Initializing connection to Tungsten E2 of UWK

Similar Questions

• Horizon view 7, Windows 10, Apex 2800, results of initial connection to the single monitor, later work very well

  Hey guys, this is the configuration.

  View of the horizon 7.0.0

  ESXi 6.0 build 3620759 (U2)

  Apex 2800 and driver package 2.5.3 (supports for Windows 10 and vSphere 6)

  Windows 10 x 64

  VMware Tools 10.0.8

  The symptom is on the initial connection, the second monitor is not same display and the primaries to the resolution no standard. Try to whittle down where it is. PCoIP server log shows that APEX is only used for one of the monitors, which is not good. Later connections show using Apex for two. Apex driver is installed in the Windows 10 comments as well as ESXi. Think it is purely a question of Teradici, but thought I'd post here in case someone else has experienced.

  Initials

  

  Subsequent

  

  I was able to work around the problem by making a pool out of the gold statue and by connecting to it with a zero client, by disconnecting and then reconnecting in. Then I built the pool out of this statue in gold which had already been connected with a zero client. For good measure, I also reinstalled the drivers of the Apex in the gold statue.

• Security server to slow Server Broker on the initial connection

  I'll open a ticket support as well but thought I would ask here.

  My network team assures me that all configurations are as they should be, and I tend to believe them.

  The problem is that after so many hours, if anyone has used the Security Server, the initial connection to a desktop computer may take up to 10 minutes.  There is an initial delay before the user is prompted credentials, then another delay before they are invited to choose their virtual machine.  Once they are connected, everything works fine.  Are they disconnect and reconnect immediately to the whole process takes 10 seconds.

  Our tracks seem to indicate that the Security Server tries to reuse an old connection through the firewall on the servers of broker.  He waits for this timeout and then establishes a new connection to how the process is accelerating.

  Can anyone provide any idea for this?

  I have experienced this same problem and opened a ticket, 1116381631, in case you want to reference it. The reasoning of that problem directly from VMware

  ' Nervous newspapers and e show the cause of the problem. " The fundamental issue is that common AJP connections that are used by the Security server to communicate with the broker for connections are closed on the network (not by the server security VDM or broker) If you are planning a period of time. »

  They had a fix available for VDM 2.1 and allegedly solved the problem in 3.01. I am currently on 3.01 and I have not seen the problem for some time. I hope this helps.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Screen on window 10 flashing with facial recognition initial connection Logo. (I can not connect)

  Hello

  I just bought a new Dell laptop with window 10.  The initial screen is flashing with facial recognition of Dell. I can not connect to the PC.

  Please any solution to this problem.

  Thank you

  Jesus

  Thanks, but how DO you start in safe mode? Can you send a link or something? All the videos on youtube that I find only to explain how to do it with the button "restart" that I can not click on. Thank you very much for the help! :)

• How can I change the initial connection speed in the State of the connection to the Local network?

  Default value is always 100.0 Mbps.  I need to account for 3-5 Mbps for the chart on the scale correctly in task mgr.

  Salvation of yesteryear,

  I suggest you have a look at the following link:

  Local area connection status does not show the correct speed

  I hope this helps.

• Initial connection of blackBerry Smartphones to the PC to BB desktop software

  First of all, I am the village * beep *.  I had a BB 8700 for awhile and after my failedto download the BB desktop PC crash and failed to back up my phone.

  I downloaded the PC to BB desktop software and the software recognized my phone was connected (even gave my BB PIN code).  Everything worked without problems until I was asked for my password.  I tried my password for my phone and which was not accepted.  I tried a few other variations without result.

  I have no backup file, nothing to indicate that the password is / was.  This doesn't seem to be a "simple" problem  A person must enter into the database of RIM to reset my password, give me a temporary and then allow me to enter a new permanent password.

  Who should I call RIM to fix this?

  Hi there - I realize that it's been 2 weeks and I hope that it is already resolved, but this requires clarification.

  There is no password that anyone can give you to solve this problem. The password to enter the PC is the correct password that you use your BB is blocked from password. But the trick is to know what is the password.

  Most of the time, the configuration of the BB keyboard, you may think that you are entering in some characters, but in reality you are before anything else. The use of the alt, ctrl, caps, sym or other control keys affect the actual characters resulting which are sent by your BB. You must know exactly these characters rather than just the BB keyboard keys you press... and reproduce exactly the characters when you type your password on your PC keyboard.

  Good luck!

• Printer prints not portable, initially connected, test page printed successfully

  Laptop wireless connected via router.  Printing software installed on the laptop.  Additional added to the list of devices of laptop computer.  Printer installed on the desktop computer.  Laptop not found during the search for additional devices.  Printer appears in the list of portable and desktop devices.  Hard printer connected to the router.  Laptop using Windows 8, desktop using Windows 7.

  Hello

  I suggest to follow the steps provided and check if it helps.

  For Windows 7: Solve printer problems: http://windows.microsoft.com/en-in/windows/printer-problems-in-windows-help#fix-printer-problems=windows-7&v1h=win8tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1

  Connect to Bluetooth and other wireless or network devices: http://windows.microsoft.com/en-in/windows7/connect-to-bluetooth-and-other-wireless-or-network-devices

  Add a device or computer to a network: http://windows.microsoft.com/en-in/windows7/add-a-device-or-computer-to-a-network

  Share a printer: http://windows.microsoft.com/en-in/windows7/share-a-printer

  Computer for Windows 8: How to troubleshoot printing problems in Windows: http://windows.microsoft.com/en-in/windows-8/how-to-solve-printing-problems

  Why Windows is not find my device: http://windows.microsoft.com/en-in/windows-8/why-isn ' t-windows-conclusion-device

  Add a device or a PC to a network: http://windows.microsoft.com/en-in/windows-8/add-device-or-pc-to-network

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• Slow initial connection using Cisco VPN Client

  I am currently using Cisco VPN Client v5.0.07.0290.  Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully.  I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">

  Hi Sergio,

  You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.

  Thank you

  Delvallée

• Extraction of SSL with initial Connect-VIServer

  Sorry if this has already been asked before, but I was not able to find it by searching online or in the forums.

  When you start a connection to another host of VC/ESXi, there is some information about x 509 certificate as shown below.

  * The X 509 chain could not be achieved with the root certificate.

  Certificate: [subject]

  C = US, CN = vcenter60 - 4.primp - industries.com

  [Issuer]

  O = vcenter60 - 4.primp - industries.com, C = US, DC = local, DC = vghetto, CN = CA

  [Number]

  00D9B9AE28CFD6CF4D

  [Not before]

  02/08/2015-09:19:14

  [Not After]

  02/02/2025 09:19:13

  [Imprint]

  B846B9F36C1D978CEDA0199294E61B4515656396

  I would like to enter the thumbprint SSL "B846B9F36C1D978CEDA0199294E61B4515656396"? I looked online and even asked some people but never able to retrieve this property by using PowerShell/PowerCLI. I can do it easily on one other system Windows with openssl (http://www.virtuallyghetto.com/2012/04/extracting-ssl-thumbprint-from-esxi.html), but wanted to see if there is a way without going through relays on the external packaging and since it is available as part of the connect-VIServer, I thought it must be possible but my PowerCLI-Fu isn't quite at the height as the others , figure so I ask. If it is indeed removable, which I guess it is then a bonus would be to format and so I have a variable that looks like: B8:46:B9:F3:6 C: 1 d: 97:8 C: ED: A0:19:92:94:E6:1 B: 45:15:65:63:96

  
  

  Luc Merci in advance
  

  Function Test-WebServerSSL {
  # Function original location: http://en-us.sysadmins.lv/Lists/Posts/Post.aspx?List=332991f0-bfed-4143-9eea-f521167d287c&ID=60
  [CmdletBinding()]
      param(
          [Parameter(Mandatory = $true, ValueFromPipeline = $true, Position = 0)]
          [string]$URL,
          [Parameter(Position = 1)]
          [ValidateRange(1,65535)]
          [int]$Port = 443,
          [Parameter(Position = 2)]
          [Net.WebProxy]$Proxy,
          [Parameter(Position = 3)]
          [int]$Timeout = 15000,
          [switch]$UseUserContext
      )
  Add-Type @"
  using System;
  using System.Net;
  using System.Security.Cryptography.X509Certificates;
  namespace PKI {
      namespace Web {
          public class WebSSL {
              public Uri OriginalURi;
              public Uri ReturnedURi;
              public X509Certificate2 Certificate;
              //public X500DistinguishedName Issuer;
              //public X500DistinguishedName Subject;
              public string Issuer;
              public string Subject;
              public string[] SubjectAlternativeNames;
              public bool CertificateIsValid;
              //public X509ChainStatus[] ErrorInformation;
              public string[] ErrorInformation;
              public HttpWebResponse Response;
          }
      }
  }
  "@
      $ConnectString = "https://$url`:$port"
      $WebRequest = [Net.WebRequest]::Create($ConnectString)
      $WebRequest.Proxy = $Proxy
      $WebRequest.Credentials = $null
      $WebRequest.Timeout = $Timeout
      $WebRequest.AllowAutoRedirect = $true
      [Net.ServicePointManager]::ServerCertificateValidationCallback = {$true}
      try {$Response = $WebRequest.GetResponse()}
      catch {}
      if ($WebRequest.ServicePoint.Certificate -ne $null) {
          $Cert = [Security.Cryptography.X509Certificates.X509Certificate2]$WebRequest.ServicePoint.Certificate.Handle
          try {$SAN = ($Cert.Extensions | Where-Object {$_.Oid.Value -eq "2.5.29.17"}).Format(0) -split ", "}
          catch {$SAN = $null}
          $chain = New-Object Security.Cryptography.X509Certificates.X509Chain -ArgumentList (!$UseUserContext)
          [void]$chain.ChainPolicy.ApplicationPolicy.Add("1.3.6.1.5.5.7.3.1")
          $Status = $chain.Build($Cert)
          New-Object PKI.Web.WebSSL -Property @{
              OriginalUri = $ConnectString;
              ReturnedUri = $Response.ResponseUri;
              Certificate = $WebRequest.ServicePoint.Certificate;
              Issuer = $WebRequest.ServicePoint.Certificate.Issuer;
              Subject = $WebRequest.ServicePoint.Certificate.Subject;
              SubjectAlternativeNames = $SAN;
              CertificateIsValid = $Status;
              Response = $Response;
              ErrorInformation = $chain.ChainStatus | ForEach-Object {$_.Status}
          }
          $chain.Reset()
          [Net.ServicePointManager]::ServerCertificateValidationCallback = $null
      } else {
          Write-Error $Error[0]
      }
  }
  
  $cert = Test-WebServerSSL MYVC
  $cert.Certificate.Thumbprint
  

• The headset audio USB deforms after initially connect xbox 360 controller for windows

  Hello world.

  It seems that many people (including me, now) start meeting audio distortion after they plug a Xbox 360 controller for windows on their computer for the first time. I have a headset Audio USB of Dynex Mono, and whenever I try to use the microphone, the sound comes out distorted. Also, when I try to use the earphone to listen to whatever it is that the audio is also flawed.

  Did anyone here know what I can do, so I can get the controller and the helmet the two working together in a computer? The headset works fine in another computer.

  I have Windows XP Home SP3.

  writing in the new message: * e-mail address is removed from the privacy... *

  Hello world.

  It seems that many people (including me, now) start meeting audio distortion after they plug a Xbox 360 controller for windows on their computer for the first time. I have a headset Audio USB of Dynex Mono, and whenever I try to use the microphone, the sound comes out distorted. Also, when I try to use the earphone to listen to whatever it is that the audio is also flawed.

  Did anyone here know what I can do, so I can get the controller and the helmet the two working together in a computer? The headset works fine in another computer.

  I have Windows XP Home SP3.

  The Xbox controller draw right on the edge for a USB port, putting pressure on all of the USB bus, especially if there are other USB devices. If you get an external USB powered hub to add to your system and plug the controller, you will solve your problem.

  I had the same problem with my Creative Labs USB sound card and the Xbox controller at the same time. I picked up a Zonet similar to this (different brand):

  http://www.Newegg.com/product/product.aspx?item=N82E16817182168

  I plug my controller, keyboard, and mouse dongle in the hub and plug my sound card directly into one of the ports on the back of the PC. Problem solved! I got no sound since problem.

  SC Tom
  -There is no such thing as TMI if you request technical support.

• Contacts, not able to connect to Office 365

  Hi all

  Suddenly, I have a problem connecting OSX Contacts to Office 365/Exchange contacts. They certainly were able to load at some point, but recently started error (not sure if it was after an OSX update or a 365 tenant who is behind the scenes).

  After an initial connection attempt,-error comes in contact with a "!" and the error message "the operation could not be completed. (SOAPWebServicesErrorDomain error-997). "I ran this test on several customer El Capitan (all v.10.11.3), local accounts OSX different profile 'clean', using several 365 accounts in our environment, all the errors the same way. Interestingly, when I run a powershell command to purge all contacts from all mailboxes on the Exchange, contacts OSX will connect then, but once a contact is added (via either OWA or Outlook contacts OSX) the "!" will appear again with the same error message above. I tried this solution that has worked for many encounter the same problem, but without success for us. Here is the output of the system of the connection attempt/failure log. Any help would be appreciated!

  [Mar 7 19:38:50 MBPCLIENT1 loginwindow [105]:-[SFLListManager(ServiceReplyProtocol) notifyChanges:toListWithIdentifier:] notified of changes of the list element with the identifier com.apple.LSSharedFileList.RecentApplications

  Mar 7 19:38:50 MBPCLIENT1 sandboxd [6645] ([7139]): Contacts (7139) allow com.apple.AddressBook.AddressBookApplicationFrameworkIPC mach-register

  Mar 7 19:38:50 MBPCLIENT1 useractivityd [289]:-[UAUserActivityClientProcess doUpdateUserActivityInfo:makeCurrent:completionHandler:], refusing to record the activity of the user of the client and return error Domain = UAContinuityErrorDomain Code =-108 "(null)" for the element < __NSConcreteUUID 0x7f8031e166c0 > 1592357C-3BCD-49CE-9BBE-4FDB89C27C48 com.apple.Contacts.ViewingCard (UAUserActivityClientProcess.m #1766)

  Mar 7 19:38:53 MBPCLIENT1 Contacts [7139]:-[Analyzer SOAPParser:0x7fc3e354e730: didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in EWSContactItemType for ConversationGuid (t:ConversationGuid)

  Mar 7 19:38:53 MBPCLIENT1 Contacts [7139]:-[Analyzer SOAPParser:0x7fc3e59a16f0: didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in EWSContactItemType for ConversationGuid (t:ConversationGuid)

  Mar 7 19:38:54 MBPCLIENT1 Contacts [7139]:-[Analyzer SOAPParser:0x7fc3e5a359b0: didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in EWSContactItemType for ConversationGuid (t:ConversationGuid)

  Mar 7 19:38:55 MBPCLIENT1 Contacts [7139]:-[Analyzer SOAPParser:0x7fc3e367f5c0: didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in EWSContactItemType for ConversationGuid (t:ConversationGuid)

  I also had the same problem, with also try this solution as well.

  With the help of Office 365 with the latest version of 15 Outlook for mac.  This also happens on multiple machines, so I don't think it's a communication with Contacts on OSX 10.11.3 and Office 365.

• Palm Tungsten E2 Bluetooth just to ICS on Windows 7 Home Premium 64 bit

  Connecting Palm Tungsten E2 (TE2) via Bluetooth for ICS (Internet Connection Sharing) on Windows 7 Home Premium 64-bit.  No other requiered just internet activity, the two are paired, I can see TE2 on Win and Win tour on TE2, TE2 just can't connect with the tour, I got 2 messages according to the network, I try, so I think that I must correct the type of network, any suggestion?

  In the Tower, no palm software installed as I Don t Sync to any doc, the order of the day,...  Just interested in ICS.

  Hello and welcome to the HP support community!

  You will most likely need an application called Softick PPP:

  http://www.Softick.com/PPP/

  WyreNut

• Unable to connect after the most recent firmware for Microsoft Surface Pro 3 update

  Hi, I upgraded my Surface Pro to Windows 10 2... had no problems connecting to R7000 on band 5G. After upgrade the R7000 firmware to the latest version (V1.0.4.30_1.1.67), I now have problems connecting on the band of 5 G. Tablet must be adjacent to the router to connect on 5G band however once connected is connection is kept at distance (about 50 feet). However if I choose the 2.4GH I have no problem in establishing the initial connection to a distance of band. Did someone else has this problem and is there a solution?

  Thank you!

  Thanks a bunch, I went through all the processes of 'Factory Reset' and which certainly did not help. I took your advice and your instructions on return to 1.0.4.28 and it worked like a charm!

  I am now my Surface automatically compressed to a distance of 50 feet or more, through 3 walls on my terrace (as far as I dared so far) no problemo!

  With the latest firmware, I had to be sitting next to the router. The latest firmware is really baaad!

  Thank sagain for your help!

• OK to mix 'of connection to the switch"and"close relay switch?

  Hi all

  I'm developing a test sequence using the card multiplexer 2527 to the track signals.  To configure the card, I use DAQmx switch functions.  In my application, I have a Subvi routine that imports the data from a spreadsheet Setup and run a loop for to set the configuration for each step (each iteration of the loop contains the channel for 2527 card information).  The topology is set on the first iteration, as well as the configuration of the path to the first string.

  My concern is this: I need to close the extra channels/relays without changing the topology or resetting the device.  In the first round, I use "connection to the switch" function to set the initial path, (ch0 to com0 for example).  Then in subsequent iterations of the loop, I use "Relay close switch" function to close the additional channels individually (for example k2).  In the end, when the measure is taken, both ch0 ch2 must be closed and routed to com0.  This implementation is so sure, or am I somehow to make the adjustments to the initial loop?

  I would like to test this with the hardware, but it is not yet available.

  Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer.

  Please notify.  Thank you.

  GSinMN

  Hello GSinMN,

  It's OK to mix 'of connection to the switch"and"Close relay switch"If you understand what's happening below. "Switch Connect" connects two channels by closing a path of relay between the channels, then "Close relay switch" can be used to change the State of the individual relays. If you are not careful you can mess up your connection by activating / deactivating relays that are part of the route connecting your channels.

  "Also, I realize that I could use independent topology and configure all relays individually for each step, but I hope that my approach will be easier and safer."

  I would recommend the topology independent if you want to stick with connections to channels only. http://zone.NI.com/reference/en-XX/help/375472G-01/switch/2527_independent/

  Initial connection:

  CH0-> pcom0

  pcom0plus-> icom0plus

  pcom0minus-> icom0minus

  icom0-> com0

  In each future iteration just connect to the next to pcom0 channel (which will be indirectly connect it to com0):

  CH1-> pcom0

  CH2-> pcom0

  ...

  ...

  Jarrod

• Unable to connect to targets PXI - 8196 RT in MAX

  I'm trying to set up the initial connection to my goal of RT (it is a model used, configured by an engineer OR running LabVIEW RT front arrived at our laboratory), but did not have much success.  I have connected the target RT, a PXI-8196, directly on my Windows computer using an Ethernet cable and manually set an IP address for this connection in Windows Network & Sharing Center.  When I try to connect to the target of RT in NOR-MAX, I do the following:--> create a new--> remote device (not on the local subnet) enter the IP address I specified manually.  When I type "Finish", however, I get the following error message: "failed to initialize the remote connection or targets.

  I have disabled the Windows Firewall on the Ethernet port and also downloaded and re-installed PXI Platform Services.  Is there a step I'm missing, or anyone any suggestions of what else to try?

  I use NI MAX version 5.6, Windows 8 running on the host computer and the on-board computer is a PXI-8196.  Thanks in advance!

  I just went through this with another PXI controller.  Absolutely, you don't want the PXI to reach a binding address local 169.254.x.x, because this will allow you to force MAX to connect.

  Start by setting is using your PXI controller upwards with a monitor, so you can see what is happening, and that it address and a keyboard, if you need to enter the BIOS of the controller.

  On your PC, connect an Ethernet cable from the NETWORK adapter that you use for communication PXI for PXI.

  Assuming that your PXI has a 169.254.x.x address, configure your NETWORK card to also have a similar (but different) address, by using a subnet mask of 255.255.0.0 (so the 169,254 pieces must match, but the other two numbers is not guaranteed).

  Now open MAX.  Click on remote systems.  I guess you don't show anything there, and the right pane is empty.  In the right pane, click on «Create a new...» "and select"remote device (not on the local subnet).  Yes, it is on the local subnet, but never mind.  When it prompts you for the IP, put the IP address that the PXI monitor shows like PXI IP.  He must find the controller almost instantly.

  What I'd do next is to configure the IP address that you want to use.  In my case, I use addresses from 10.0.x.x for both my network cards that "speaks" my PXI and PXI.  While MAX talk to your PXI, you can set the IP address, and then restart the PXI - you should see it happen to the new IP address you specified.  Of course, if you change its IP address to a 10.0.x.x address, you will need to change your NETWORK card to also use an address in this range.  Once both have been reset, MAX should be able to find the PXI under remote systems.

  Now, all you have to do is add/remove software and you should be good-to-go.

  Bob Schor