Inline WAN Opt or AV device

Similar Questions

• Defective unit. Miniport (Network Monitor) Wan #2 (Code 31)

  Defective unit. Miniport (Network Monitor) Wan #2 (Code 31) win 8, S855D from Toshiba. Failed to uninstall the device or load drivers.

  No errors on the first instance of Miniport Wan (Network Monitor)
  Problem started after 1 t Western Digital drive backup (passport). I scraped the WD Installer and restored to pre install passport.
  Miniport (Network Monitor) Wan #2 disappeared, no device in Device Manager.
  Win 8 update showed 5 important files identified by download. Installed files, (passport No.) original device error is back.
  Tried to "Regedit", access denied with admin log in. Error has nothing to do with a network card, despite its location in the Device Manager. Everything works, I want to just #2 GONE! Answers to similar questions have not given favourable results, so I digress and must request a similar, yet pending issue. Any help is appreciated.
  After several years of gene, this solves the problem for me:

  http://support.Microsoft.com/kb/2871372

  Even had an explanation :D

• Error 0xBFF6001F when trying to Max NI image acquisition

  Hello, before you start I want to say that I have read the previous discussions on this error code and tried the solutions, but none have worked.

  I installed SP1 of Labview 2015 and 2016 are going TO and have a grey Point flea 3 CCD (FL3-FW-03S3M) connected to my computer.

  Looking at the camera with the fly capture software I can get pictures but when I use NI Max I get error 0xBFF6001F. Any ideas on how to get the camera work?

  Also my device manager:

  

  Looks like you have an analog card (PCI-1411), you buy from in the first image. I guess nothing is connected to it and that is where the error is coming from.

  Image of Device Manager, it seems that you have installed Point Grey host bus driver. This will prevent IMAQdx to see the camera, let alone to benefit from its pilot link. You must use the Grey top driver utility of switching first opt for your device from the host bus drivers native to the operating system, then you want to change the camera to associate with the driver IMAQdx instead of Point Grey.

• Between the 2 separate companies sharing router

  I'm helping someone to share a router between the 2 separate companies.  They have a linksys E2500 and 2 companies (their own and the neighbouring company) the two connection, either wired or wireless, to the same router.

  They were not aware that this meant guys next had access to computers in their network / and now are asking if there is a way to separate the 2.  So to share the Internet, but limit each group to only have access to their own computer.

  Now, I knew that the current configuration was wrong, but would need advice on what needs to be done at this stage to ensure that each group.  You can create a group for each and be fixed?

  Thank you.

  Low-cost solutions:

  1)

  • If the ISP has provided a modem which has capabililes built routing in and multiple LAN ports. Then use the device as the main router ISP and if it has wireless disable.
  • Install the E2500 in one place and connect its WAN port to the device of the ISP.
  • Install another router cheap wireless in the other location linking its WAN port to the device of the ISP.
  • Make sure all firewalls are enabled.

  2)

  • Buy two inexpensive routers.
  • Keep your E2500 is the main router and disable it is wireless.
  • Install inexpensive routers at each location linking their WAN for the E2500 ports.
  • Make sure all firewalls are enabled.

  The reason that you can not do with the E2500 without additional hardware, it is that it's wireless cannot be configured for the RLV or with insulation wireless. Basically any device connected to the wireless access to any other device wireless and theres no way to change this behavior, I know.

• WAG320n to WRT610n connection helps WET610n bridge ethernet

  I have upgraded my network with a modem/router WAG320n and have a (ethernet bridge) WET610n in my room remotely.  Because the WET is just a single port, I would like to connect my old WRT610n router to bridge, but need to know the right settings and connection information.  The goal is to use wireless in the remote location and additional ports.

  Problem solved and improved

  Thanks Klatch,

  The WAG320n is nice, but not simultaneous dual band, so I put the 5 GHz.  I wired hard (WAP610n) one point of access to the router, set it to 2. 4 Ghz and placed about 3 meters outside the router.  This gave me access to the second floor for all devices with two bands.  (I have given it's own SSID to distinguish it from the access point).

  To extend coverage to the first floor, I installed Ethernet bridge Wireless N (WET610N) on the beach at the fringe of my output of routers (still 4 bars).  The bridge is set to 5 GHz - because what is the WAG320.  Then I connected the router WRT610N (which is simultaneous dual band) to the bridge.  You plug the bridge into a LAN on the WRT610N, NOT the WAN port port.  The WRT610 has been programmed to 192.168.1.2, disabled DHCP, NAT disabled.  I have 3 other hard WAN ports connected to devices (Playstation, Slingbox, Blue Ray player).  All other PC first floor is connected wirelessly via the 2.4 GHZ or 5 GHz bands.  The coverage of the first floor is excellent.   I held the different SSID for each router and Access Point, to distinguish which router or the band I want to connect to.

  If linksys has been only the simultaneous dual-band of WAG320, it would provide the extension of coverage to all old and new features!    Everyone is not wrapped around 5 GHz yet!  Then.  If you want to extend and use another router as Repeater (wireless), you need an Ethernet Bridge (or wireless game adapter) to the main router and connect to the secondary router.   Everything can be done with a little effort.  Thank you

• WDM5: Error when you try to push our HAgent update

  I get an error when I try to get a WES7HAgentUpgrade for a terminal:

  Try 1:XC Failed: 1. [error: could not retrieve the list of all files and the master repository directory.] [WebDAV error: failed to get the tree of directories of the remote computer.] [HTTP response code: 404: 404 error Code] line no.: 20 Cmd:XC WES7HAgentUpgrade\Temp\ * C:\Temp\

  Details of the system in question:

  Any new installation of WDM 5.0 on Windows Server 2008 (also new installation).

  Client terminal is a thin Client C90LE7, version 9.03 (build 0827.4096), run WES7 version 6.01 (7601) SP1. I flashed recently the image to build 0827 via USB - it wouldn't connect to the WDM server until I did this. The C90LE7 unit is listed in the list of WDM device manager.

  I want to update the C90LE7 HAgent to the 6.3.2.54 version that came with WDM 5.0. The currently installed version of HAgent is 6.0.0.45.

  Things I've tried:

  -I can go to the localhost/.../Rapport directory and browse directories and not files - no problem.

  -J' ran the report of diagnosis devices and everythign Manager came in GREEN with the exception of the following:
  * FAIL: C:\Program Files (x86)\Wyse\WDM\Utilities\Database\DatabaseCredentialManager.exe (5.0.0.707) - there is no.)
  * FAIL: C:\Program Files (x86)\Wyse\WDM\Utilities\Database\HAConfigureUtility.exe (5.0.0.707) - there is no.)
  * FAIL: C:\Program Files (x86)\Wyse\WDM\Utilities\GUIExtractor\MgmtConsoleExtract.exe (5.0.0.707) - there is no.)

  Any ideas or suggestions? I got lost.

  For what it's worth, the error indicates a failure of connection SWREP.  With the system running Hagent 6.0.0.45 gen1 I suspect there is a conflict with the support of HTTPS on your SWREP or the use of authentication windows (new support included in the new hagents).

  Test validation in the GUI of WDM > Cfg Mgr > SWREP > MASTER > test connection

  Fail - then package deployment will fail too.  Check if the user pwd has expired (common cause).

  Swing in IIS on this server even one under the MyWDM site confirm WebDAV is enabled.  Check authentication and to test disable them everything except BASIC authentication.  We can change this back later if you wish.  Disable requiring SSL.

  In the properties SWREP > HTTP > uncheck HTTPS/Secure

  test the connection

  Try your update.

  Also, SWREP is accessible in the case growing WAN or DMZ managed devices - make sure that IP address or NAME defined for the location in the properties.  If the devices to do an external name/IP to access WDM you'll want to get in instead of the local IP address, the default then install it.

  k

• Cisco JOINT and IPS hardware bypass

  Hi all

  I have a question about the Cisco JOINT, ASA - AIP - SSM (IPS) and material of the IPS 4200 bypass unit series. Please let me know if the material fails in both cases how to cross traffic. Is there any circumvention of integrated equipment built in the same

  Concerning

  Ankur

  Sorry for the late reply. I've been on vacation for a week.

  ByPass hardware is not available for the JOINT-2 no matter if you use inline vlan pairs or couples inline interface.

  For devices need special interface cards or a hardware bypass switch separate, and none of them are available on the JOINT-2.

  You must configure your network so that there is a second way around the JOINT 2 JOINT-2 failure.

  This can be done with a standard network cable.

  Suppose you have your JOINT-2 configured for inline vlan VLAN 10 matching and 20.

  Configure a standard switchport as an access port on vlan 10.

  Set up an another standard switchport as an access port on vlan 20.

  Now using a standard network cable connect these 2 all switch ports.

  Stop your JOINT-2 and traffic should now be passed through this network cable and your network connectivity must be maintained.

  Bring your JOINT-2 backup, and now spanning tree runs and will choose the JOINT-2 or the network as the main way and the other cable will set in a State of block.

  Run ' show vlan spanning-tree 10 ' and ' show vlan spanning tree 20 "to determine if the cable ports or port JOINT-2 is in a BLK State.»

  If the cable ports are in a State BLK, then you don't need to modify the spanning tree.

  If the JOINT-2 port is in a State BLK, then you need to change the spanning tree cost and/or priority for JOINT-2 port by using the following commands:

  -[No] port-channel channel_number-STP intrusion detection doesn't cost port_cost

  Defines the cost of port tree covering for the data port on the specified module. Without the option restore shipping tree covering for the data port on the module specified in the default value.

  -[not] port-channel channel_number spanning tree priority priority intrusion detection

  Sets the priority of the port spanning tree for the data port on the specified module. Without the option restores the priority of port spanning tree for the data port on the module specified in the default value.

  To learn more about spanning-tree and how these parameters interact with spanning tree you can look through this section of the user guide for the switch or to search cisco.com for documentation of spanning tree:

  http://www.Cisco.com/en/us/partner/docs/switches/LAN/catalyst6500/IOS/12.2Sx/configuration/guide/spantree.html

  NOTE: Your switch must be configured for rapid PVST for failover more rapid. Work with your administrator to switch to determine which spanning tree Protocol is used on your switch. The JOINT-2 does not work with STDS to ensure that STD is not used.

• ISE 1.3 Distributed environment

  Hi all

  in a network with two main campuses and 10 remote with total scheme 3000 offices, to implement Cisco Ise distributed 1.3, we want to buy 2 camera SNS-3415-K9 for synchronization of monitoring/management/policy and 10 VM for node of sevice of strategy, but we found in distributed environment, to a pair of nodes of posture inline, we buy another two device or VM for inline posture?

  Well, it has not been officially said by Cisco, but it's already been removed working on the SNS.3495, so I would say that this isn't something that we should design the new ISE solution with.

  No, the secondary PAN/MNT will handle the same as main Ssnp, you cannot split your PSN between nodes of PAN/MNT.

  "you're telling me that if a remote office fails, lose psn...?

  Don't know what you're asking?

• When is high the NAC

  My team give me a task to impliment of the NAC in a business network solution:

  the solution contains the system wireless using the gamepad wireless LAN, VPN over WAN, reduendancy for each device.

  1. I want to impliment NAC Manager high availability and high server of the NAC Installation Guide, I found a lot of senerios avilabilty

  2. I want to impliment the NAC INband what recommendations server layer 2 or Layer 3 implimentaions

  3. I saw in the installation guide which in high avialabilt of NAC use cabel series and no info about

  Thank you for your help

  Hello

  The best solution for you is to deploy the CCA in a centralized deployment of L3 OOB mode. Local users will be connected to the CAs in L2 OOB.

  In the future, you can easily deploy NAC in the branch offices.

  Looking for your network diagram, you connect CAM and ca to WS-C4509-E switches.

  CAM and CASES use as a null-modem serial cable, you can use it, but it is not necessary if you connected two cams via crossover ethernet cable.

  Kamil,

• Special RV220W NAT allows only a single service?

  Hello

  Just bought a RV220W for a client to replace a WRVS4400N which has no support for individual NAT and stated that the specific NAT for this router is only marginally better.

  I have three WAN addresses and three devices to their card. With the RV0xx, I used the following more than a dozen times.

  WAN 1 address - public address of the router

  Port HTTP, HTTPS and SMTP for Windows Small Business Server 2011

  Messaging and remote Web access are available to the remote.company.com

  Address WAN 2

  One-to-one NAT to Ubuntu Server's private IP address

  Add the following access rules:

  • All refuse
  • Allow everything to the private IP address of the HTTP Server
  • Allow SSH to static IP address of my business to private IP
  • Allow FTP to static IP address of my business to the private IP address

  Companies Web site is accessible to company.com and I can update the site with SSH and FTP

  Address WAN 3

  One-to-one NAT to private IP address of the module of RMM Intel Server Hyper-V (Lights out remote management)

  Add the following access rules:

  • All refuse
  • Allow HTTP, HTTPS, and RMM all ports of statics of my business to the private IP address of RMM modules

  I can access the my business network connection rmm.company.com server

  My problems are:

  1. Specific option NAT requires now allows you to specify the service you want to transfer (Note: service, not services)
  2. If you select all of the service which is the only way that I can see for having more than one service, there is no way to add any specific Allow or Deny rules because the Destination area is dimmed in page access rules.
  3. This results in my Ubuntu Server only have HTTP sent to her and my module RMM having all ports open to any IP address.

  There must be a way around this! I don't understand why the Destination IP option is grayed out for all inbound access rules. I used this same configuration with the RV0xx of Cisco, many Sonicwall, as well as several Cisco ASA firewalls. Obviously this isn't an ASA, but this individual NAT implementation is useless!

  Any help is greatly appreciated. Thank you

  Kevin

  Due to the GUI limiting to one service in individual NAT page, users must go to the firewall > page access rules to specify additional services are allowed.

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• Choose CPU Inline Custom Device

  Hello!

  I wonder if it is possible to assign a Custom inline device to a specific processor. I know it's possible to do a custom asynchronous device.

  I developed a custom device inline, calling an asynchronous vi. I can affect the heart for the asynchronous part, but how to choose the kernel for the part online?

  Thank you...

  Hello, I guess that the online part is executed from the thread VeriStand, then the kernel is involved by the call control loop and cannot be changed. But maybe I'm wrong?

• Error 74 to unflatten string in a device helping custom interface hardware Inline

  Hello

  I am creating a custom device Interface material Inline to communicate on a bus series to Veristand. I want only to communicate via RS232 veristand channel values, I use flatten/unflatten to chain to transfer my data. I choose what it because VISA Write/Read uses strings, and he would always use the same size of string (channels Veristand = 64-bit double-online 8 character string).

  But when it comes to try it with veristand, I have error 74: corrupt memory or data structure. I noticed this error came from the "string unflatten".

  So I plugged in a "clear error" vi just after "unflatten to channel" works, for my custom device runs but gives me wrong results. Then I used the tool NI OF Trace to see what I was writing to the RS232 bus. You can find the result of this. When we take a glance on the viWriteasync functions, we can see that the data written on the bus will already '?... " W.... M' which translates as 0,000232195, although the value that I have passed to the bus was greater than 1.

  I plugged the constant 'false' by 'add array or string of size' 'flatten in string' and 'unflattend to the string' functions.

  Does anyone have an idea what's wrong?

  Kind regards

  Maxim

  Is your session series Visa implemented to put an end to strings with the null character? It's been a while since I worked with serial number, but I remember this could be the case. So then you'd have trouble sending binary data flattened since it would have a lot of characters in it null. Another solution would be to format doubles as text with a specified number of digits of precision, although this will be less accurate and can take more bytes to transfer.

• WAN Miniport device receives error Code 31 in XP

  Problem came to light, when the system would no longer connect to the internet.

  I found that the Miniport network EXTENDED (IPX) device was yellowed out.  I tried to update the drivers using the Windows XP disk.

  You can not remove the device because it indicates that it may be necessary to reboot the system.

  * original title - MiniPort (IPX) Wan gets this error in Device Manager. The device does not work properly because Windows cannot load the drivers required for the device (CODE 31) _ *.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest XP drivers for it > download/install them.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.
  
  See you soon

  Mick Murphy - Microsoft partner

• Device Manager installs... miniport drivers wide area network wan ip, ipv6, network monitor, l2tp, pppoe, pptp.

  Device Manager installs... miniport drivers wide area network wan ip, ipv6, network monitor, l2tp, pppoe, pptp. When it try to install and can not send back me to my manufacturer. but I can't see them dry. Windows Update doesn't see them as missing iether.

  If you've been fiddling with the settings of the bios, betts all are out of service, start with the bios setting to default security failure.

  If you have not been violin, then as it has a new PC to call the manufacturer