Installation of certificate in new ASA

Similar Questions

• New ASA/VPN configuration

  So, I am looking to add one of my spare 5510 firewall to my secondary network as a vpn connection.

  All I want this new ASA to do is handle my site anyconnect VPN connections.  I'm pretty new to ASAs if any help would be great.  I know how to create a new access VPN on my ASA and I added a NAT for my inside and outside traffic to my new Pool of IP VPN.

  My question is, since it's only for the VPN and I want all my current internal traffic to continue to the asa 5510 existing routing, do I have to enter the ACL to my new single AAS of VPN?  ACLs are used for VPN traffic and do I need them to traffic the route via VPN?

  I'll put up inside interface of connection to one of my main Cisco switches and the outside interface connects to my DMZ switch on the new ASA only VPN.

  Thank you

  I don't know if I am how you connect to the external interface of single ASA VPN. Normally, in this type of installation, we would see the ASA VPN "in parallel" with the perimeter firewall.

  You mention the DMZ switch that threw me a little. If you are in France through your main firewall and go to single ASA VPN via the DMZ then Yes you will need to allow several open ports (protocol 50, udp/500, tcp/443 among others) and may have to do some other techniques (NAT - T, etc.) depending on the type of remote you are implementing. That's why we rarely see this configuration used - it adds a good dose of complexity without significant benefit.

  When the old facility is used, you need to switch internal to know to route traffic to the pool VPN through the only ASA VPN inside the interface. A static route is more often used, although you can use OSPF or EIGRP if you wanted to.

  Should generally not be any access list that VPN traffic around the Bank access lists incoming interface. Back to remote clients traffic is coming from inside and out through (and is usually part of anestablished connection) so no access list is necessary inside.

• Migrate certificates on Cisco ASA

  Hello

  I'm migrating an ASA5520 to an ASA5525-x. I'm just going through the configs and copy the bias.

  How can I migrate on certificates?

  Thank you

  If it's a public certificate signed PKI, not easily. You must have the private key of the server (ASA) for use on an another ASA. Unless you checked exportable at creation time, it is not exportable by default.

  You could inform you as to whether the issuer will be re-edited if you submit a new CSR.

• L2l with certificates between 2 ASAs

  Hi all

  I want to set up a VPN L2L/Site-to-site tunnel, which authenticates by using certificates.

  In fact I am following this guide-> http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080aa5be1.shtml

  I configured the tunnel group on both ends, with the trustpoint configured, authenticated and accepted specified.

  I correspondent isakmp policies at both ends, and of course my cryptographic cards contains 3 identical lines - set peer match access-list and transformation-a set cryptomap. Next to those, there are 2 identical lines for life. I haven't specified the trustpoint in encryption card while it is not indicated in the top link (guide) to do, even if I tried, without different result. Debugs him happens exactly the same each time:

  Debug the cry isa 10: (on the remote end)

  TEST-ASA-RA # debug cry isa 10

  TEST-ASA-RA # Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + SA (1) the SELLER (13) + the SELLER (13) + the SELLER (13), SELLER (13) + (0) NONE total length: 208

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, SA payload processing

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Oakley proposal is acceptable

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT-Traversal worm 02 VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, worm received 03 NAT-Traversal, VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT - Traversal RFC VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Fragmentation VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: true

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA payload processing

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build the payloads of ISAKMP security

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, construction of Fragmentation VID + load useful functionality

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 108

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 374

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, processing ke payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ISA_KE

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, nonce payload processing

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, the customer has received Cisco Unity VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received xauth V6 VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment VPN3000 / ASA payload IOS Vendor ID theft (version: 1.0.0 capabilities: 20000001)

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Altiga/Cisco VPN3000/Cisco ASA GW VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building ke payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building nonce payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building certreq payload

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads of Cisco Unity VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, constructing payload V6 VID xauth

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send IOS VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, ASA usurpation IOS Vendor ID payload construction (version: 1.0.0 capabilities: 20000001)

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send Altiga/Cisco VPN3000/Cisco ASA GW VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Generating keys for answering machine...

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 298

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, RRs would fragment a new set of fragmentation. Removal of fragments of old.

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, assembled with success an encrypted pkt of RRs would be fragments!

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + ID (5) + GIS (9) + IOS KEEPALIVE (128) + CERT (6), SELLER (13) + (0) NONE total length: 1987

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ID

  Jul 07 11:36:18 [IKEv1 DECODER]: IP = 80.62.240.136, ID_IPV4_ADDR received ID

  80.62.240.136

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing cert

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment of RSA signature

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, calculation of hash for ISAKMP

  Jul 07 11:36:18 [IKEv1 DECODER]: Dump of Signature received, len 256:

  0000: 8D97FE83 CDA9CEB2 A5D7F63F 0FAA76A4...? ... c.

  0010: 21F229A8 2A714C2D 12F16ABF 08E44664!.). *... qL j... FD

  0020: 0D95A510 0AFFA63B 815CCBB0 B7C708CF...; \......

  0030: 31246316 0E93E084 59395461 118C 9251 $1 c... Y9Ta... Q

  0040: 823A36CB 55F2F59C 3342326D 251F8B7A. : 6.U... 3B2m %... z

  0050: B9C9F916 C403A4D1 59DA3AA8 932312C 0... Y.:.. #..

  0060: 88476460 E9C9A07C 5671C18D A9202382. GD'... | DV... #.

  0070: 441F47AF 74E407B1 DB06B929 406E993D D.G.t...) @n. =

  0080: A7C149FA 1677D1A2 E3105356 4E205E45... I have... w... SVN ^ E

  0090: 06D2CB2A B6BF638E 0910283C 7FF6BAE2... *... c... (<>

  00 to 0: 3F97ADF5 19B 78872 69C0346B 7EF89FAE?... ri.4k... ~

  00B 0: 456E26CF 52CC296B 11F6AE68 2498024C en &. R) k...h$... L

  00C 0: 74658112 you 16121A 68 h

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IOS treatment keep alive payload: proposal = 32767/32767 sec.

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID

  Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, DPD received VID

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, trying to find the group via IKE ID...

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, connection landed on tunnel_group 80.62.240.136

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

  Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, case of mistaken IKE MM Responder WSF (struct & 0xd3dcecf0) , : MM_DONE, EV_ERROR--> EV_COMPARE_IDS--> MM_BLD_MSG6, MM_BLD_MSG6, NullEvent--> MM_BLD_MSG6, EV_VALIDATE_CERT--> MM_BLD_MSG6, EV_UPDATE_CERT--> MM_BLD_MSG6, EV_TEST_CERT--> MM_BLD_MSG6, EV_CHECK_NAT_T, EV_CERT_OK--> MM_BLD_MSG6

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, IKE SA MM:1e531705 ending: 0x0100c002, refcnt flags 0, tuncnt 0

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, sending clear/delete with the message of reason

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, payload of empty hash construction

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, constructing the payload to delete IKE

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, build payloads of hash qm

  Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 5a228b67) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

  Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, Removing peer to peer table does not, no match!

  Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, error: cannot delete PeerTblEntry

  Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

  Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

  Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

  Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

  Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)

  Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68

  Then, it waits a bit and start over. No matter if I am trying to establish the tunnel network or remote endpoint - there is no difference in the result.

  I made a line of debug output "BOLD" - I don't the have not seen this before, don't think that devices Cisco used this alternative area? Thought it was Microsoft?

  1 thing is a reference to the certificates - I use my won Microsoft PKI based on 2003 servers. I have 1 Root CA and 2 subordinates. The root CA is stopped. During the construction of my trustpoints, I start to do my request, give it to one of subordinates, gets my identity certificate and save it on my computer. Then check the chain, which looks always good - RootCA-> SubordinateCA-> ClientCert. Then I extracted the subordinate cert, to authenticate my trustpoint and finally I import the certificate of identity. No complaints, it of all good - and actually working like a charm for my EZVPN configurations.

  So I do not think the problem it's with the certificates, although the release said that there is an incompatibility with the other name in question.

  The debugging online after this statement, I understand not quite - maybe someone can help me with this? Because right after this line, he begins to destroy the tunnel.

  I can provide from configs if necessary, but really, it corresponds to the configuration contained in the guide.

  / Peter

  Can you check the "crypto isakmp identity" command on both sides?  He looks like a side sends the IP, when it expected the certificate DN is the name so it can match the value in the cert.

  Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)

  Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt

  -Jason

• Office 2008 installation fails on the new Macbook Air

  I get a Setup error trying to install Office 2008 on my new MacBook Air running El Capitan.  I tried my new Super drive I bought just to do this, and I also copied the installation on my 750 GB external drive as well, but nothing works?

  Thank you very much

  Craig

  You must install Office 2011, if you can find it, or get a subscription of $99 / year to 2016 from Microsoft Office. Individual applications can be downloaded freely. If you do not have a subscription, then they operate in trial mode.

• Digital installation of certificates with the private key

  I installation of digital certificates in three servers, each of them with Windows Server 2012 R2 Standard but just in one of them, the private key information remain available after installation. The purpose of these servers is to secure the communication with an instance of SQL Server that is installed on each server

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Update KB931125 guard installation root certificate. __

  I installed this update, but it keeps wanting to be installed again & again & again...

  Hello William,.

  you have a WSUS server on your network?

  In my case, there was an identified need and installable old obsolete root certificate update in my WSUS Config.
  When I disable this old "Update" ist, the latest being (from September), installed without a problem on my machines.

  Kind regards
  GoopherNo1

• Windows 7 Installation stuck after installing new graphics card

  Before that, my office is fully compatible with Windows 7, but after that I installed a new graphics (ATI Radeon HD 5450) I can't install Windows 7, when I started to install that everything seems fine, but after it restarted and end Installation it just stuck there!

  Any help?
  I tried to remove the new graphics card and the use of the onboard graphics to install Windows 7 still does not work?
  NOTE: I used Windows XP before installing the new graphics card.
  I'm using Acer Aspire M1800
  CPU: Intel Pentium E6300 processor
  Memory: 2 GB DDR2
  Help appreciated
  -Joey

  Hello Joey

  If right now you go back to Windows XP and the system is slow correct? You have the drivers installed since you went back to XP? If not then click here and select your system. This will bring up a list of available drivers for you. Also, I've included a link below to get the drivers for your new video card. My problem with the question is if your system has enough power to support the video card. Here are the specifications of your card. Check the configuration required for the map and you ensure that you have adequate food. Let me know if it helps. Thank you.

  ATI Radeon HD 5450 Windows XP Drivers

• Windows Setup could not configure Windows on hardware of this computer Installation error on the new hard drive

  Okay so if please bear with me and be patient.  I'm not tech savvy.  I know enough to be able to remove an old hard drive and put another one, but when there are errors, I don't know what to do.

  Here's the situation.

  I have a Dell Studio XPS with Windows 7 installed.  I started having these notifications that my hard drive could be a failure.  I tried everything that I could find to fix it without having to buy a new HARD drive without success.  The current system has a 1 TB Seagate hard drive.  I installed a memory additional bar thingie right after that I got the computer about 4 years ago.  (If someone tells me how to find the properties of real system, I post them if necessary).  Anyway, I bought a new WD 1 TB black disk hard to install before my old dies and loses all my photos and documents, etc...

  I took the old drive yesterday and installed the new hard drive.  I put back the case and turned on the machine.  I put in my Windows 7 installation disc.  He began installing Windows 7... It's completely past the initial screen where it says it to load it and the other... I had accepted the license agreement, but did not have to make a profile and do the work and the reader.  I hope all this makes sense.  Then it pops up this message "installing Windows could not set up Windows on hardware on this computer."  I couldn't figure out what to do from there.  I got the new drive and put the old one back to and here I am. I tried to find solutions to this problem, but I either don't can't make heads or tails out of the responses on the internet or the solution is not exactly my problem.

  Please help if you can!  And if you have any suggestions, please dumb them down so I can understand what to do.  I CAN do if loaded, you just have to not talk too irritable.  Laughing out loud

  Thank you in advance!

  Maybe not...

  The Windows installation is not happy about something, and since it gets at least started which is a good thing, but your installation problem can not really be with Windows - perhaps something about Dell hardware or your 1 TB HARD drive.

  I looked at your system and found this article that you can read to see if it sounds like your original question:

  Windows Setup could not configure Windows on hardware on this computer.

  http://www.Dell.com/support/article/us/en/19/SLN293812/en

  Since Dell has written an article for help on this subject, it means they've met enough times to take the time to compose the article and put it on their WWW site (but, they say, it is a possible resolution).

  Could you take the issue in the Dell online community where experts hang out (especially your amber light).

  Another good place for support is www.bleepingcomputer.com where there is a similar topic as your question (except Vista) on a Dell and a new disk of 1 TB (also a Seagate) and Dell ideas did not work, but someone else has found a way to fix it:

  http://www.bleepingcomputer.com/forums/t/453378/installation-fails-to-complete-on-new-HDD/

  The bleepingcomputer for your error message search reveals other areas and people who have got things to work in different ways, then it is perhaps another place to look for ideas.

  If the installation still fails it would not hurt to do the BIOS setting and see if things are getting longer, and since you are going to write the current settings before proceeding with the adjustment you can always cancel the adjustment if things get worse.

• Installation of firepower on redundant ASA 5512 x pair

  Hi, I am trying to install the firepower on pair redundant asa5512x that is configured in active / standby. These asas have an IPS module installed. I need to remove the old IPS module and install the module of firepower.

  I know I need to stop existing ips module, uninstall it, then load the image to start fire etc... However, I have no experience working with redundant units so I don't know how to install firepower in a configuration of active / standby.

  I tried instructions guides on how to do this upgrade of ips in a redundant pair of asa, but the only guides I've found so far speak upgrade firepower in unit asa autonomous.

  any suggestions, instructions or links to blog/sites that provide instructions step by step on the upgrade of firepower in active/standby mode would be much appreciated.

  Thanks in advance.

  I understand say you that uninstalling ips module cause failover? This should be ok because ASA 9.2.x and earlier the pair HA monitors the State of default service module and which cannot be disabled.

  9.3 ASA presented

  (no) monitor-interface service-module

  .. what allows to disable this behavior. Even on 9.2.x, however, you should be able to uninstall on the rescue unit. When you say that it didn't work, this error message do you have? Is about, I would say: 1. Uninstall secondary ips - standby. Primary-active should see module go down and score watch is not ready. 2. repeat on active primary. When the primary unit active reload, the secondary-sleep should see no assets to mate and the active role. You should now have this situation of active secondary and primary-secondary 3. Install sfr on primary-secondary. Load the boot image, perform the initial configuration module and load running image. 4. install sfr on secondary assets, including the loading and installation stages. When primary-secondary sees reloading secondary-active, it must assume the active State and be primary active. After charging high school-watch it requires correspondence module type (IE both have installed SFR). 5. Save and check the connection to the management center of FireSIGHT on two modules of sfr. 6. create and deploy strategies to the modules in the two ASAs. 7 change the service policy to redirect traffic to the module of sfr for inspection by the policies deployed on these modules, ASA.

• VPN peers on old ASA, reverse routing as we migrate to the new ASA and new Internet

  Hello

  I'm migrating my old Internet/VPN connection. How can I ensure that even existing VPN are addressed to my old/curreent ASA

  While my default gateway must get out of my new internet link

  Very vague question, given the lack of topology ;/

  In general redistribute you your range of IP addresses downstream pool to the nucleus.

• Installation of CS5 on new PC

  I am trying to install CS5 on a new PC; I have the serial number and downloaded Photoshop_12_1_LS1.7z and Photoshop_12_1_LS1; run the latter and have Adobe CS5.1 on my desktop. run set - up.exe - registered serial number and installation runs at the end when it says program was not installed and takes back me to 'Exit Code 6.

  Advice appreciated.

  Try errors 'Exit Code 6' and ' exit 7 "Code install Adobe CS6, CS5.5, CS5, Premiere Elements and Photoshop Elements .

• Digital installation ID as a new file PKCS #12 on Acrobat 9, Win 7, 64 bit

  Digital ID installation as a new file PKCS #12 on Acrobat 9, 64-bit, Win 7, riquires by typing a password. After appares a window with "Password not identical" and stop digital ID creation

  When you create a new digital signature, you make a new password belonging to this signature. You need to think about it, you can't get it back. And you have two places to type when you create. The two password must be the same.

• CS5 installs fine on the new version of WIN 10 but can not load updates

  After installing CS5, I ran Photoshop, then ran the updates from the help tab. It seemed like all the CS5 updates have been downloaded and then I got an error message saying 'Download problems, installation failed' on almost all the programs. The most important of them is camera raw 6.7

  Someone out there has a solution? I've heard others on this forum of State succeed when they upgraded to W7, rather than a new facility in W10. Certainly I'm not the first to deal with this? No, I don't go to CC. I've spent thousands of $s on Photoshop and Suite products over the years and I would switch to a competitive product that I can buy instead. Fed up!

  Try to install your updates manually

  Beginning of the updates here and product selection, read to see if you need to install updates in the order of the numbers, or if updates are cumulative for the product http://www.adobe.com/downloads/updates/

• View VMware 5.2: Certificate problem new issuance

  Hello

  I was trying to create a new certificate in my lab Vmware view, but without success.

  I got to the following problems:

  ----------------------------------------------

  keytool - genkey - keyalg "RSA" - keystore keys.p12 - pkcs12-validity 360 - storepass xxx stores

  What is the name of your organizational unit? XX

  What is the name of your organization: xxx

  What is the name of your city or locality: xx

  What is the code for this device-two letter country? : xx

  keytool - certreq - keyalg "RSA" - folder - certificate.csr keys.p12 stores - pkcs12 keystore - storepass secret

  Certreq-submit attrib - "certificatetemplate:WebServer" c:\certificate.csr (on the domain controller)

  
  

  Certutil-dspublish - f certificate.cer (on the domain controller)

  
  

  keytool-import - stores - keys.p12 pkcs12 keystore - storepass secret - keyalg 'RSA' - trustcacerts - file certificate.p7b

  
  

  Locked.Properties (file SSLgateway file...)

  keyfile = Keys.P12

  KeyPass = secret

  shops = pkcs12

  ---------------------------------------------

  I tried to import the certificate into the GPO and the display folder.

  Restarted the server, without success.

  In a guide, he mentions that a self-signed certificate VDM is located in the SSLgateway folder on the login server, but I do not have.

  My test clients can connect to several different pool with self-signed certificate warnings.

  What happens here?

  wrong answers to the questions keytool? they are entirely dependent on the appropriate ORGANIZATIONAL unit?

  The web interface for the administration console Vmware View certificate is not working either.

  The steps you are using are correct to view 5.0 and below, from 5.1 view, we went with the Windows certificate store. Follow the new documentation from the outset either import the p12 file you've already created in Windows. The latter can be done by following the steps below:

  1 mmc, open the Certificates snap-in for the local computer account

  2. under Personnel\Certificats, right-click and select Import

  3. Select the .p12 file you created

  4. Enter the required password, make sure that the check box the key is exportable is selected

  5. right click on the new certificate, change its properties, and add the friendly name "vdm".

  6. remove the friendly name of the self-signed certificate generated or remove it completely

  7 delete locked.properties lines you had before

  8 restart the service