Intermittent output HDMI (sound and vision) Z70-80

Similar Questions

• Satellite A300-1LT - I have to manual activate HDMI sound

  Hi all,

  This program (Manager of HDMI) do not work for me, I have to manual activate HDMI sound and when I want to connect or disconnect the display they do not recognize when I plug in the cable.
  So everything has manual (centar media connect display...)
  Install and uninstall the progam does not help...

  Thanx

  Hello!

  Have you tried to update the Manager of HDMI and sound card? Time you can find the Toshiba site and maybe market so try:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Last but not least I founded this Toshiba document and perhaps that it s useful to you:
  http://APS2.toshiba-tro.de/KB0/TSB8B02HW0000R01.htm

  Good bye

• Playback devices does not recognize an output HDMI for sound!

  I have my HDMI connected with video but my output of sounds/audio/playbackdevices does not recognize that I have a connected TV, how do audio? theres no monitor to set as audio device by default!

  Normally, HDMI carries audio as well as video, so choose HDMI as the included default playback device work. If you don't see a HDMI, try:

  Click on:

  Start-> Control Panel-> Sound > tab reading .

  Now right click on an empty area and make sure that see the disabled devices and see the disconnected devices are enabled (checked). If your playback device (HDMI) appears, right-click on it and select enable. Now, right click on them again and select set as default device.

  If the above does not try to install the latest package of graphics driver that they usually contain the necessary audio drivers for output over HDMI.

  You can also check that your graphics card is capable of audio over HDMI output as some may not.

• Not plugged into the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Original title: high speed HDMI does not.

  I plugin the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Hi lisa,

  Try these steps and check the result.
  Step 1: Manage audio devices
  a. Click Start and then click Control Panel.
  b. click hardware and sound.
  c. under sound, click on manage audio devices.
  d. click on the playback device you want to output sound. Right-click in the empty space and click on see the disabled devices to see other devices.
  e. Select the device and click on set as default and then click OK.

  See http://support.Microsoft.com/kb/953500

  Step 2: Graphics output to monitor
  a. right click on the desktop, click chart options.
  b. output to monitor.

  Step 3: Adjust graphics hardware acceleration
  a. open the screen resolution by clicking the Start button, Control Panel, and then, under appearance and personalization, click on adjust the screen resolution.
  b. click Advanced settings, click the Troubleshooting tab and then click on change settings.
  Note: Some video card drivers do not allow allows you to change the settings.
  c. move the hardware acceleration slider at different levels and check the result.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• XBR-55X850C is no longer any HDMI sound output

  I played an Xbox and exchanged on my pc this morning which is connected via HDMI as well and had her all morning at a time. TV turned off the coast and did a few hours NAP and go on my pc and now none either sound comes through any source HDMI, not an Xbox, Playstation 4, but the sound works for applications and the cable. I unplugged the back of each device's HDMI cords and swapped 'em out and swpaped cords around each unit with no results. I also noticed at the top the screen am I on will not disappear, I am on HDMI 1, which is my pc it stays on until I hit the remote control display.

  And a few moments after posting what he says no TV entry closing in 1 minute.

  Problem solved with hard reset.

• sound and Vibration Assistant. Speaker output

  I am new to the sound and Vibration Assistant and he had to get monitored sound of a surfboard 4722 the speaker to computers.  I can capture data and display it, but I want, but can't seem to find a way to get the sound to the speakers.  Thanks for any help

  Hi Mike.

  Unfortunately, the Sound and Vibration Assistant doesn't have a built-in way to route your signal input to your speakers.

  However, if you have LabVIEW, you can add a step to run a LabVIEW VI that generates output a file from your computer speakers (or external speakers).  You must write a LabVIEW program that either acquires a signal or load a file of recorded signal, then this signal to your speakers.  "You will most likely use the Play Waveform Express VI of the Express" exit pallet on the block diagram.  "After you wrote this program, you need to add a step in the sound and Vibration Assistant using the Add a step" run a LabVIEW VI.

  I hope this helps.  Good luck with your application!

• Loss of the HDMI sound after the monitor stop

  System:

  HP laptop computer dv9330ca on Vista 64-bit. NVidea GE Force 7600 and Conexant audio.

  I have hooked the lappy HDMI cable to the TV (Toshiba 32DT2U or 32C110U, not sure) and had no sound.  Define sound from digital output (SPDIF) in Control Panel - still no sound.  Video drivers updated - make us it sound.  Update audio drivers - sound disappeared. Audio restoration pilot - still no sound. Re-install video drivers - make us it sound.  Reboot - we still have sound!  The Toshiba power on and turn it on again - no noise :( Re-install video drivers - still no sound :(

  I rebooted after all the steps mentioned above.  I am aware of "the digital sound setting" in Control Panel, but it's not helping more.

  Any suggestions?

  Thanks in advance!

  * UPDATE *.

  I thought if I have no sound HDMI anyway, I might as well re - install the latest video driver again...

  HDMI sound came back after restart >.

  I'm sure I have will lose it again, probably when I stopped - the system, but I thought that I'll let you know - cordially

  Thanks again for your time.

• hdmi sound

  Hello!!!
  I put the hdmi cable and I can see the image on the tv but I have no sound...
  the problem occurs now I saw movies with her a long time ago, but now I can not...
  can someone help me?

  Hi buondi'sarei

  By default the Vista transmits no sound on HDMI output.  To change this to change the settings in the control panel. We can also update the drivers for the device.

  Step 1:

  Note: This turns off normal audio output sound on the system or speakers.  To get that back, you will need to reverse this process.

  1. click on the button 'Start '.

  2. click on "Control Panel."

  3. with the control to the "Control Panel Home" Panel, click on 'hardware and sound '.

  4. where it says "Sound" in green letters, there are three options below that are in blue, click on "manage Audio devices".

  5. This will bring up a window titled "Sound".

  6. on the tab 'Read' it has listed the sound options at your disposal. It should read "peripheral digital output (HDMI)" click on it.

  7. it should now check this option box.

  8. the sound should play through your HDMI connections to the TV.

  You need to update your drivers if incase the above step does not work.

  Step 2: We can try to day drivers to the most recent and check if it works.

  Step 3: If it is a recent problem, we can try a System Restore.

  After back and let us know if it helped to solve your problem.

  Thank you and best regards,

  R uma - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• New Blu - Ray HDMI sound problem

  Whenever I play a most recent blu - ray with the Mediasmart DVD application disc, I get only sound through my speakers laptop even if my TV is plugged into the HDMI port and I can say that the port is the current output device into the cursor of the mouse on the sound icon on the taskbar.  I updated the driver program and its Mediasmart as much as I could.  If I play an old blu - ray or DVD, the sound comes out of the TV very well.  In addition, any other application that uses sound works fine too.

  I tried the suggestion of HP in the FAQ where they tell me to put the "SPDIF (Digital out via HP docking station)' as the default in the sound control panel device.  But I don't get all the sounds for any application to do this.  I've noticed that the SPDIF device using IDT audio codec high definition, which is the only sound driver that I can update.  The NVIDIA HDMI output device which is under it in the control panel uses the NVIDIA High Definition audio instead, and I don't know how update if necessary.  Any suggestions?

  BTW, I use a laptop HP HDX 16 with Vista Home premium 64-bit.

  Message edited by nodakjoe on 08/24/2009 22:34
  Message edited by nodakjoe on 08/24/2009 22:35

  I had the same problem.  Here's what worked for me:

  Remove the drive blueray disc.

  Reboot the laptop.

  Turn on the TV and select it's an HDMI input.

  Connect the HDMI to the TV cable to the laptop.

  The display shall transfer to the TV (laptop becomes black)

  Open the Mediasmart drive.

  Select DVD

  Open "Settings" (the gear symbol)

  Click the tab "Audio".

  Select "HDMI passthrough" and apply.

  NOW, put the blueray disc in the drive.

  Give it some time to start on its own.

  (Note; If you try to adjust the "settings" with a disc in the drive, or without going through the HDMI cable connected, the "HDMI" passthrough not appear as an option.)

  Now that I have followed this procedure, I got no additional problem. TV audio plays, not the laptop, and I can use my home theater sound system to take the "audio" television and he takes in my cable box (and increase the volume of the TV at the bottom).

  I hope this helps. I was pulling on my hair until I discovered this. Let us know if it works for you.

  Message edited by hd1 on 2009-08-25 09:39

• HDMI sound has stopped working - dv9266ea

  Hey!

  I have a laptop dv9266ea with WinVista Home Premium and a few 1-2 months ago my sound does not work as it should. We used to be able to plug the laptop to our TV using a HDMI cable and change the sound default and everything was good, but now we have not any sound at all more. Photo is excellent as usual.

  Are more people who has the same problem, so it might be because of some update somewhere here? Or anyone knows of another solution?

  Never mind. Swedish support couldn't give me an answer. American support couldn't give me an answer. 2 times I had the mother exchanged at just 1.5 years (the last time they destroyed the volume controls and said that they didn't fix it for me, even if they one wrecked at HP), and my brother had his mother traded 3 times on a similar model.

  HP seems to suck. I'm going to buy a new laptop to mark another in a few weeks and then it goes in the trash. I lost the way a lot of time and money because of all it's flaws and time away for repair.

  Solution: Trash and get another brand.

  Message edited by LordMagnus on 02/06/2009 12:38 AM

• Output HDMI does not work on Satellite L775

  Hello.

  I have a new Toshiba Satellite L775 with HDMI output.

  I wanted to connect the laptop to my TV to watch pictures via HDMI.
  But it did not work.
  I connected the laptop with HDMI cable for my Samsung - LCD - TV screen.
  Time, wireless and TV are already functioning. (Normally I use the cable for TV receiver, with no problems).

  I tried to change the output with Fn + F5 to TV-monitor (or TV-monitor & laptop).
  But the TV does not detect not the laptop, in any case.

  What's wrong?

  Thanks for the solutions.

  Best regards
  WE34

  I agree with Feliks if the TV supports different HDMI ports, you must make sure that the TV has been set to the correct HDMI port.
  Choose in the settings of the TV the HDMI port and then you can use Fn + F5 to switch to the TV output.

• Portege M800-105 - output HDMI for XP driver?

  Hello

  I have a question that belongs to the HDMI output.
  I put Windows XP Home on my Portege with all the driver from Toshiba support page but my HDMI output does not work.

  Now, I saw that there is a driver for Vista called output HDMI Toshiba.
  Anyone know a driver called like this for Windows XP?
  Or does anyone have the same problem with XP but the HDMI does not work?

  I hope someone can help me with this problem.

  THX

  dschumacher

  Hello

  As much as I know, that he is a driver Intel High Definition Audio HDMI.
  I m not a M800 owner but I ve got a Satellite U400 with HDMI output and installed XP.

  To be honest I didn t notice any yellow exclamation in my device manager but I installed the page Intel's Intel High Definition Audio HDMI driver
  http://www.Intel.com/support/chipsets/sb/CS-009244.htm

  Maybe this site will help you

  But note; Some features of the laptop not available in Win XP, but only under Vista!

• Satellite L650-1GC - output HDMI No.

  I plugged my L650-1GC HDMI output to my TV I've done several times in the past, but the display settings do not see the second monitor.

  Other forums seem to suggest that this is not uncommon, but no one offers a reliable solution.

  I'm on Windows 7 Home Premium, 64-bit.
  I tried different cables and different contributions to the (Bravia) TV

  I also reloaded the driver.

  Any advice would be appreciated.

  Thank you

  Hello

  For the video signal via HDMI, you must connect both devices with a HDMI cable and I finally must use combinations of keys FN + F5 to choose place you in video output.

  Of course, we must ensure that the right channel HDMI was chosen on your TV.

  By the way; try to set the BIOS (F2) to the default settings

• Difference between signal y express sound and Vibration Assistant

  Buenas,

  Cuando instalas el of sound and vibration luego software, tienes back ejecutables: Sound and vibration assistant y signal on purpose. Los abres los back if you lo lo mismo. Mid questions are:

  • What difference between hay?
  
  
  • Da igual use uno u otro
  
  
  • If desinstalo uno los pasa algo back?

  MUCHAS gracias

  Saludos

  Hola, aaramburu,

  in lenguaje andar por casa, Signal Express are el programa matriz y S & VA el are UN modulo what instala encima y reviews una paleta Programación than permite usar funcionalidades specific sonido Análisis y constant. El Signal Express has leaves, apply filters, a configurable software para datos closing, etc. If el S & VA mallards are mallards nuevas funcionalidades enable use tarjetas para señales dinamicas o DSAS that enable leer of tacometros, acelerometros, hacer análisis octavas, etc.. ES como if instalas LabVIEW, are UN lenguaje general Programación y quieres una camara use. Sober el propio LabVIEW has instalar Modulo de Vision para el LabVIEW y is anaden kbes imagen aforementioned funcionalidades.

  No nada desinstales, one extended capabilities. As has using uno u otro, depends on the nature of the application as desarrolles. If going to a Signal Express y seleccionas help > Getting Started with > Getting Started with LabVIEW Signal Express Fiesta el tutorial Básico para el manejo del entorno con guiados exercise. Leads unas cuatro horas. If you want to develop una application of sonido y vibration, using a high port tal y como is muestra in el tutorial help > Getting Started with > Assistant Sound and Vibration.

  I hope this information you follows from utility.

  Jesus.

• HDMI Audio and Windows 7

  I'm trying to connect my Pavilion dv6 on my HDTV with a HDMI cable. I make the video, but no audio on the TV speakers. The problem started after I upgraded from Vista to Windows 7. I had no problem with HDMI with windows Vista.

  I tried to date/reinstall the audio drivers from the HP website, but it does not work. I also tried to go into the control panel and change the playback device, but the HDMI audio device icon no longer appears in the playback devices dialog box. Read-only devices are speakers and headphones double independent double headphones and SPDIF (Digital Out Via HP dock.)

  How can I solve this problem? Why the HDMI device is not displayed in the reading dialog box?

  Hi all HDMI his problem solved after I installed the new windows 7, icon hdmi on the menu of display devices have disappeared.  Here's what I did and the icon go back and redo the sound work of hdmi. Graphics cards intel must be updated. The link below will take you to the site intel and it detects the updates required for your system. http://www.Intel.com/support/detect.htm run the program and install the required updates and then restart windows. HDMI icon will be back and the sound will work normal as before.  I hope it will solve the problem of everyone with the hdmi sound problem. I have hp Pavilion dv6, I'm happy to hear the clear sound crisp again of my bar of his Philips HTS 8100. Kevin www.canvasdelight.com