Impossible to log into Admin and will not be able to edit my site.

Similar Questions

• tracert stops and times out to 63.245.5.149 and will not allow access to a Web site

  Hello. I just had Qwest install internet in my house that my mother--brother-in-law can enjoy Polish television online. Excited, she immediately tried to go to his Web site (www.polwizjer.com), to watch his shows, even when she tried to go to the site, there was an error: the connection has expired; the server for polwizjer.com takes too long to respond. all the computers in my house got the same error message or similar, so I tried ping on the site, without entering. I tried on a whim to get the website using my phone as a lanyard... it worked, then I did a tracert from the site (by using the internet service of qwest) and it always stops at a specific IP 63.245.5.149 and out of time. When I called qwest, they pretty much had me repeat steps, already tried in a session in case of problem, but it got us nowhere, however they belive it is something with the server of this IP address or something. (FYI, I'm still learning computers and I have only a few pretty basic skills and knowledge of the functioning of routers and how to trouble shoot minnor issues like these)

  Is there a way to change my itinerary so that we can access this Web site, or can I change service providers... or even changing ISPS will solve the problem? All suggestions are welcome and thank you in advance

  C:\>tracert www.polwizjer.com

  The route to www.polwizjer.com [200.74.244.124]
  with a maximum of 30 hops:

  1<1 ms   =""><1 ms   =""><1 ms ="">
  2 20 ms 21 ms 20 ms hlrn-dsl-gw77 - 142.hlrn.qwest [207.225.112.14 .net
  [2]
  3 22 20 21 hlrn - .net [71.217.190.97] agw1.inet.qwest ms ms ms
  4 ms 50 ms 43 45 ms dap-brdr - 03.inet.qwest .net [67.14.2.85]
  5 44 44 45 ms 192.205.35.53 ms ms
  6 78 ms ms 77 77 ms cr1.dlstx.ip.att.net [12.122.87.14]
  7 ms ms 77 76 ms 76 cr2.hs1tx.ip.att.net [12.122.28.158]
  8 ms 76 76 ms ms 81 cr1.ormfl.ip.att.net [12.122.1.6]
  9 75 ms ms 76 78 ms gar2.miufl.ip.att.net [12.122.143.41]
  10 76 78 ms ms 78 ms 12.116.154.18
  11 87 86 87 [6 xe-0-1-1-nmi-teracore01.columbus-networks.com ms ms ms
  3.245.5.108]
  12 82 ms 79 ms so-3-0-2-pan-edge02.columbus-networks.com [63,24 78 ms
  5.5.145]
  13 112 ms 112 115 ms 63.245.5.149 ms
  14 * request timed out.
  15 * request timed out.
  16 * request timed out.
  17 * request timed out.
  18 * request timed out.
  19 * request timed out.
  20 * request timed out.
  21 * request timed out.
  22 * request timed out.
  23 * request timed out.
  24 * request timed out.
  25 * request timed out.
  26 * request timed out.
  27 * request timed out.
  28 * request timed out.
  29 * request timed out.
  30 * general failure.

  Full trace.

  the above is my tracert with my ISP qwest at home

  All good suggestions, but by changing the IP address does not work. The Web server swear that they do not deny any address. I don't know what it could be. 1 million of laurels to the guru that find this baby!

• How to build a model dreamweaver help than a fluid grid.  My file/save model is grayed out and will not aloow me to save my site as a template page.  Thank you

  Can I do a fluid grid layout template.  If yes how to accomplish this?

  It does not strip the CSS from your code.  If done correctly, deceive you DW thinking that it is a non fluid grid which allows to use design mode.

  Just add an X to code CSS FluidGrid that generates DW for you when you create a new FGLayout.

  Properties Grid Dreamweaver fluid

  ----------------------------------

  DW-num-CLO-mobile: X 4;

  DW-num-CLO-Tablet: 8;

  DW-num-OCOL-Office: 12;

  DW-gutter-percentage: 25;

  =====================================

  To do this, you must manually change the CSS code in Code view. Record. DW to close and reopen DW.

  To return to the mode of FGLayout, you will need to remove the X.  Record.  DW to close and reopen DW.

  Nancy O.

• I'm on mac osx 10.5.8, but FireFox gives me a message that it is not compatible with my version of Mac OS x and will not let me install. The site says it's compatible with os x 10.5. Am I missing something?

  I managed to download the latest version of FireFox, but when I tried to install, I received a message that FireFox is not compatible with my current operating system. What else should I consider or try to get FireFox to work?

  You are on the PPC. The latest version supported for a PPC computer is 3.6.24. You can download this version of http://www.mozilla.com/en-US/firefox/all-older.html

• Disabled the SATA in the BIOS by mistake and will not be able to access the BIOS

  I disabled pata and sata by mistake in the bios on compaq windows vista desktop

  I can't go beyond screen compaq or access in the bios can someone help me with this please

  Hello

  For any problems with your Compaq BIOS, please contact HP direct.

  http://WWW8.HP.com/us/en/contact-HP/contact.html

  Or ask in the Forums of HP's Support.

  http://h30434.www3.HP.com/

  See you soon.

• Try to reinstall the printer and will not install due to not having Admin rights

  original title: Instalation printer

  Try to reinstall the printer and will not install due to not having Admin rights. I am the administrator,

  How can I continue?

  Thank you

  Right click on the printer software setup.exe, etc > run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite Pro L450D black screen and will not respond to any keys

  Hello

  My niece has used his Toshiba L450D for almost a year now and he really liked it, who was until last month. She turned on her laptop and when she presses the button of the mouse, the button cracked and he fell into the laptop.

  Now my brother contacted Toshiba and I was told because it is under warranty it might return for repair because it was a common fault. Then he he packed in loads of air bubbles and a box to make sure it was safe.

  A few weeks later he came back repaired but we were all shocked that the laptop was put in a very loose box and you could hear this rattling noise. When we turned on the battery was flat and we had a new boot menu.

  As she installed it Windows 7 laptop would boot directly into Windows 7, but now after the repair of the laptop shows a menu black screen with as follows:

  + Windows 7 +.
  + Recover Windows to Factory Settings [active EMS] +.

  So we started in Windows and everything went well, but now after 5 or 10 or even 20 minutes, laptop displays a black screen and will not respond to keys or mouse movement. There is nothing on the screen its just black.

  I started in SafeMode (which was more difficult with the new menu) and it does the same thing. I even managed to do a virus scan quick who took 3-4 minutes and was clean.

  I would like some advice on what my niece is very angry, and it's difficult to explain what is happening to a child in the primary school.

  Any help would be grateful.

  Hello

  Have you tried the option of HARD drive recovery?

  If this is not the case, try to set the notebook back to factory settings using HARD drive recovery.
  Turn on the device, press F12, choose repair my computer, then select Toshiba HDD recovery.

  I hope it will work!

• I just replaced my MB Pro with a MB Air. Air has less memory and will not support a full restore of files and the saved data. How to do a partial restore

  I just replaced my MB Pro with a MB Air. Air has less memory and will not support a full restore of files and the saved data. How to do a partial restore

  Do you still have the MBP? If so you can manually copy and paste the files you need.

  If you do not have the pro more, you need to buy a USB key and plug it into the MBA... use it as a target. Once you have a system file of the previous laptop again, you have to manually choose what to copy across.

• Keyboard Dell Bluetooth is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.

  My Dell Bluetooth keyboard is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.  I use keyboard now, but it seems not be installed yet when I check my keyboard or bluetooth devices. Keyboard does not work after so I'll try to figure out what to do before moving into the power saving mode. Help, please. I did all the updates from microsoft, and there is no update for my bluetooth device, I checked.

  Hello

  1. have you made changes on the computer before this problem?
  2. What is the model of the keyboard?
  3. are you an error message or error code?
  4. which version of the Windows operating system is installed on your computer?

  I suggest you to consult the following Microsoft article and check if it helps.

  On troubleshooting in Windows 7 power management: http://support.microsoft.com/kb/980869

  Troubleshoot keyboard: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-keyboard-problems

  Keyboard and Microsoft mouse refer:

  Troubleshoot the incidents of the response to the mouse or wireless keyboard: http://support.microsoft.com/kb/838398

  Reference:

  Troubleshooting external Dell Wireless or Bluetooth keyboards and mice: http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=277550#Issue0_1

• HP psc2100 series all-in-one: printer was working fine, all of a sudden its impasse on copy and will not be printed said export error

  computer printing problem saying "Error exporting" and printer saying just 1 copy.  I tried troubleshooting on mine, doesn't have the verified maintenance on the printer, but still saying error. Help, please!

  Hi @kelley22,

  Welcome to the HP Forums!

  I see that your HP PSC 2100 printer is stuck on copy and will not be printed on Windows 8. I'm happy to help you!

  The first step, I would like to recommend is a hard reset. Please see this message, How to perform a hard reset, by @Rich1. It is very important that the power cable from the printer is plugged directly into the wall outlet, not a surge protector. See this article, questions when it is connected to an uninterruptible power supply/Strip/surge protector power, for more information. This is true for printers and ink jet.

  Once this step is finished, please try to print a self-test report, to check the printer hardware is fully functional.

  To print a self-test report, follow these steps:

  • On the product control panel, press Setup.
    The installation menu appears.
  • Press the right arrow ( ) until print report displays and then press OK. The menu print report appears.
  • Press the right arrow ( ) until the self-assessment report and press OK. The self-test report prints.

  If the test report print, then on the computer, please try our HP print and Scan Doctorand let me know what happens!

  Hope this helps and have a great day!

  "Please click the Thumbs up icon below to thank me for having responded."

• just turned on computer all the safety devices are disabled and will not not turn on ie... MSE DEFENDER FIREWALL

  just turned on computer all the safety devices are disabled and will not not turn on ie... MSE DEFENDER FIREWALL

  Vista Home premium 32-bit

  Hello

  Malware to disable your firewall and your safety programs.

  Scan of Malware in Safe Mode with network.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Once in Safe Mode with network, download and run RKill.

  RKill does NOT remove the malware; It stops the Malware process that gives you a chance to remove it with your security programs.

  http://www.bleepingcomputer.com/download/rkill/

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And also scan with the free version of SUPERAntiSpyware

  http://www.SUPERAntiSpyware.com/download.html

  SUPERAntiSpyware Free Edition is 100% free and will detect and remove thousands of Spyware, Adware, Malware, Trojans, KeyLoggers, Dialers, Hi-Jackers, and worms. SUPERAntiSpyware features many unique and powerful technologies and removes spyware threats that other applications fail to remove.

  SUPERAntiSpyware Free Edition does not include blocking in real time or scheduled scan.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  THS is a very good program to scan your system to remove adware, etc.:

  http://www.bleepingcomputer.com/download/adwcleaner/

  AdwCleaner is a program that finds and removes the Adware, toolbars, potentially unwanted programs (PUP) and browser hijackers from your computer.  Using AdwCleaner you can easily more of these types of programs for a better user experience on your computer delete and while browsing the web.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  And just to be sure, nothing is lurking in the background:

  'TDSSKiller Rootkit Removal Utility download for free'

  http://USA.Kaspersky.com/downloads/TDSSKiller

  ABon the Defender being turned OFF

  With MSE installed Windows Defender is supposed to be disabled.

  MSE has been designed with its own version of Windows Defender under its own program.

  If the two were running, it would cause system conflicts.

  See you soon.

• Connection problem: trying to connect to my computer at the title of the administrator, but after I put my login in it goes to check on the page and will not let me connect

  Try to connect to my computer as the administrator, but after I put my login in it goes to check on the page and will not let me connect. The regular connection for the computer works fine.  Any ideas?

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  It is the instance of Vista installation.

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/threads

  Adjust settings, manage user accounts.

  Try the Forum above to repost, if necessary.

  See you soon.

  Mick Murphy - Microsoft partner

• Printer is offline and will not print documents

  Printer is offline and will not print documents, the rocker switch "Printer offline" option is not available and it is constantly check on 'printer offline '.

  How can I fix this so I can print the necessary documents?

  Hello destiny.

  Welcome to the Microsoft community. I appreciate your efforts to resolve the issue. I will certainly help you with the problem you are experiencing.

  The description of the problem seems a little unclear and I wish I had a better understanding before you start working on it. I would be grateful if you could help me with more information.

  • Is the printer connected directly to the PC or it is on a network?
  • What is a printer wired or wireless?
  • What is the brand and model of the printer?

  Try the following and see if it helps.

  Method 1: Disable Antivirus

  If you have installed any third party such as antivirus or firewall security software, I would say you temporarily disable and check if it works.

  Disable the anti-virus software

   

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attack.

  Method 2: Update the drivers for your printer.

  For more information, see these links:

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Find and install printer drivers
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  
  Method 3: Restart the print spooler service.
  You must be logged on as administrator to perform these steps.
  a. open administrative tools by clicking the Start button, then Control Panel. In the search box, type administrative tools, and then click Administrative Tools.
  b. double-click on Services.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  c. right-click the print spooler service and then click Properties.
  d. on the general tab, next to startup type, make sure that automatic is selected.
  e. If the service is not already running, under Service status, click Start and then click OK.  If you are prompted for an administrator password or a confirmation,
  type the password or provide confirmation.

  If nothing works, then manually add the printer to the local port and check.

  Method 4: Manually add the printer to the local port.

  a. go to control panel and click on devices and printers.
  b. click Add a printer, and then select Add a local printer. Click on create a new port. The default value in the drop-down list is Local Port. Don't change that.
  c. click Next.
  A dialog box appears for you request that you enter a port name. Type the name of \\computer name\printer.
  d. type your user name and the name of the printer (name \\PC\printer)
  e. click ok and exit.

  See also:
  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

  http://Windows.Microsoft.com/en-us/Windows7/file-and-printer-sharing-frequently-asked-questions

  Hope this information was useful. Let us know the results once you have tried these methods. We will be happy to help you further.

• Photoshop 2015.5. PS does not update and will not open. Missing 4 dll files.

  Photoshop CC (2015.5). PS does not update and will not open. Missing 4 dll files.

  VulcanControl, VulcanMessage5, tbb and ScCore. PS worked fine earlier today and has worked great for over a year.

  Windows 7 update to 10 eight months ago.

  Exit code: 184

  -------------------------------------- Summary --------------------------------------

  -fatal error 2, 0 error (s), 1 warning (s)

  FATAL: Error (Code = 184) running the 'MoveFileCommand' command for package: 'AdobePhotoshop17-Core_x64', version: 17.0.1.159

  FATAL: An error has occurred in the installation of the package (name: AdobePhotoshop17-Core_x64 Version: 17.0.1.159). Error code: "184".

  WARN: Cannot move the card to the address 'C:\adobeTemp\ETRD35C.tmp\1\Application\Required\DynamicLinkMediaServer\32\libmmd.dll' to 'C:\Program Files\Adobe\Adobe Photoshop CC 2015.5\Required\DynamicLinkMediaServer\32\libmmd.dll' error 32 the process cannot access the file because it is being used by another process... Try setting the correct permissions for the specified file/folder or parent, so that the admin has the right to modify.

  Hey gene,.

  Thanks for getting back to me. I uninstalled and re-installed PS and everything seems to work very well. Put same Lightroom update. Not sure what the problem was.

  Thank you

  Clay

• My IPad sudenly turned off and will not restart. It is fully charged.

  My IPad sudenly turned off and will not restart. It is fully charged.

  What you have tried so that he could begin until For example you soft-reset/reboot trieda? Press and hold the home button and sleep for about 10 to 15 seconds, then the Apple logo will appear if all is well and it will start.