I can't connect to a modem cable with ethernet...

Similar Questions

• I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

  Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

  The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

  Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

• Upgrade to modem cable with router?

  I plan to upgrade my modem cable to take advantage of the increased speed that Comcast now offers in our region. I think my Airport Extreme of 2007 could be a brake on the increase in the speed of a new modem. I would like to know if it is better to buy a new modem cable with built-in wifi router.

  My current Airport Extreme supports two iMacs (24 "in 2007 and a 27 '' 2010), two iPhones and iPad two minis. My current cable modem offers 34 mb/s download speeds and download about 6 MB/s.

  I will be grateful for any advice... Thank you

  I think my Airport Extreme of 2007 could be a brake on the increase in the speed of a new modem.

  There are 2 different versions of AirPort Extreme offered in 2007... a 1st generation version and the 2nd generation.

  The 1st generation version will manage an Internet connection speed of up to about 100 Mbps. The 2nd generation version will manage up to 350-400 Mbps.

  If your new service provider will be 100 Mbit/s or lower, it is not really important what version you have. Either the version of AirPort Extreme will take care of this service.

  If your new service will be 100 + Mbps, then you will have the Gen version 2nd of the airport to take advantage of the higher speeds.

  IF you have the 1st generation AirPort Extreme... And... your new service will be well above 100 Mbps... THEN... it might be a good idea to take a look at a new modem/router.

  HOWEVER... If your new service will be less than 100 Mbps... so you probably won't receive any improvement with a new modem/router and it would be wise to simply continue to use the airport until it fails.

  So an important question here might be... what version of AirPort Extreme do you have?

  Another important issue could be... your current modem will support the service high speed?

  Open the AirPort on your Mac utility and you should be able to know which version of airport you have.  If you can provide the serial number and model of your modem, we will see if we can find out what he can do.

  If you wondering if Comcast, you should know that the person you speak to will probably receive a bonus if you order a new modem or new modem/router...so you may not receive an unbiased opinion on their part.

  Finally, there are a number of users who believe that, as a general rule that you need to replace a modem or a router in about 5 years... even if it doesn't work OK. So, you might get some interesting opinions together.

• I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  original title: WiFi

  I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  I use a Huawei E585. I simply want to clamp it alll in the tray.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• How can I connect my Photosmart HP 5510 with my cursor Asus got Tablet?

  How can I connect my Photosmart HP 5510 with my cursor Asus got Tablet?

  The Tablet uses Android 3.2 and I downloaded HP ePrint home & Biz. Also had a pincode and used it.

  The Tablet still shows "printer not found." I have to do something on the printer?

  The printer is connected to a wireless router?  What router?  You've restarted the router?

  You have enabled Web Services from the front of the printer?

• HP Envy m6-1350sf: laptop HP ceased to connect to a wi - fi connection, but it can still connect to the Internet through an Ethernet cable

  My HP Envy laptop does not connect to my home WiFi (Verizon FIOS modem). Some info:

  I had the PC for a few years and it is connected without a problem until a few days ago.

  If I plug an Ethernet cable into the PC, it connects to the Internet.

  All my other devices (computers, tablets, smart phones) to connect to my WiFi without problem.

  I got my PC in a place public wi - fi to see if she would connect. He did not.

  I have not upgraded the operating system to Windows 10.

  Suggestions?

  H @TomGinTX,

  Welcome to the HP Forums!

  It's a great place to find answers and advice!

  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums.

  Learn how to post and more

  I understand that you can not connect wirelessly to your home network or a hot spot.  Very well, you can connect with an Ethernet cable.

  Here is a link to help you solve this problem.

  HP PC - Troubleshooting wireless network and Internet (Windows 8)

  Once you have completed the steps of troubleshooting if the problem persists, please test for hardware failure.  Under the component you have network.

  HP Notebook PC - detection of hardware failures (Windows, 10, 8)

  To say thanks for the reply please click the thumb below.

  If this helped you solve the hard to please advise the posters by choosing the solution provided.

  Good luck!

• [WAG200G] problem to connect to the modem cable Alloys Atlanta Dcp2203

  Hi all!

  I recently got my new cable internet access (I used to have DSL) and I want to use my WAG200G to distribute internet by air.

  When I connect my laptop to the Dcp2203 of Atlanta Alloys via ethernet, I get an external IP (200.XXX.XXX.XXX). I need to adjust my ethernet interface get ip dynamically to achieve this.

  Now I need to connect Dcp2203-(ethernet)---> WAG200G - wifi---> portable

  How can I configure my WAG200G to work using this structure?

  Thanks to you all!

  You can't really use your WAG here. You will need a router ethernet, not a DSL router.

  The only thing you can do is use the WAG as access point and connect the laptop directly to the internet. This works as long as you don't want to connect a device to the internet at any time. You will not be able to connect 2 or more at the same time, because your ISP only allows you to have an active connection at any time.

  To set this up, you will need to connect a computer to the WAG. Open the web interface of the WAG to http://192.168.1.1/ to first set up your wireless network (SSID, enable WPA2 Personal Security with AES encryption and a password strong change). Disable the DHCP server on the main settings page.

  Then one of the ethernet wire ports of the WAG in your modem cable. Now you can connect wireless to the WAG and the WAG access to the internet and the modem. New: your computer will have direct access to the internet and will have a public IP address. You can't have two active connections at the same time.

  If you need to make changes on the WAG, you set a static IP address on your computer, for example 192.168.1.2 with subnet mask 255.255.255.0. Then you can access the web at http://192.168.1.1/ interface when you have completed your changes, go back to the DHCP/Auto IP on your computer.

  Otherwise, you should get a router, for example Wireless Linksys WRT routers.

• Problem with TC loss of connection to the modem cable

  I have a TC of 2 TB which is connected to my ISP provided by cable modem. It worked fine for 3 months after the installation in December, but now all of a sudden it will lose its connection to the modem and we lose our wireless internet. We have replaced the modem cable and it does not solve the problem. I have to reset the TC 2 - 3 times a day. Nothing else has changed recently with regard to the network set up. that only changes were to specific devices that use the wifi connection, and this was always something changing, depending on the devices we use. Any thoughts? I'm not a savvy person tech, BTW.

  We need to ask a few questions in order to learn more on what the possible cause of the problem might be.  Please be patient with this. Thank you.

  What is the number and the model of the modem you are using right now?  We ask because some modems work better than others with Apple routers, and even if you have changed the modem, it could still be a model who does not get along well with the Apple router... or... you could say that the router from Apple does not get along well with the modem.

  How old is the TC? We ask because the life expectancy, on average, a time capsule is about 3 years.  After that, they tend to start losing connections to an ever-increasing rate.

  Who is your provider of Internet (ISP) Service?  We ask because most suppliers are in the active process of implementation of a new type of connection called IPv6 in their systems... and despite ISPS claiming that their system changes should cause no difficulties connection or interruptions system... which doesn't seem to be the case at all.

  We have seen an unusual number of reports from users who suddenly have problems with their ISP connection, when things were very well for many months before. That points directly to the IPv6 changes that ISPS are doing as the culprit. In some cases, there could be way to work around the problem, and in some cases, there is nothing to do but wait as the ISP to complete their changes and be everything to speed.

• Can I plug two Airport Express units with ethernet cord and have a third Airport Express Terminal receive airplay music wirelesslly? In other words, can I combine a Wi - Fi network and roaming?

  I have an undesirable on the 1st floor, connected to the cable modem Ethernet event. I want to connect that AE to an another AE on 2nd floor with ethernet cable AND have a 3rd AE on the 1st floor to receive music through AirPlay wireless. I thought that linking the two first AEs with ethernet would improve the performance of web site on my iMac desktop, which is on the 2nd floor and connects to the 2nd floor AE via wifi. The EI the first two are newer model (MC414LL/A); the 3rd AE is old model (MB321LL/A) and is connected to a stereo Bose with a mini-jack to RCA cable double cord. I tried to set up this network using AirPort Utility, but have had no success. I don't know if it is possible to do what I want to do; and if this is the case, I don't know how to set the various parameters for each AE using AirPort Utility. I've temporarily implemented a purely wireless network; Do not connect DO NOT the two AEs with ethernet and everything works. I would enjoy my plan as above, or if I hold with purely network wireless. Any help would be greatly appreciated.

  Using ethernet network roaming between the two floors is a much better idea than anything wireless.

  The installation should be automagical if you start with the two AE plugged in by ethernet.

  It must be configured in standard roaming with identical names wireless.

  If you have any questions... Please, just after the airport utility screenshots of the configuration... but

  An express train is probably the router? You must confirm this.

  The second express is so configured in bridge... It's on the network tab, disable the bridge mode.

  

  Without thread is set to create a wireless network and simply use the same name and the same password as the other Express.

  As it should be automagical when you WAN on the second AE plugged into the LAN on the first AE.

  Wireless and then extend to will also be installed enough well automatically even if sometimes it works better in a client that extend wireless mode.

  See the Client mode.

  AirPort Express: How to join an existing client mode - Apple Support Wi - Fi network

• Can I connect a wireless modem to my Airport Extreme base station via ethernet and then connect this Ethernet modem to my TV to pinterest?

  Hello

  I want to connect my TV to my Airport Extreme via ethernet, so I can run Netflix. Can I just the branch? Can or, if it does not reach, I use an old router as a bridge linking to the Airport via an ethernet cable and connect the router to the TV?

  Thank you

  Lisa

  I want to connect my TV to my Airport Extreme via ethernet, so I can run Netflix. Can I just the branch?

  Yes.

  Can or, if it does not reach, I use an old router as a bridge linking to the Airport via an ethernet cable and connect the router to the TV?

  Yes. It is also possible, but only by using an Ethernet switch instead of a router would be a better solution. The important thing is the total distance of Ethernet between the extreme and the TV. Ethernet is limited to 100 m (328 ft)

• connect older apple Airport express with ethernet cable modem? Verizon service

  I'm helping someone with a verizon DSL modem older (guess this isn't wireless vs) which connects to a tower of Windows, then usb out of the tower to a unit of wireless to connect to a recent Mac laptop version. We would like to get rid of the tower and the verizon usb "hockey puck" and simply use the modwm > wireless Airport express > laptop.

  If I get an airport express, I can show the modem directly to Airport express?

  Yes, that should be fine.

  Tell us what model is the DSL modem.

  There are two possible configurations.

  Either the type pure or bridged modem and you use customer PPPOE over the WAN to the Express.

  Or

  You have a modem router and you will implement the express bridge, with creation of a wireless network.

  HOWEVER... I'm NOT either of those without call verizon and control on the price of a new wireless adsl router modem.

  ADSL has changed little in 10 years... but the equipment does not last forever. It could just be the perfect time to move.

• can you connect 3g usb modem to the computer than to wireless

  IM using a dell Inspiron 1525, who says: it has a wireless card, but I want to use my USB 3g internet to connect to the ps3

  Hi Richard,

  You can read the following article and see if it helps.

  Using ICS (Internet Connection Sharing)

  However, this will not work wireless. It requires a wired connection between the laptop and the game console.

  Hope this information is useful.

• How can I connect directly to a cable HP LaserJet 8150n using a Cat5 Ethernet? (It can be done)

  I use my printer in this way for months, but accidentally deleted the device in the Panel of the unit. Now, I can no longer connect or print anything. Initially, it was created by a friend who assigned its own IP address printer. But I have no idea how or what command prompts I need to enter to make the connection. If someone is good to give directions to the 'how', I would be probably happy.

  This isn't a solution, but I'll mark to close the debate. A consumer who just wants to use her HP printer, you can see how I might be confused about which thread where my question. As a printer Tech, you might well have just provided the answer rather than make me jump through hoops. As a HP representative, indicating the consumer, they are wrong and have asked the wrong question at the wrong place is not the best relations with the customer. If you do not know the answer because of the printer class, simply provide the necessary information with an apology for the confusion. Never heard of "the customer is always right" slogan?

• Connecting to a modem cable

  I replaced my old router with a new WRT310N. We have just two laptops running, there is a wired computer.

  When I set up the new router the same way and can't go, am I missing something?

  Tried cloning the MAC address of the old router to the new?