IMAQ video on the display mode - resolution wide screen

Similar Questions

• Interactive reports: how to change the display mode (details, group by, chart, pivot) programmatically?

  Hi guys,.

  is it possible to control the display mode of the interactive reports, i.e. display icon, list, view detail, group by, chart, pivot?

  

  As I understand the current setting is stored as a preference of the user for each user... and again when his connection. A settings of the rules them all (all the stored report parameters).
  
  The display mode switchable using a javascript, the api package apex_ir or via a link?
  
  Thank you
  ~ Dietmar.
  

  Hi Dietmar,

  It is not a supported way to change the display interactive report mode.  With the device connected by Anthony internally, we will consider adding this because part of apex_ir or a link to the future.

  Kind regards

  Christina

• Problems with the Display Mode target on end 2009 27 "iMac

  Used late 2009 iMac 27 "in the view target in conjunction with a Dell XPS tower with i7 processor, Windows 7 and the best graphics card I could afford at the time connected by HDMI to mini display port cable.  Worked well for years.  Set aside Dell for a few months and the update of the iMac to El Capitan OS 10.11.3.  Recently tried old setup with same Dell PC and was able to move from Mac to PC, but the PC screen resolution was at the lowest setting. I got an error message when enabling/disabling to PC who said there was a problem with the port causing mini display of the system back to the lowest resolution. Impossible to reset at a higher resolution.

  I tested the Dell PC on another monitor, and it works very well at higher resolution (2560 X 1440). Now, when I reconnected it to the iMac (which works fine), the screen becomes black.

  Is it possible that the operating system upgraded (El Capitan) is not compatible with the targets using mini display port Display Mode?  Any ideas?

  Use your iMac as a display with the target - Apple Support Display Mode , also consider having a bad cable or connection. Does not hurt to try different cables, they can and will the bad!

• How to activate the resolution wide screen to external monitor on Equium A60?

  Hello

  I had an Equium A60 with an ATI Radion 7000 mobility grahpics chip in it. Earlier the LCD is dead and has decided to use an external monitor rather than replace it. However, the external monitor is a monitor 22 '' widescreen computer does not provide a display suitable for resolution. Is it possible to update the graphics driver to provide the wide screen formats. I looked on the toshiba updates, but there is nothing new there, and ATI are not ready to support offer it on a laptop.

  Any ideas?

  Hello

  You can't choose your preferred resolution because the graphics driver does not support.
  Eventually the 3rd party driver support your favorite display resolution, but to be honest I wouldn't use these drivers because it could cause serious difficulties for laptop.
  The point is that these 3 third-party drivers are untested and not certified by Toshiba.
  Therefore, the use is at your own risk.

  Good bye

• Flashing black rectangles on the normal display mode (not full screen)

  In the last two weeks, I downloaded the latest version of Firefox. Now when I open a browser, black flashing boxes appear whenever my cursor moves and the screen is unusable because of this. The only solution I have found so far is to use the mode setting full-screen. Then, the screen is stable and the black boxes are not anywhere on the page. Anyone has a suggestion on how to fix flashing black boxes?

  Please see images added to this posted question. Thank you!!!

• Cannot set resolution wide screen on Satellite A100

  I have a Hanns G HG216D 22 "(visible de 21,6")) LCD display external, who hails from WSXGA (1680 x 1050) and is horrible to other resolutions. "
  I can't select the correct resolution in XP or Vista (I know, because having failed I restored (clean install of authentic Pro with SP2 disc) XP then failed on XP used a Vista Business Upgrade disc to try Vista.)
  But nothing helps: (.)

  The laptop is a Toshiba A100 PSAA8 with a graphics processor Intel 945 G Chipset.

  Here's what I've tried:

  There is a driver on the disk of the specifically labeled monitor as for Vista 32-bit, so I used the disc have... 'trick' via Device Manager to force Vista to use this INF file, I tried adding EDID (or was - this CSD, something like that) data to the pilot (after driving backward before re - apply incase she thought it was the same driver), I tried PowerStrip, although I'm not familiar with it, 99% some it work well (, one of the first things I tried was using the specially created driver for this chipset that is designed to solve this problem very issue (http://www.Intel.com/support/Graphics/SB/CS-028366.htm)), any ideas?

  The LCD has DDC2 and activated but EnTech MonInfo cannot get any data from it. I think I should go back to Linux; never had a technical problem I can't solve there (only DRM related issues, etc.), only problem I use this machine for work and don't mind using virtualization for some things but not for "critical to pay my rent" stuff!

  I don't have another machine to test the screen either, as my sister lost with my laptop alternative.

  Any help would be greatly appreciated :).

  Hey Buddy,

  Then I read a little in some forums on your question. The first question is: have you updated your BIOS? It's really important because many users in the forums Ubuntu has reported that, after that an updated bios updated widescreen stuff work. Since the you´re works with Vista, I would say firstly you update your BIOS, remove all drivers display with 'Driver Cleaner Pro' and then try the drivers from the website of intel again (as an especially for this wide screen problem)

  Maybe it works, I confused why it doesn't since this chipset is designed to pull many of the higher resolutions and even all res widescreen 1680 x 1050 and 1440 x 900.

  Just give a short answer on your situation. :)

  Welcome them

  P.S.: If you try with linux check this thread on the ubuntu forums:
  http://UbuntuForums.org/archive/index.php/t-454805.html

• Port Replicator Slim 2 - resolution wide screen

  Hello

  Consider buying a Slim Port Replicator 2 for my Portege R500.
  I have two questions about the Replicator:

  The maximum specified. resolution is 1600 x 1200. I want to connect a monitor with a resolution of 1680 x 1050. Will this work?

  I'm using linux and I'm worried if there is some kind of windows driver only required to operate the Replicator?

  Hello

  I m not port replicator expert but to my knowledge the Slim Port Replicator 2 supports 1 x RGB (monitor), 1 x DVI port (video) that allows a resolution of 1600 x 1200 max.

  As mentioned the DVI port supports 1600x1200px max and other higher resolution is not possible.
  But maybe you'll be able to choose your favorite of the 1680 x 1050 resolution using RGB (monitor) port

  Best regards

• Color calibrator may not work correctly, because the display does not fill screen.

  I have a Thinkpad W520 with 1920 x 1080 HD display and the color sensor. I tried to run the color standard application but always, she will work until the end but cannot process measures. So I opened the lid in the middle of a calibration and discovered that the color screen that is supposed to be seen by the sensor is not full screen, thus preventing the color measurement sensor. How can I set the graphics so that this application is displayed full-screen when executing? Thank you.

  Yes. But I just solved the problem. I set my display to display the text, icons, etc., to 150% of normal resolution. Somehow, he was causing the application displays only a partial screen. I set the magnification to 125% and now the standard color works very well.

• How to change the display mode screen landscape

  original title: screen display

  my 1 year old has done something to my computer and now when I start it up to the top of the screen is in landscape mode.

  All versions: hold down Ctrl & Alt keys and use the arrows to rotate backwards.
   
  Vista: right-click on the desktop | Graphics options | Rotation.
  Windows 7: right click on the desktop | Screen resolution | Orientation.

• Image not appearing is not in the Display Mode

  I've just upgrade to DW8 2004 DW. After you start DW8, I realize the images on my Web pages are not displayed in the Mode display of DW8 but I can still see the images in 2004 DW. All settings are correctly presented DW2004 DW8, but the images are still show as General images rather than real pictures.
  
  Are there settings I'm missing?
  
  Here is an example of my code from the image.
  "< img src="/eSCM/Images/Buttons/Submit.gif "alt ="Submit"width ="55"height ="20"onClick ="Submit (); ">
  
  

  I found the solution. When you change the site on a remote server as in my case, you can not put \\wnas001\ecmp to the site folder. Instead, you will need to map the drive and use the map as in

  T:\

• problem in the air mode application full screen

  Hi all

  I am facing a problem in creating an air application. I used modepleinecran. FULL_SCREEN_INTERACTIVE to maximize the window when loading the application has been successful to some extent. But there is only one bar at the bottom a problem happens right under the window. can someone help me please. I enclose with this preview.

  Thanks and greetings

  I need the code of the project to check because lack me the images.xml file and the file descriptor-app.

  In the file descriptor to be sure of the value none systemChrome and transparent for real.

  Then in your WindowedApplication tag, after the backgroundImage, for example, add ShowStatusBar is stored = "false". That should fix your problem of background-space.

• In case of failure of the computer virtual to define the topology of the display after a period of inactivity

  Hello, we are facing a problem with a small subset of our VM here full clones, Windows 7 workstations. We are connecting via Wyse P25 zero with firmware 4.1.2 customers. From time to time (not always, not always) the virtual machine will give a black screen after the user returns for time away from their office. When this happens, we see data such as the following in the PCoIP server log.

  15/10/2013, 13:26:19.827 > LVL:0 RC: 0 SERVER: == > WindowProc: event detected WM_DISPLAYCHANGE (1920 x 1200)

  15/10/2013, 13:26:21.576 > LVL:1 RC :-500 IMG_FRONTEND: set_display_topology: VMwareResolutionSet_SetDisplayTopology failed (result of topology = 0).

  15/10/2013, 13:26:21.578 > RC LVL:2: 0 IMG_FRONTEND: display device [0]: \\.\DISPLAY1 (VMware SVGA 3D)

  15/10/2013, 13:26:21.578 > RC LVL:2: 0 IMG_FRONTEND: display device [0]: States - DISPLAY_DEVICE_ATTACHED_TO_DESKTOP DISPLAY_DEVICE_ACTIVE DISPLAY_DEVICE_PRIMARY_DEVICE

  15/10/2013, 13:26:21.580 > RC LVL:2: 0 IMG_FRONTEND: display device [1]: \\.\DISPLAY2 (VMware SVGA 3D)

  15/10/2013, 13:26:21.580 > RC LVL:2: 0 IMG_FRONTEND: display device [1]: States - DISPLAY_DEVICE_ATTACHED_TO_DESKTOP DISPLAY_DEVICE_ACTIVE

  15/10/2013, 13:26:21.582 > RC LVL:2: 0 IMG_FRONTEND: display device [2]: \\.\DISPLAYV1 (JSDLP chained DD)

  15/10/2013, 13:26:21.582 > RC LVL:2: 0 IMG_FRONTEND: display device [2]: States - DISPLAY_DEVICE_MIRRORING_DRIVER

  15/10/2013, 13:26:21.584 > RC LVL:2: 0 IMG_FRONTEND: display device [3]: \\.\DISPLAYV2 (RDP Encoder Mirror Driver)

  15/10/2013, 13:26:21.585 > RC LVL:2: 0 IMG_FRONTEND: display device [3]: States - DISPLAY_DEVICE_MIRRORING_DRIVER

  15/10/2013, 13:26:21.586 > RC LVL:2: 0 IMG_FRONTEND: display device [4]: \\.\DISPLAYV3 (RDP reflector Display Driver)

  15/10/2013, 13:26:21.586 > RC LVL:2: 0 IMG_FRONTEND: display device [4]: States - DISPLAY_DEVICE_MIRRORING_DRIVER

  15/10/2013, 13:26:21.591 > LVL:2 RC :-500 IMG_FRONTEND: process_display_topology: Failed - 2 requested screens, 4 remaining trials.

  15/10/2013, 13:26:21.591 > LVL:0 RC: IMG_FRONTEND 3: open_displays(): display processed topology request: failed.

  15/10/2013, 13:26:21.946 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:21.946 > LVL:0 RC: IMG_FRONTEND 0: configure_displays: 4 views presented initially!

  15/10/2013, 13:26:21.946 > LVL:0 RC :-500 IMG_FRONTEND: configure_displays: warning - poster overlap: [LRTB]: [1920,3839, 0.1199] X [1920,3839, 0.1199]

  15/10/2013, 13:26:21.948 > LVL:0 RC: 0 SERVER: == > WindowProc: event detected WM_DISPLAYCHANGE (1920 x 1200)

  15/10/2013, 13:26:21.954 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:21.954 > LVL:0 RC :-500 IMG_FRONTEND: open_displays(): can't set screens, devtap reset.

  15/10/2013, 13:26:21.963 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:21.963 > RC LVL:3: 0 IMG_FRONTEND: reset_devtap: SVGADevTap reset

  15/10/2013, 13:26:21.963 > LVL:0 RC: MGMT_IMG-500: cSW_HOST_IPC::enable_frontend failed. 10 remaining attempts. Try again...

  15/10/2013, 13:26:21.963 > LVL:0 RC: 0 SERVER: == > WindowProc: event detected WM_DISPLAYCHANGE (1920 x 1200)

  15/10/2013, 13:26:21.976 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:21.981 > LVL:2 RC: 0 SERVER: Desktop power: EVENT_SYSTEM_DESKTOPSWITCH

  15/10/2013, 13:26:22.963 > LVL:0 RC: 0 IMG_FRONTEND: Calling open the display mode Tera2.

  15/10/2013, 13:26:23.562 > LVL:0 RC: 0 SERVER: == > WindowProc: event detected WM_DISPLAYCHANGE (1920 x 1200)

  15/10/2013, 13:26:23.881 > RC LVL:1: 0 IMG_FRONTEND: set_display_topology: VMwareResolutionSet_SetDisplayTopology succeeded (topology result = 1).

  15/10/2013, 13:26:23.881 > LVL:0 RC: 1 IMG_FRONTEND: open_displays(): display processed application topology: with success.

  15/10/2013, 13:26:23.884 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:23.884 > LVL:0 RC: IMG_FRONTEND 0: configure_displays: 4 views presented initially!

  15/10/2013, 13:26:23.884 > LVL:0 RC :-500 IMG_FRONTEND: configure_displays: warning - poster overlap: [LRTB]: [1920,3839, 0.1199] X [1920,3839, 0.1199]

  15/10/2013, 13:26:23.885 > LVL:0 RC: 0 SERVER: == > WindowProc: event detected WM_DISPLAYCHANGE (1920 x 1200)

  15/10/2013, 13:26:23.887 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:23.887 > LVL:0 RC :-500 IMG_FRONTEND: open_displays(): can't set screens, devtap reset.

  15/10/2013, 13:26:23.891 > LVL:0 RC: IMG_FRONTEND 0: resync_windows_topology: new api called successfully

  15/10/2013, 13:26:23.891 > RC LVL:3: 0 IMG_FRONTEND: reset_devtap: SVGADevTap reset

  15/10/2013, 13:26:23.891 > LVL:0 RC: MGMT_IMG-500: cSW_HOST_IPC::enable_frontend failed. 9 remaining attempts. Try again...

  15/10/2013, 13:26:24.891 > LVL:0 RC: 0 IMG_FRONTEND: Calling open the display mode Tera2.

  15/10/2013, 13:26:24.954 > LVL:0 RC: IMG_FRONTEND 0: configure_displays: 4 views presented initially!

  15/10/2013, 13:26:24.954 > LVL:0 RC :-500 IMG_FRONTEND: configure_displays: warning - poster overlap: [LRTB]: [1920,3839, 0.1199] X [1920,3839, 0.1199]

  and so on...

  On end-user behavior, is that they get a black screen, followed by a gap. View Connection Manager console reports as "connected". We have to reset their virtual machine or restart from vSphere in order to get them reconnected. We found a VMware KB here which indicated that it was a result of the computer, put the display to sleep (in power politics), so we put in place a group policy to configure this 'never' (said also the problem was resolved after view 5.0, while we are running 5.2). Issue still occurred. Recently, Teradici support (we have a case open with them as well as with VMware) suggested that disable us the accelerator of Shoretel desktop sharing, so we tried it. Problem occurred again today.

  So, no matter who in the community never encountered this and could you remedy this? Our users are extremely frustrated.

  We believe that we have solved this problem. It was related to client connections on the zero P25 and who monitor they were trendy. So if a user has his left monitor the value primary (as per normal), but the port number a display on the zero client goes to the right screen, then the 'primary' switching must occur in the software somewhere along the way. This leads to the poster of overlapping and sometimes, not every time the VM would fail to fix and would be left in a State where we had to reset it from the vSphere client. As we exchanged the range of cables to make sure that zero client a monitor port is connected to the main screen of users, this issue appeared (two weeks and counting, fingers...). We have a few users who prefer the right monitor being their main, so we put the cables in front of them.

• In After Effects when I use the Color Finesse 3, a grid appears in the display. How to disable that?

  When I click the button, and then synthesis, then ITS Color Finesse 3 creative cloud, a grid appears on the video in the display window, and I don't know a how to take that off?

  Color THE 3 Finesse provided with After Effects and is automatically installed during the After Effects is installed. The only reason to upgrade to the paid version if you want to use Color Finesse in Premiere Pro, as well as in After Effects.

  Because this is a college computer, you have the option to install/uninstall software? Many universities to lock down computers in order to limit this access. You will need full access including an admin password, to use the following steps. If you are not allowed access, you can pass the following to whoever does the computer management.

  To remove the trial version, delete the entire folder "Synthetic aperture" found in:

  / Library/Application Support/Adobe/Common/Plug-ins/7.0/MediaCore

  (Note that it is the library folder at the base of your boot drive, not that of your home folder).

  Then, re-enable the embedded Color Finesse version by going to the following folder:

  / Applications/Adobe/Adobe After Effects CC/Support Files/Plug-ins/effects/Synthetic Aperture

  Now, in this "Synthetic aperture" folder, you will find a plug-in with parentheses around the name:

  (Color Finesse 3 AE64)

  Remove the parentheses by the name of file for AE go to him. Not NOT remove parentheses from the folder "(Support CF3)" or AE will launch very, very slowly, and Color Finesse is not working properly. "

  "Finally, in the"(Support CF3) folder ", find it" (Color Finesse 3 IU) "application and remove the brackets.

  Launch of EI, apply Color Finesse to a layer, enter a name, and you should be good to go without grid lines.

  Bob Currier

  Synthesis

• Apex 4.2.1: Bug icon display mode

  Minor but very annoying bug in point 4.2.1. Application App Builder (4000: 1) home page has a link in the right sidebar to select the Display Mode (icon or text) for 5 large buttons at the top (to run App, supporting objects, shared components, utilities, and Import/Export).
  
  I prefer the hide icons setting and is registered as a preference by user and the default icons , so one might expect that once I put it to hide the icons who's who.
  
  But the links Page change nn and nn to the app in the toolbar of developer in a rendered page are like f? p = 4000:4150:953853045141:NO: * 1 *, 4150... Then they clear the cache of the page 1 and it resets the display of default icon :-(
  
  Could it if you please be repaired? I love the work and the quality of the icons, but I really don't want it taking up so much screen real estate.
  
  Thank you
  
  Published by: Elizabeth on 9 January 2013 14:56

  Hi Vikas,

  I have the problem as bug # 16095793.

  Are BTW, you sure that the value is normally saved as a user preference? Because I did a quick test, changed to hide the icons, disconnected and then connected again and the manufacturer showed more icons. Couldn't find it in the code that the value is stored as a preference.

  Concerning
  Patrick
  -----------
  My Blog: http://www.inside-oracle-apex.com
  APEX Plug-Ins: http://apex.oracle.com/plugins
  Twitter: http://www.twitter.com/patrickwolf

• Programmatically set the display type of IR

  The last post in this thread asked the value of the display mode of the interactive report programmatically.
  Re: How to configure the active tab (programmatically or not) of IR?
  
  I'm sure it can be done via javascript, but I'm not entirely sure how.
  
  Looks like Dimitri has made on apexblogs.info
  http://www.apexblogs.info/pls/Apex/f?p=118:tweets:0
  
  Ideally, I would like to display an IR with no search bar and provide only the detail view.
  
  ScottWe

  Hi Scott,.

  That is correct, on the Home Page and on blogs and pages of tweets, the interactive report is run by default in the Details view.
  Really simple to do this; Create dynamic Action during the loading of the Page and the real action's Javascript:
  gReport.data.view ('DETAIL');

  Hope that works for you,
  Dimitri Gielis
  http://Apex-evangelists.com
  http://dgielis.blogspot.com
  http://apexblogs.info