Internet access full tunnel - ASA5505

Similar Questions

• ASA 5505 VPN works great but can't access internet via the tunnel to customers

  We have an ASA 5505 ASA 8.2.1 running and using IPSec for Remote access clients in the main office.  Remote access is a lot of work, with full access to network resources in the main office and the only thing I can't get to work is access to internet through the tunnel.  I don't want to use split tunneling.  I use ASDM 6.2.1 for configuration.  Any help is appreciated.  I'm probably missing something simple and it looked so much, I'm probably looking at right beyond the error.  Thanks in advance for your time and help!    Jim

  Add a statement of nat for your segment of customer on the external interface

  NAT (outside) - access list

  then allow traffic routing back on the same interface, it is entered in the

  permit same-security-traffic intra-interface

  *

  *

  * more than information can be found here:

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807...

  On Wednesday, 27 January 2010, at 23:12, jimcanova

• No Internet VPN IPsec Tunnel access

  I use the Netgear VPN - Pro 5.51.001 client to configure and run a VPN Tunnel to a UTM10 (3.5.2 - 14). It works very well so far and my private network resources could be achieved.

  When the tunnel is established, the client (W7 x 64) loses connectivity to the Internet on LAN or WLAN port desired and expected.
  Now, the Internet connection must be provided inside my private behind the UTM network.
  Due to a DNS SERVER running on my private network addresses (even on the internet) are correctly resolved (use NSLOOKUP to check), but cannot be routed to my VPN client.
  I found, that the map virtual Green-bow had no entry for the gateway, but the entry door (my UTM10) could be ping from the VPN client.
  After you enter the internal IP address of the UTM in the field of "Redundant GW" of the client software and restart and reconnect to the customer,
  the entry door is now displayed in the properties of Green-bow (ipconfig on CMD-screen), but still no internet site can be reached.

  To test, I have disabled the firewall on my client PC.
  The tunnel use mode-config and receives the entries in DNS and WINS server according to the config folder. The client is configured to force the NAT-traversal.

  Customers should be able to connect from the offices at home (or mobile) to the network/domain of society and use internet as if they were connected locally.
  SSL - VPN is not an option.

  m.Vogel wrote:
  Now, the Internet connection must be provided inside my private behind the UTM network.

  No, it doesn't work like that. If you want to "full-tunnel" support you need to stick with SSL VPN and select this option in the settings.

• No Internet for complete Tunnel access

  We have an ASA 5550, ver 8.0 (5) and using IPSEC client for remote access in the main office.  Remote access works very well with Tunnel from Split.  We can access the resources network and go on the internet with Tunnel from Split.  However, we can only access network resources, but not for complete tunnel internet access.  Do you have any suggestions?

  Thank you.

  Diane

  Diane,

  You will need to nat of your pool RA VPN network using your interface global nat ID 1.

  For complete tunnel, add two other statements

  permit same-security-traffic intra-interface

  NAT (outside) 1

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  Concerning

• Why my application requires "full Internet access.

  I create a built-in apk for GooglePlay with Adobe AIR version, and my application requires "full Internet access. I did not indicate this requirement of authorization, but it seems, why?

  An application built in Flash or Flex, works on 'AIR' in Android, does not run in native mode and how to connect 'AIR' with Android, is via a local network, while permission 'Full Internet access' is to allow a local between AIR and Android connection, Yes, I know it's silly, but it is so.

• No Internet access when VPNd in ASA 5505

  My problem is just like the title implies. Any internal host can access internet with on all issues. When I VPN in the network I can access all internal networks but can't access Internet sites.

  I have used packet tracers in ASDM with the following parameters: an address from the pool of the vpn and the address of a site with all ports. Plotter package says that the package should be allowed.

  In addition, the connection series to debug I never see what a hit the newspaper package that is intended for the land of the Internet.

  DNS seems to work as it should.

  What I'm missing! Thanks in advance for all your help.

  Hi, from your description seems just configured RA vpn full tunnel? If this is the case could you confirm you are from your vpn for outgoing network...

  typically for RA full outgoing internet tunnel you would nat pool vpn network and allow return traffic

  the same interface, it came with dry even allow intra interface statement.

  NAT (outside) 1

  permit same-security-traffic intra-interface

  Have a look here for reference

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  Concerning

• Satellite NB10t-Arelatifs victory 8.1 - limited wifi, no internet access connection

  Hello

  so I have Windows of Satellite NB10t-a 8.1 with qualcomm atheros adapter ar956x and im getting connection is limited message, unidentified network, no internet access despite the full bars messsage.

  I have other laptops and computers that run windows 7 etc in the House connection very well.

  I tried pretty much everything that any help at all would be really appreciated.

  > I tried just about everything at all any help would be really appreciated
  and what have you tried exactly?

  Have you tried to update the driver Wlan?
  Have you tested the WLan in relation to other Wlan routers?
  Have you tested different channels WLan (1-11) and different standard WLan (802.11 A/B/G/N)
  Did you test the connection to the WiFi which is not encrypted?

• why I don't get internet access? Help, please!

  Why when I connect to my wifi, I'm permitted little or no internet access, but it still shows me trhat I'm connected?

  Hi Chris Naylor,.

  1 Windows operating system you are using?

  2. have you been able to connect to before without any problem?

  3. did you of recent changes on the system?

  Method 1:

  You can read the following article and try to run the troubleshooter and check.

  In the Windows wireless network connection problems

  Method 2:

  You can try to update the wireless adapter and see if it helps.

  Updated a hardware driver that is not working properly

  Method 3:

  Disable IPv6

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.
  NOTE: You should do this for each network connection.

  Method 4:

  You can also temporarily disable third-party security software and firewalls installed on the system and check if the problem persists.

  Note: Be sure to enable the security software on the computer after checking.

  For more information, you can consult the following article:

  Solve problems, find wireless networks

  Hope this information is useful.

• After the abduction of a trojan virus, I still have no internet access

  After the abduction of a trojan virus, I still have no internet access with Internet explorer, Google Earth, or Yahoo Messenger. Attempt to update Yahoo Messenger from a download of update, a message indicates "Yahoo Messenger is unable to download files needed for installation. Please check the firewall settings and try again. It does not matter whether or not the firewall is disabled. Yahoo Messenger is able to connect, but not to show me the list of the rooms in the right panel. Firefox still works fine and all I use.

  Here are a few things to check after an infection or elimination:

  We will check your network connection properties.

  Some malware will alter these settings and your anti malware software can't tell if you have changed the malware changed them or so, after removal of infections, it will leave just the settings as he finds them (it is usually a good thing), but can leave your disabled Internet access.

  Click Start, run and enter in the box:

  Inetcpl.cpl

  Click OK to launch the Internet Properties Control Panel, choose connections, LANsettings.

  Or, in Internet Explorer click on tools, Options, connections, LAN settings.

  These settings control your Internet access for all browsers.

  (If you make settings, write them down so you can undo changes if you must)

  On most environments, not independent, there will be check automatically detect settings and the other boxes are (as Proxy Server) is disabled.

  Automatically detect the setting checked =
  Use the automatic configuration script = unchecked
  Use a proxy server for your LAN = not checked

  Make changes, then click OK, OK to save the settings.

  Check your settings for how your network adapter gets its IP and DNS settings.  On most home systems, these parameters must be defined for the system will get the settings automatically.

  If you have another system on your network that works, you can compare these settings with the settings of the system which is not a work and make adjustments.

  Click Start, settings, Control Panel, network connections, and then select your current network connection.

  On the general tab, click Properties.

  In the drop down in the Middle, find and highlight the selection of Internet Protocol (TCP/IP) and click Properties.

  In the Internet Protocol Properties window, the usual selections are to get the IP and DNS settings automatically.  Select the following two options:

  Obtain an IP address automatically
  Get a DNS server address automatically

  The rest of the options on the screen should then be grayed out/not available.

  Make changes, then click OK, OK to save the settings.

  Restart your computer and test your connection.

  If it still does not work, check your settings are still in place after a restart and then release and renewal IP of your network device configuration settings.

  Click Start, run and enter in the box:

  cmd

  Click OK to open a command prompt window, and then type the following commands:

  ipconfig/release

  ipconfig / renew

  output

  Restart your computer and test your connection.

  Download, install, update and do a full scan with these free malware detection programs can solve any problems:

  Malwarebytes (MMFA): http://malwarebytes.org/

  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  It can be uninstalled later if you wish.

  Do, or do not. There is no test.

  I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• Internet access WRT54GS - No.

  Hey, Ive had problems with internet connection for these days and ive been what I do usually just unplug the router and the modem and turn their back on but that did not work this time, its connection again but it just says not: no internet access, but it will connect when I connect my laptop to the modem Anyone know what I have to do?. is my router linksys wrt54gs version 6

  Go ahead and perform a hard reset full and reconfigure the router back to normal.  See if that helps.

• Wireless connected but no Internet access

  I have a new (5 months) Acer Aspire 5732Z which works in Windows 7. Wireless connection shows that it is connected (full bars) but I have no internet access (there is a signal of yellow exclamation over bars error). I have another laptop running Windows XP which connects well to the same wireless router and wireless for Acer worked very well so far. I was on the phone with my ISP and they said, because it shows that the computer is connected to the wireless, they cannot help me. Anyone has any ideas that can help me?

  Thank you. I decided to call my Internet provider again and this rep was able to solve the problem without delay. From what I learned, if you get a representative who was not helpful, call again...

• Internet access problem

  I don't know it is purely a problem of Vista, but the tech at my IP guy thought so. I'd appreciate any help that anyone can give!

  Details: HP Pavilion, Windows Vista, by modem cable (not wireless).

  Last week, my IP had a power outage in my area. My internet has completely disappeared for a few hours. When he returned, my internet connection was not quite right. I had access to some web sites, but not others. Some web sites would only partially (ie. text but no pictures). It's true that I used Internet Explorer or Safari. In addition, AOL Instant Messenger would work not (connection failed).

  I contacted the technical support of my IP the next day. A high level (supposedly) tech guy helped me for several hours. He had me doing many tests, including completely un-installing my anti-virus (Norton) to see if that would help. No change.

  He sends a new modem for me the next day to see if that was the problem. The modem works fine, but it did not help. (The guy who tested my line on his laptop computer. He had full internet access. "I was still unable to connect to several websites, or PURPOSE, same as before).

  After that, the tech guy refused to help me no more. He said that he was strictly a PC problem. I agree that there must be something wrong with my PC, no doubt with Vista, although all the problems began immediately after the failure (and everything was fine before this).

  I would really like to understand this problem, so any help would be GREATLY appreciated. Thank you.

  I want to thank all of you for your help. For some strange reason, everything returned to normal yesterday, without changing me anything on my PC. I don't know how this could happen, others that it really was a problem with my provider, and something got zero to their end somehow. Yes, which is not supposed to, but nothing about it makes no sense either.

  Anyway, thanks again for the help.

• No Internet access after the connection of the cisco vpn client

  Hi Experts,

  Please check below config.the problem is vpn is connected but no internet access

  on the computer after the vpn connection

  ASA Version 8.0 (2)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.10.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 192.168.14.12 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
  INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
  55.240
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool testpool 192.168.14.240 - 192.168.14.250
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access INSIDE_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.14.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
  Crypto-map dynamic dyn1 1 set transform-set setFirstSet
  Crypto-map dynamic dyn1 1jeu reverse-road
  dynamic mymap 1 dyn1 ipsec-isakmp crypto map
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  password encrypted user testuser IqY6lTColo8VIF24 name
  username password khans X5bLOVudYKsK1JS / encrypted privilege 15
  tunnel-group mphone type remote access
  tunnel-group mphone General attributes
  address testpool pool
  tunnel-group ipsec-attributes mphone
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
  : end
  ciscoasa #.

  Hello

  Large.  Try adding the below to make it work

  vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

  NAT (inside) 0-list of access vpn-sheep

  Harish

• No internet access through VPN

  Hi, I have the router Cisco 881 (MPC8300) with c880data-universalk9 - mz.153 - 3.M4.bin when users establish a VPN connection to the corporate network, had access to all the resources but no internet access, please help me what else I need to configure to achieve my goal. I don't want to split the tunnel, internet via VPN, users must have. In my opinion, I have put an additional configuration for NAT, but my router not recognize u-Turn and NAT commands on the object on the network.

  My config:

  Building configuration...

  Current configuration: 13562 bytes
  !
  ! Last configuration change at 09:52:38 PCTime Saturday, May 16, 2015, by admin
  version 15.3
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  XXX host name
  !
  boot-start-marker
  start the flash system: c880data-universalk9 - mz.153 - 3.M4.bin
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login ciscocp_vpn_xauth_ml_1 local
  AAA authentication login ciscocp_vpn_xauth_ml_2 local
  AAA authorization exec default local
  AAA authorization ciscocp_vpn_group_ml_1 LAN
  AAA authorization ciscocp_vpn_group_ml_2 LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  iomem 10 memory size
  clock timezone PCTime 1 0
  PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
  !
  Crypto pki trustpoint TP-self-signed-1751279470
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1751279470
  revocation checking no
  rsakeypair TP-self-signed-1751279470
  !
  !
  TP-self-signed-1751279470 crypto pki certificate chain
  certificate self-signed 01
  XXXX
  !
  !
  Protocol-IP port-map user - 2 tcp 8443 port
  user-Protocol IP port-map - 1 tcp 3389 port
  !

  !
  !
  !
  IP domain name dmn.local
  8.8.8.8 IP name-server
  IP-server names 8.8.4.4
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ174992C8
  !
  !
  username privilege 15 secret 5 xxxx xxxx
  username secret VPNUSER 5 xxxx
  !
  !
  !
  !
  !
  !
  type of class-card inspect sdm-nat-user-protocol--2-1 correspondence
  game group-access 105
  corresponds to the user-Protocol - 2
  type of class-card inspect entire game SDM_AH
  match the name of group-access SDM_AH
  type of class-card inspect entire game PAC-skinny-inspect
  Skinny Protocol game
  type of class-card inspect entire game SDM_IP
  match the name of group-access SDM_IP
  type of class-card inspect entire game PAC-h323nxg-inspect
  match Protocol h323-nxg
  type of class-card inspect entire game PAC-cls-icmp-access
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect entire game PAC-h225ras-inspect
  match Protocol h225ras
  type of class-card inspect entire game SDM_ESP
  match the name of group-access SDM_ESP
  type of class-card inspect entire game PAC-h323annexe-inspect
  match Protocol h323-annex
  type of class-card inspect entire game PAC-cls-insp-traffic
  match Protocol pptp
  dns protocol game
  ftp protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  netshow Protocol game
  Protocol shell game
  match Protocol realmedia
  match rtsp Protocol
  smtp Protocol game
  sql-net Protocol game
  streamworks Protocol game
  tftp Protocol game
  vdolive Protocol game
  tcp protocol match
  udp Protocol game
  type of class-card inspect the correspondence SDM_GRE
  match the name of group-access SDM_GRE
  type of class-card inspect entire game PAC-h323-inspect
  h323 Protocol game
  type of class-card inspect correspondence ccp-invalid-src
  game group-access 103
  type of class-card inspect entire game PAC-sip-inspect
  sip protocol game
  type of class-card inspect correspondence sdm-nat-https-1
  game group-access 104
  https protocol game
  type of class-card inspect all match mysql
  match the mysql Protocol
  type of class-card inspect correspondence ccp-Protocol-http
  http protocol game
  type of class-card inspect entire game CCP_PPTP
  corresponds to the SDM_GRE class-map
  inspect the class-map match PAC-insp-traffic type
  corresponds to the class-map PAC-cls-insp-traffic
  type of class-card inspect entire game SDM_EASY_VPN_SERVER_TRAFFIC
  match Protocol isakmp
  match Protocol ipsec-msft
  corresponds to the SDM_AH class-map
  corresponds to the SDM_ESP class-map
  type of class-card inspect correspondence ccp-icmp-access
  corresponds to the class-ccp-cls-icmp-access card
  type of class-card inspect the correspondence SDM_EASY_VPN_SERVER_PT
  corresponds to the SDM_EASY_VPN_SERVER_TRAFFIC class-map
  !
  type of policy-map inspect PCB - inspect
  class type inspect PCB-invalid-src
  Drop newspaper
  class type inspect mysql
  inspect
  class type inspect PCB-Protocol-http
  inspect
  class type inspect PCB-insp-traffic
  inspect
  class type inspect PCB-sip-inspect
  inspect
  class type inspect PCB-h323-inspect
  inspect
  class type inspect ccp-h323annexe-inspect
  inspect
  class type inspect ccp-h225ras-inspect
  inspect
  class type inspect ccp-h323nxg-inspect
  inspect
  class type inspect PCB-skinny-inspect
  inspect
  class class by default
  drop
  type of policy-card inspect sdm-license-ip
  class type inspect SDM_IP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect sdm-pol-NATOutsideToInside-1
  class type inspect sdm-nat-https-1
  inspect
  class type inspect sdm-nat-user-protocol--2-1
  inspect
  class type inspect CCP_PPTP
  Pass
  class class by default
  Drop newspaper
  type of policy-card inspect PCB-enabled
  class type inspect SDM_EASY_VPN_SERVER_PT
  Pass
  class class by default
  drop
  type of policy-card inspect PCB-permits-icmpreply
  class type inspect PCB-icmp-access
  inspect
  class class by default
  Pass
  !
  safety zone-to-zone
  security of the area outside the area
  ezvpn-safe area of zone
  zone-pair security PAC-zp-self-out source destination outside zone auto
  type of service-strategy inspect PCB-permits-icmpreply
  zone-pair security PAC-zp-in-out source in the area of destination outside the area
  type of service-strategy inspect PCB - inspect
  source of PAC-zp-out-auto security area outside zone destination auto pair
  type of service-strategy inspect PCB-enabled
  sdm-zp-NATOutsideToInside-1 zone-pair security source outside the area of destination in the area
  type of service-strategy inspect sdm-pol-NATOutsideToInside-1
  in the destination box source sdm-zp-in-ezvpn1 ezvpn-pairs area security
  type of service-strategy inspect sdm-license-ip
  source of sdm-zp-out-ezpn1 of security area outside zone ezvpn-zone time pair of destination
  type of service-strategy inspect sdm-license-ip
  safety zone-pair sdm-zp-ezvpn-out1-source ezvpn-zone of destination outside the area
  type of service-strategy inspect sdm-license-ip
  safety zone-pair source sdm-zp-ezvpn-in1 ezvpn-area destination in the area
  type of service-strategy inspect sdm-license-ip
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA aes 256
  preshared authentication
  Group 2
  !
  Configuration group customer crypto isakmp Domena
  key XXXXXX
  DNS 192.168.1.2
  Dmn.local field
  pool SDM_POOL_1
  Save-password
  Max-users 90
  netmask 255.255.255.0
  banner ^ Cwelcome ^ C
  ISAKMP crypto ciscocp-ike-profile-1 profile
  match of group identity Domena
  client authentication list ciscocp_vpn_xauth_ml_2
  ISAKMP authorization list ciscocp_vpn_group_ml_2
  client configuration address respond
  virtual-model 1
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac ESP_AES-256_SHA
  tunnel mode
  !
  Profile of crypto ipsec CiscoCP_Profile1
  game of transformation-ESP_AES-256_SHA
  set of isakmp - profile ciscocp-ike-profile-1
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  IP 192.168.9.1 255.255.255.0
  !
  interface FastEthernet0
  no ip address
  !
  interface FastEthernet1
  no ip address
  !
  interface FastEthernet2
  no ip address
  !
  interface FastEthernet3
  no ip address
  !
  interface FastEthernet4
  Description $ETH - WAN$ $FW_OUTSIDE$
  IP x.x.x.x 255.255.255.248
  NAT outside IP
  IP virtual-reassembly in
  outside the area of security of Member's area
  automatic duplex
  automatic speed
  !
  type of interface virtual-Template1 tunnel
  IP unnumbered Loopback0
  ezvpn-safe area of Member's area
  ipv4 ipsec tunnel mode
  Tunnel CiscoCP_Profile1 ipsec protection profile
  !
  interface Vlan1
  Description $ETH_LAN$ $FW_INSIDE$
  IP 192.168.1.1 255.255.255.0
  IP access-group 100 to
  IP nat inside
  IP virtual-reassembly in
  Security members in the box area
  IP tcp adjust-mss 1452
  !
  local IP SDM_POOL_1 192.168.10.10 pool 192.168.10.100
  IP forward-Protocol ND
  IP http server
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  The dns server IP
  IP nat inside source list 3 interface FastEthernet4 overload
  IP nat inside source static tcp 192.168.1.3 interface FastEthernet4 443 443
  IP nat inside source static tcp 192.168.1.2 8443 interface FastEthernet4 8443
  IP route 0.0.0.0 0.0.0.0 X.x.x.x
  !
  SDM_AH extended IP access list
  Note the category CCP_ACL = 1
  allow a whole ahp
  SDM_ESP extended IP access list
  Note the category CCP_ACL = 1
  allow an esp
  SDM_GRE extended IP access list
  Note the category CCP_ACL = 1
  allow a gre
  SDM_IP extended IP access list
  Note the category CCP_ACL = 1
  allow an ip
  !
  not run cdp
  !
  Note access-list 3 INSIDE_IF = Vlan1
  Note CCP_ACL category in the list to access 3 = 2
  access-list 3 Let 192.168.1.0 0.0.0.255
  Note access-list 23 category CCP_ACL = 17
  access-list 23 permit 192.168.1.0 0.0.0.255
  access-list 23 allow 10.10.10.0 0.0.0.7
  Note access-list 100 Auto generated by SDM management access feature
  Note access-list 100 category CCP_ACL = 1
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 22
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq www
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq 443
  access-list 100 permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.1 eq cmd
  access-list 100 tcp refuse any host 192.168.1.1 eq telnet
  access-list 100 tcp refuse any host 192.168.1.1 eq 22
  access-list 100 tcp refuse any host 192.168.1.1 eq www
  access-list 100 tcp refuse any host 192.168.1.1 eq 443
  access-list 100 tcp refuse any host 192.168.1.1 eq cmd
  access-list 100 deny udp any host 192.168.1.1 eq snmp
  access ip-list 100 permit a whole
  Note access-list 101 category CCP_ACL = 1
  access-list 101 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 102 CCP_ACL category = 1
  access-list 102 permit ip 192.168.1.0 0.0.0.255 any
  Note access-list 103 CCP_ACL category = 128
  access-list 103 allow the ip 255.255.255.255 host everything
  access-list 103 allow ip 127.0.0.0 0.255.255.255 everything
  access-list 103 allow ip 93.179.203.160 0.0.0.7 everything
  Note 104 CCP_ACL category = 0 access-list
  IP access-list 104 allow any host 192.168.1.3
  Note access-list 105 CCP_ACL category = 0
  IP access-list 105 allow any host 192.168.1.2

  -----------------------------------------------------------------------
  ^ C
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 102 in
  transport input telnet ssh
  line vty 5 15
  access class 101 in
  transport input telnet ssh
  !
  !
  end

  I'd be grateful for help

  concerning

  Hello

  Enter the subnet pool VPN to access-list 3 for source NAT

  You may need to check the firewall also rules to allow the connection based on areas you

  HTH,

  Averroès

• My network connection shows no internet access, but I can access the internet

  Hardware: Dell XPS 8300

  OS: Windows 7 family

  System type: 64-Bit
  In the network and sharing Center, it is show the connection between the network of Multi and the Internet has an 'X', but I have full internet access.
  Is there a way to fix this?

  Hello

  I understand that you are able to connect to the internet when your computer showing no network connection.

  1. did you of recent changes to the computer?

  I would suggest trying the following instructions and check if it helps.

  Method 1: update the network driver.

  Steps to update of network driver:

  1. click on the Start button.
  2. in the search box type devmgmt.msc, and then press ENTER.
  3. Select the network card device and right click on it
  4. now, select Properties.
  5. in the Properties window, on the driver tab, click Update driver.
  6. After installing the updates, restart the computer.

  For more information visit: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  Method 2:

  Temporarily disable the Antivirus and firewall

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.