Implementation of IPSec Port Forwarding on a Windows 2012 with a LRT224 Server

Similar Questions

• Setting up Port Forwarding on router WRT54G, working with a WVC54GCA Wireless CAmers

  I have the equipment in question and you need to know a few things when it come to put in place for Internet access. Before I aske the question, however, I have the following IP addresses associated with this project: WVC54GCA - 192.168.2.102, router WRT54G - 192.168.2.1, the questions are:

  1. How do you define Port Forwarding on every element.
  2. Should the two articles have static IP addresses.
  3. Once the port forwarding is set, what is the structure of the URL to access the camera?

  Any help would be appreciated, summer tear my hair on it. Seems simple, but obviously not. I'm missing something.

  Thank you

  For port forwarding, you will first need to set the camera to a fixed LAN IP address (static).

  If your router uses the range of 192.168.2.100 thanks 192.168.2.149 DHCP servers, then 192.168.2.102 is an unauthorised fixed address.  With the Linksys routers, any fixed LAN IP address must be outside the range of the DHCP server.

  Here are the rules of use of the fixed LAN IP addresses with Linksys routers.  (Note: these rules were written for the 192.168.1.x subnet.)  Since you're using the 192.168.2.x subnet, change all addresses accordingly):

  With Linksys, routers, a fixed (static) IP LAN addresses must be assigned in the device that uses the address. If you need to enter the fixed address to the computer, printer or camera, not in the router.

  When you use a Linksys router, any fixed LAN IP address must be outside the DHCP server rank (typically 192.168.1.100 thru 192.168.1.149), and may not end with 0, 1 and 255.

  That's why any fixed LAN IP address would normally be of the order of
  192.168.1.2 thru 192.168.1.99 or
  192.168.1.150 thru 192.168.1.254
  assuming that you always use the default DHCP server line.

  In addition, in the computer, when you configure a static LAN IP address, you need to set the "Subnet mask" 255.255.255.0 and the 'default gateway' on 192.168.1.1 and "DNS server" to 192.168.1.1.  Note that some network devices can not use server proxy DNS at 192.168.1.1.  In this case, the value "DNS server" your real address of Internet DNS server (found in the router when connected to the Internet).

  It is also important that the same value static LAN IP address no two devices on your network.

  **********************

  After you gave your camera at a fixed LAN IP address, then go in "Port Redirection" in the router and configuring the ports one (or more) to the address LAN IP fixed camera.

  In order to access your camera from the Internet, you will need to either:

  (1) get a fixed Internet IP address (static) address from your ISP and configure your router to use this address, or

  (2) use a free service such as DDNS.  DDNS allows you to use a dynamic Internet IP address, but can connect you by using the same URL.

  I hope this helps.

• Set the name of the network on a Windows 2012 without Active Directory Server

  I have a Server Windows 2012 I use for DHCP, DNS and NAT on a network without a domain controller, and I don't want to create a domain.

  When my Windows 7 clients connect, they identify the network with the name of 'network '. Is there a setting on the server, Windows 2012, that will allow me to change the name that clients identify the network with? I want something that is on the side Server and not to go and rename it on each client manually.

  I noticed low-end devices how as access points, modems etc use their own custom network that clients identify their network with, so I guess it cannot be something too difficult...

  Thank you in advance.

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• What should be the port/security settings for Windows Mail with Vista - I think they changed?

  I had to reinstall Vista when my hard drive crashed, and Windows Mail does not work completely correctly. I think remember me an email from Microsoft told me to change the ports/security settings. Could someone tell me what they should be?

  A "error message indicating", what exactly? No error code or the relevant text?
   
  Make sure these settings match exactly.
   
  Set up Windows Mail for E-mail XFINITY/Comcast
  http://customer.Comcast.com/help-and-support/Internet/configuring-Windows-Mail-Xfinity-email
   
  
  Leave messages on the server and it clutter?
   
   

• RV220W and Port forwarding

  Hello

  I have a problem with my Cisco RV220W with Firmware 1.0.3.5

  I have in my local network a Dreambox with the IP 192.168.1.230, he listen Port 8880.

  How can I implement a WAN port forwarding to the Dreambox?

  Thank you

  Michael

  Hi Michael,

  Thank you for posting. Please follow the steps below to transfer the port to your Dreambox:

  1. Log in to the router, then go to: Firewall-> Access Control-Services > custom.
  2. Press 'Add' and then type Dreambox name, TCP for type. The Port of departure and Port of finish will be 8880. Press "Save".
  3. Go to the IPv4 firewall rules and press 'Add '. Use the following settings:

  Area: No reliable (WAN)

  Area: Trust (LAN)

  Service: Dreambox

  Action: Always allow the

  Source host: no

  Send to the Local (DNAT IP) server: type the address LAN IP of the Dreambox here device (i.e. 192.168.1.150)

  Ignore the other settings on this page and press 'Save' at the bottom. You should now be able to reach the Dreambox from the Web using: 8880

  Please let us know if it works or if you need further assistance.

• Port forwarding blocking access SSH, POP3, and IMPA

  I recently acquired a Linksys EA8500 and very strange, annoying, and annoying problem has developed. I have a mail server and files in my home network I can access it from outside my house using a dynamic IP service. The server is running DNS as well, so it can be but from inside and outside the local network form using the same URL. Of course, external access, to set up the port forwarding on the router. This Setup has worked well with my previous, lower end, (a D-Link) router and, for a while, with the EA8500. However, there are some time (and I'm not aware of anything that has changed the situation) it doesn't work anymore: If port forwarding is enabled, requests for access over WiFi within the local network and outside the LAN are received by the server, as if they came from the top , instead of the actual computer and are thus rejected (authetication is through security keys). Always access requests work correctly on the cable connections and return to normal over WiFi if port forwarding is removed. Of course, this cancels the whole point of port forwarding. This never happened with the router D-Link and, as I mentioned, didn't happen with the EA8500 first. I have enabled and then disabled access as a guest and no DMZ have put in place, but which did not help. I have both the 2.5 MHz and 5 MHz networks active, although I'm only using version 2.5, but they have different sid, and I'm on the network with and without port forwarding 2.5 on.

  Any suggestions will be greatly appreciated

  Okay, I found where the problem was, and I apologize for having raised this issue just because I made a very stupid mistake. It turns out that I had added DNS servers external (outside my local file/mail/DNS server) to the list on my router (and I forgot about it). Cancel the additional DNS resolvers seems to have solved the problem. I'm far from understanding how the DNS works really, as you can see.

• Unable to do port forwarding, to connect to the VPN and install Windows updates

  first of all, I tried to launch a minecraft Server trying to port forward, had problems with this, so I tried Hamachi, wouldn't connect to the VPN, then I tried Tunngle, at least, it was more useful, so I tried to use Device Manager to search for tunngle found when trying to manually install it, then he said that he could not or invaild something (or something of the sort) then it says windows may need to be put updated to fix this problem, so I tried to update to windows and it will not be updated, he is stuck at 0%, I tried the thing to download the patch to update windows and that has not helped,): I DO

  Original title: Windows Update will not be blocked at 0%

  Hello

  Thanks for posting your query in Microsoft Community.

  Depending on your problem troubleshooting to establish a VPN connection, I recommend that you post your question in the TechNet forums. TechNet is watched by other computing professionals who would be more likely to help you.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro

  Hope this information is useful.

• Port Forwarding issue with HP Photosmart C7250 / Windows 7 / Linksys router

  Help, please! I worked on this problem with HP, Microsoft, No - IP.com, etc with no resolution.

  I have a 650 workstation DELL computer in office which has been recently formatted and had a clean install of Windows 7 will be of all installed updates. He is running Free AVG 9.0. There is a Linksys WRT54GS Wireless with disabled DMZ and Port 80 (only) active.

  I have installed no.-solution of IP.com for the creation of a hostname to point to my dynamic IP address.

  I need to have Port 80 go to the IP address of my PC so that I can set up synchronization option Wireless of my CRM with my iPhone and Blackberry. Instead, whenever I created the public IP address or host name, it brings me to the Web Interface of my HP Photosmart C7250 printer. Even, I assigned a static internal IP (and DNS) address to the printer (192.168.1.101) but no matter what I do Port 80 goes into that compared to the IP from my PC to 192.168.1.110 which is the IP in my router.  The printer is set up wireless on Channel 6 (WEP encryption).  UPnP is disabled.

  I called HP and they said, there is no place that port forwarding is enabled. This doesn't seem to be the case. I tried to change the internal IP address of the PC to 192.168.1.101, but it had nothing works (could not ping or pull up the Web Interface for HP). I tried to add a different port number and it doesn't work.

  I need Port 80 to connect to my IIS server. Microsoft says that this is but another State Tech that disrupts the HP software. From the HP Web Interface, it is what appears when I type in my host name or public IP address and it's not going to my PC, then I have a tendency to agree.

  FYI... I unplugged the printer and now when I try to ping the public IP address, I always get a response (even after half an hour of the printer being disconnected). Please HELP ASAP! Thank you!!!

  Solution - on secondment in case anyone else ever runs into this.  Update the firmware on the Linksys router did the trick!

  From and upward... FINALLY!

• Need help with the implementation of a VPN to bypass the port forwarding to access my web server

  Pretty much as the title suggests, but it's probably not clear enough. Let me explain:
  I want to host a Web site on my computer. Not another major, but something small and private.

  Before you set up a domain name, I want to make sure the site works - which it is not.
  I am currently using WAMPServer to organize it all.

  I put it so when I connect to localhost, I have access to all my files in the directory, regardless of whether or not I'm "online" or "offline" on WAMPServer (or not, others will have access to my Web page).

  When I turn WAMPServer 'on-line', it allows the connection of my WAMPServer homepage through both localhost and connection through the static IP address, I put in place, but only in LAN, meaning that only computers connected to my home network would have access to the page.

  My router cannot be configured to allow port forwarding for can I open a port to allow redirection to my computer, rather than the ambiguous router itself. As an alternative, I downloaded Hamachi to allow a computer to connect to the VPN (Hamachi) and, by extension, my IP for access to files in the directory.

  In theory, it should work, but it didn't. In my local network computers could still connect to the IP address, but the computer in the virtual private network, but not on the local network could not.

  Is there something I'm missing here, or is there any suggestions to make this work?

  Note:
  My works of static IP as what it is, however, it is different from the IP address used in Hamachi. If I change the IP address used by my computer to access the site to the IP address that uses my Hamachi, would that work? As another suggestion, can I change my static IP setting is automatic and change one used on WAMPServer (from localhost, allowing the connection to bring) than on Hamachi? Or I do all three IP addresses the same?

  Thanks for all the help and solutions,
  Elgo

  Domain/server/business questions are best addressed @ Technet.  Answers is more connected consumer.

  http://social.technet.Microsoft.com/forums/en-us/categories/

• port forwarding for file sharing on the internet.

  I am trying to determine what port numbers, I need to transfer to my router (in virtual server) to be able to share my NAS files over the internet with my friends? I want to use file sharing, have implemented a DDNS on the NAS with a client account to my dynamic IP address, but cannot get the numbers correct port developed to be able to configure port forwarding. Can anyone help?

  Hello

  Open sharing Ports that are used on a local area network on the Internet is a Big safety hazard.

  There are secure applications that are built for this purpose, they use their own ports and generally are safe (as on the VPN or SSH).

  A free quick simple way is shared through secure ftp server. http://FileZilla-project.org/

  An elegant way door application like this, http://download.cnet.com/WebDrive/3000-2160_4-10017919.html

  In general, http://www.practicallynetworked.com/howto/fileshare/fileshare_intro.htm

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• How to configure port forwarding on a dedicated server running CentOS 5.4 to use Ubuntu 9.0.4

  The basic situation that I have is a dedicated server running CentOS 5.4 for the moment I have a virtual machine running Ubuntu 9.0.4. Later, I want to add a virtual computer that is running Windows Server 2003, but right now I focus on the implementation and running Ubuntu.

  The installation of Ubuntu works very well, but I am seriously struggling to get the port forwarding so I can visit the Web sites to be hosted on the Ubuntu VM. As a newbie on Linux, I am confused about the relationship between IPTables and VMWare own port forwarding.

  Here's what I've tried so far.

  My server's IP address is xxx.xxx.xxx.xxx, provider support told me that the subnet mask is 255.255.255.0, gateway address is xxx.xxx.xxx.1 and the network address is xxx.xxx.xxx.0. (These last two surprises me a little, I'd expect to be private rather than public gateway/network address).

  First of all, I tried Bridged Networking, but had no luck contacting the machine other than through the VMware console. I tried it the ping from the host (using ssh in the host), but no joy. also no Inernet access from the VM. I changed the configuration of the DHCP server to static interfaces, using a static address 192.168.1.100 and by assigning to the doors of such xxx.xxx.xxx.1 as advised by the supplier. No real difference, still cannot ping the host prompt, or vice versa and any of the customer's Internet access.

  Then I tried NAT. The host automatically 192.168.132.128 with a 192.168.132.2 gateway IP address now, the client has access to the Internet and when I do a VNC host and open Firefox with 192.168.132.128 I can see the correct hosted Web site but I still can't get in from the outside.

  I mentioned that I am a bit confused about IPtables and VMware port forwarding, what I wanted to say, it is that I'm not sure if IPtable transfer must be set to the IP address of the interface of comments (192.168.132.128 in this case) or the address of the 192.168.132.2 bridge.

  I have the impression that I'm missing something simple here, can someone tell me what it is?

  Find your "/ etc/vmware/vmnet8/nat/nat.conf" file and change:

  Example:

  \[incomingtcp]

  8887 = 192.168.27.128:80

  That would redirect a header of TCP packet entering the port 8887 on the host on port 80 of the guest with the IP 192.168.27.128.

  Ditto for the UPD:

  \[incomingudp]

  6000 = 192.168.27.128:6001

  You can (must) use iptables for firewall purposes but does not redirect traffic at the prompt.

  Read page 252 in the Manual: http://www.vmware.com/pdf/vmserver2.pdf

  AWo

  VCP 3 & 4

  Author @ vmwire.net

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• Port forwarding for EYEMAX DVR on WIn Server 2012

  We use the router as a network controller on our local network. Now, we have replaced router with the server (win 2012 r2 essentials). We have an EYEMAX DVR client software to connect to a remote ip address in the web.

  Previously, I had the configuration of port forwarding router and EYEMAX was working. When we replaced the router with a server that I can no longer connect. I guess that there is a similar setting to perform on a server, but I can't figure out what to do. This certainly isn't a Firewall (when I turn it off EYEMAX still do not work).

  There is a statement (http://site.camtechsurveillance.com/downloads/remoteacc.pdf) how to configure a router to work, but I do not know how to apply similar changes on the server.

  TL; DR.

  How to do the same on the server like here http://site.camtechsurveillance.com/downloads/remoteacc.pdf

  Try asking in the Windows Server forum:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• LRT214 Port Forwarding does not

  First of all, when you create a service in the port forwarding section, why to select the two TCP/UDP has been omitted from the selection must be embarrassing for Linksys.  Creation of 2 services, one for the other for UDP and TCP are bad design.  Would love to see that this problem has been corrected in future updates of the firmware.

  The main problem is I have configured port forwarding services, but I can't get anything to work.  I am able to access remotely to the router using the port 1443 that is configured in a separate section.  I worked in the network design and mgmt for 10 years and why Linksys decided to make the management for the LRT214 so different interface, then the rest of the market was a bad decision.  Is there anything else you can suggest to help out why these ports cannot be opened through the FW?

  On this router logs show nothing.  There is no log for blocked inbound connections and there is a class router business?

  After setting up some boxes of Windows on the local network, then transfer to a custom RDP listening port, I am able to RDP in these Windows boxes remotely.  It verifies that the Linksys router is forwarding ports correctly.  The question then is something on the Synology device itself.  Thanks for your response!

• Port forwarding on WRT54GL does not

  Thanks in advance, trying to track forward setup my linksys WRT54GL allow Remote Desktop from outside your desktop (private static IP).

  I have a configuration of modem netgear in bridge mode (so the firewall is disabled on the modem), and the Linksys WRT54GL Firewall enabled, with "filter internet NAT redirectin" unchecked.

  I also, port rule before the Setup program in the game & Apps, to transfer the TCP 3389 to my office (private) static IP address.

  I make sure firewall is not blocking the RDP traffic, and I can RDP on the desktop to a laptop on the WIFI network.

  But the rest of the world, I can't not RDP using my ISP (dynamic) IP address.  times out.  I don't know that I have the IP address of my ISP at the moment.

  Thoughts?  I present screenshots if necessary

  After further digging... I found the problem, it was with the Windows 7 firewall.

  I made sure 3389 (and RDP application) was allowed on Win Firewall (this is why I could RDP on my WLAN), but for the rule of the RDP, under the "Advanced" tab, I also had to "allow the crossing side.

  It was the first time I set up the port forwarding for a box of Win 7, so didn't even know that this setting exists in Windows 7.