IOS to ASA with DH group 14

Similar Questions

• ASA with A/A and three router ISP links

  Can someone help me, I have a problem I need to connect two ASAs with active and I have three routers to three Internet service providers, how do I optimize the gateway redundancy and load balancing.

  and I can use the router to ASA's private beach.

  Another Question is, do I really need host proxy server-based internet access.

  Please help me.

  Concerning

  One solution is to use the Protocol GLBP routers (OSPF in not available in A/A...).

  "GLBP offer deals on several routers (gateways) load balancing using a virtual IP address single and multiple virtual MAC. Each host is configured with the same virtual IP address, and all of the routers in the virtual routing group are involved in the transmission of packets. »

  GLBP group-load balancing [dependent on host: alternating | weighted]

  (see feature cisco IOS to IOS and hardware available browser.) .

  http://www.Cisco.com/en/us/products/ps6550/products_white_paper09186a00801541c8.shtml

  HTH.

  Roberto

• How to associate policies crypto with tunnel-group?

  Hi, when I review the configuration of the VPN from point to point, I have a question. The ASA has three peer-to-peer VPN configuration. So, there are also three groups of tunnel in there. My question is how each VPN to ensure encryption policy tunnel-group? In the anther Word, what encryption policy associated with tunnel-group? Thank you.

  This is the phase 1, they work from top to bottom.  When you try to negotiate the tunnel between two counterparts, in the background, they send all of your policies and according to which is first (from top to bottom) is used.

  For example.

  If your counterpart device uses (3des, md5, pre-shared key and group 2), it will not match the policy 1 and the rest of the policy will not be considered.

  Kind regards

  Sandra

• VPN IPSec ASA with two ISP active

  Hi ALL!

  I have a question.

  So I have ASA with 9.2 (1) SW connected to ISP with active SLA.

  I need to configure redundant IPSec VPN via ISP2, while all other traffic must go through isps1. In case if one of the ISP goes down all including VPN traffic must be routed via ISP alive.

  I have configured SLA and it works.

  ciscoasa # display route performance
  Route 0.0.0.0 isps1 0.0.0.0 10.175.2.5 5 track 1
  Route isp2 0.0.0.0 0.0.0.0 10.175.3.5 10 track 2
  Route isp2 172.22.10.5 255.255.255.255 10.175.3.5 1 excerpt 2

  Here we can see if isps1 and ISP2 are RISING, all traffic passes through isps1, but traffic intended for the remote peer IPSec 172.22.10.5 passes by ISP2.

  This configuration works just at the moment when isps1 or isp2 is down or if a static route for 172.22.10.5 deleted. Where two Internet service providers are increasing to ASA does not send the next remote IPSec datagrams.

  ciscoasa # display running nat
  NAT (inside, isp2) source static obj-INSIDE_LAN obj-INSIDE_LAN destination static obj-REMOTE_LAN obj-REMOTE_LAN no-proxy-arp-search to itinerary
  NAT (inside isps1) source static obj-INSIDE_LAN obj-INSIDE_LAN destination static obj-REMOTE_LAN obj-REMOTE_LAN no-proxy-arp-search to itinerary

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec pmtu aging infinite - the security association
  card crypto cm_vpnc 10 correspondence address acl_vpn
  card crypto cm_vpnc 10 set pfs
  peer set card crypto cm_vpnc 10 172.22.10.5
  card crypto cm_vpnc 10 set transform-set ESP-AES-256-SHA ikev1
  86400 seconds, duration of life card crypto cm_vpnc 10 set - the security association
  card crypto cm_vpnc interface isps1
  cm_vpnc interface isp2 crypto card
  trustpool crypto ca policy
  isps1 enable ikev1 crypto
  isp2 enable ikev1 crypto
  IKEv1 crypto policy 1
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400

  ciscoasa # show ip
  System of IP addresses:
  Subnet mask IP address name interface method
  Vlan1 in 192.168.2.1 255.255.255.0 CONFIG
  Isps1 Vlan2 10.175.2.10 255.255.255.0 CONFIG
  Isp2 Vlan3 10.175.3.10 255.255.255.0 CONFIG

  The main question why?

  Thank you in advance,

  Anton

  Hi anton,.

  If you check the log message on your ASA R301-IS , he's trying to build the tunnel VPN with both IP and it receives packets of asymmetrically your distance ciscoasa.

  TO avoid this asymmetrical connection, point your IP from peers as primary & secondary on your R301-EAST

  set peer 10.175.3.10 10.175.2.10

  Delete the track on your routing entries

  Route isp2 172.22.10.5 255.255.255.255 10.175.3.5

  This should work for you.

  Similalry lower your ISP 2, you should see VPN tunnel is mounted with isps1 one.

  HTH

  Sandy

• tunnel from site to site between router IOS and ASA

  I've combed through the configs on both sides of this tunnel 4 x now and the look of policies as they match. I applied the http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080094498.shtml note

  My crypto lsits access are good and my nat on the side of IOS are provided with a map of the route and look good. On the SAA traffic side on the side of the remote tunnel ASA is exempt from NAT. Each side already has a site to another tunnel configuration, so I added the appropriate lines to the existing cryptographic cards which include peers, transform set and match address 'access-list. The polcies crypto isakmp on both ends are compatible. I have attached some configs and debugs (from router IOS), but essentially the newspaper on the SAA starts with the phase 1 is complete and then routing not received notification message, no proposal chosen readings and then it goes to IKE lost the connection to a remote peer, connection, drop table correlator counterpart has failed, no match, the deletion and finally disconnected session reason lost service.

  Their other tunnel stay standing as well as the configuration of remote access vpn connection is good.

  I found a note that recommends checking any access security-list, so I removed the, but no luck, and a Cisco associated with a hub, but had a healthy logic

  Is displayed normally with the

  Cisco VPN 3000 correspondent

  message hub: no proposal

  Chosen (14). This is a result of the

  being host-to-host connections.

  The configuration of the router has the

  IPSec proposals ordered so that the

  proposal selected for the router

  with the access list, but not the

  peer. The access list has a larger

  network including the host that

  a cutting traffic.

  Make the router for this proposal

  hub to router connection

  first in line, so that it corresponds to the

  specific to the host first.

  but that didn't work either.

  Thank you

  Bill

  Bill,

  Take a look at this

  000610: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): need XAUTH

  000611: * 10:42:15.094 PCTime sep 27: ISAKMP: node set 920927400 to CONF_XAUTH

  000612: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_NAME_V2 attribute

  000613: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_PASSWORD_V2 attribute

  000614: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): launch peer 74.92.97.166 config. ID = 920927400

  000615: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): lot of 74.92.97.166 sending peer_port my_port 4500 4500 (R) CONF_XAUTH

  -Other - 000616: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

  000617: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): former State = new State IKE_P1_COMPLETE = IKE_XAUTH_REQ_SENT

  It should not go to extend the authentication. Since you have the client and the L2L on the same router and clients are configured for Extended authentication, the router will ask for XAUTH unless you configure the "No.-xauth" command after the pre-shared key

  Please implement the command:

  ISAKMP crypto keys in clear text address 74.92.97.166 No.-xauth

  Thank you

  Gilbert

• After that I updated my ios in tune with my ipad some time ago I can not activate my ipad I tried of the apple ID and my password but still can't... How can I reset my apple ID and password?

  I've updated my ios in tune with my ipad this morning... When sound already updated, I can't activate my ipad apple ID and password... what will I do to reset my apple ID?

  Start here:

  https://iforgot.Apple.com

• Protect and control the license for ASA with the power of fire

  I had 1 ASA 5515 initially delivered with the software cx, then made room for the software of firepower and got the virtual firesight for 2 devices and license of TAMAS tha L-5515, but this license was told only the URLs and malware license, I thought that this license was for all that since he has no other licenses in the data sheet and it's Reference with more features.

  How can I get the license protect and control now so I can add the asa with the firepower to firesight and apply to all licenses

  Thank you

  Hello

  L ASA5515-TAMAS = SKU license plans to "MALWARE" and "URLFilter" and legally gives the user to updates of the signature "PROTECT + CONTROL". It does not license "PROTECT + CONTROL". You need to buy "ASA5515-CTRL-LIC =" to license "PROTECT + CONTROL".

  Please discuss a case with CISCO GLO, they can help provide a CTRL license

  -DD

• Cisco ASA with the power of fire vs Cisco IPS Appliance

  Hello

  Question: is there the functional differences between an ASA with the feature of firepower enabled and power of fire IPS appliances 'pure' (e.g. 7000 and 8000 series IPS Modules)?

  Thank you very much!

  Kind regards

  David

  Hello team,

  The same features except hardware bypass and another should trhougputs. Of course the flow rate will be high for hardwrae devices and it also has the ability to bypass equipment. Apart from that URL and all other filtering the same characteristics.

  Rate of good will if this post helps you.

  Concerning
  Jetsy

• ASA with different failover module IPS

  Hi all

  Is it possible to configure the failover of the ASA with different IPS module configuration because we have: ASA 5585-X with firepower PHC-10 and ASA 5585-X with IPS SSP-10

  Thank you

  N °

  Inventories of material (basic unit, memory and optional modules) must be the same in a pair of failover ASA.

• ASA with fire 5555 x Installation/Configuration/full features enablment

  Dear,

  I had a lot of confusion about the ASA with the power of fire all the new features, upgrade, changes made me lost.

  Can someone describes the steps to install the ASA with firepower and upgrade its image & package and the license application. (configuration of the box from scratch).

  What is the best practice for the installation of ASA with firepower in a network?

  TAMÁS is our license what are the features will be important for me, if I want to do a total security. And how about internet proxy I think of ending my TMG Web proxy and use this ASA. I want to use the devices to its full occupancy and all the features that I needed to be activated if necessary.

  How to deal with WLC and the wireless network (which is the best practice for ASA with the firepower and WLC

  Yes maybe that's a lot, but I think many inspiring answers will knock at least with redirection to another topic or some brilliant ideas.

  Kind regards

  Christel

  @mishaal-thabet

  There is a Quick Start Guide to ASA with module power of fire services here:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  In addition, to configure your policies of Management Center of firepower to make the most effective module, I recommend the Cisco Live presentation by 2015: "BRKSEC-2018 migration ASA IPS and CX to firepower." You don't have to worry about the title, it's a good overview for most use cases.

  It can be found here:

  https://www.ciscolive.com/online/connect/sessionDetail.WW?SESSION_ID=836...

  The WLC interact with the ASA directly but the placement of your controller and you use anchor and host controllers can play in your ASA interface design (i.e. comments in an area controllers demilitarized). Other than that, Wireless subnets are just part of the variable "$HOME_NET" located on the module of firepower.

  I hope this helps.

• ASA with firepower and Licensing Service

  Hello

  If I buy an ASA with the power of Fire Service (e.g. 5516-X) should which licenses I buy?

  I understand that I need to order a license for the Service of firepower. E.g. IPS, URLS, and AMP.

  Should I order a license management FireSIGHT, too? The centre of mandatory FireSIGHT management? This license is necessary?

  Concerning

  You will need the license of control (CTRL). It is free and automatically included with any package of power of fire SKU (i.e. ASA5516-FPWR-K9).

  Then you must add the IPS, URLS or AMP (or combination of both) services in term 1, 3 or 5 years.

  FireSIGHT Management Center is not required for entry-level (5506, 5508 or 5516) models. It is optional on those you can use the entry firesight level integrated in ASDM for the model.

  For all other models, it is necessary. If you manage more than a simple ASA (even an HA pair) it is recommended even for the entry level models that you will be so power sync policies through them all.

• ACS 5.2 assignment of authorization with nested groups in LDAP

  I have a Cisco Secure ACS 5.2 on a virtual machine. We use it for administrative access to our equipment Cisco GANYMEDE +. I use LDAP to authenticate with acitive directory. I currently run when a user is directly in the group that is assigned.  I change the way in which assign us group permissions and have created nested groups.

  For example:

  -User1 is a member of group1

  g -roup1 is a member of the "Group 2".

  I have card group2 to have access to my devices. However, User1 is not get mapped to the Group of law and access is denied.

  When I go to the monitoring, reporting and authentication GANYMEDE + details, under other attributes where it shows the outside groups the user is a member, I don't see group2, only group1.

  However when User1 is a member of group2 directly, the user is able to log on.

  GBA 5.2 not does support permissions allow this how to use nested groups?

  Mapping of nested groups is not supported by LDAP (because users containing that attribute memberOf groups just above them, are not nested). It is a behavior deafult when we use nested with LDAP groups. You must add subgroups for GBA and both respective authorization rules.

  Kind regards

  Jousset

  The rate of useful messages-

• ASA with two internet connections

  Hello

  I want to connect an ASA with two ISPS for internet traffic, one for the VPN S2S, there is a router VPN dedicatet on the second link.

  In case of failure of the first link, the second must be enabled.

  route outside 0.0.0.0 0.0.0.0 10.20.20.1 1 track 1route backup 0.0.0.0 0.0.0.0 10.20.30.1 254
  
  route backup 192.168.0.0 255.255.0.0 10.20.30.1
  
  Is this configuration working?? 

  Hello

  You need to configure the 'als' monitor configuration to monitor some destination on the main IP address ISP for the ASA whether the connection works. Probably an IP address on the public network.

  SLA 1 monitor

  type echo protocol ipIcmpEcho outside interface

  NUM-packages

  timeout

  frequency

  SLA monitor Appendix 1 point of life to always start-time now

  You will also need a configuration related to 'track' of the order

  track 1 rtr 1 accessibility

  Route outside 0.0.0.0 0.0.0.0 10.20.20.1 track 1

  Backup route 0.0.0.0 0.0.0.0 10.20.30.1 254

  The above combined with the routes you mention should be enough about the delivery. Naturally for each remote VPN L2L network you will always need a specific static route on the SAA to the backup ISP device.

  Also you must naturally maintain the translations on the SAA. Seems that your ISP links have in mind a separate device that contains public IP addresses. So am I right in assuming you pass all traffic from the LAN links for links to PSI via the ASA without any type of NAT, and leave these routers from the private to the public NAT?

  -Jouni

• Transform a shape layer with several groups/paths in another?

  Hello

  I'm trying to turn the form A B-shaped into aftereffects.

  

  Both are drawn in illustrator, and I imported into aftereffects and diverted path to forms.

  At the moment I do a key framing color and the path in the sticky on the form A and form B. From there I will meet with two questions.

  (1) for now I have to manually open each group, every path, every feature of color until I'm able to keyframe them. After that I have to paste the keyframe of the track and keyframe colors individually to the corresponding group. It's doable, but I have to turn the form in 10 more other variants. Just want to check is there a shorter way to the key all the way to access and color properties frame. And then copy all of the keyframes from one form to the other.

  

  (2) I noticed that not all the points on the path are created equal. I think that the "starting point" is noted with an extra box compared to other points.

  

  As the "starting point" of a path is different from the rest, the transition has become weird.
  Can I check if someone knows how to change the "starting point" to another point on the same path? Or y at - it another way of fixing?

  Finally, if there is more easy morphing shapes to another, I'll be happy to listen. Thanks a lot ~

  I would do this kind of thing differently and 90% of the work in Illustrator.

  I would like to begin by drawing a path in Illustrator, to duplicate the path and to change the size and position and change the color of the outline of the color I wanted for the inside of the first form at the beginning of the animation.

  

  I use then the gradient tool to create a blend between the two forms specifying the number of steps, so my first form duly filled out for one frame looked like this:

  

  I would then do the same for my second form by using different colors, so I got this:

  

  With the two mixtures on you will see this:

  

  The upper mixing layer is where your animation will start and the bottom is where your animation should end.

  The next step is to select Merge layers and spread the mixture, if you find yourself with two groups:

  

  Here comes the fun part. Select groups, and then specify the number of steps you want as long as the number of images that you want in your animation. In this case, I want a second 1 transition and my comp is 29.97 FPS, so I selected 30.

  

  Now spread the mixture:

  

  We should end up with a group at layer 1 with 30 subgroups:

  

  Ungroup the higher group only then deselect all layers and select a single layer, then choose release to layers (sequence).

  

  now select all sub layers in the layer panel and drag it above layer 1. Layer 1 is now empty, so you can delete:

  

  Save the file HAVE and import into AE as a model with the size of the layer keeps selected:

  

  [Open the model, select all layers, move the a CTI frame to the right by pressing Ctrl/Cmnd + arrow to the right, then press Alt/Option +] to set the out point of all layers and then the wizard from keyframe to the layers in sequence without overlapping:

  

  I usually go to the point of exit of the background layer and press N to set the work area exit point, then cut the comp to work area.

  

  This model is then nested in your main comp and you can activate the time-remapping, so you can change the speed and use CC force motion blur to smooth animation.

  

  You will find it much easier to create the morph to a shape layer in Illustrator those in AE, you don't need to convert anything to forms and most of the work is done for you before you start. Total time to create this project with about 1/4 of the time it took to create this post.

• Power CLI script to add multiple VLANs with port group name in an ESX cluster

  Hi all

  Can someone help me get a script adds several VLANs with port group name in an ESX cluster?

  Kind regards

  Suresh

  OK, so you just need to do an Import-Csv inside the loop and change the variables accordingly.

  What is the provision of this CSV file?