff.

  I see you are using a MAC Sierra and encounters a problem during analysis.

  I recommend you to try to use easy to analyze in the MAC Sierra HP scanning app. Go to http://hp.care/2dVzZC9 for instructions on how to download and use the easy scanning HP application.

  Please let me know if it works for you. Nice day!

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• OfficeJet Pro 8600 N911g: MAC 10.11.2 SCAN TO COMPUTER don't WORK DO NOT OFFICEJET 8600

  I have upgraded to Mac 10.11.2 yesterday evening.  Now, I get this error.  Tried to reinstall the software and restarted the router and the computer to the printer, tried with wifi and LAN.  I guess it has to do with the update.  I can scan the Mac, but NOT the printer to the Mac.

  

  The USB cable is a successful work around.  LAN and WIFI gve the question