IPTV/Multicast via VPN

Similar Questions

• Customer multicast via vpn traffic

  Hi guys,.

  Then. I have already created a vpn server on my router 878... while I can connect to this router and the network with ip - sec (cisco vpn client)...

  Al works fine... but... when I also want to allow multicast on my vpn connection traffic. should I then a vpn free WILL? or what?

  What is only necessary when you use a site to site vpn... ?

  And how to activate it?

  Thanksssss

  There is no way we can send directly via remote access VPN tunnel multicast traffic.

• Cannot connect remotely via VPN since installing the new modem/router

  Can anyone help please. Since the acquisition of a new router / modem I can no longer connect via VPN to my work PC remotely. It comes in I receive the error message. Can someone tell me if I need to change the settings for the new modem / router to access?

  

  Hello Joanna,

  Here are the steps you need to do first:

  1. Off static IP for my server and let the router assign IP address and changed the IP address of the port forward.
  2. Check the IP address because obviously, that changed when you plugged into the router again.
  3. Updated to the latest firmware for the router and NIC.

  For more detailed troubleshooting you can refer to this link: troubleshooting common VPN related errors.

  Let us know how it goes.

• Programmatic access to remote files via VPN on Playbook

  Hello

  It is technically possible to download remote files via VPN programmatically?

  I can't find any documentation on this topic.

  Thank you

  Oh, not... I don't think it's possible.

• Check sensor SFR with FireSight via VPN - does not work

  Hello security experts.

  I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor.

  Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN?

  The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem?

  Thank you very much!

  Remi

  Hello

  If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then.

  Can try you to ping from sensor to DC:

  ping -M do -c 20 -s 1572 

  By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works. See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere. Best regards, Aastha Bhardwaj rate if this is useful!

• ASA5505 management via VPN/Anyconnect without group

  I have 2 questions about the configuration of the SAA.

  The first is related to the SSL VPN configuration. Just one group of users to which you connect to our main office via remote access. Is there a way to configure SSL VPN to not display a group selection?

  I have the omission of the list of the groups-tunnel-enable command and configuration group on user accounts locking, but neither work.

  Secondly, I am at a loss on how to configure ssh to allow users connected via VPN connections. I guess:

  SSH 172.16.1.0 255.255.255.0 inside

  with 172.16.1.0 24 is the ip pool assigned to remote access vpn users would do so, however, it's a no go. How can users of remote access (which are for the most part, all technicians) granted the possibility to connect to the device?

  Thanks for your help.

  To be able to manage the ASA via SSH via a VPN tunnel, you will need to enter the configuration command "in man".

• Is VLAN via VPN possible with any of the Small Business routers?

  A tagged VLAN (for voice) will be routed through a VPN gateway to gateway on any of the Small Business routers, such as the SA520? This router is equipped

  Parameters of VLAN Trunking.

  No, it is not possible to send traffic to vlan via VPN on a series of SA500, but you can create a tunnel for each subnet, you need to pass traffic.

  hope this helps,

  Jasbryan

• If a PC with a DHCP server is connected via VPN, with her serve IP addresses on the tunnel?

  Situation: we have a few portable computers test Ubuntu running DHCP servers.  We need get the updates and other changes in corporate network sometimes.  Today, we turn off the DHCP server, set up to get an IP via DHCP (besides) and make our updates.

  Problem: we do not want someone accidentally connect the laptop to the corporate network, while its DHCP server is running.

  Question: so, if we go via wifi using a Cisco VPN client, the DHCP server IP addresses above the tunnel?

  Thanks for reading.

  N ° DHCP uses layer 2 broadcasts to disseminate IP addresses.  Because your clients are connected via VPN, there is no contiguity of layer 2.  The only way he would accidentally do it is if you have configured an address to support IP dhcp as one of your VPN clients on the network, which I imagine you wouldn't.

• Customer remote cannot access the server LAN via VPN

  Hi friends,

  I'm a new palyer in ASA.

  My business is small. We need to the LAN via VPN remote client access server.

  I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.

  Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.

  Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.

  Who can help me?

  Thank you very much.

  The following configuration:

  ASA Version 7.0(7)
  
      !
  
      hostname VPNhost
  
      names
  
      dns-guard
  
      !
  
      interface Ethernet0/0
  
      nameif outside
  
      security-level 10
  
      ip address 221.122.96.51 255.255.255.240
  
      !
  
      interface Ethernet0/1
  
      nameif inside
  
      security-level 100
  
      ip address 192.168.42.199 255.255.255.0
  
      !
  
      interface Ethernet0/2
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      !
  
      interface Management0/0
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      management-only
  
      !
  
      ftp mode passive
  
      dns domain-lookup inside
  
      access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
  
      access-list allow_PING extended permit icmp any any inactive
  
      access-list Internet extended permit ip host 221.122.96.51 any inactive
  
      access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
  
      access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
  
      access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
  
      access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
  
      pager lines 24
  
      mtu outside 1500
  
      mtu inside 1500
  
      ip local pool testpool 192.168.43.10-192.168.43.20
  arp timeout 14400
  
      global (outside) 1 interface
  
      nat (inside) 0 access-list VPN
  
      nat (inside) 1 access-list PAT_acl
  
      route outside 0.0.0.0 0.0.0.0 221.122.96.49 10
  
  
      username testuser password 123
  
      aaa authentication ssh console LOCAL
  
      aaa local authentication attempts max-fail 3
  no sysopt connection permit-ipsec
  
      crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
  
      crypto dynamic-map dyn1 1 set transform-set FirstSet
  
      crypto dynamic-map dyn1 1 set reverse-route
  
      crypto map mymap 1 ipsec-isakmp dynamic dyn1
  
      crypto map mymap interface outside
  
      isakmp enable outside
  
      isakmp policy 1 authentication pre-share
  
      isakmp policy 1 encryption des
  
      isakmp policy 1 hash md5
  
      isakmp policy 1 group 2
  
      isakmp policy 1 lifetime 86400
  
      isakmp nat-traversal  3600
  
      tunnel-group testgroup type ipsec-ra
  
      tunnel-group testgroup general-attributes
  
      address-pool testpool
  
      tunnel-group testgroup ipsec-attributes
  
      pre-shared-key *
  
      telnet timeout 5
  ssh timeout 10
  
      console timeout 0
  : end
  

  Topology as follows:

  

  Hello

  Configure the split for the VPN tunneling.

  1. Create the access list that defines the network behind the ASA.

     ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0 

  2. Mode of configuration of group policy for the policy you want to change.

     ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#

  3. Specify the policy to split tunnel. In this case, the policy is tunnelspecified.

     ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified 

  4. Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.

     ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List 

  5. Type this command:

     ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes 

  6. Associate the group with the tunnel group policy

     ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn 

  7. Leave the two configuration modes.

     ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#

  8. Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.

  Kind regards
  Abhishek Purohit
  CCIE-S-35269

• Help blocking smart devices of via VPN

  Hello

  I am looking for a solution block smart devices to connect to our network via VPN. Our VPN solution today is ASA5520, and we use Cisco ACS to authenticate the user. We use Cisco VPN client only, no anyconnect or SSL VPN.

  Managment is looking for a way that we can stop the smart devices of using VPN clients to connect and allow only desktop computers laptops to connect.

  Someone at - there a way we can do this through association or another method?

  Worring - I block iPhones & iPad around my overall networkwith 100% accuracy with a few simple lines of config: -.

  Group Policy <> attributes

  client-access-rule 1 deny version of type 'iPhone OS. "

  2-client-access rule allow type * version *.

  As it actually works on the OS - not the version of the Cisco VPN Client device.

• How to implement a local SOA/BPM project using remote resources via VPN

  Hello world

  Sorry for the dummy question, but I am a beginner and I'm in trouble with this problem.

  This is the scenario: I have to carry a BPM project using JDev 11.1.1.7 on my local environment and then deploy them on remote servers via VPN where a development environment is configured.

  All services are on remote servers.

  My question is: what I put up in my local environment?

  1 DB connection (distance connettion)

  2 configuration of MDS to share components?

  3 WebLogic server?

  3. what else?

  Any link o idea to share?

  Thank you.

  Fairlie

  Hello

  If you need to deploy and test in your front room to deploy remotely, then you will need to set up all the people in your premises + SOA Suite... If you need to do is put on your local, but can check remotely, you only JDev and connections...

  See you soon,.

  Vlad

• Financial reports - 11.1.2.1 client - connects via VPN only?

  Hello
  
  When I'm directly connected to the network or connected via their intranet wireless, I can connect to fin reports customer of Studio. However, if I train via VPN (Juniper), he returns with a message: you are not authorized to access. Please contact your system administrator. It is a mistake to end too many reports? Any ideas why/how this could happen?

  It is possible that your VPN is not open ports that you can use EN Studio.

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• Mailing address: cannot send mail via VPN

  I use OS X 10.11.3 El Capitan and Mail 9.2

  Whenever the computer is connected via the PIA VPN, Mail cannot send e-mail messages.  Is there a work around for this problem?  Please, let me know.  Thank you!

  There's not enough information here to determine what the problem is.

  If you use one of the many VPN services allows you to hide your activity (supposedly), it is quite possible that your email provider has locked their servers to avoid spam being sent back by criminals who often use these VPNS.

  What does your email provider say when contacts you and reported the problem.

• How to get tickets Kebores initializtion via VPN

  How to get the ticket of Kebores initializtion via the VPN for Single Sign on

  Hello

  The question you have posted is related to a virtual private network and would be better suited to the TechNet community.
  Please visit the link below to find a community that will provide the support you want.
  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

  I hope this helps.

• How to bind a VPN (TX via VPN) with a sat (RX via DVB - S2) / Windows Vista Home Edition / Multiple dial conections

  I use a Windows Vista Home Edition on a laptop. The system connects to the Internet through a cellular router EDGE (via Ethernet) and receives the data by linking receiver DVB - S2 satellite broadband connected via a USB interface. The connection is through a VPN. Windows Vista loses the symbol of the "blue planet", as soon as the VPN connects. Authentication and connectivity is OK. DNS also works OK by the way VPN, with pointing to the VPN IP address 0.0.0.0.  The diagnosis indicates an error where Vista says that she finds multiple active dial connections. Y at - it a configuration option that allows me to bind the interface transmission (VPN) with return channel satellite?  The same software and configuration under Windows XP SP3 works OK.

  Thanks in advance for your advice.

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Forum. You can follow the link to your question:
  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  You can also check the links below for assistance.

  http://TechNet.Microsoft.com/en-us/library/cc728078 (WS.10) .aspx

  http://TechNet.Microsoft.com/en-us/library/cc737767 (WS.10) .aspx

  Hope that helps.