I need a way to test the computer Power Supply

Similar Questions

• need the simple way to set the computer back to factory settings, and already saved safe data

  need the simple way to set the computer back to factory settings, and already saved safe data

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner

• Is there a way to save the computer that was given to me?

  I have received a computer with no startup disk and need to save it. The computer is a Dell with MS Windows XP Home Edition 2002. Is it possible to register the computer?

  jac516,
  When you say that you need to the "Save" what exactly are you meaning?  You get a popup window indicating that you need to do something?  If the PC was set factory default before being returned to you, then you will need to activate your copy of Windows.  If this is the case, then you can click on start > all programs > Accessories > system tools > activate Windows.

  If you are prompted for a different record type, then you will need to contact Dell. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• ProBook 4530 s BIOS update fails - "...". the computer is not connected to the external power supply. »

  I made an update of the system to the original settings and everything seems to go as usual.  While performiong the many windows updates, I noticed that the battery indicator indicates "no battery installed.  I found a few solutions dealing with this problem (none of the other solutions worked) and that which is shown updating BIOS.  I checked and the BIOS is F.07 and the current version is F.41.  I downloaded the update and begun the process of Windows.  The system restarts to start the process, but when the BIOS updated starts I get the following message:

  "A significant update of the BIOS of the system is available, but the computer is not connected to the external power supply.  Please connect the external power supply and then press Enter to continue. »

  The computer is connected to the power of HP to the original address since it is the only way so he can turn it on.  I tried removing the battery and from the update only the connected power and get the same result.

  Either way, I tried to insert a different battery, I have more than one of these laptops.

  Sorry

  Please test the battery after boot press F2 HP Diagnostics

  http://support.HP.com/us-en/document/c00821429

  and calibration of the battery for laptop

  http://support.HP.com/us-en/document/c00817650

• HP Pavilion p6-2: problems on blocking down after I installed the new power supply on a p6-2207ep

  Hi all

  B4 explaining my problem, I really don't know if I should post this in office, or material in this section of the freezes/crashes/locks but since I posted in freezing section and no results I decided to try here.

  My pc: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03382032

  I bought a new PSU: XFX TS 550W 80PLUS BRONZE for the GPU upgrade 380 R9 I was planning to do.

  Is there some BIOS I get HP for this cause of power supply from what I read, if I not only one of the things like manufacturer reset to the factory settings may stop working... Currently, my Bios version is 7.11...

  Problems with the new power supply:

  When I closed windows 7, the first problem, the picture freezes on the screen that says "blocking windows down", I waited a bit and nothing, tried to turn off the machine while keeping down the power button but nothing to disable directly in the rear switch of the PSU...

  Second time happened a little different soomething, seconds after freezing again on the screen that says "blocking windows down" windows actually turned off and the screen is off but everything inside the computer case continues to flow fans in light of the power button / stop and was also able to close by keeping pressed power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  Also tried the GPU with the new PSU fans worked but no entry in the screen that I guess just a power supply problem.

  ATM, I'm RMA waiting to know if it is a power supply defective or not...

  Problems after the reinstallation of the original material:

  Some of the same problems when I got the new PSU remained namely:

  Windows actually stop and the screen is off, but everything inside the computer case continues to flow fans in the light of the button on / off and was also able to close by keeping the power button...

  When I restart the computer, to which some time stops, and only after a few seconds, it turns...

  What I've done so far to try to fix the problem:

  Restore windows 7 to a b4 point the hardware installation.

  Reset the BIOS

  Hard reset

  Clean boot

  Do you have a full checkdisk which means 0 KB in bad sectors...

  A complete hardware checked all tests with the HP software

  A system file check everything beautiful

  What I fear most is a faulty PSU that may have caused damage to my equipment mainly the motherboard, but could be something else entirely.

  Maybe I need a specific BIOS for that motherboard / PSU combo, but after returning to the source material, the problems remained.

  What I can do because I can only make the software tests since I don't have an extra PC to test the parts...

  Hello

  Disconnect all external devices except the keyboard and mouse when you try to solve the problem.

  Disconnect the PC and removed the CMOS battery.  Press and hold the power for 30 seconds.  Now, replace the CMOS battery and plug the PC give a TI a go.

  Your PC is not stable enough to make a BIOS update. Do not attempt to use the graphics card XFX until your PC is stable enough to make a BIOS update.

• Can power supply Question - I use the 230W power supply with a W540?

  I have a W540, which currently uses a power 170W (8.5 a 20V)

  I got also a docking station for a P50 that has a power of 230W showing 20V 11. 5a.

  The connectors are similar, but I'm hesitant to try the 230W power supply in the W540.

  It is allowed to use the 230W power supply with the W540?

  230 watts is maximum power feeding, it only provides the energy required by the computer.

  I sold my W540, so I can't test it for you. But I do use the ThinkPad X 1 carbon with 230 watts without no problem power adapter.

• The 460W power supply will be sufficient for the GTX 1070?

  Just place an order for a R5 with an i7, GTX 1070 and a diet of 460W.

  I'm not going for the largest power supply, because I'm not a fan and do not upgrade components.  If the configuration of Dell said 460 page might work, I saw that he needed to upgrade the PSU. I preferred using the extra $100 for the video card rather than the 970-1070.

  Now, reading around forums, I continue to see comments that the recommended food for a GTX 1070 is 600 Watts (by guru3d.com).

  I still have time to cancel the order because it is very recent.  Do I need to worry about this power supply?  How would I know if it is not sufficient for use?  The frame rate would be low, or the stability of the system would show signs?

  Hello

  Yes, the 460W will work well if is unique. Check the image below and let me know if you need anything else:

  

• Dimension 4600 doesn't work with the new power supply

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Hi all

  I replaced the power supply in my 4600 today so he would welcome a Nvidia Geforce 7950GT AGP.

  The model is an integrator of Aerocool 500W 80 Plus Bronze. http://www.Amazon.co.UK/GP/product/B00JKVHKSU?

  The 4600 has two sockets on the motherboard. A 20 pin and 4 pin. The new power supply had a 24pin cable that I shared, so it became 20 + 4.

  It is not working properly. With all the connected cables (2 cables for the mobo) and 2 connectors molex to drive HARD and CD - R, there is a flashing orange light on the front of the computer and a green light on the motherboard. Some discs don't look, no noise. Nothing is on. If I remove the power cable from motherboard 4 pin POWER supply lights up and the fan from the CPU. There is no problem when I connect the old Dell 250w PSU back up.

  Some of the reviews on Amazon have said that some cable has been connected to wrong and only he re-wiring to work. I don't know if this applies to me? I took some pictures of the connectors. http://imgur.com/a/6m9pu

  Someone at - it ideas?

  Thank you

  Andrew

  AV115

  Have you used the connector 4 pins, which was part of the 20 + 4 P1 12v connector, connect to the P2 4 motherboard connector pins 12v?

  
  See 41, J5B1 Connector [aka P2]

  http://FTP.Dell.com/manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-4600_service%20manual_en-us.PDF

  
   http://www.AOne.co.UK/prodinfo.asp?ProductID=4523

  Connector 4 + 4 pin 12v PSU is divided into two 4-pin connectors and one of them, can be used for the P2 motherboard connector.

  Bev.

• CPU limitation with the new power supply

  Hello

  I have a W510 with 135W POWER supply. Or to be more precise: A 6.75 @ 20V.

  I work at two locations, so I bought a generic 150W PSU with an adapter to mount the Thinkpad. The PSU is labeled 7. 5A @ 20V, so there should be no problems running the laptop.

  Yet, when starting, I get the "this power supply is too low for something something something battery charge" and strangled my i7 at 1.2 GHz, and not the 3.06 there are usually.

  If I boot from the battery and connect the connector of the power supply after Windows is in place, it works at full speed. And to charge the battery very well. Then of course, there is nothing wrong with the juice from the PSU.

  Thus, I suspect that the BIOS does something stupid. Can I override this somehow?

  Friendly,.

  A guy

  Maybe what the ThinkPad does not does not correctly detect the generic adapter. The central axis of the generic adapter does not give the right signal to the laptop power management firmware.

  Check in the ThinkVantage power manager what to say under the generic adapter 150 watts? He said 90 watts?

• "Generic Host Process for Win32 Services has encountered a problem and needs to close" to start the computer.

  Original title: Generic Host Process for Win32

  A few days earlier, when I restarted my computer, I got an error message indicating that there was an error in the Generic Host Process for win32 and we had to close the program. The only thing it really seems to have an impact on the time is my speakers. I'm not all sounds to play, but when I turn my computer off, he will play the melody of the judgment.

  I tried to fix this problem without success. I tried to install the windowsXP-KB894391 package - x86ENU.exe as indicated on the website. However, when I try to install it, I get a message indicating
  "Setup has detected that the version of Service Pack for this system is newer than the update you are applying.
  There is no need to install this update. »
  Any thoughts?

  Hello Courtney0210,

  Thank you for the question!

  I'm sorry to know that have problems you with startup error. As I understand it, you get an error to the error of starting in the Generic Host Process for win32 and that the program had to close.

  I need to ask you a question to help you best.

  Were there any changes (hardware or software) to the computer before the show?

  Perform the steps in the link and check.

  Error messages when you start a Windows XP-based computer and then try to download Windows updates  

  Answer to us if you are having problems with error starting or any other issue of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• Best way to test the GPS applications

  Hello everyone. I develop a GPS application and need some advice on tests. It works on the sim card and a device, but it runs in the background and after some time of inactivity not to move, that the GPS seems to fall asleep, he ceases to update. I can only produce this by circulating for a while, then stop and start driving again. This is not practical if anyone can give some tips on testing and debugging of the GPS apps?

  Your app throws an exception?

  You can also use the EventLogger to log messages

  EventLogger.register ( myappguid , "myapp", EventLogger.VIEWER_STRING);
  EventLogger.logEvent ( myappguid , mymsg, EventLogger.ALWAYS_LOG);

  and ALT-LGLG to view then on your phone.  Place a large number of newspapers msgs help for debugging on a real device.

• How can I disable the password so I don't have a need every time I start the computer? I am running VISTA

  I just want to turn on the computer and not necessary to use a password. I am running VISTA on a ACER aspire 9410-2028

  Hello

  This should help you:

  "How to Log on automatically on startup of Vista '

  http://www.Vistax64.com/tutorials/66966-logon-automatically.html

  See you soon.

• Good way to recharge the computer to increase autonomy

  Dear support Member,

  I use a HP-Envy-Spectra-14-3010NR model that runs on Lithium-Ion battery.

  I'm not very sure about what is the best way to increase the life of my battery systems. In previous models, I have suggested to me that I must leave my battery discharge completely at least once a week and then reload.

  What is the mode of operation in suggested Lithium-Ion batteries?

  Should I still keep running on the load (with power on) or should I let it load completely, then turn off the sector until the battery is completely empty - or there is another way that is more suitable.

  Please suggest.

  Thank you.

  Hi NMahajanCA,

  It is not necessary to do the foregoing. Drain the battery or charge not completely will increase or decrease the battery life. Here is a link to understand your battery.

  http://support.HP.com/us-en/document/c00596784

  Calibrate the battery resets the battery indicator to accurately display the charge level in Windows. Here is a document on how to do it.

  http://support.HP.com/us-en/document/c00821536

  I hope this helps.

  Thank you.

• Fried computer due to the bad power supply

  We did not have the computer turn on the correct voltage (it was about 120 instead of 220).

  What are the possible problems we will encounter?  Yes, the computer does NOT work.

  And what options do we solve the problem?

  It was a gaffe. I changed the switch, then my husband - lack of communication. It's a new computer desk-never used - Yes a Christmas gift for my son.

  And what is the best place to try and get a new power supply?

  Since it is a forum in the world...  The best place to get a power supply depends on where you are.

  How to determine what to...?

  Well, if this is a new machine, those you purchase contact and see if they have one, they will do out trade / sale you that will work in your machine model.  In this way, you KNOW you are getting the right feed...

  Otherwise, you will need to either take the power on (noting where everything happens so you can put a new) and take it to a shop selling things to get a replacement (large stores area, a small computer specialty store, etc.) or you will have to take the system with you and let the store that you buy to do it for you.

• I configured the netgear wireless router and works fine but when I turn the computer power off and back on I can't get connection

  Hi can anyone help, I am with AOL, I just switched to the Platinum service, I configured my router netgear DG834G wireless and that's all works fine, but if I turn the computer then turn it back I cannot get a connection and when I ask her to fiind wireless networks the computer tells me that windows does not support my wireless network and I must have another program running , but I didn't so I have to reload the settings again for windows to set it up. What happens whenever I turn off the computer. AOL are without help please someone has any ideas - I use windows xp service pack 3

  Hi Timstimpson,

  It is possible that the Automatic Configuration Windows wireless service is not configured to run at startup.
  Try the following:
  1. click on Start and run
  2. type in the box to run services.msc
  3 scroll down and look for the Automatic Wireless Configuration service
  4. double-click on the service and make sure that the Startup Type is set to Automatic
  
  
  Let me know if it works for you!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.