HP PSC 950 All in One Printer: function of enlargement

Similar Questions

• Windows RT and HP PSC 1510 all-in-One printer connection

  Hi, I have a Windows 8.1 RT (Microsoft Surface 2) Tablet and HP PSC 1510 all-in-One printer cable. Now when I plug the printer via the USB port, there is no driver who finds himself to make this printer work with my camera. Does anyone have this problem or solutions? I tried to look at HP support and nothing there has been useful.

  Hello

  I'm afraid that the printer is not supported on Windows RT, as you can find listed in the following support document:

  http://support.HP.com/us-en/document/c03168175

  Kind regards

  Shlomi

• HP psc 1210 all-in-one printer: HP PC all-in-one printer

  Printing test page fine.  Prints the first page of the document very well.  After than that, each page becomes lighter and blurred until unreadable.  This "bad s.  Printer is several years old and has been the impression so far.

  Hello @bdr777,

  Welcome to the HP community!

  I hope you have a pleasant experience here.

  I would like to help with the discoloration print issue you have with your HP PSC 1210 all-in-one printer, when printing from your computer Windows 8.1.

  Could you try to make 3 copies of something on the printer for me? If the three pages of fine print, then we know that the problem is related to the software on your computer. If the pages are starting to fade and blur, then we know that the problem is probably with the printer cartridges.

  Are the cartridges you use genuine HP? Can you check the date of guarantee on them for me if they are? If they are relatively old cartridges, the nozzles down can be a bit clogged and start getting muddy upward while you print. (This is particularly likely if you use the printer very rarely).

  If copies are still faded and blurred, try these steps to clean the cartridges:

  1. Open the all-in-one with the power on and then remove the ink cartridges by slightly pressing the cartridge while pulling gently toward you.
  2. Inspect the ink cartridge ink nozzles and contacts for the accumulation of debris and ink.
  3. To clean build-up, dip a q-tip in distilled water (or water if distilled water is not available) and press the remaining water from the swab.
  4. While now the cartridge by the sides, as shown in Figure 3 below, gently wipe off any buildup of debris.
  5. Reinsert the ink cartridges and perform the alignment of ink cartridges.
  6. Print a test page to check the ink cartridges and rinse any remaining accumulation of the nozzles of the cartridges.

  

  -Source

  If the copies to print without any problem, try to download the HP printer installation wizard to make sure you have the latest drivers for your product.

  I hope this helps!

  Please reply to let me know if we have solved the problem.

  

• HP PSC 1510 all-in-one printer

  My OS is Windows 7.

  I tried to get this printer is installed.  Error messages ' print spooler does not "or" error in C:\program files analysis file (X86\HP\Digital imaging\bin\hpqscloc\103.xml "."). sevveral times it worked for a few pages after his farm and re-booting printer displays "printer troubleshooting."

  Hello

  Please contact the Microsoft Community Forums. I understand you when you try to install the printer you get an error message indicating the print spooler does not.

  Follow the steps for troubleshooting instructions.

  (1) how you try install the printer?

  (2) using a CD/DVD to install the printer?

  Follow the steps for troubleshooting instructions.

  Method 1:

  I suggest you to refer to a link.

  Diagnose and automatically fix problems printing and printer.

  http://support.Microsoft.com/mats/printing_problems/

  Method 2:

  I suggest you the link and download the drivers from the manufacturers Web site and are trying to install.

  HP PSC 1510 All - in - One Printer Drivers & Downloads.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&lang=en&LC=en&product=428800

  If still the problem persists after you perform the steps of troubleshooting from the link and if you have questions related to Windows, please do not hesitate to answer us, we will be happy to help you.

  Thank you.

• HP PSC 1317 all-in-One Printer Windows 7 64 bit driver could not install

  Hello

  HP PSC 1317 all-in - One Printer driver Windows 7 64 bit does not.  I tried to install the driver after the incredibly long download (362 MB) to be told by windows that there is no driver.  I have uninstalled the software 3 times and reinstalled.  I unplugged, disconnected, re-downloaded and re-installed.  I downloaded the 64 bit vista drivers (they do not work).  I came to your site to seek support that is denied to me because the printer is out of warranty.  Unless, of course, I want to pay for it.  Which I did, after spending a considerable time (see above) trying to get it work on Windows 7.  Last thing to install on another machine, which I just do exactly the same result, and no sign of anyone else having the same problem everywhere.

  Now what can I do to get this printer to work?

  

  I solved this by using Windows update, which then installed a driver in the end.

  This was not a great experience.

  Why have a download for the version of 64-bit Windows 7 for this printer that puts all the other bloatware of HP but does not contain any driver.  Then you perform the update from Microsoft to get a signed HP driver?  Why can't the HP driver actually be content in the download presumed HP so you can Dodge all the crap software I just uninstall anyway.  A huge waste of time and effort.  Two weeks to solve a problem that should have been done in twenty minutes.

  Not good PR client on any level.

• Problem with my HP PSC 1610 all in one printer of the series which is printing pages in the right order.

  Basically I have the HP PSC 1610 all in one printer. I know not what has happened, but in some way, when I go to print a document of site Web etc, use the printer to print the last page first and keep printing until the 1st real page printed would be changed, which would print on top printed pages.

  My problem is now, it's actually print the path opposite, now it prints the 1st page of first and last last page, which means when I pick up all the printed pages, I then have to sort the page numbers in the correct order.

  Now, I use my printer waste dumps, I print a lot of game documents such as guides etc.. Now if I was just printing pages 1-5, I'd be fine with it, but at this current moment, I was printing guides with more than 50 pages, which really saddens me to have to keep sorting out pages of paper for good order.

  I must say that it does print no pages in a random order, which means like printing, for example, 10 pages, it does not print the page number 6, 2, 5, 8, 3, 10, 1. It is actually printing the pages in the following way, page 1, 2, 3, 4, 5, 6, 7, 8, 9, 10. (When it's over, page 10 is one who is on top of the stack), but I really need to put it so that it will print the pages in the following order, p. 10, 9, 8, 7, 6, 5, 4, 3, 2, 1. (So at the end of printing, the pages of issue 1 is actually on top of the battery), which will allow me to simply staple the pages without the need of haviing re - sort the order of the pages in the correct format.

  I have all my print programs installed as Director of HP and others, so I can change main settings of printers, but I looked through all the preferences main page tabs and I don't find the option to change the printing order of pages.

  I really need help to set my printer settings to print order in the way I need to, but I don't know where the actual parameters are to change this option, and I tried to do an actual search on Google, but I use too many words, search results do not end up giving me instructions that I need He is always giving me other things, more like excavations at random on everything related to my printer and I can't be bothered, working all day to get the good looking, lol. Can someone give me please the instructions I need to set the print order, I need it to be.

  Thanks in advance for all who are able to provide me with assistance.

  Thank you

  Alison Black.

  LIVE FAST, FIGHT HARD CLOSE.
  HUSTLE, LOYALTY, RESPECT

  John Cena (WWE Wrestling Heavyweight Champion)

  Hey

  HP have the customer.

  has attempted to call them abt the question because I'm clearly useless with this technology * beep *.

  but fisgured this is a setting of the printer.

  so if you have the HP SOLUTIONS CENTER's new installed.

  down the down theres a SETTINGS tab click on it.

  go to the PRINTER SETTINGS, once you have clicked on a new dialog box appears.

  the first tab (by following my printer settings ive got a HP PSC 1311) must be ADVANCED

  Click on that, the last option should be OPTIONS AVAILABLE and bloody, WHICH PAGE ORDER WE WERE looking for THAT PERSON DO CAN TELL US ABOUT.

• PSC 1610 all-in-one printer: PSC 1610 will not print

  HP PSC 1610 all-in-one

  No including photographic paper feed and the following messages are received: paper jam or paper. This is not correct. Jam has recently replaced; all paper rolls have been cleaned up with water. Any advice would be appreciated.

  Thanks for your reply. I think you are right to say that it is a hardware sensor problem. In the circumstances, I'll buy a new printer/scanner/copier.

• I have a problem with the HP psc 2210 all in one printer.

  My printer is an hp psc 2210 all-in-one

  All main buttons are flashing and the message on my reading of the printer (Remove and check cartridge) t - it means to clean?

  Hello

  Equip your number of printer model to this site of HP drivers and support for this information and follow the troubleshooting steps for it.

  http://WWW8.HP.com/us/en/support-drivers.html

  Or ask in the Forums of HP's Support.

  http://h30434.www3.HP.com/PSG/

  See you soon.

• HP PSC 1410 all in one printer scanner does not work

  My printer, HP PSC 1410 all-in-one works fine as a printer, a scanner and a copier until I had a virus and had to reformat.  I have the original HP for the printer drive, downloaded the software undated and have loaded, deleted and reloaded the software 20 times.  The printer and copier works well.  Microsoft appears saying that scanner drivers are not certified, etc. and I can't scan to work.  I had put in hundreds of hours trying to get this to work.  I am 71 years old and I already have the computer work for my company 18 years ago.  My inability to solve this problem that bothers me more than anything else.  I need some young soul to help me that whip.  I don't buy a new computer or upgrade to Windows 7 until I fix this.  It has become a challenge, but I need help.  Kenny:

  Hi KennethPlaisance,
   
  Method 1: HP has created an update to update the driver to scan and fix the problem. Check if it helps you to fix the problem.
  For more information, see:
  The digitized files disappear after scanning with HP Solution Center
   
  Method 2: Use the diagnostic utility scan to fix the problem automatically.
  Visit this link to download the utility:
  "Scanning device could not be initialized" and related scanning errors display in Windows XP, Windows Vista and Mac OS X

• Scan HP PSC 1410 all in one printer works well, does not work with Win XP SP3

  I am well satisfied with my computer HP 2006, Win XP SP3; However when I had to reformat the HP PSC all-in-one printer that works well will analyze any more.  Microsoft says that it does not recognize the drivers for the scanner.

  Try to download software and software updates of the HP Web site.  See if that helps.

• Need to download a driver for my HP psc 1205 all-in-one printer

  My HP psc 1205 all-in-one started to play up.   It takes forever (if there is one) to get a page to print.  I end up having to go to services.msc, select "Spooler" and then "restart".  It is said that said in the Description column "files charges to memory for later printing.  I want to just print a page.  I can't find my original disk to restore the printer.  I have check the print queue is empty (no file waiting to be printed).  When I master and P to print the report says 'Idle '.  What can I do to get to normal printing.

  The printer goes back to late 2003. Driver for Windows 7 support and beyond, it is everything that Windows Update has and that's going to be the absolute essential only.

  See here... http://support.HP.com/GB-en/search?q=HP%20psc%201205&filter=-1

  You'd want to consider purchasing a newer model which seeps pilot full support of its manufacturer... :-)

• HP psc 2210: clear jam on my hp psc 2210 all-in-one printer

  The lights on my printer and the message says: "open the door.  "Clear carriage jam, and then press ENTER.  I do not see a "jam", opened the door and press enter several times.  I still can not reset unplugged machine from one day to the next.

  I think the cartridges are "stuck" on the side of the machine and they are unable to drag in the middle.  Can someone tell me how to fix this jam?

  Would be very grateful for the help!

  Renee'

  Hi @sreneecesand welcome to the Forums of HP!

  I see that you are having problems with jam.  I would like to help!

  I recommend starting by remove (if possible) ink cartridges and perform a power reset the printer.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.
  
  I would also say to following the steps outlined in this document:

  A display of the Error Message of "open door, clear transport jam, and then press enter" for HP PSC 2170 2100 and 2210 all-in-One Series Printer "

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• hp psc 1315 all-in-one printer has a memory/hard disk?

  I want to have a printer all-in-one hp psc 1315. is there a hard drive than the personal information?

  Hello

  With a few exceptions, most of the printers have not memory to hold the print jobs (which are not cleared by simply turning off the printer).  The only thing that can be stored in some printers (with fax capacity) is telephone numbers in the fax log.  I don't think that the PSC 1315 has a fax, but if you really want, you can do a hard reset I think that you can unplug the printer from its power source and by holding the power and Cancel buttons down.  You may see a flashing of the lights. That should do it!

• What is hp psc 1355 all-in-one printer scanner copier compatible to be used in the WINDOWS XP operating system?

  I have a hp type copier printer scanner hp 1355. I need a driver (software) for this.  If the HP all-in-one device is not suitable for use on WINDOWS XP, is it possible to use hp 1355 in the WINDOWS XP operating system? Thanks FOR YOUR HELP.

  Hey Fed-Up-with-HP,

  Try using the brush included in the CD or download. Let me know what you find?

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the uninstall_L4 (exe or Bat)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-23606-3&cc=US&DLC=en&LC=en&os=228&Product=306898&sw_lang=

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. run the uninstall_L4 (exe or Bat)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-23606-3&cc=US&DLC=en&LC=en&os=228&Product=306898&sw_lang=

  10. run the download to reinstall the printer

• My Mac does not recognize my PSC 1610 all-in-one printer.

  All of a sudden my mac does not recognize my 1610 printer all-in-one.  I think it may have something to do with the system 10.8.2 upgrade but I'm not sure.  I followed the instructions and uninstalled and reinstalled the software.  Software update does not seem to think that miss me anything, no update is listed.  Nothing has changed other that the OS and I use this computer and the printer for 3 years.  No printer appears in the list of system preferences.  Error when I try to print is 'not connected printer.

  Hi beaumast,

  Have you tried using a USB cable?

  If you tried it on your friends computer and got the same experience there is a possibility that the USB port on the printer has malfunctioned. Here are some links that you may find interesting if you consider upgrading your printer.

  HP trade-in program

  Current for sale Photosmart printers

  HP out of warranty of the Support Options for selection of printers HP