in Cisco licenses a single model controller WLAN HA
Hi all
I am performing an estimate on the CCW. I have to configure a wireless controller with 12 licenses the AP based on the Cisco model. Please find below the BOM:
C1-AIR-CT5508-K9 | Range Cisco ONE - 5500 controller WLAN w / 0 AP PFR |
CON-SNT-CT5508K9 | SNTC-8X5XNBD C1-5500 Wireless LAN Con w / 0 AP PFR |
LIC-CT5508-BASE | Basic software license |
ECMU-CON-LICCT8BAS | Southwestern Scotian platform upgrades the software Base Licens |
C1-MSE-PAK | Cisco MSE license a PAK |
C1FPAIRK9 | Cisco ONE perpetual Foundation - wireless |
ECMU-CON-C1FPAIR | Southwestern Scotian platform is LEVEL C1 perpetual Foundation - wireless |
C1-WLC-1 | THE Cisco Wireless LAN Controller PA license (any WLC) |
C1-WLC-PAK | THE Cisco Wireless LAN Controller AP License PAK (all WLC) |
C1-PI-LFA-AP-K9 | PI license Cisco FOR LF & as WLAN device |
C1-ISE-BASE-AP | Cisco identity services 25 Lic endpoint database engine |
C1-MSE-LS-1 | A Base of CMX Cisco (location + Connect) - 1AP license |
C1-CEM-25-K9 | Cisco energy Mgmt Perpetual Lic - 25 end Points |
C1-CAND-1 | Cisco connected THOSE Analytics Net deployment - 1 Dev Lic 1 year |
C1-LC-5-1Y | Cisco a 5 fps 1 year Lic StealthWatch |
C1F1VAIR-02 | Tracker PID v02 Fnd Perpetual AIR - no delivery |
SWC5500K9-80 | Cisco Unified Wireless Controller version 8.0 SW |
AIR-PWR-CORD-THIS | AIR Line Cord Central Europe |
AIR-PWR-5500-AC | Cisco series 5500 redundant power wireless controller |
Now, I have to configure a controller HA. In the CISCO model, the SKU is the same as the controller, which I configured above.
Configure the controller HA without AP licenses?
Please give me the best way to configure the WLC HA in the Cisco model
Hi Angel,
If you get a C1-AIR-CT5508-K9 , then you should not have licenses on the secondary unit (who you called unit HA). However if this is not the case then the usual requirement of license AP 50 County should hold to convert a secondary WLC. The number of licenses AP 50 can be registered license C1-WLC-1 pool.
Hope I was able to clear the confusion.
Best regards
Learn from the best to be the best!
Change the way you look at connectivity of wireless clients forever by registering to watch this free webinar and also a chance to win our starter kit worth $ 8000 wireless for free!
Tags: Cisco Wireless
Similar Questions
-
Unable to apply the model of WLAN to the controller through WCS
Unable to apply the model of WLAN to the controller through WCS
1 update your config all of your controllers of WCS. Go to configure---> controllers--> select all controllers.
2. in the drop-down "Select", choose "refresh the configuration from the controller and select 'Go'."
3. choose Delete therefore WCS will take the last setting of the WLC and select 'go '.
4. remove the WCS WLC.
5. Add WLC to WCS.
6 try to set up the model again.Also, you can upgrade to 6.0.170 as there are to many model feature bugs that have been fixed in this version.
http://www.Cisco.com/en/us/docs/wireless/WCS/release/notes/WCS_RN6_0_170.html#wp44440
-nael
-
brand/model of WLAN adapter
I try to find the wifi adapter make and model for my new HP Pavilion 15 t-n200 CTO recently go. I decided to do a new install of Windows 7 x 64 but I forgot to write down the make and model of wlan before I wiped the hard drive. I downloaded and installed the Realtek RTL8188EE 802.11b/g/n Wireless LAN Driver but with an error. It works fine, but I wonder if it is the wrong driver and you need to install the MediaTek (Ralink) 802.11 b/g/n Wireless LAN (WLAN) card driver or the Ralink 802.11 b/g/n Wireless LAN Adapter Driver instead.
It turns out that I got the correct driver after all. Everything indicates that he didn't install properly but is not true.
-
Hello
I'm new with Cisco licenses... I produced Cisco ASA 5505 in house with base with the limit of 10 hosts license. More information below.
I bought the 'L-ASA5505-10-UL =' upgrade remove limit hosts and I got the certificate with Pak. But when I go to the licenses of Cisco website to get the key of activation with this PAK I you will get the error message below.
Unfortunately I didn't take in charge of the contract so I can not open a Service request as said.
Any help what to do?
Error message:
Bad Sku (s) 'L-ASA5505-10-UL =' for 'ASA5505-BUN-K9': device contains the licenses following "K9-BA-ASA5500.
Serial number = JMX1526Zxxx
We're sorry, but the serial number provided is not the same type of platform that serial number has failed. An upgrade is requested is not permitted.
If you want assistance in solving this problem, please open a Service request by using the TAC Service request tool
> View version
The devices allowed for this platform:
The maximum physical Interfaces: 8 perpetual
VLAN: 3 restricted DMZ
Double ISP: Disabled perpetual
Junction VIRTUAL LAN ports: perpetual 0
The hosts on the inside: 10 perpetual
Failover: Disabled perpetual
VPN - A: enabled perpetual
VPN-3DES-AES: activated perpetual
AnyConnect Premium peers: 2 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 10 perpetual
Total VPN counterparts: 25 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy UC phone sessions: 2 perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: disabled perpetual
Intercompany Media Engine: Disabled perpetual
This platform includes a basic license.
See you soon,.
Henri
It's an automatic response, or a person actually answered? License Rep must respond to your e-mail. They would be able to rehost the license for you.
-
What layer are FI in the Cisco hierarchical network design model?
What layer are FI in the Cisco hierarchical network design model?
Is this a straigh question? We have a Nexus 7 k for our heart and Port-channel of the FI for them. So for me it layer distribution.
But when we attach to the NAS. Isilon devices we use between the FI and N7K N3K. This would make the N3K and FI both part of the Distribution layer? Would not be considered layer. However, it does not ACL etc. which usually belong to the Distribution layer.
I was wondering thoughts people on it. Is the UCS FI and 'One Off' in the model of 3 layer?
Thank you!
Craig
FI can sit to your dist layer. or access. I've seen deployments where they are deployed at the same time, depending on the size of the cluster of the UCS and band network bandwidth. The distribution layer is usually to be where all the magic of layer 3 arrives (routing, ACL, QoS, FW, application of strategies etc.) and UCS being strictly Layer 2, it could be classified as a device to access-layer.
Designs are flexible and as long that you consider oversubscription adjusted, you should be fine with the deployment option.
I hope that others will share their ideas
Kind regards
Robert
-
Cisco 526 Wireless Express Mobility Controller supports AIR-LAP1140N?
Does anyone know if Cisco 526 Wireless Express Mobility Controller supports the AIP-LAP-1140N Access Points?
This isn't. The WLC526 supports only the AP521.
HTH,
Steve
-
Hello
I'm new on WCS lil... I upgraded my WCS now to 5.1.64... WCS has already a couple of controllers mapped with about 40 LWAPP...
I see an inconsistency in WLC - WCS configuration, on the model of controller... When I change the configuration of the model on the WCS, it updates the WLC somehow? I am cautious about is I don't want to disturb anything either with the WLC running is, by changing something on the WCS...
I have also 2 new controllers added to the WCS... I need to set controller models for these... Can I directly configure this and associate the new WLC to the new model? Yet once, model controller in WCS will apply to the new WLC?
Raj,
In this case, you can add new controllers to WCS with RO SNMP community strings. Then go to configure--> controllers and check the box next to one of the controller. From the controls menu select 'discover controller models. This will automatically create WCS models based on the configuration of the controller you selected. Follow the same process for all controllers.
You'd be using community RO, WCS strings would not involve no change. You will now be able to verify correctly.
--
Pushkar
-
Questions of VLAN and configuration for Cisco AIR-CT2504-25-K9 Controller
Hello
It's my first time thanks to the Cisco wireless solutions, so I was hopping someone could help me with the following:
We just bought the AIR-CT2504-25-K9 controller with some points of access for the AIR-CAP1702I-E-K9.
The network is as follows:
Peripheral layer 3 (managed by third parties): it's on the domain network. (VLAN by default, 1 - unidentified)
ADSL router - it's the network without comment thread. (Default Vlan 4 - tagged).
VOIP: VLAN 5.
Both fittings go into a switch Cisco SG500 52 (Layer 2). There is a port to shared resources on the switch SG500 with VLAN 1 (Tagged) and VLAN 4 (with tag). The WLAN controller is plugged into this port trunking.
The data and management network are in the same subnet and on the same VLAN (1).
I used the wizard on the controller setup.
There are three interfaces:
management VLAN ID 1 IP 192.168.1.2 Port 1 (configured with a gateway domain network, DHCP, etc.).
VLAN wireless identifier 4 IP 192.168.5.1 Port 1 comments (configured with modem router ADSL, DHCP, etc.).
Virtual IP 192.0.2.1
Proxy DHCP active overall.
There are two wlan networks:
(1) area - management Interface - SSID abc.
(2) comments - comments Wireless Interface - SSID xyz (the wizard put to management, but I changed it to the wireless).
Are the AP connected to another SG500 switch which is shared resources to the switch with the controller.
Ports of the APs are connected to have only 1 VLAN unidentified. They don't have 4 VLAN Tag or not identified. However, everything seems to work as expected.
When I join the guest network (SSID xyz), I get an IP address from the router ADSL and all Internet traffic goes through him. When I connect to the domain network (SSID abc), I get an IP address from the DHCP in Windows Server and all traffic goes through the device of layer 3 (I checked the public IP address in my browser). I can't ping anything from one network to the other.
My questions are the following:
(1) how the guest network traffic (VLAN 4) headed the APs controller when they are connected to the ports on VLAN1? Is it because the traffic is encapsulated?
(2) is set up correctly? After you configure the controller, I saw a note in the forums, this State I can simply enter 0 for the management of VLANS to let it not identified. However, in my case, I kept it as 1, which is the same as the switches and then the tag VLAN on the switch. In addition, the set Wizard wlan of comments to use the management interface but I changed it to use the comments interface.
(3) when I connect to the APs of the controller, I see several options that can be configured manually. Is it necessary for this? For example, there is an option of data encryption.
Thank you
A
Hello
(1) how the guest network traffic (VLAN 4) headed the APs controller when they are connected to the ports on VLAN1? Is it because the traffic is encapsulated?
Yes, I'm with CAPWAP:
More information: http://lets-start-to-learn.blogspot.de/2014/08/cisco-wireless-understand...
(2) is set up correctly? After you configure the controller, I saw a note in the forums, this State I can simply enter 0 for the management of VLANS to let it not identified. However, in my case, I kept it as 1, which is the same as the switches and then the tag VLAN on the switch. In addition, the set Wizard wlan of comments to use the management interface but I changed it to use the comments interface.
If you want that mgmt interface must be unmarked and then put 0 otherwise you can use vlan 1.
I do not have what is configured under mgmt and comments interface, but according to the name I'll say yes, you must set the comments under comments wlan interface.
(3) when I connect to the APs of the controller, I see several options that can be configured manually. Is it necessary for this? For example, there is an option of data encryption.
Yes, there are many things that you can configure, but I'll leave most of the default of things unless you really need to change!
The following best practices: http://www.borderlessccie.net/?p=270
Concerning
Remember messages useful rates
-
HP laptop - 15-r249tu: more than 1 Wifi drivers for a single model. Why?
Hello
I tried to download the drivers for my laptop ' HP for laptop - 15-r249tu "for Windows 8.1 x 64 to this link. But there is a problem. Which driver to download and install? I mean, under driver-network, there are drivers for WLAN provided by Broadcom and Qualcomm both. It is the same with Bluetooth. Which one should I download and install. Don't you know that this model has this device? In addition, versions of the drivers are listed separately. Shouldn't there be an option as
Manufacturer and model #.
|---> Version 1 (download)
|---> Version 2 (download)
|---> Version 3 (download)
Please don't suggest me to use the utility to auto detect. I just HATE IT! Please provide an option to choose which drivers to download manually and then export their links to download a file *.txt or both
Any help and action will be significant.
Dev
Hello:
It is a peer to peer forum.
I am not employed by, nor should I represent HP.
I guess HP reorganizes the pilots in the entire series (different model numbers within this series with some different material), because to do otherwise would be too heavy and expensive to maintain the support pages.
In any case, here are the drivers wireless and bluetooth, that you need for your laptop model specific in accordance with the list of parts.
-
Time changes of WLC cisco by default whenever the controller restarts
I have cisco wlc 2500 series and 1700 AP I configured the controller, but to my surprise, whenever it restarts, the time is adjusted to the time default 2000 AD.
1. do I need to change the NTP server? We do not have the NTP server, so in this case what IP should I use?
2. is there a way to fix this? I had configured other 2 controllers as well but it I do not encounter this kind of problem, so did I missed something?
Help, please.
1. do I need to change the NTP server?
A NTP is strongly recommended.
We do not have the NTP server, so in this case what IP should I use?
Configures the Basic (core router or switch) device to go to the internet for NTP synchronization. Then configure the WLC to synchronize to the core router or switch.
-
Cisco 526 Wireless Express Mobility Controller
We just bought to UC520, 526 and a LAP521 controller. We got the UC520 upward and running in 15 minutes, but the 526 does not include a lot of documentation. Can not have find the 521 AP on the network nor will it set the layer mode 2. I don't want to configure routing for a 4 Office of PC couche3. During installation, the only option it gives is layer 3 and the documentation says it will make layer 2? Can someone give me any assistance?
First of all, set up like you would a 4400 WLC or 2106. I will attach the link configuration guide here for you.
http://www.Cisco.com/en/us/docs/wireless/controller/4.1/Configuration/Guide/ccfig41.html
Many of the advanced features are disabled on the 526 but you set up substantially the same.
Dennis
-
Cisco ACS and the domain controller
Hello
We are currently using the Cisco ACS 3.2.3.11 solution engine and using a Windows domain as a remote agent controller.
We now have the ACS to 4.1
1. do I need to upgrade the remote agent on the domain controller as well?
2. any computer on the network can be used as a Distribution Server?
3. after an initial backup and upgrade then to 3.3.3.3 I make another backup before the upgrade to 4.1?
You can use any PC in the network as a Distribution Server.
-
Cisco Aironet 2602I need for controller
Hi guys,.
Something fast, I will deploy 6 of these access Points of 2602i to a customer and I would like to know if 6 is already a number which calls for the need for a controller.
What do you recommend? To install all of these APs 6 as just stand-alone units or is it better to use a controller and buy the APs that work with controllers (I think that if you use controllers, then the model number is different than the 2602i?)?
Thanks in advance
Ciscobigcat
All depends on your budget.
If you have the budget, get a 2504. If this isn't the case, then you can always load independent.
One of the greatest benefits if you go with a controller is CleanAir. CleanAir is supported only when you have WLC.
-
RMS Expressway Cisco licenses for B2B calls
Hi Experts,
We have Cisco Expressway Setup for B2B calls. We have 6 licenses RMS across Highway C & E, making 3 on EXP E and 3 on EXP C.
Now, I'm able to do 3 Conference of the party including the host. Myself and 2 other B2B calls for a video conference. Where that we watched for 3 with the exception of the host Party Conference.
We were under the impression that if we buy 3 licenses RMS, we have 4 video party conference. It's 3 outside calls excluding the host.
Can someone explain how the RMS license.
Our IPT put in place:
CUCM 10.5
SX20 - recorded at CUCM
Motorway C - containing 3 licenses RMS
Highway E - containing 3 licenses RMS
Concerning
Benyoucef
Hi, Renaud,.
Licenses RMS are concurrent, so in your case both licenses RMS (one in each Expressway) per call are necessary. You can check the following positions related to similar queries
https://supportforums.Cisco.com/discussion/12444331/Jabber-guest-require...
https://supportforums.Cisco.com/discussion/12522961/RMS-license-Cisco-ex...
https://supportforums.Cisco.com/discussion/12240916/Expressway-LIC-exp-r...
Manish
-Does the rate of useful messages-
-
Addressing non-dimensional single MODEL?
Hi all
Oracle Database 11 g Enterprise Edition Release 11.2.0.3.0 - 64 bit Production
Req:
I have a field with words in double as ' PRESIDENT; THE PRESIDENT OF THE EXECUTIVE; The "(séparés par deles de points-virgules) PRESIDENT, I need to remove duplicates from a line." I like 1 million rows to work on...
First time I use the model Dimension byORA-32638: Non unique addressing in MODEL dimensions 32638. 00000 - "Non unique addressing in MODEL dimensions" *Cause: The address space defined for the MODEL (partition by and dimension by expressions) do not uniquely identify each cell. *Action: Rewrite the MODEL clause. Using UNIQUE SINGLE REFERENCE option might help.
Any approach better to handle this kind of situation other than model Dimension bySELECT BIO, RTRIM (str_new, ';') new_str FROM db_temp MODEL DIMENSION BY (0 dim) MEASURES (BIO, BIO || ';' STR_NEW) RULES ITERATE (1000) UNTIL (STR_NEW[0] = PREVIOUS (STR_NEW[0])) (str_new [0] = REGEXP_REPLACE (str_new[0], '(^|;)([^;]+;)(.*?;)?\2+', '\1\2\3'));
Don't you have a unique ID column in the table?
In this case, all you have to do is to add a PARTITION clause:
... MODEL PARTITION BY (id) DIMENSION BY (0 dim) ...
If you do not have this column, you can also calculate an on-the-fly:
... MODEL PARTITION BY (rownum rn) DIMENSION BY (0 dim) ...
Maybe you are looking for
-
Pavilion dm1 4125sz: "Speakers unplugged" after 10 Winows upgrade
I upgraded from Windows 7 to Windows 10 weeks ago. This seems successful, and I have not used the phone so far. I find that I have no audio output. The "speaker" icon has a red x at the bottom, and when I move the mouse over it, he said: "no speake
-
How can I go back to the previous version of Firefox to version 4, which is horrible?
I liked the previous version of Firefox. Since I downloaded Firefox 4, my Norton is not compatible, my google toolbar has disappeared and I can't even insert a URL in new tabs. How can I go back to the previous version of Firefox?
-
A Firefox help page appears for a while and is then wiped away, in FF4RC
I go to the Firefox Help Page "Look at a video in Firefox without a plugin", and the content of the body appears for a few moments (on my Vista laptop) and then disappears, leaving only the title, the line of contributors, a block of white space, the
-
Account reset virtual store - account 31187
Hello, please make my Toshiba e-store account. need a staff account note reset for 31187 after update to E_1.1.00 but I have only a blank screen of white. Mentions legal 70.jt1.c thing or the agood etc.
-
Satellite A135 does not recognize the new drive to CD/DVD UJ - 850
I replace my dvd Panasonic UJ-850 drive, and I can't seem to recognize. Is there some soldering or settings I have to do.If I update to UJ-870, I should do the same thing?