iphone4s (unlock version) may not work after restoring ios9.2

Similar Questions

• Satellite Pro 6100 Wireless does not work after restoring from HARD drive

  After that restore disks for installing a new HD and use and to update XP sp2, the Wireless does not work and if the card is installed XP hangs then works in fits and starts. If the card not in place, not bad at all.

  Booting from a Linux CD, the card works perfectly! I assume that the driver is the problem. The wireless card is the original, an Agere MPC13A-20/R, with Toshiba p/n PA317U-1MPC.

  I have found some drivers Agere, but am not sure

  (1) if they are correct
  (2) how to install since the machine works in a way limited with the card in place.

  Any advice?

  Hello

  I checked the page of the pilot and the only available for Windows XP WLan driver is the driver of v.1.11.108 Agere.

  (1) just try to install this driver. If the driver is not correct or is not compatible, then windows will not install the driver and you will receive a notification. You just have to try

  (2) generally you may reinstall the driver from the Device Manager. Open network controller tree, and then you can reinstall the driver.

  But this is only possible if the windows started successfully

  PS: Have you checked the information of Microsoft Windows XP SP2 update on the page of the Toshiba driver.
  I discovered that you need to update several utilities if you have installed SP2 on this laptop.

• Windows Update does not work after restoring the system

  HP Compaq 6000 Pro, bought in early 2011. Windows 7 32 bit. I recently did a factory restore to return to a clean system using factory restore partition. The restoration seems complete ok, and I have a Windows 7 clean and functional configuration.

  However, the Update window will not work (and of course, it is now quite an old installation of Windows 7) it comes up with the Red Cross and the message "Windows Update cannot currently check for updates because the service is not running." Other notable issues that may or may not be related are: Windows Defender won't start not (0 x 80070564). HP Support Assistant reports it needs to update, but the update fails (because then it just says: it should be updated again)

  What I've tried so far:

  Verified that the BITS and the WU services are both actually run

  Uninstalled the McAfee antivirus software

  Tried to install Windows 7 SP1 directly (happens with "catastrophic failure")

  Tried Windows Update (wusa.exe) stand-alone installation / WU Readiness tool-fail (Oxc8000247)

  MS difficulty he said Troubleshooter it corrects problems, but nothing changes later

  (In short, tried all suggestions from MS support)

  It drives me crazy - any help will be appreciated!

  ISO should work, just be sure to download the version of Pro 32-bit.

• Windows Update does not work after restoring Windows.

  I have a HP Mini 210-2080NR netbook with Windows 7 starter (31-bit). My hard drive failed and I replaced it. I ordered a USB HP recovery and then reloaded Windows 7 on new hard drive using the USB recovery drive.

  After reloading Windows 7, Windows Update does not work.

  This is the error I get:

  Windows Update cannot currently check the updates, because the service is not running. You may have to restart your computer.

  My connection is OK.

  I restarted my netbook and the error is the same.

  I reloaded Windows 7 and the error is the same.

  Any suggestions?

  Thank you

  eknaphus

  Hello

  You can try and install it and check:

  Intel Rapid Storage Technology

  After that it gets installed restart and check again. Let me know if this does not help...

• Monitor does not work after restoring update

  Hello. I have a problem with my PC. My CPU is on but the monitor shows No Signal box. Previously, this problem seems too. But I fixed that by cleaning the RAM access (or other) Point. But this time, this method did not work. I have clear the CMOS, but the problem still not fixed. Oh yes, this problem occurs after the update. When updating, the update has failed and come back. When I start the PC again, nothing is displayed and there is no sound signal. Help me please. My characteristics are processor i3 Intel, ATI Radeon HD 5550 2 GB, DDR3 RAM 2 x 2, Windows 8 Pro 64 Bit.

  Hi Chloe,.

  Thank you for the update.

  I understand that since the DVD burner does not work, you are not able to create installation media.

  Put a USB installation media option. You can use both links to download and create below

  Update Windows with only a product key

  http://Windows.Microsoft.com/en-us/Windows-8/upgrade-product-key-only

  Here are the steps:

  1. download and open the Setup file install Windows 8 Microsoft from the link above.
  2. Enter your product key of Windows 8 and start the download.
  3. once the download is complete, select install by creating media.
  4. Select the USB flash drive (it should be the default choice) and insert the USB key.
  5. accept all prompts to clear the contents of the USB key in order to start the process.

  

  

  

  

  

  Let us know if that helps. Keep us informed so that we can help you further if necessary.

• My router Linksys BEFSR41 (model) 4.2 (version) does not work after I tried

  to update to firmware Ver.2.00.4 Build 5. The power still works, but I can't connect to internet with it more. I pressed reset to 30 seconds and disconnected the power for 5 seconds and restarted my PC and it still does not work. Someone knows how to fix this?

  It won't even show the IP of the gateway by default more when I run the ipconfig command. I can't ping it.

  What IP address you get on your computer?

  Connect the modem to the Internet port and the computer and port Ethernet 1 of the router.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 30 seconds. Power cycle the router and check the IP address of your computer.

  If you get a valid IP address as 192.168.1.xxx then try to ping the 192.168.1.1 IP address.

  If you get the IP address auto-configuration as 169.254.x.x then assign a static IP address on the computer (192.168.1.10 subnet - 255.255.255.0, gateway - 192.168.1.1) and then try to ping the router.

  If you get answers from the router then try to open the router configuration page.

• air2 iPad does not work after update ios9.3

  Hello

  My iPad air2 does not open links Amy in safari or the mailapp after that I upgraded to ios9.3

  I tried a reset, but that did not work.

  There is a section in this troubleshooting article that talks about this problem. Take a peek inside. Something might work for you.

  http://osxdaily.com/2016/03/25/Troubleshooting-iOS-9-3-update-problems/

• Satellite P200D-139: number lock keyboard & num do not work after restoring

  I had to recharge laptop after a windows update created problems.
  After using supplied restore CD locking keyboard and num number no longer work.

  Ideas please

  Hello

  I doubt it has something to do with the new installation of the OS
  I mean its sounds more like a hardware problem and not software problem

  In my opinion, it was a bad luck or chance that happened immediately after the recovery procedure

  But why you said that these buttons don t work?
  Have you tested with different applications?
  What in the update of the BIOS? You have the latest version of the BIOS?
  Have you tried to repeat the recovery procedure? Do it!

  Otherwise I think it might be a keyboard issue and possibly the keyboard must be replaced.

• the Windows Setup program does not work after restoring

  Since I restored my system, when I try to open excel or word, I get a windows install. Even after installing windows install 4.5. How can I get excel and word to work?

  Hello

  1. could you give us the exact error message?
  2. do you get this error only when you use Excel?

  Method 1.
  I recommend you to reregister the Installer engine.
  Here's how:
  a. Click Start, click Accessories and then click command prompt.
  b. at the command prompt, type the following and press ENTER after each line:
   
  MSIExec /Unregister
   
  MSIExec/regserver

  
  Method 2.
  

  It seems that there is a background app that launches the installer of Windows. We can perform a boot minimum troubleshooting to find the same thing. You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  I hope this helps.

• Lightroom 6.5 will not work after restoring the windows 10

  First of all, let me say that Adobe support for a pro user product sucks. Really? no other than this support?

  My windows 10 workstation crashed and did a restore. I understand that it is early and I had to reinstall the update 6.5.

  Problem is that Lightroom does not open because he repeats to me there is problem of catalog and will not allow last backup is only a few days to work.

  Then. How to solve this problem?

  The only thing that worked was completely reinstall Lightroom 6, and then apply the latest update.

  After that, I was able to use the last catalog had been saved.

  You guys seriously need better than this forum support if you want to think of yourself as a product for professional use.

  When all else fails reinstall, but this kind of support, it's not what you need.

  Capture One to become a better alternative if you have a serious problem.

• G560 keyboard does not work after restoring

  Hello!

  I just did a restore using the recovery disks sent to me by the customer hotline of lenovo.

  the whole process went through and now it says:

  "LENOVO PRELOAD IS COMPLETE!

  Press any Key to Shutdown! »

  the keyboard and the touchpad does not, so I can't press a key...

  My question is, do I I just stopped the laptop by pressing the power button or deals that damage the recovery?

  Thank you very much!

  it solved!

  I pressed ctr + alt + delete and then the keyboard worked again and I could press a button...

  Thanks anyway!

• CD/DVD drive does not work after restoring the computer in Vista

  My CD/DVD has stopped working. Now if I boot my computer it crashes just on the main start screen. I have to unplug the power to the drive in order to boot my computer. I've corrected the driver once before but my computer crashed and I had to restore. Now, the problem happened again and I can't find what I did the first time to fix the driver. Help, please.

  http://support.Microsoft.com/kb/982116/en-AU

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  See if the information above solves the problem.

  See you soon

  Mick Murphy - Microsoft partner

• trial version does not work after replacing components on the computer

  I tried to download the trial of 30 days a little back, I ended up needing to replace some parts of my computer and never had to use the trial. I just got my pc to the top and the race and now I can not use the 30 day trial on this pc more. I contacted customer service and they told me that I had to ask the forums because they didn't know what to do. I hope someone can help me solve this problem. Thank you very much

  Customer support should tell you that you are unable to run the trial version after making substantial changes to your computer, such as resetting the clock. You cannot run the trial version on this computer again. If you have another computer (a laptop, for example), you can run it there. Alternatively, you can wait until the next version of Dreamweaver is released. You should be able to run the test from a different version.

  No announcement has been made on a new version of Dreamweaver, but it's almost a year since the last major version, so it might be pretty quickly.

• Create product recovery media does not work after restoring to factory settings

  Updated my T500 from 160 to 320 GB.

  First of all, ran the RnR restore to factory settings with the product recovery media that I made earlier. And then restored my C: volume from my Windows Home Server backup.

  Everything seems as usual except my service partition is now f: instead of S: and my Lenovo partition is H: instead of q:-I tested it I can get into the RnR with F11 service partition.

  But when I try to create new recovery media product the ICT box is grayed out on the first prompt so I can't continue. Put back the partition of Lenovo on q: in disk management has not changed anything, he would let me change the letter of the service partition.

  It's no big deal - I still have my original disks - but it would be good to know what I could improve for the next time I have to do a restore.

  Think that I thought about it - when I restored my C volume I also restored a version of RnR who 'knows' I already burned disks. So next time if I want to burn new disks, I need to do on the version of the system factory setting before you restore the volume C:.

• Re: WIRELESS does not work after restoring the system to the factory settings

  Hello

  I just had to reset my Toshiba Windows 7 laptop to factory settings, I backed everything up to an external hardrive beforehand. After the process that kept restarting my laptop on its own, he did this, while the default Toshiba program was missing (from the application of the box). He said not to interrupt or turn off the PC while it was running, but I couldn't stop it do it several times. The process finally ends the green bar hit 39/39 and let me come back to the office.

  It seems to be OK now, but I can't get online, I have connected to my wireless router and it says connected with an excellent signal but I can't do anything on Internet Explorer. I would like to re - download a few things such as Adobe Flash Player, AVG Free, Mozilla Firefox but can't even get anything. It's not even an error message that appears when I'm on IE.

  Can someone help me please?

  Tommy

  I hope that you can use your laptop by using the LAN connection.
  Have you tried to reboot your router?