Installation of the USB 2.0 extension cable failure, and I am on Windows 7.

Similar Questions

• Server does not start after the installation of the USB bootable, ESXi

  Hello

  I installed VMware ESXi 5 on a SSD drive using a bootable USB key, but my server does not automatically start since the SSD after installation. I can boot ESXi in the offered by the BIOS boot menu.

  The startup configuration is perhaps incorrect because during the installation of the USB drive is present, but after the installation, it is not?

  Also has anyone seen this problem?

  Kind regards

  Gijsbert

  Updating the BIOS on the DQ77MK at 49, and you should be able to start - UEFI must never be activated.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• using a lexar Flash DRIVE to work on excel sheets. I went to open the USB key that ive been using and he said: 'it must be formatted. "

  i; ve been using a Flash DRIVE from lexar to work on excel sheets.  I went to open the USB key that ive been using and he said: "it must be in the format".  I did have to do at this point and that to format ill lose all my docs?  Help

  Try to play on another computer. If she still wants to be shaped, it's game over.

  If it's ok, copy the files on it before doing anything else and you get a new flash drive...

• Downloaded the patch for an extension of game / will not work because windows cannot find ' RTR - patcher.bat

  Downloaded the patch for an extension of game / will not work because windows cannot find ' RTR - patcher.bat

  Original title: rtr - patcher.bat

  Brian

  You need to contact the developer of the game, because they are the only one who can help you.  We support Microsoft software & hardware here.

• Bootcamp errors during the installation of the USB on iMac mid-2011

  I tried to install Windows 8.1 on my iMac for mid-2011. The problem is that my optical drive is not working properly.

  I created a USB bootable via Bootcamp Assistant on my MBPr and have tried my iMac HARD drive partitioning, using OSX disk utility and disk in recovery mode utility. I tried to leave the space as free and formatted as ExFat and fat.

  At the start of the usb drive and try to install on the bootcamp partition, I get the error that it is a MBR and not on a GPT partition.

  In addition, do not know if it's important, but it is a secondary internal drive. My main drive of OSX is an SSD. I have no problem accessing the drive in question under OSX.

  Help please!

  Mac 2011 (and more) have challenges with no DVD installs due to optical drive problems. Changes to the file info.plist Bootcamp to allow creating install USB works only partially because of start-up problems. Only two solutions that work with a high degree of success are

  1. replace the optical drive, or,

  2 http://forums.macrumors.com/threads/install-a-windows-7-partition-on-mac-osx-wit hout-optical-car-or - usb.1836959 / #post... .

  Following two discussions have some installs successfully, but they usually lead to broken drivers or not functional Apple hardware.

  Re: Bootcamp without optical drive

  Re: Activate Bootcamp install USB for OSX 10.9 * ŒUVRES *.

• Portege R100 - question about the installation of the USB port and Windows problems

  Hello

  I just bought a used Portege R100, but I have some problems. Of course the laptop isn't a CD or DVD, player so I tried an external DVD drive, but it did not work. What kind of device I have to install Windows (not an edition of recovery or anything like that, but a whole new windows on the formatted HARD drive)?

  I also have another problem: whenever I plug a USB device (I tried the DVD drive external and a USB keyboard) when I start the laptop, it seems to hang. At least, I am not able to type anything more; the keyboard of the laptop is dead (the point where the entrance would still be flashing in the BACK platform, but typing. sth on the keyboard isn't doing anything). It is not normal, is it?

  I also tried to get to the BIOS, but I tried various commands (F1 to F12, DEL etc.), but I couldn't access the BIOS. It would be great if someone could tell me the command for it.

  Thanks in advance for the help and sorry for the bad English, I'm not a native speaker :)

  The forum has a search function, but to help you look still these 2 wires:

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=19232
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=23921

  Here you can see that XP installation isn't very easy, but can be done successfully

  as long as you are working in an environment with appropriate back-drivers back, you can use any kind of external (USB or pcmcia) CD player you want

  the bios is accessible by pressing ESC and the Start button

• Installation of the USB - no scanner detected by the software

  I bought Microtec USB scanner ScanMaker6100 but cannot begin to work with it:)

  Recognize the scanner as a Plug & Play device my PC and install it but the software can't find it.

  I tried to scan on another PC to check and it works so I have problem with my TOSHIBA A60?

  I had send my PC profile to support of Microtec and they suggest the following:
  "your installation of USB needs chipset driver. Currently, he works in "universal". Unmanned correct install cannot USB chipsets support entirely. Normally you have the computer driver MB CD when you buy the computer. »

  My USB controllers in Device Manager are installed like:
  Standard enhanced PCI to USB Host Controller
  Standard openHCD USB host controller
  In devices, I see they are ATI SB200 - USB Controller and ATI SB200 - USB 2.0 Controller.

  I really should reinstall / update my USB driver? How? Where can I get these drivers?

  [Edited by: admin July 16 05 12:34]

  Hello

  I don't think you need to install or update the USB drivers. If the scanner is properly installed and recognized there must be another problem. In my opinion, you should try to use the scanner with another program. As far as I know, you can also use Microsoft word and try to import image from a scanner. If Office is installed on your device, try to import something in the word document.

  Good bye

• no internet tv after installation of the usb tv tuner!

  I recently bought a HP laptop g62-228 ca series.

  I had set up the center of windows media, (no problem in doing so).

  I was able to open/Internet t.v and view them (especially short video clips / some full episodes, very crisp clear picture.) a lot of the content could not be considered because I reside in the Canada.

  After installing the usb tv tuner and set up for regular tv viewing with my local cable provider. (no problem with that too).

  I could not open/access channels or videos even as I liked be4 I had installed the tv tuner. I can see them in the Guide and even highlight, but I can't open them.

  If someone can help me solve this problem, so I can return to view internet tv. on my laptop?

  I would be very grateful.

  P. S.

  the tuner, I bought says it supports NTSC; ATSC; & clear QAM.

  poonman61

  Hello

  Unfortunately, Internet TV is not available in the Canada.

  David
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Installation of the USB Modem problem

  I am trying to install a Telstra 4 G mobile USB modem on a Dell Ultrabook on Windows 7, keep this message ' VB Script run time for custom action ' won't complete installation

  Update your Windows and install the latest update.

  Visit the website of support if your modem and install the latest version of the driver.

  Contact the manufacturer support and discuss this matter with them.

• Best installation of the USB driver of practices for non-persistent clones

  Hello

  are there best practices using non-persistent clones and USB driver?

  Client A connects to a linked clone and connects a drive USB flash or something else.

  The installation of the driver is horrible slow on Windows 7:

  • New device found...
  • looking for a driver in driverstore...
  • installing the driver software...

  Tested now and it took more than 8mins.

  After installation, the appliance is ready and can be used. But after disconnecting from the desktop computer updates and each driver installation must be run again at the next connection. We have disabled the Windows updates and specified do not search Windows Update for device driver locations. (Policies-> models-> system administration / Installation of devices-> search order specified for the device driver source locations).

  Clues, why it is so slowly installing drivers and how to prevent the reinstallation of drivers every day

  Thank you and best regards

  Well,.

  We have set. VA was the problem...

  We excluded analyzes the demand for processes drvinst.exe.

  Thank you

• Problem with Installation of the Siebel Web Server Extension

  Hello
  IAM trying to install Siebel 8.1 on my pc... In fact its installed successfully... but due to some other reasons (to increase disk space on the C drive) I uninstalled it.
  Clean registry and deleled installation folder files. but when I am trying to reinstall it cannot go further to Siebel Web Server Extension. He stopping at the beginning... and the error is
  "Cannot find table.txt from the previous installation.
  Setup cannot continue.
  java.io.FileNotFoundException:
  "c:\sba\SWEApp\_uninst\eappweb\table.txt (the system cannot find the path specified).
  
  I uninstalled everything that he and cleaned the registry keys as well.
  could you please help me how to fix this error...?

  Hello

  Assuming you are using windows 2003 and you have not installed another siebel server software, go to c:/windows folder, make a backup of the current vpd.properties file, remove it and restart your installation again. file VPD. Properties is created by installshield to keep track of the facilities. It is always good to have a backup in case you have problems installing. Support.oracle.com Doc ID 520528.1 has more information on this file.

  It will be useful,

  Wilson

• Installation of the USB-5680 kills Labview

  Does anyone know why the software that comes with the USB-5680 power meter would cause Labview 8.2 no longer start successfully? I think that the error was: an unrecoverable internal error: lvint.cpp, line 1538.

  Hello LabTech,

  I don't know what is the cause of your problem, but you can try to replace the file ni568x.rc with the attached to this knowledge base article. I found a question where to replace this file corrected exactly the problem that you see. I would like to know if it works and if you have any additional questions.

• Publish with the installation of the USB SFD 321U/HP floppy drive.

  Can someone help me: I have an old USB SFD 321U/HP floppy drive and would like to find a driver for my Windows 7 to this regulation.

  Install a NEC USB Floppy driver and it will work in Windows 7 64 bit. Worked for me.

  Details are here: http://www.techgeekandmore.com/2009/12/11/hardware-getting-the-iomega-usb-floppy-drive-to-work-with-windows-vista-and-windows-7/

• Installation of the USB-6211 for DA

  I try to use a USB-6211 housing in a very simple system of Visual Studio C++. The final goal is to continuousely output for both channels to 180 samples per second. At this point, I have the following Setup:

  DAQmxErrChk (DAQmxCreateTask("",&taskHandle));
  DAQmxErrChk (DAQmxCreateAOVoltageChan (taskHandle,
  devcmd, //physical channel
  ' ', //name assigned.
  -10.0, the production of //min value
  10.0, output value of //max
  DAQmx_Val_Volts, release //units
  "" scale //custom name
  ));
  DAQmxErrChk (DAQmxCfgSampClkTiming (taskHandle,
  "", //source (default OnboardClock)
  180.0, //rate in the samples per second
  DAQmx_Val_Rising, //active edge
  DAQmx_Val_FiniteSamps, finite number of samples (to change) //a
  samples_to_write //samples to acquire
  ));
  DAQmxErrChk (DAQmxStartTask (taskHandle));

  On the last drive, I get the message:

  Non-bufferered of NI by the equipment operations are not supported for this device and the type of channel. I can't make any sense of it. Any suggestions?

  One of your support staff helped on the phone. It appears as a somewhat obscure command

  DAQmxSetWriteRegenMode (taskHandle, DAQmx_Val_DoNotAllowRegen)

  It takes to get buffering to work properly. It is a command badly documented, and there is no real indication that this is necessary.