IP address of management VMWare ESXi 4.0.0 decline in traffic

Similar Questions

• How will be manage vmware esxi without vmware IC

  I installed vmware esxi, this is a really wonderful app

  use vmware infrastructure client to manage esxi, but it's 60 days trial,

  is there one free another way to manage esxi after expiry of vm IC

  Thanks for your replies

  The VIClient comes free with ESXi, too. Do you have a free license for ESXi? It's probably the ESXi and not the VIClient which expires.

  Kind regards

  Gerrit Lehr

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

• VCenter Server first to 5.5.0U3b update and later update of VMware ESXi ESX / will I have problems?

  Hello

  have trouble when I first updated my signature single vCenter Server and later update my vSphere hosts?

  A vCenter Server Version 5.5.0U3b should be able to manage vSphere Host Version 5.5.0 GA, right?

  Kind regards

  Roland

  The vCenter Server 5.5 update 3 b can manage VMware ESXi ESX release GA to 5.5 5.5 update 3 b, take a look: VMware product interoperability Matrices

  BUT, according to the interoperability matrices and vCenter Server 5.5 update 3 release notes, VMware strongly recommends you upgrade your hosts to 5.5 update 3 b, see:

  What's new

  • Update Support for the SSLv3 Protocol is disabled by default
    Note: In your vSphere environment, you must update vCenter Server vCenter Server 5.5 update 3 b before the update to 5.5 ESXi ESXi update 3 b. vCenter Server will not be able to manage 3B ESXi 5.5 update, if you update ESXi before update vCenter Server to version 5.5 update 3 b. For more information about the sequence in which vSphere environments must be updated, see KB 2057795.

  • VMware strongly recommends you update ESXi hosts to ESXi 5.5 update 3 b management of vCenter Server 5.5 updated 3B.

  VMware does not recommend the reactivation of SSLv3 because of the vulnerability of POODLE. If all you must enable SSLv3, you must activate the SSLv3 Protocol for all components. For more information, see

  KO 2139396

  .

  • Resolved issues. This version of vCenter Server 5.5 update 3 b solves the problems that have been documented in the resolved issues section.

• Cisco ISO Custom - VMWare ESXi 5.5 Upd 2 - VMware Update Manager still shows update 2 required

  Hi all

  I just updated one of my guests with the latest cisco image provided on the vmware website (Vmware-ESXi-5.5.0-2068190-custom-Cisco-5.5.2.3).  After the application as an upgrade of the host and then doing a scan against the host in the Update Manager, it shows that ESXi complete update 2 is missing?

  I know this is maybe more a problem of vmware, but wanted to see if someone had run into this?

  This thank you for the quick response.

• LSI MegaRAID Storage Manager on VMware ESXi 4.0

  Hi guys,.

  We tried to install on VMware ESXi 4.0 MegaRAID Storage Manager (IBM x 3550 M2) and it uses Controller RAID MegaRAID SAS 8808E to monitor the hard disk status but could not be able to install and it returned the error as attaché

  We followed the procedure as shown in the following ibm Web site

  1.6 MegaRAID Manager storage system to a VMWare ESX Server

  Follow these steps to install the on a MegaRAID Storage Manager

  VMWare ESX Server:

  1. download the latest MSM to ibm.com

  2 unzip the and copy MSM_linux_installer - 501.01.tar.gz on a USB key.

  3. from the ESX Server, in the console root, type the following command

  to identify the USB device: fdisk-l

  4. type the following command: mount/mnt/dev / {name of the USB device}

  5. type the following command: cd/mnt

  6. type the following command to copy MSM_linux_installer - 501.01.tar.gz in the occupied Palestinian territories

  file: cp MSM_linux_installer - 501.01.tar.gz / opt

  7. type the following command to decompress the package gunzip MSM_linux_installer - 501.01.tar.gz

  8 type the following command to unzip the package tar - vxf MSM_linux_installer - 501.01.tar

  9. replace the directories with the path/opt/disk

  10 tapez./vmware_install.sh to install MSM

  11. Select version of VMware

  a. enter 1 to install Vmware 3.5

  b enter 2 for VMware 4.0 install

  12. Select the storlib option

  a. Enter n If you want to use the Inbox storlib driver

  b. Enter y if you want to install the storlib delivered with MSM

  IBM recommends 'y' is selected for use packed with MSM, storlib by selecting "n" can

  cause some features of MSM does not function properly

  I would like to know if I use the correct version of the Storage Manager Application MegaRAID for VMware ESXi 4.0

  
  

  If not could someone please advise on how to proceed with the installation and troubleshooting

  Please find the file of errors as attaché

  
  

  Greatly appreciate your help

  
  

  Thanks in advance,

  Vignesh
  

  Check if help: vSphere unknown health status ' vSphere ' eMware »»

• Hot migration is possible with VMWare ESXi 5.1.0 without an ESX server management

  Hot migration is possible with VMWare ESXi 5.1.0 without an ESX server management?
  I wonder for a future issue, a scenario where a system administrator must build a Win2008 + DC on local storage, server
  then, once the physical box is integrated into the class network, the physical box is connected to the classified SAN storage.
  Is it possible to hot - migrate the server Win2008 + CC local storage to SAN storage at this time, with only the
  free version of VMWare ESXi 5.1.0?

  Welcome to the community - I guess that you are looking to do this, while the virtual machine is currently running - this is not possible without a management server, also called vCenetr, but all is not lost because you would be able spend the VM local storage to the San with the VM posered using the client storage management features

• How to configure the IP address on VMWare ESXi 3.5

  Hi all.  I installed the VMWare ESXi 3.5 on a test to dedicate

  Server, assign a private IP = 10.10.1.10 to the VMWare box (this box has 2 physical NETWORK card); and then I

  installed the Symantec BrightMail 9.0.2 as a virtual appliance on VMWare ESXi

  3.5 to act as an e-mail gateway.  BrightMail installation goes smooth.  However, I am not in a position

  to connect to the Internet inside BrightMail 9.  I have installed BrightMail for

  have 2 virtual network card.  Network 1 (eth0) got the IP =

  10.10.1.11, network 2 (eth1) got the IP = 82.132.33.45 (real

  public IP address).  With this settig BrightMail virtual machine is able to talk with the other PC in my LAN, howerver, it can't go on the Internet.  My network configuration is as follows:

  A router (Modem, with the public IP address) is directly connected to the VMware computer (the first NETWORK adapter), and then the VMWare (second NETWORK card) connects to a switch where other LAN PC also connects to.

  My question is,

  1. from BrightMail runs on top of the

  VMWare, how can I BrightMail to connect to the Internet and to the

  Moreover, it connects to my LAN?  Currently the machine has VMWare a

  10.10.1.10 private IP assigned address.

  I'm a bit confuse about the settings of the network on the VMWare itself (I'm not the network

  Guy).  Any suggestion is weclomed.  Thank you.

  the observed range, vmnic0 resembles your DMZ LAN and vmnic1 is your LAN (172.x.x.x) you can check you have the right cable to the correct port?

  then you are supposed not combined two NICs in a single portgroup. you will need to do vmnic0 as a new vswitch with new portgroup named DMZ Lan and change that in the virtual network adapter machine virtual 2 to use the DMZ LAN as the virtual switch.

  iDLE-jAM | SC 2, SC 3 & VCP 4

  If you have found this device or any other answer useful please consider useful or correct buttons using attribute points

• Virutal Center can work next to the Vmware ESXi management package

  Hi all

  VMware currently has a promotion on Vmware ESXi management kit which is basically a Virutal Center Foundation license. That being said if you already have a virtual Center Server for all of your ESX servers could run a 2nd VMware ESXi management kit virtual Center Server for all your ESXi servers in parallel? or they will conflict with each other?

  My understanding is you can run as many virtual servers Center like you license but you can have than 1 ESX Server any attached to 1 Virutal host at any given time.

  We run 7 instances vCenter, so yes it is possible.  In addition, as you said a host ESX (i) can be managed by a single instance of vCenter.

• Path to upgrade VMware ESXi Management Kit

  I am interested in the offer of VMware ESXi Management Kit, but want to know if it will work with our plans for the future. I am particularly interested in the vCenter Foundation to allow us to track the performance of the server.

  At the moment we have an ESXi server and could get a second in the near future. End of the year, however, we plan to invest in standard with HA or possibly Enterprise with VMware vMotion. That we will be able to use the Foundation of this package vCenter in this future configuration? The host licenses are only for ESXi and we will have to buy new ones? If we do not upgrade vCenter or host is a way of evolution at discount prices or we will have to buy new ones?

  Budget is a problem then if we cannot reuse this in our final configuration so I won't be able to justify the cost.

  Thank you.

  vCenter Foundation lets you connect an ESX host 6CPU value.  Is not serious ESXi or ESX.  If you use two connectors boxes, then as soon as you add a 4th host computer, you will need to update your vCenter license.  There is a reference number which allows a foundation upgrade to vCenter Standard.  What it is offhand, I don't know, but your dealer can help you with that.

  In regard to 'free' with vCenter ESXi usage, you can not.  You must register (at least) Foundation for each ESX/ESXi host, you want to manage via vCenter.  Pay the $995 (list price) gets you the "VirtualCenter Agent" that is needed to connect to vCenter.  Note: You can install ESXi, play with it for as long as you want, but once you want to attach to vCenter, you will need the license... but there is No change to the ESXi host... you just load the license file in vCenter and you'll be all set.

  Hope that helps!

• I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC.

  I installed VMware ESXi on my Cisco's UCS server but after that I don't get from CIMC. also, I am unable to ping the address IP of CIMC. Any help?

  I think that MMIC does nothing with your ESXi installation... it is OoB management for servers of the UCS.

  Check your config MMIC inside the BIOS again.

  BR,

  Dragan

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• BB10 Simulator on Vmware ESXi

  I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:

  1. Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
  2. Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.

  At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.

  The next step is to connect the Momentics IDE to this virtual machine.

  The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.

  If I try to connect to the virtual machine by IP address, I need a device password, I did not.

  Someone at - it suggestions on what do I do now?

  In response to my own question because I found the answer:

  Now that I have the IP address, I just follow the steps described in

  http://supportforums.BlackBerry.com/T5/native-development/BB10-native-Cascades-SDK-not-connecting-to...

  Because I had never set up a password for the Simulator, I left the empty password field.

  Copy-paste the details:

  Of your IDE

  -Right click on your project in the Project Explorer

  -Go to Blackberry tools and click on configure target...

  -Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish

  To run your application on the Simulator:

  -In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.

  -Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.

  -In the Project Explorer view, right-click the project and select build project.

  -Right click on the project again, and then select run as > BlackBerry Application C/C++.

• Channel Port LACP with VMWare ESXi IP hash Message: % SW_MATM-4-MACFLAP_NOTIF: < MAC > host in the vlan 1 is flapping between port

  Hello

  Currently I have a VMWare ESXi host with 2 network including 6 cards (3 of each) ports are connected to a X 3750.  I configured LACP on the switch and the Port of vDS group road based on IP Hash (802.3ad), my looks of config as follows:-

  src-dst-ip port-channel load-balance

  Interface Port-channel15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  !

  interface GigabitEthernet1/0/15

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/16

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/17

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/18

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/19

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  !

  interface GigabitEthernet1/0/20

  switchport trunk encapsulation dot1q

  switchport mode trunk

  bandwidth share SRR-queue 10 70 25 5

  form of bandwidth SRR-queue 10 0 0 0

  priority queue

  MLS qos trust dscp

  spanning tree portfast

  channel-protocol lacp

  active in mode channel-group 15

  Currently I see many MAC beat in the log of the switch.  From my understanding, I expect the MAC address out all ports, because that's what'd ESXi when you use 'route based on the hash of the IP.  I'm worried about the impact this might have on the CPU / switch.

  August 6, 09:42:05.700 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  August 6, 09:42:16.479 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.28e4 to host in the vlan 1 is flapping between port gi1/0/20 and 0/article gi1/17

  August 6, 09:42:18.719 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.7f6a to host in the vlan 1 is flapping between port gi1/0/19 and article gi1/0/20

  August 6, 09:42:20.766 TSB: % SW_MATM-4-MACFLAP_NOTIF: 0050.569e.0939 to host in the vlan 1 is flapping between port gi1/0/16 and article gi1/0/15

  Is it by design, if so can I disable the message?  If this isn't the case, please can you advise where I can check/change the configuration?

  Thank you

  Peter

  It is really gud who... .you mentioned your solution here.

  Can you please mark this question as answered, thatâ so it can help the other guys.

  Concerning

  Please rate if this can help.

• Problem with the start of VMware ESXi 5.0

  I just installed VMware ESXi 5.0 on a new Cisco UCS B200 series blade with two 300 GB hard drives configured in a RAID 1 mirror.  I went through and completed the installation of VMware ESXi 5.0 on this server.  When the installation is complete and the server restarted, he did not initiate the ESXi where I can change the IP address and VLAN.  Instead, I get this text string after the initial boot sequence that is shown in the attachment.  I have a guest who said Shell > do not know why I can not start correctly in ESXi 5.0.  Thank you!  Paul

  Hi Paul,.

  Looks like you boot to the EFI shell. What is the startup policy that you have configured on this server service profile? It should look like the one below.  If there is a problem with the boot order, you should be able to type "EXIT", then enter on the EFI shell to exit the prompt. If your startup is similar to the one below and you still experience this issue, try to downgrade and re - ack the blade.

  Let me know if it helps.

  

• Nexus 9396 VPC with VMware ESXi 5.5 switch Standard

  We have just upgraded our central office switch in a Nexus 9396, which is linked to double UCS 6248 FI and also individually to some Dell R710 with dual 10 GB Ethernet card. When it connects to these stand-alone servers with a VPC etherchannel, the IP address of management rises and falls and some hosts can speak while others do not. If I leave a disabled port, it works fine. However, as soon as the two are enabled, connectivity breaks down. These ESXi servers are on a standard license, so distributed switches are out of the question. I have activate eval license and installation a vDS using the LACP improved and that works fine, it just doesn't work as an etherchannel standard with a standard virtual switch. The connectivity of the 6248 works also without any problems running in LACP. Here is the configuration:

  SW01 Nexus:

   interface Ethernet1/5   description ESX vPC Member   switchport mode trunk   channel-group 202   no shutdown interface port-channel202   description ESX   switchport mode trunk   vpc 202 

  SW02 Nexus:

   interface Ethernet1/5   description ESX vPC Member   switchport mode trunk   channel-group 202   no shutdown interface port-channel202   description ESX   switchport mode trunk   vpc 202 

  Configuration of ESXi is a standard switch with "Route based on the IP hash" and the two active adapters. Am I missing something? This configuration is not supported? Any help/advice would be greatly appreciated.

  Thank you!

  What happens if you do not use Portchannel, only 2 10gig (1/5 on each switch)?

  I think that the on the ESX host using maps network HA and can use only a single link. Once an operation fails, it uses it.  I think, I remember because the same problem with ESX hosts a couple of years.

  You can test the redundancy with physical ports and Portchannels?

  HTH