IPSEC VPN on ASA5505

Hello, hope you can help me:

I need to configure an IPSEC VPN on an ASA5505, with one. PFX certificate to authenticate with the VPN endpoint. I can install the certificate as a certificate authority, but when I use the VPN Site - to - Site Wizard, I put the IP address peer, afterI try to select the certificate that is downloaded, but when I click on the name of the certificate, there is no certificate

I don't I can solve this problem?

Thanks to all in advance

Hello

Do you see the certificate imported as cert ID? If so, you can follow this guide

http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

HTH

Averroès.

Tags: Cisco Security

Similar Questions

IPSEC VPN - no DHCP

I have an asa 5505 connected to another asa in the main site. the ipsec vpn is established and on the side of a remote client, I can use a static IP of this subnet addreess and browse the web and access and ping with the main site inside response.

However, I can't receive any ip from the dhcp server, even if it is enabled on the asa 5505. If I put in a static IP address all right, but that's not realistic. Here is the config on the 5505. Thank you.

ASA Version 9.1 (4)
!
ASA5505 hostname
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
Description of Access Point
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.25.40.200 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 15.15.15.35 255.255.255.0
!
boot system Disk0: / asa914 - k8.bin
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_10.25.40.0_24 object
10.25.40.0 subnet 255.255.255.0
the object of the 10.0.0.0 network
subnet 10.0.0.0 255.0.0.0
network of 10.1.0.0 object
10.1.0.0 subnet 255.255.0.0
access extensive list ip 10.25.40.0 inside_nat0_outbound allow 255.255.255.0 any
Inside_access_in of access allowed any ip an extended list
Inside_access_in list extended access permit icmp any one
access extensive list ip 10.25.40.0 outside_cryptomap allow 255.255.255.0 any
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NETWORK_OBJ_10.25.40.0_24 NETWORK_OBJ_10.25.40.0_24 Shared source (indoor, outdoor) destination NAT static 10.1.0.0 10.1.0.0 route no-proxy-arp-search
Route outside 0.0.0.0 0.0.0.0 15.15.15.3. 1
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 10.1.0.0 255.255.255.0 inside
http 10.1.11.0 255.255.255.0 inside
http 10.25.40.0 255.255.255.0 inside
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
peer set card crypto outside_map 1 15.15.15.3.250
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
management-access inside
vpnclient Server 15.15.15.3.250
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
L2TUN vpnclient vpngroup password
vpnclient L2LVPN username password
dhcpd outside auto_config
!
dhcprelay Server 10.1.0.1 outside
dhcprelay allow inside
dhcprelay setroute inside
time-out of 60 dhcprelay
a basic threat threat detection
threat detection statistics
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
attributes of Group Policy DfltGrpPolicy
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
GroupPolicy_15.15.15.3 group policy. internal
GroupPolicy_15.15.15.3 group policy. attributes
VPN-tunnel-Protocol ikev1, ikev2
tunnel-group 15.15.15.3. type ipsec-l2l
tunnel-group 15.15.15.3. IPSec-attributes
IKEv1 pre-shared-key
remote control-IKEv2 pre-shared-key authentication
pre-shared-key authentication local IKEv2
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
type of policy-card inspect scansafe https-pmap
parameters
httpstraffic of group by default
HTTPS
Policy-map global_policy
CFS-http-class description
class inspection_default
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
inspect the tftp
Review the ip options
type of policy-card inspect scansafe cws_https-pmap
parameters
httpstraffic of group by default
HTTPS
type of policy-card inspect scansafe cws_http_pmap
parameters
httptraffic of group by default
http
type of policy-card inspect scansafe http-pmap
parameters
httptraffic of group by default
http
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
: end
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history

I did have to do it myself, but a message on this site (link) describes how we can make it work.

Unfortunately you will have to static NAT to 1-1 for address outside your local site, but in your case, this interface is itself dedicated DHCP.

Another solution would be to run a DHCP server on the itself 5505 vs relay on your primary DHCP server.

Site to site VPN router-ASA5505

Hello

I have a problem with the VPN between ASA5505 and 3825 router.

behind the ASA, we have a server that serves the specific port. If for any reason any link is disconnected assets if the VPN will become not we do not generate traffic to this server. After generating even a ping VPN immediately become active and communication starts. another case is when you reboot ASA the VPn is not created without ping server behind this ASA.

How we could solve this problem without sending a traffing who serve?

How remote access to this ASA, I can access internal interface? If I open access on port 443 on the external interface of asa could I access it? or I must also exclude this traffic VPN

I used the VPN Wizard to configure on asa and CLI on router

some troubleshootingand configuration commands, if this is not enough please let me know what you otherwise.

Thanks in advance for your help

ciscoasa # sh crypto isakmp his

ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 1

1 peer IKE: 10.10.10.1
Type: L2L role: initiator
Generate a new key: no State: AM_ACTIVE

Configuration of the SAA.

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs Group1
card crypto outside_map 1 set counterpart 10.10.10.1
map outside_map 1 set of transformation-ESP-DES-MD5 crypto
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400

the main router configuration

crypto ISAKMP policy 1
preshared authentication
!
crypto ISAKMP policy 5
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 10
preshared authentication
Group 2
crypto ISAKMP key 6 _JQfe [BeRGNBCGfbGxxxxxxxxx address 10.10.10.10

Crypto ipsec transform-set esp - esp-md5-hmac xxxxx

ETH0 2696 ipsec-isakmp crypto map
defined peer 10.10.10.10
Set transform-set xxxxx
match address 2001

access-list 2001 permit ip any 192.168.26.96 0.0.0.7

Post edited by: adriatikb
I just read somewhere that might change the type VPN "bi-direcitonal' two 'initiator' or 'answering machine' could help me but I test and no results.

I had the same problem last week, and told the TAC engineer on our service ticket downgrade from IOS 8.2 (3) 8.2 (1). Since then, it works fine.

2811: connecting two VPN l2l ASA5505

Hello

We have a HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 with an established ipsec VPN l2l.

I'm trying to connect a 2nd ASA, but I noticed that I only add 1 cryptomap to the external interface.

A worm watch 1 Module of virtual private network... Surely this does not mean only 1 VPN?

Can I use a card encryption and add a second "peer set" & "corresponds to" address inside the card Cryptography itself?

Thank you

Jason

Yes, you add another poicy to your configuration encryption.

Thank you

Tarik Admani
* Please note the useful messages *.

integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

Hello

I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

Please help me, I need my VPN Thx a lot

I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

WRV200 ipsec VPN

Hi guys,.

Tried to set up an ipsec VPN LAN - LAN between my WRV200 and WRVS4400N my companion. Filled all the relevant config... simple... but still nothing. They don't seem to connect. We are both on ADSL and using IP address by DNS. Routers are in the log file and try to establish the connection. Tried all the setting, both routers are configured the same. STILL NO JOY! Can anyone help, before having to migrate to a netgear or something nasty!

Sorry forgot to mention, using an AM200 modem in Bridge mode. It my router DHCP address direct WAN instead of NAT. The two systems are fixed the same where routers have outside the WAN address. The modem is transparent. I guess that NAT traversal in not required in that State.

IPSec VPN to asa 5520

Hello

First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

and this, in the journal of customer:

Cisco Systems VPN Client Version 5.0.02.0090

Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 5.1.2600 Service Pack 3

24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

Start the login process

25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "213.94.x.x".

27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

Attempts to establish a connection with 213.94.x.x.

28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

IPSec driver started successfully

30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

Retransmit the last package!

36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

Set indicator established tunnel to register to 0.

42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

IPSec driver successfully stopped

I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

Can you see what I'm doing wrong?

Thank you

Sam

Pls add the following policy:

crypto ISAKMP policy 10

preshared authentication

the Encryption

md5 hash

Group 2

You can also run debug on the ASA:

debugging cry isa

debugging ipsec cry

and retrieve debug output after trying to connect.

IPSec vpn - no selected proposal

Hello:

I am facing a problem in the configuration of the ipsec vpn on my 7200 router. It's a site to customer topology as shown below.

The request from my pc, R2' isa crypto log:

R2 #debug crypto isakmp
Crypto ISAKMP debug is on
R2 #.
R2 #.
R2 #.
* 22:41:59.871 6 April: ISAKMP (0): received 66.66.66.52 packet dport 500 sport 500 SA NEW Global (N)
* 22:41:59.879 6 April: ISAKMP: created a struct peer 66.66.66.52, peer port 500
* 22:41:59.879 6 April: ISAKMP: new created position = 0x67E98D84 peer_handle = 0 x 80000002
* 22:41:59.883 6 April: ISAKMP: lock struct 0x67E98D84, refcount 1 to peer crypto_isakmp_process_block
* 22:41:59.887 6 April: ISAKMP: 500 local port, remote port 500
* 22:41:59.891 6 April: ISAKMP: (0): insert his with his 67E5DCD8 = success
* 22:41:59.911 6 April: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
* 22:41:59.911 6 April: ISAKMP: (0): former State = new State IKE_READY = IKE_R_MM1

* 6 April 22:41:59.931: ISAKMP: (0): treatment ITS payload. Message ID = 0
* 6 April 22:41:59.935: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.939: ISAKMP: (0): IKE frag vendor processing id payload
* 6 April 22:41:59.939: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.943: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
* 22:41:59.947 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
* 6 April 22:41:59.947: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.951: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
* 6 April 22:41:59.955: ISAKMP: (0): provider ID is NAT - T v2
* 6 April 22:41:59.959: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.959: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
* 6 April 22:41:59.963: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.967: ISAKM
R2 #P: (0): provider ID seems the unit/DPD but major incompatibility of 241
* 6 April 22:41:59.971: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.971: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
* 6 April 22:41:59.975: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:41:59.979: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
* 22:41:59.983 6 April: ISAKMP: (0): pair found pre-shared key matching 66.66.66.52
* 6 April 22:41:59.987: ISAKMP: (0): pre-shared key local found
* 22:41:59.987 6 April: ISAKMP: analysis of the profiles for xauth...
* 22:41:59.991 6 April: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 10
* 22:41:59.995 6 April: ISAKMP: AES - CBC encryption
* 22:41:59.995 6 April: ISAKMP: keylength 256
* 22:41:59.999 6 April: ISAKMP: SHA hash
* 22:41:59.999 6 April: ISAKMP: unknown group of DH 20
* 22:41:59.999 6 April: ISAKMP: pre-shared key auth
* 22:42:00.003 6 April: ISAKMP: type of life in seconds
* 22:42:00.003 6 April: ISAKMP:
R2 # life expectancy (IPV) 0 x 0 0 x 0 0 x 70 0x80
* 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
* 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
* 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 2 against the policy of priority 10
* 22:42:00.011 6 April: ISAKMP: AES - CBC encryption
* 22:42:00.011 6 April: ISAKMP: keylength 128
* 22:42:00.011 6 April: ISAKMP: SHA hash
* 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group unknown 19
* 22:42:00.011 6 April: ISAKMP: pre-shared key auth
* 22:42:00.011 6 April: ISAKMP: type of life in seconds
* 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
* 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
* 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
* 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 3 against the policy of priority 10
R2 #r 6 22:42:00.011: ISAKMP: AES - CBC encryption
* 22:42:00.011 6 April: ISAKMP: keylength 256
* 22:42:00.011 6 April: ISAKMP: SHA hash
* 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
* 22:42:00.011 6 April: ISAKMP: pre-shared key auth
* 22:42:00.011 6 April: ISAKMP: type of life in seconds
* 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
* 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
* 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
* 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 4 against the policy of priority 10
* 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
* 22:42:00.011 6 April: ISAKMP: SHA hash
* 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
* 22:42:00.011 6 April: ISAKMP: pre-shared key auth
* 22:42:00.011 6 April: ISAKMP: type of life in seconds
* 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
* 22:42:00.011 6 April: ISAKMP: (0): offered hash algorithm is
R2 # does not match policy.
* 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
* 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform against the policy of priority 10 5
* 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
* 22:42:00.011 6 April: ISAKMP: SHA hash
* 22:42:00.011 6 April: ISAKMP: group by default 2
* 22:42:00.011 6 April: ISAKMP: pre-shared key auth
* 22:42:00.011 6 April: ISAKMP: type of life in seconds
* 22:42:00.015 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
* 22:42:00.019 6 April: ISAKMP: (0): offered hash algorithm does not match policy.
* 22:42:00.023 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 0
* 22:42:00.023 6 April: ISAKMP: (0): no offer is accepted!
* 6 April 22:42:00.027: ISAKMP: (0): phase 1 SA policy is not acceptable! (local 180.180.0.130 remote 66.66.66.52)
* 22:42:00.027 6 April: ISAKMP (0): increment the count of errors on his, try 1 of 5: construct_fail_ag_init
* 6 April 22:42:00.027: ISAKMP: (0): has no
R2 #construct AG information message.
* 6 April 22:42:00.027: ISAKMP: (0): lot of 66.66.66.52 sending my_port 500 peer_port 500 (R) MM_NO_STATE
* 22:42:00.027 6 April: ISAKMP: (0): sending a packet IPv4 IKE.
* 22:42:00.031 6 April: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 22:42:00.035 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): IKE frag vendor processing id payload
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
* 22:42:00.039 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
* 6 April 22:42:00.039: ISAKMP: (0): provider ID is NAT - T v2
* 6 April 22:42:00.039: ISAKMP: (0)
R2 #: load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 241
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
* 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
* 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
* 22:42:00.039 6 April: ISAKMP (0): action of WSF returned the error: 2
* 22:42:00.039 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
* 22:42:00.039 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

* 22:42:00.059 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
* 22:42:00.059 6 April: ISAKMP: unlock counterpart struct 0x67E98D84 for isadb_m
R2 #ark_sa_deleted (), count 0
* 22:42:00.067 6 April: ISAKMP: delete peer node by peer_reap for 66.66.66.52: 67E98D84
* 22:42:00.071 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 22:42:00.075 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_DEST_SA

* 22:42:00.087 6 April: ISAKMP: (0): removal of HIS right State 'No reason' (R) MM_NO_STATE (post 66.66.66.52)
* 22:42:00.087 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_ERROR
* 22:42:00.087 6 April: ISAKMP: (0): former State = new State IKE_DEST_SA = IKE_DEST_SA

* 22:42:00.895 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
* 22:42:02.911 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
R2 #.
* 22:43:00.087 6 April: ISAKMP: (0): serving SA., his is 67E5DCD8, delme is 67E5DCD8
R2 #.

And when I capture on my pc, I got:

I don't know why, waiting for you helps nicely, thank you very much!

I think that what is wrong is your combination of your group of encryption, hashing and dh, try changing your sha instead of md5 hash table.

Routing access to Internet through an IPSec VPN Tunnel

Hello

I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.

I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.

Any help would be greatly appreciated.

Thank you.

Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.

SA520 and Question IPSec VPN RVS4000

Hello

I installed an IPSec VPN for one of my friends for his company. At its principal office, I installed a Cisco SA520 and he uses to connect devices such as the iPhone and iPad via the IPSec VPN. He uses this fact because he travels abroad a lot and he has problems with services such as Skype is blocked in some countries. This configuration works very well.

It also has a Cisco RVS4000, which he would like to install at his place of business to the Mexico. He would like the RVS4000 VPN configuration to the SA520 in his office. The SA520 in his office has a static IP address. The RVS4000 to the Mexico does not work.

Is it possible to Setup IPSec VPN between a SA520 with a static IP and RVS4000 address that does not have a static IP address? If so, examples of configuration would be greatly appreciated.

Thank you!

Hi William, simply sign up for a dyndns account or similar service, the RVS4000 configuration will be the same, instead of the IP, you'd be using the dyndns name.

-Tom
Please mark replied messages useful

Is availble for IPsec VPN FOS 6.3 support stateful failover

Is availble for IPsec VPN FOS 6.3 support stateful failover

SAJ

Hello Saj,

Unfortunately not... stateful failover replica information such as:

Table of connection TCP, udp xlate table ports, h.323, PAT port allocation table...

they replicate data such as:

user authentication (uauth) table

Table ISAKMP / IPSEC SA

ARP table

Routing information

Therefore, in the case where the main breaks down, the IPSEC vpn will be reformed for the failover... Meanwhile, the user will not be able to access the applications...

I hope this helps... all the best... the rate of responses if deemed useful...

REDA

ISA500 site by site ipsec VPN with Cisco IGR

Hello

I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

But without success.

my config for openswan, just FYI, maybe not importand for this problem

installation of config

protostack = netkey

nat_traversal = yes

virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

nhelpers = 0

Conn rz1

IKEv2 = no

type = tunnel

left = % all

leftsubnet=192.168.5.0/24

right =.

rightsourceip = 192.168.1.2

rightsubnet=192.168.1.0/24

Keylife 28800 = s

ikelifetime 28800 = s

keyingtries = 3

AUTH = esp

ESP = aes128-sha1

KeyExchange = ike

authby secret =

start = auto

IKE = aes128-sha1; modp1536

dpdaction = redΘmarrer

dpddelay = 30

dpdtimeout = 60

PFS = No.

aggrmode = no

Config Cisco 2821 for dynamic dialin:

crypto ISAKMP policy 1

BA aes

sha hash

preshared authentication

Group 5

lifetime 28800

!

card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

!

access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

!

Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

crypto dynamic-map DYNMAP_1 1

game of transformation-ESP-AES-SHA1

match address 102

!

ISAKMP crypto key address 0.0.0.0 0.0.0.0

ISAKMP crypto keepalive 30 periodicals

!

life crypto ipsec security association seconds 28800

!

interface GigabitEthernet0/0.4002

card crypto CMAP_1

!

I tried ISA550 a config with the same constelations, but without suggesting.

Anyone has the same problem?

And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

I can successfully establish a tunnel between openswan linux server and the isa550.

Patrick,

as you can see on newspapers, the software behind ISA is also OpenSWAN

I have a facility with a 892 SRI running which should be the same as your 29erxx.

Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

Here is my setup, with roardwarrior AND 2, site 2 site.

session of crypto consignment

logging crypto ezvpn

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

lifetime 28800

!

crypto ISAKMP policy 2

BA 3des

md5 hash

preshared authentication

Group 2

lifetime 28800

!

crypto ISAKMP policy 3

BA 3des

preshared authentication

Group 2

!

crypto ISAKMP policy 4

BA 3des

md5 hash

preshared authentication

Group 2

!

crypto ISAKMP policy 5

BA 3des

preshared authentication

Group 2

life 7200

ISAKMP crypto address XXXX XXXXX No.-xauth key

XXXX XXXX No.-xauth address isakmp encryption key

!

ISAKMP crypto client configuration group by default

key XXXX

DNS XXXX

default pool

ACL easyvpn_client_routes

PFS

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

!

dynamic-map crypto VPN 20

game of transformation-FEAT

market arriere-route

!

!

card crypto client VPN authentication list by default

card crypto VPN isakmp authorization list by default

crypto map VPN client configuration address respond

10 VPN ipsec-isakmp crypto map

Description of VPN - 1

defined peer XXX

game of transformation-FEAT

match the address internal_networks_ipsec

11 VPN ipsec-isakmp crypto map

VPN-2 description

defined peer XXX

game of transformation-FEAT

PFS group2 Set

match the address internal_networks_ipsec2

card crypto 20-isakmp dynamic VPN ipsec VPN

!

!

Michael

Please note all useful posts

Problem with IPSec VPN ISA500 & login questions (multiple devices)

I have a Cisco ISA500, we use for connection with IPSEC VPN of some products apple (MacBook Pro and iPad). We can operate randomly once in a while, but it fails most of the time of negotiation. Someone at - it suggestions on what I can do to make this work?

I did test it on my Linux machine and it does not when I had configured default settings. I had to change the NAT Traversal for UDP CISCO on the Linux machine for the connection to work.

14/04/03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
2014-04-03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Dead Peer Detection]; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Cisco-Unity]; (pluto)
2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [XAUTH]; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute. Attribute OAKLEY_KEY_LENGTH. (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Dead Peer Detection]; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Cisco-Unity]; (pluto)
2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [XAUTH]; (pluto)

Hi rich,

What version of firmware you used before upgrade? You upgrade to 1.2.19 and now this works?

Thank you

Brandon

Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

Hi all

I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941. I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here. Have I not IOS bad? I thought that a picture of K9 would do the trick.

Any suggestions are appreciated

That's what I get:

Router (config) #crypto?
CA Certification Authority
main activities key long-term
public key PKI components

SEE THE WORM

Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Updated Thursday, March 10, 10 22:27 by prod_rel_team

ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

The availability of router is 52 minutes
System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
Last reload type: normal charging
Reload last reason: reload command

This product contains cryptographic features...

Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
Card processor ID FTX142281F4
2 gigabit Ethernet interfaces
2 interfaces Serial (sync/async)
Configuration of DRAM is 64 bits wide with disabled parity.
255K bytes of non-volatile configuration memory.
254464K bytes of system CompactFlash ATA 0 (read/write)

License info:

License IDU:

-------------------------------------------------
Device SN # PID
-------------------------------------------------
* 0 FTX142281F4 CISCO1941/K9

Technology for the Module package license information: "c1900".

----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
-----------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
security, none none none
given none none none

Configuration register is 0 x 2102

You need get the license of security feature to configure the IPSec VPN.

Currently, you have 'none' for the security feature:

----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
-----------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
security, none none none
given none none none

Here is the information about the licenses on router 1900 series:

http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html

IP address of the IPSec VPN client did not get distributed via EIGRP

We use an ASA for VPN remote access. He is running EIGRP redistribute static routes. When a client Anyconnect SSL connects, the SAA creates a static route for this client, and it gets redistributed via EIGRP. When an IPSec VPN client connects, the SAA creates a static route for this customer, but he isn't redisributed via EIGRP and so the client can not achieve anything. Why he would distribute a static created by an IPSec client?

Thank you

Have you set up IPP on dynamic Cryptography?

IPSEC VPN on ASA5505

Similar Questions

Maybe you are looking for