HP Pavilion HPE h8-1090 t: Sidebar replacement

Similar Questions

• HP Pavilion HPE 1090 t: could someone help me please... Desktop HP Pavilion HPE h8-1090 t CTO - PSU replacement/compatibiliy

  I just bought a new power supply (Corsair CS650M) because someone has suggested that it would be a good replacement power supply for my HP model which is HP Pavilion HPE 1090 t.   I need to know if this Corsair works and is compatible with my system, because something is not working with him directly or I did something wrong.    This is my first install and when it comes to the ins and outs of power amplification entry & exit and amperages I get so confused about this stuff.   But I think I took all the pluged connection correctly, at least when I re-plugin my old PSU after the installation to fail, I had the PC working again, what made me give confidence that I did the Corsair install correctly.  But what happens is after the installation of the unit from Corsair and turn the system he clicked power off after about 10 seconds or more and then restarted after a few seconds, then stopped again and turns off after another 10 to 15 seconds, and nothing would come up on top of the screen no more.   The first time I did the research what PSU would be compatible, I was getting conflicting results with a few places on the net saying that the majority of the HP out there (excluding some models such as the slimline) could be replaced by different manufacturers and higher power PSU, while other places I looked different.   Even the person who recommended me this power supply said in his post that he installed a Corsair HX650 model in its HP PC, and it worked very well for him.  Now, after the failure of the installation for the next few days, I did a lot more research and when I went on the site of HP and looked up the specifications of the model my PC I noticed under the power supply section, he had a heading that says "must select one of the following options" (in fact most of the different sections shows that the title too) and then he showed only two options 460W and 600W.  Then he asked me if it's the only option I get with my model.  And then I looked at my model number HP on the HP PartSurfer and under the section of the PSU, it also registers only 460W and 600W.   So who is?   I have to stay with only these options two HP or can I get a power supply with a higher power a bit then 600W from a different manufacturer that is what I want.    If I can get something that is compatible other than the options listed HP please let me know, or if this Corsair should work someone please let me know.   I need to return it otherwise.    My specs are below.

  Thank you Aaron

  HP Pavilion HPE series
  Model No.: h8-1090 t CTO Desktop PC

  Name motherboard manufacturer: IPMTB-TK Pegatron HP/Compaq name: Truckee

  PIC of the motherboard link: http://support.hp.com/us-en/product/HP-Pavilion-HP E-h8-1000-Desktop-PC-series/5080764/model/5117795...

  Original HP installed: AMD Radeon HD 6570 (Bronco) graphics card 1 GB Model: 648533-001, SP # 659355-001

  Link video card PIC: http://www.ebay.com/itm/111761368505

  Nothing has been added/modified recently real system.  Last change was the beginning of the year 2015, which was a new 2 TB HDD and added however problem memory only started about 3 weeks ago.  The Interior has been cleaned (diffuse can)

  600W Μatx Estar v5 HF PSU (Petrus)

  Information about the current hardware out of the Power Supply Unit

  Switching power supply
  Model: DPS-600WB A
  Part number: 633186-001
  600W power MAX

  Output: DC output rating (new Corsair PSU)

  + 12Va = output DC 16A = + 3.5V / + 5v / + 12v /-12v / + 5vsb

  + 12Vb = 18 a Max Load = 25 a / 25 a / 51 / 0.8 a / 3a

  + 12Vc = 12 a Max comb = 130W / 612W / 9.6W / 15W

  + 12Vd = 10A power Total Power 650W

  + 16 5.08V = side of AC input

  + 3, 3V = 15 a AC input: 100V - 240V

  + 2 5.08Vsb = current: 10A - 5A

  -12V = 0.3 frequency: 47 Hz to 63 Hz =

  Entry:

  100-127V ~, 50-60 Hz, 10 a

  200 - 240 v ~, 50-60 Hz, 4A

  You are welcome.

  Although there is a limit to the amount of power that is needed to power your computer, it uses only the amount of power it takes to power the computer correctly.  The extra power is kept in reserve for the purposes of art.  Thus, you cannot really bad the computer with extra power or amperage.  You can sleep on this point.

  Indianaak wrote:
  

  Thank you very much for your quick response, I wasn't getting anyone to answer the previous post.

  If your saying these HP spare parts are not exclusive to the company?  Some connectors may be owners, but most are not.

  It should work then?  Yes.  I've recommended hundreds of the PSU in the years I've been helping on the Forums; in fact since about 2002.

  How about the input/output & amperages of note that I registered?  As I understand not all this jargon, I want to assure you that I have / using correct notation for my system.  I don't want to fry one of my compondents with to much amperage.   Well, either I did something wrong installing or this power supply is a dud then.  Read my explanation at the top of the page.

  As I said before I pretty sure I had all the right connections, what can you tell me if it sounds right for you.  I have pluged in both connectors wired on the motherboard which were the main ATX 24pin power connector and the EPS/ATX12V 8 pin which I shared and pluged a piece of the cable labeled 'CPU' in slot 4 pins on the montherboard labeled ATX CPU.  Regarding the other split 4 pads, I don't see anywhere, it could be pluged into the motherboard.  If two 4-pin connectors were even marked, it should be good.  However, you can try to plug the other 4 pin instead of this, just to make sure that the right pair is connected to the processor power.

  My AMD Radeon HD 6570 1 GB graphics card is the type that is fed through the MB so I didn't use any of the PCI-E cables 6-8 poles.  It is very good.

  And so the only thing I had left that I have pluged the compondents of Sata cables that was my Bluray burner, my 2 TB hard drive and my USB 3.0 card.  They are very frank.

  Yet once again being installation of hardware in my system let me ask hopefully not a stupid question, but when you connect compondents Sata cable, you must have the plug-in in a particular order of wiring compondent or how do you?  I don't check the specifications of your power supply, but I think most of them have a single 12V rail.  If this is the case, you don't have to connect them to any order.  If there are two rails, it is best to divide the power of each rail.

  On my old PSU, it has an extension cable SATA used to connent card USB 3.0 which is pretty tightly squeezed between graphics card and sound card, so I guess I could use the extension cable with the new PSU POWER Sata wiring without any compatibility also publishes, right?  This should be no problem I can think of at this point.

  Thanks again for your help, I'll probably will try and plug it once more and see if I can make it work.  If this does not work for now, I strongly suggest that you contact Technical Support of Corsair for help.  They are the experts on their products and grab any errors that we do.  It is very difficult to diagnose a problem by far.  When you have done with this project, you will no longer be the excuss you are a novice. You will have a lot of knowledge that you did not when you started.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Pavilion HPE-310 t Power Supply replacement - please help!

  OK, so I have a Pavilion HPE-310 t, (MS-7613 (Iona-GL8E) motherboard) and I want to replace the original PSU (300 watt) for a 500 watt so I can install a better video card. I looked at the harness and they look like I can put in a general diet something like this:

  http://www.Walmart.com/IP/13812566?adid=22222222227000381035&wmlspartner=wlpa&wl0=&WL1=g&WL2=&WL3=13...

  If im wondering if the gneral supplies will fix the case... Thank you very much

  Yes, the Thermaltake TR2 500W ATX12V power supply you linked to should fit in your computer case. Also consider the Corsair CX500 and CX600. Two of these power supplies are highly recommended and are known to fit in many cases of HP computer.

• HP Pavilion HPE h8 - 1380t CTO: compatibility problems, ask questions about knitting-by-turn or possible motherboard replacement.

  I recently baught an EVGA GTX 1060, as this 630 became quite long in the tooth and I thought that I would try to future proof myself a little as the rest of my components seem to be working very well.  However, I can't get the map to work correctly on this particular computer.  Oddly enough, I can get past that screen startup finally after several short beeps and let it sit, but it takes fowever to reach the office and clearly is not executed properly that the resolution is wobbly and software from Nvidia cannot even detect the card.  I guess I had got this far because of the onboard graphics of some sort, but AFAIK this motherboard which lacks.

  I know that the card works fine as I tested it in my other Tower, so I struggled to find a solution.  So far, it seems that the problem is most likely the motherboard, as HP does not have a new BIOS for it since the beginning of 2013 (which I did go ahead and install it).  If true, I find myself with either two options, it seems that the ditch system, entirely or find a motherboard that works with all my old components.  I'd rather not have to empty this workaholic, when all other parts work great, if it is not a work around I would like to know if there are motherboards I could pass that would work with the rest of my components.  Normally I would not bother with even apply for, but I hear a lot of chatter on HP PCs pre-constructed having compatibility problems.

  I bought this computer there is in the case of four years that I would be able to update as I do with any other PC, but I didn't know at the time that HP has a tendency to not update the BIOS settings for anything beyond a year which I admit is incredibly frustrating.  What is done is done however, and I want to make this work without having to clear the entire system.

  Desktop HP Pavilion HPE h8 - 1380t CTO

  Model #: B4J28AV
  Serial number: 2MD2290502

  Motherboard: 2ACE "Pittsburgh" Pegatron Corporation

  Processor: Intel Core i7 3820 3,60 GHz 'Sandy Bridge - E.

  RAM: 10 GB of DDR3 memory

  GPU (stock): Nvidia GeForce GT 630 (this is replaced by the EVGA GTX 1060)

  @Faver, welcome to the forum.

  Your problem is the BIOS.  However, it is because the 1060 GTX requires UEFI in the motherboard instead of a standard/Legacy BIOS.  HP didn't start using UEFI until mid-October 2012.  The BIOS may not be upgraded in the UEFI.  The last cards only not for UEFI were the GTX 660/670.

  MSI made cards with a switch that can be used with a Legacy BIOS or UEFI.  If you decide to go this way, you must contact their Technical Support to help them choose the best card for your system.

  The upgrade of the motherboard can be a problem.  HP has taken advice their specifications.  Therefore, they are not necessarily the same as the commercial versions.  Please make sure that the holes in the motherboard matches the accessory in the case.  In addition, some members have had problems with the connectors in the connections case before, for example, the power button.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP Pavilion HPE h8-1111: Deffective WLAN Card

  I've had a few confusing issues with my internet connection for a few weeks now:

  My computer seems to detect wifi networks (they appear in the Network Manager), but fails to connect because of an unknown factor.

  Basic troubleshooting informed me that wifi wasn't the issue (other devices could connect to) and it turns out that my computer could sometimes reconnect by mmee after a few hours (weird right?)

  This time it does not resolve itself. I tried to update my WLAN card through my laptop adapter, so the drivers via a USB key. Nothing worked (maybe bad drivers?) I've tried a few)

  My network card is a mini Broadcom 802.11n using magnetic antennas of the card. (youd cloth found in a laptop essentially...) I have little or no knowledge more than I could translate from the web on this kind of hard\software. I am at a loss.

  [Also, I've seen a few threads recommending the driver intel update of software, but it needs a connection to work its magic...]

  Hi @arnaud34,
  
  Welcome to the Forums of HP Support! I understand that you have problems with your wireless connection and I'm happy to help you.

  Is that something WLAN adapter that you added or the original map?

  The Support page and drivers for your computer model: PC desktop HP Pavilion HPE h8-1111

  I would recommend that you try the following to see if you can get a stable connection. If at the end you still have nothing so it may be that the card is bad, and a replacement is necessary.

  Troubleshooting your wireless network and Internet access (Windows 7)
  
  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Forget the network: (Windows 7)
  1. press start.
  2. tap manage wireless networks, click on the application at the top of the start menu.
  3. right click on the network, and then click on remove network.
  4 confirm the warning by clicking OK.
  
  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  Please let me know how it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• HP Pavilion HPE h8-1234: upgrading the 7450 Radeon HD Nvidia GeForce GTS 450

  http://support.HP.com/us-en/product/HP-Pavilion-HPE-H8-1200-desktop-PC-series/5187019/model/5231572

  I would like to replace the default Radeon HD 7450, which was built in desktop and replace it with a Nvidia GeForce GTS 450, my question is, is it compatible with my motherboard? Everything in the desktop computer is the same, except that I replaced the power supply with a Corsair CX600. As is all other compatible with the motherboard Angelica 2 graphics cards? Thank you!

  Shadgam, welcome to the forum.

  New after the 640 GT video cards require UEFI in the motherboard instead of the standard BIOS.  HP didn't start using UEFI until mid-October 2012.

  I see no reason why the GTS 450 (see card) is not working on your computer.  Your motherboard has a PCI Express x 16 (Gen.2) slot.  You can always call the manufacturer's Technical Support to make sure the card you have chosen will work.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion HPE h8-1050z-switch series

  Hello, my computer below has a button/power switch that fell in and can either be pressed.

  HP Pavilion HPE series

  MODEL: h8-1050z

  SERIES: [edited by Moderator serial number]
  PRODUCT NUMBER: LP026AV #ABA

  Need part numbers for switch/button replacement sets.

  Please advice

  Thank you.

  I suspect it's the button broke off his mount. It's just a piston. The actual switch is lower. You need to remove the real top panel to decide the issue. Here's a guide. See p 2 and 3. After removing the side panel and the front panel, you should see the screws in the top panel. You might be able to fix it to the mount.

  If this is not the case, a replacement Panelcan be purchased here.

• Pavilion HPE series, LP028AV # a: Windows has not started, but ended up with Recovery Manager without control

  When I started my desktop computer, Windows did not come to the top, and then he came to the Recovery Manager window. So, I wanted to select System Recovery, but the wired keyboard seemed to be locked and so was the wired mouse.  No selection is possible on the window. Please help me to unlock the keyboard in order to proceed to the recovery of the system or to correct the problem.  I also tried to restore the system from the recovery disks, but the keyboard and mouse have been locked as he came to the Recovery Manager window. Here it is a little recap of my office-info:

  Product name: Pavilion HPE series

  Product number: LP028AV #ABA

  Model number: h8 - 1070t

  Thank you for your help in advance.

  Jay

  Hello.

  After replacing the batery, I got a black screen. But I discovered that the cable from the monitor was not completely connected after that I moved the PC and the monitor. Once I fixed and restarted the PC, keyboard and mouse are animated.  I'm currently running System Recovery.

  Thank you for your excellent support as well as your patience.

  Jay

• Pavilion HPE: Obtaining a recovery media for your desktop HP custom build

  I replaced my SSD drive failed in my HP Pavilion HPE I bought in July 2012 and seeks to
  do a system restore for a restoration of the value I created before the break.  I start the PC with the first DVD-R disk in the drive (by car I used for the set), press ESC to enter the boot menu, navigate to the Boot Menu to select the /SATA2 option Legacy Boot Sources/ATAPI CD/DVD Drive option.  The result I get is:

  "Intel UNDI, PXE - 2.0 (build 083)
  COpyright (C) 1997-2000 Intel Corporation
  For Atheros PCIE Ethernet Controller v.2... 1.9.9(08/12/11)

  Check the connection of the cable!

  PXE - M0F: Exit Intel PXE ROM.

  ERROR: no boot disk was detected or the drive failed. »

  The drive fail as failure.  I read on another computer very well (open files, view file properties, copy the folders and files).  For a smile, I put an old XP Recovery disk in the drive of the computer, I'm trying to restore and he was able to read that.

  Whatever it is, I try to order recovery disks by following the link on this page:

  http://h20565.www2.HP.com/hpsc/doc/public/display?docLocale=en_US&docid=emr_na-bph07143&sp4ts.Oid=52...

  This page asks me to provide a specific model number.  I don't have because it is a customized version.

  It's on my list of selection information:

  > YOUR
  > CUSTOM HP PC
  > h8t
  > • Windows 7 Professional (64 bit)
  > • 2nd generation Intel Core i5 2400 quad-core
  > processor [3.1 GHz, 6 MB cache]
  > • FREE 6 GB DDR3 1333 MHz SDRAM [2 DIMMS] UPDATE
  > 4 GB
  > • 1 TB 7200 RPM SATA hard drive
  > • No secondary hard drive
  > • SAVE $40 on Microsoft Office Home and Business
  > 2010
  > • No additional security software
  > • 1 GB DDR3 AMD Radeon HD 7450 [HDMI, DVI, VGA via a
  [> adapter]
  > • 300W power supply
  > • DVD SuperMulti burner
  > • LAN wireless-N (1 x 1) card
  > • 15-in-1 reader cards, 2 USB 2.0 (front), 2 USB
  > 3.0 (top)
  > • No TV Tuner
  > • Beats Audio (tm) - a built-in studio quality sound
  > • Premium HP keyboard and optical mouse
  > FREE • Adobe Premiere elements and Photoshop 10 [$149
  [> value]

  If I can't use the recovery set I did, how can I get a proper HP for my setup recovery disk?

  Hello

  A 240 GB SSD is large enough for the support of HP recovery work.  Order the HP support.

• HP Pavilion HPE h8 - 1070t CTO need case fan

  HP Pavilion HPE h8 - 1070t CTO, product number: LP028AV #ABA

  After an error message, on the fan and case fan noise I replaced the AVC DS09225R12MC234 DC 12V case fan 0. 3A with a Startech.com FAN9X25TX3H case fan.

  A program to monitor I have shows an increase in rpm of the system another fan. I'm trying to find out if my new fan is correct or adequate propper case fan.

  Hi checkit, as long that all fans are working and they doesn't make unusual noises or work allways on the maximum RPM is fine, Adi.

• HP Pavilion HPE h8-1216 Desktop PC/new Nvidia Geforce GTX 650 will not install

  HP Pavilion HPE h8-1216 Desktop/windows7

  Have already replace supply 500watts power when I put the old GT520 it works very well put when I replace it with the

  GTX 650 that I just get the HP welcome screen, nothing else seems to work without a mouse and Esc just make the screen off

  and the right of return to the HP welcome screen.   Is there something that prevents the installation of the card?

  Check the ASUS PCIe - x 16 video cards.

  It all depends on your budget

  The following map has inherited by default vBIOS. Check the specs on the ASUS cards.

  

• Pavilion HPE h8z cannot connect to the router to 1000Mb

  Pavilion HPE h8z

  Windows 7 (all updates including updated network driver)

  Router: RV220W Cisco

  Cable: Cat 6

  Any new system.  All the network settings on the PC and the router are "out of the box '.  The system will not connect to 1000 Mb (Gigabit), even if the other 2 on the same router (1 XP, Linux 1) connect without any problems.  Swapped cable and ports without difference,

  And before anyone asks, it that a Realteck Gigabit Ethernet chip on the motherboard.

  Tech came out at 08:00 as expected.  Replaced motherboard.  We have video, we have Gigabit Ethernet.

  HP should really look at this whole incident.  In addition to taking almost 4 weeks to fix the problem and let the client without computer running for more than 10 days, this event has cost thousands of dollars support HP.

  Process of elimination said that it was a hardware problem. IMHO, this kind of problem should have been taken before his departure from the factory (certainly not a HP has / operates the plant).

  If HP has spend this amount of resources to solve this kind of problem, it is not surprising that they want to get out of the PC business.

• Pavilion HPE H9-1130: install the firewire card correctly into the slot of the motherboard correctly

  Hello, for my HP Pavilion HPE H9 1130, how to install the correct firewire in the motherboard slot card OK in OS Windows 10 x 64 / x 64 processor? And what video software system can I download to recognize my Panasonic 100a camera AX?

  Thank you. Followed your instructions. And it worked perfectly. Thank you. Even if I have Adobe Prem Pro, I downloaded MS Director and put 9 drivers after installing the PCIe card. Then it worked perfectly to capture video from a FireWire camera. Thank you once again!

• HP pavilion hpe h8-1020: evga geforce gtx 950 in hp pavilion hpe h8-1020

  Hello guys I have a hp pavilion hpe h8-1020 and I am looking to upgrade to a nvidia gtx 950 is it compatibile, what I need to supply?

  Hello

  There is a unknown specification for your motherboard that will prevent you from installing a new 3.0 PCIe x 16 graphics card. Maps 3.0 is backward compatible with PCIe x 16 2.0 slots. Your motherboard may have a PCIe x 16 1.0 slot. None of these options below works on your PC if you have PCIe x 16 version 1.0

  The Radeon HD 6570, an option to purchase, is a PCIe x 16 card USB2.0. You can have a 2.0 slot. It is unclear when we look at the characteristics of HP for your PC.

  I got a HD 6570. You could not install drivers from AMD with the version of HP of this card. You need to use the HP drivers. It is possible that this card is not a 2.0 card even if the consumer version is a USB2.0 card. We can only guess.

  MSI is rolling out hybrid Nvidiacards soon. Try anything tangible yet seen. NVIDIA is slowly releasing the 1000 series cards that require less power. Maybe some OEM will also include hybrid versions that will work on your PC any time.

  The 900 series Nvidia graphics cards need the UEFI BIOS.

  Your PC has a legacy BIOS.

  You have a 300 Watt power supply. You will have to upgrade from food to run a card AMD and respect the strict minimum if you can install a TG 640 GDDR5 map.

  You may be able to install (you need a PCIe x 16 slot 2.0) Nvidia 600 series cards or watch hybrid of AMD cards by Sapphire.

  AMD cards are longer and require larger power supplies.

  You should check that you have the power and the room to install two graphics cards. The cards are also double slot. You will need to verify that you can install a card double slot. Even once, you need a PCIe x 16 slot on the motherboard 2.0.

  See you soon!

• My Pavilion HPE h9 - 1120t Phoenix Bios does not display Options for virtualization technology

  I have a Pavilion HPE h9 - 1120t Phoenix with Intel Core I7 - 3770 k and Windows 7 Professional 64-bit operating system.

  I checked that my CPU indeed does support virtualization technology, and it does according to Intel. However, when I try to run a 64-bit VM in VM Ware player, I get this message: "the host is capable of VT, but VT is disabled.

  When I checked the BIOS to enable VT, I have been unable to find a setting for VT option can I update the BIOS to use VT?

  Hello:

  Have you checked in the Security menu Security / Unit of material?

  This is where the adjustment would be if she has one, and it is disabled by default.

  Paul