HP Touchsmart 600-1050 blue screen to install Windows 7

Similar Questions

• Computer crash - blue screen after installing windows updates

  After you have installed Windows updates waiting on the computer earlier this week, we were not able to get the computer working again.  We were asked to back up and restore the factory settings, which we did.  It instructions update you Windows. When we download the updates it crashes again.  Does anyone know if there is a problem with one of the recent updates that we should avoid so that we our computer working again?

  Hello

  Since you are quite sure this is an update to the source of the problem I want to troubleshoot using this method.

  Control Panel - Windows Updates - upper left settings - set to download but allow you to install them.
  To operate the system and see if there are problems.

  If no problem try to apply updates in small groups or even one at a time, depending on how
  There are many. Beware especially of driver updates that may be older that you have or
  those even incorrect.

  ---------------------------------------------------------------------------------------------------------------

  These can help to solve the problems of update.

  Control Panel - Windows Updates - lower left Installed Updates - uninstall or change

  Or

  Remove an update
  http://windowshelp.Microsoft.com/Windows/en-us/help/182043da-fc3e-4220-AFBC-d9b09f2b2a1a1033.mspx

  Or

  The problems with the removal of updates
  http://windowshelp.Microsoft.com/Windows/en-us/help/5a319824-5cb5-493d-9151-9a97d0f565b61033.mspx
  Or

  How to uninstall updates in Windows Vista
  http://www.vista4beginners.com/how-to-uninstall-Windows-Vista-updates

  Disable or hide optional updates on Windows Vista
  http://www.howtogeek.com/HOWTO/Windows-Vista/disable-or-hide-optional-updates-on-Windows-Vista/

  ============================

  If necessary, you can get free reports of incidents.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• VN7 - 592G blue screen after installed Windows 10 anniversary update

  Hello

  This week I installed the last 10 updated Windows on my laptop VN7 - 592G (tried build 1511 upgrade and clean installation, too), however, I still have the Blue error screen. I can't use my laptop, or to do anything because of the Acer is not kept up-to-date of pilots.

  Of course, I installed the drivers of the last Acer of acer.com but Realtek Audio does not work so my computres crashes at startup.

  ==================================================

  Dump file: 080316-7609 - 01.dmp

  Crash time: 2016. 08 03. 0:18:11

  Bug Check String: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

  Bug check code: 0x1000007e

  Parameter 1: ffffffff "c0000005

  Parameter 2: fffff80e'adc68a41

  Parameter 3: ffffb281'd19376a8

  Parameter 4: ffffb281'd1936ed0

  Caused by the driver: RTKVHD64.sys

  Caused by the address: RTKVHD64.sys + 48 has 41

  Description of the file: Realtek (r) High Definition Audio function driver

  Product name: Realtek (r) High Definition Audio function driver

  Company: Realtek Semiconductor Corp.

  File version: 6.0.1.7687 built by: WinDDK

  CPU: x 64

  Plant address: RTKVHD64.sys + 48 has 41

  Stack address 1:

  The stack address 2:

  Address 3 the battery:

  Computer name:

  Full path: C:\Windows\Minidump\080316-7609-01.dmp

  Number of processors: 8

  Main version: 15

  Minor Version: 14393

  Size of the dump file: 411 988

  File dump: 2016. 08 03. 06:40:05

  ==================================================

  Hi all

  I'm sorry for the delay; first of all, I want to thank you all for your patience as we worked to solve this problem. Second, I have been informed that we had a new audio driver released for the VN7 - 592G, version 6.0.1.7910, and it is now available in the website of drivers and manuals.

• blue screen after installing windows update

  Original title: Windows Update system killed 13 March 2012

  After you install the updates Windows yesterday (13/03/12), the screens of the blue system at startup and in safe mode, does not restore system, saying: "a parameter is incorrect."

  Hello

  It is unfortunate to know that you need to perform a reinstallation of the operating system, but there was interference between the files.
   
  You can provide feedback if you have any concerns. Check out the following link.

  http://www.Microsoft.com/mscorp/Execmail/feedback.mspx

• Portege R500 - blue screen after installing Windows XP SP3 home edition

  * computer toshiba Portege R500 laptop *.

  * non-modele ppr50e00j00fs4 *.

  SP3 installed via update-site, received successful message SP3 installed restart... now bluescreen an impossibility to restart! Not even in save mode!

  If I try to start with the InstallationRecommandations, I get the following message:

  STOP: 0X0000007E (0XC0000005, 0XF79ED8EB, 0XF79ED7F4, 0XF79ED4F0)

  Can someone help me please?

  Hmmm. seems that this is a known Microsoft issue because I found these MS knwoldge base article:

  How to troubleshoot a Stop error 0x0000007E in Windows XP
  http://support.Microsoft.com/kb/330182/en-us/

  Microsoft has stated that:

  + These problems may occur if a system thread generates the error handler catches not an exception. You receive this error message if one or more of the following conditions are met: +.

  + If this issue occurs after the first restart during Windows Setup, or when the Setup program is finished, the computer does not have a sufficient disk space to run Windows. +
  + If this problem occurs after the first restart during the installation of Windows, or once the installation is complete, the computer's BIOS may be incompatible with Windows. +
  + Incompatible video card drivers. +
  + A chauffeur service or system device damaged. +
  + If the problem is associated with the Win32k.sys file, it can be caused by a control program remote third +.

  I recommend checking the solution proposals published on the website of Ms.

  Good bye

• TouchSmart 600-1050: touchsmart 600 1050 installed new drive sata, how can I recover disc windows 7OS home prem w/o OS

  How to recover Windows 7 Home Prem OS, after original hard drive failures. I replaced it with a new HD, but can't boot OS and does it have any disk recovery Touchsmart 600 1050, it was purchased nine walmart 2009 by me, prior to this accident, the cd/dvd-rom failed and never returned.

  The new hard drive should be of equal size or as to what you had and not the format of the AF.

  You will have to order recovery disks, if you live in the USA/Canada, call HP at this number 1-800-334-5144 and see if you can still get a set of recovery disks.  Otherwise the site worldwide: http://welcome.hp.com/country/w1/en/support.html

  If HP does not have the discs, you can get them at the computer the surgeons who have them:

  http://www.computersurgeons.com/p-18105-recovery-kit-gv405av-for-HP-model-number-600-1050.aspx

  Needless to say that you cannot get them on USB key that you must repair your CD/DVD drive to use the recovery discs.

• RTM of Windows 8 installation Fail on Touchsmart 600-(1050)

  Has anyone else had much luck RTM of Windows 8 on a Touchsmart 600 installation? My installation starts ok, but after the first reset it everything is there with the logo and the whirlpool circulating. The boot record, I checked and I have a suspicion that he doesn't get Windows to start after the reset.
  
  Anyone else facing this?

  Just for everyone to know that I finally managed to fix it. It appeared that my question was a known Windows 8 Preview version that Microsoft has released a fix for (http://support.microsoft.com/kb/2727113). Apparently, there's a bug which can cause freezing symptoms I was see and by running the command

  bcdedit/set disabledynamictick no

  due to the gel to stop. It seems that the update has been released with RTM of Windows 8, so it does not seem to have worked at least the Touchsmart 600-1050. Many other people are reporting that it didn't work either, but as long as the above command will stop the gel I'm happy.

  My installation is going well now, work all, all happy. The only thing I needed to update was the touch screen 2.6.9.0 to 2.6.10.0 pilot who has really improved stability. That and the driver for the buttons on the side of the case.

  Happy days!

• I have a Hp touchsmart 600-1050 and I also have 3 other laptops running of the internet itself, but I get a message IP address conflict.

  I have a Hp touchsmart 600-1050 and I also have 3 other laptops running of the internet itself, but I get a message IP address conflict, why? & How can I fix this problem, thanks Aldo Zapata

  An IP address conflict occurs when two computers on a LAN (local area network) or the Internet were assigned to the same IP. IP conflicts between two computers normally make one or unusable both for network operations.

  Try below methods

  1. for networks where the addresses are fixed (statically assigned) IP, ensure that each local host is configured with a unique IP address.

  2. If your computer has an address assigned dynamically, releasing and renew its IP address can bypass IP address conflicts.

  Run the following commands in the command prompt:

  ipconfig/release

  ipconfig / renew

• Get the blue screen error saying windows has shut down to prevent damage to this computer

  My sons computer is BLUE with a message saying that windows was arrested for not to damage your computer. And it is stuck on that screen. Do you know why windows shuts down his computer?

  * original title - my son computer is blue and a message indicating that windows has stopped to avoid damaging his computer. And he is not able to do anything. Do you know what it is? *

  Hello

  1. what operating system is installed on his computer?
  2 did you the hardware changes to his computer before the question?

  Perform the steps in the article and see if the problem is resolved or not.
   

  Resolve stop (blue screen) error in Windows 7

  Also check the event viewer for error logs

  Open event viewer

  What are the information contained in the logs of the event (Event Viewer)?

• reformat and reinstall Windows XP but get the blue screen on the windows configuration page

  I'm trying to reformat and reinstall Windows XP on my Dell XPS400, but I get a blue screen on the Windows installation page that says... A problem has been detected and Windows has shut down to prevent damage to your computer.  How can I make this?  I want to give this computer to my grandchildren.

  Hello

  1. why you try to reinstall Windows XP?

  I suggest you to try the steps below and check if they help to resolve the issue.

  Configure your computer to start from the CD-ROM drive. For more information on how to do this, refer to your computer documentation or contact the manufacturer of your computer. Insert your Windows XP installation CD, and then restart your computer.

  a. when the message Press any key to boot from the CD appears on your screen, press a key to start your computer from the Windows XP CD.

  b. press ENTER when you see the message to install Windows XP nowand then press ENTER is displayed on the Welcome to Setup screen.

  c. do not choose the option to press R to use the Recovery Console.

  d. in the Windows XP licensing agreement, press F8 to accept the license agreement.

  e. make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP.

  f. follow the instructions on the screen to complete the installation.

  See the following link for more details on the repair facility:

  How to perform a repair of Windows XP installation, if a later version of Internet Explorer is installed

  http://support.Microsoft.com/kb/978788

  Hope this information is useful.

• window does not go past a blue screen that says windows can't connect me

  Hi I have an older version of windows xp and that you downloaded an older version of quickbooks 2007 program a disc when it said to restart the computer I hit reboot and now my computer will display loading windows and then stop to blue screen with the windows logo, I can move my mouse but nothing happens I (use this computer very rarely) that it is an old but I still need it from time to time. help please. Thanks Rose

  Hi Rose,

  · What is the error displayed in the blue screen?

  · Provide the full error message with the error code.

  · What is the service pack installed on the computer?

  · What is the number and the model of the computer?

  Try the steps listed in the link below: how to fix a computer that does not start: http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx

• Blue Screen Driver IRQL blue screen of death Windows 7 Ultimate edition and Windows Vista

  original title: BSOD Driver IRQL blue screen of death Windows 7 ultimate and Windows Vista

  I get the BSOD, and they are different every time.

  I had originally Windows Vista on my pc (HP m8300f) and it worked fine for 3 years until last month, I started to have these BSOD.

  So I thought a new clean install of Windows 7 Ultimate would solve the problem. Well, I was very happy to get the new operating system installed, but a few hours later that darn BSOD appeared and im now distraught.

  What is my RAM? My drivers? My hard drives?

  Computer IM but I'm certainly some type of technology. I have basic computer knowledge and that's all.

  You can download minidump files and find the information system here in this zip file http://www.sendspace.com/file/mfx420

  This issue is very very irritating and has ruined a lot of my work.

  Well up to now (18 hours) my computer has not had the BSOD and what I did is that I removed 1 GB of ram for my motherboard. Their were two sticks of 512 MB. I took them both. Now, I have 2 GB of ram running in my system and had not had a BSOD or an error after you have done this.

  What is the problem with my ram? I now have 2 sticks of RAM on my motherboard and both are 1 GB each stick. What is the mix n match that causes a problem all of a sudden? My computer came with this stock of installation. I also noticed the ram I got were the brand Samsung and the other on my motherboard are another brand.

  Well idk I hope it was my problem. We'll see.

• Event of the blue screen appears in Windows 7 then start Scan, windows will try to recover from the unexpected shutdown.

  After EACH SCAN BOOT BY QUICK HEAL INTERNET SECURITY 13 time, EVENT - SCRENE BLUE PROBLEM APPEARS. THEN, WINDOWS RETRIEVES UNEXPECTED CLOSING DOWN. AND AUTOMATICALLY STARTS THE STARTUP REPAIR TOOL. IT HAS BECOME A REGULAR PART OF MY COUNT (WINDOWS7 HOME BASIC)... BUT IN THE CASE OF OTHER TYPES OF ANALYSES CARRIED OUT BY THE QHIS13 SAID, THIS PROBLEM DOESN'T SE IS NOT.  BUT WHEN STARTING THE SCANNER (AFTER COPLETION) REPORTS AS FOLLOWS:

  PROBLEM SIGNATURE-

  PROBLEL EVENT NAME - BLUE SCREEN

  O.S VERSION---6.1.7601.2.1.0.768.2

  ID LOCAL - 16393

  MORE INFORMATION ON THE PBOBLEM-

  BCCODE - 1000008e

  BCP1 - 80000003

  BCP2 - 8EA434134

  BCP3 - 8A6B4318

  BCP4 - 00000000

  SERVICE PACK - 1_0

  PRODUCT - 768.1

  INTERESTINGLY, WINDOWS DEFENDER IS DISPLAY AFTER FULL SCAN MY COMPUTER WORKS NORMALLY.

  PLEASE THINK FOR ME.

  Hello

  This problem may occur if the antivirus program is not properly installed on the computer, or if it is not updated with the latest updates.

  I suggest you install the latest updates of security software and check if it helps.

  You can also try to Uninstall and reinstall the security software and check to see if the same problem happens.

  If the problem persists then I recommend you contact with the help of Internet Security Quick Heal .

  More information: Resolution error blue screen in Windows 7.

  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  Important: all performing hard disk the disk check if bad sectors are found on the disk hard disk check is trying to repair this sector if all available on which data may be lost.

  (Try all the steps except the re - install Windows 7)

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• HP Touchsmart 600-1050 - Light flashing - unable to Post

  I have a 600-1050 running Windows 7 TouchSmart I work for a friend.  He was surfing the web and said that when he clicked on a link in Google, the screen in black and ambient light began to blink.  I thought it was great, but of course, he was right.  As soon as you plug it in, the ambient light begins to blink approximately twice per second, very fast.  I'm guessing this has something to do with the power, but I don't know where to start or even if it is worth trying to fix since the computer is more than 4 years old.  I searched online and can't seem to find someone with a similar situation, so I hope that this forum is useful.  Thank you!

  The ultimate resolution for this question was intended to replace the motherboard.  Thank you for all your comments!

• Satellite A205-S5804 - blue screen after installing XP

  Hello.

  I tried to do it twice in vain both times. I have the XP disc and I used it on my desk before so it does not work. Installation is finished and after it is done XP load and there is this blue screen that appears as a fraction of a second and I'm unable to read and then restart the PC. Very frustrating.

  I'd like to really all the help that you can offer me. Toshiba customer service told me that this model only supports Windows VISTA, but there must be a way. Please help me.

  Moled number psaf3u-0nr00v

  Toshiba Satellite A205 - S5804

  Hey,.

  Do you also have problems with the Toshiba Recovery disk or the Windows XP disc?

  The problem is probably related to the drivers SATA may have installed XP correctly when you change the HARD drive in the BIOS from AHCI compatible?