Is there a command line method "add a network location"?

Similar Questions

• Help - best practices or guide line to add additional network cards.

  Hello...

  I seem to have a problem with adding additional network adapters in the ESX 3.5 servers.

  2 x patches up-to-date ESX Server 3.5 and HA Enabled.

  Each server already contains 6 cards (3 x Dual port NIC)

  I put 4 several NICs (2 x Dual port NIC)

  I had a bad experience with the addition of additional network cards before, lose the console service and overall. (new numbering)

  Somehow, I fixed that in fact separate old number and re-binder with new number assigned.

  Is there a best practices or procedures in this respect?

  Anyone can point me in right direction, URL, Blog or even simple command line to refresh my memory...?

  Thank you.

  It's easy:

  Remove the old nic:

  esxcfg-vswitch vSwitch0 - U vmnic2

  Add new:

  esxcfg-vswitch vSwitch0 vmnic1-L

  Duncan

  VMware communities user moderator | VCP | VCDX

  -

• Recovery of WAP54G - must .bin file in sync - or a .trx SEU command line method.

  Any chance that someone has an answer to this?

  I saw the same question and but never answered.

  I can't find all the "brick recovery methods require .bin files but not the .trx file.»

  What a great job if I get something like dd - wrt...

  However, in order to restore to a linksys firmware using a tftp Send WAP, I need the .bin file to sync I well... which seem to no longer exists.

  Quick, I found some old links that gave details on how to get it back (old linksys links) but the ftp server that hosted these files no longer exists.

  Any suggestions on where to find the .bin files or a recovery method using the new trx files?

  use the web interface, or replace the device is simply a lousy option.

  /Shrug everything ive tried does not work.  (including a version 1.0 and version 3.1) Yes 2 different routers.

  If it uses the bin files I can recover very well... including the warranty voind jtag method.

  Simply not an image provide Linksys (cisco), the TRX files.

  the Open source versions work fine...

  While WAP is not dead.   I can't use an official /shrug 'image '.

  What im reading there is a very very small differences in the .trx .bin files from...

  Think im stuck using dd - wrt for now.

  BAH - after a final test... rename the .trx file .bin for sync... Flash as usual.

  wait 3-5 minutes

  and then

  the IP address for the wireless est.245.1 not as I used too... the old version is still bounced a.1...

  So yes the .trx will work...

  /headsmack

  Thanks for the doublecheck... even when a person behaves like an A$ $

• Command line method of specifying the MAC address for a guest

  Can someone tell me if it is possible to manually change the mac address for a guest the cli? I was hoping that vicfg-vmknic can have an option statically assign an address but it is not. Depending on the Server Configuration guide, you can set the via the customer of VI, but the cli method is eluding me. Reason for wanting to do this is for a static dhcp address assignment

  Thank you

  Paul

  Another possibility - you can try VI Toolkit 1.5 which has a command called Set-NetworkAdapter, which allows you to set the MAC address.

• Add the network location in Windows Media Center for recorded TV

  Locations of tv settings, tv, recorder, more Windows Media Center does not outside of the local computer.  I used Media Center to record some TV shows and I want to spend my laptop on USB large network of an old desk for viewing later.   Because I can't point to this place I'm stuck.
  The files are on USB key and visible in windows media player and video location in Windows Media Center.  In other words, none of the news of the series is visible in Windows Media Center (but is in windows media player), so I can't continue to record series because Windows Media Center is not aware of the episodes already on USB network.

  Hello Johngi2,
  Thank you for your message.  To change the location of your recorded TV shows and always keep the info so that you won't get duplicates please browse to the following location in Media Center.
  Settings > TV > TV recordings > TV storage > storage location
  You just change the location of storage on your USB.  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Command line to stop ix2

  Is there a command line to turn off the ix2 gracefully from a connected PC to Windows 7? I want to add this line in a command/batch file.

  You can contact technical support to create an incident with them and I'll mention also that technology level 3 here as well.

• What is fledge command-line argument to control the graphics acceleration?

  Is there a command line argument to control the graphics acceleration for a JDE 5.0 Simulator?

  I would like to switch off in the command line so I can add it to the Simulator Run Eclipse IDE and the debug configuration.

  I checked their moult imaginal/Help and I have not found any that I could see that it works.

  Thank you.

  The settings are stored in a file located at

  \Documents and Settings\ [windows login name]\net\rim\fledge-2\fledge-saved.conf

  At the bottom of the appearance of file for the line:

  4
  

  Change the number 0 for no acceleration.

• Optical drive software command line switch

  Hello!

  Are there switches command line for the 'Optical Drive Power"- software TPSODDCtl.exe? This software is part of the package of toshiba power saver. I want to put in place to turn off my device optical drive at windows startup.

  Thank you
  Milos

  Hello Milos

  I use for Toshiba laptop more than 10 years now, and something like this is not known to me. I think that the answer to your question, that you can only get Toshiba software development service.
  I don't think that you will never get any info on this.

• Tools command line only for tiger?

  I have an iMac G3 carbon on OS X 10.4.11, with a small hard drive. Is there a command line only version of Xcode 2.5 tools?

  Hello redactedredacted,

  How tiny talk we? XCode 2.5 is less than 1 GB. You can download it here: https://developer.apple.com/downloads/

  Uncheck all the options except for the developer tools and scroll down. I don't know what options are available for the installation of.

• Addition of NIC to guest via command line

  I need help, trying to find the command line to add a new network adapter to several VMS of both comments and designating the name of port group.

  I tried to use the command below and it creates the new adapter but it is grayed out and I can't make any changes to the other that remove it through the user interface. Any help is appreciated!

  ~ # vim - cmd 10 99 vmxnet3 DR_Private vmsvc/devices.createnic

  I came back just to post that I got what I needed.

  (Already present changes network adapter)

  Get-Cluster cluster_name % | Get - VM | Get-NetworkAdapter | Together-NetworkAdapter - NetworkName DR_Private-confirm: $false

  (Adds the new network adapter in the CLUSTER)

  Get-Cluster cluster_name % | Get - VM | New-NetworkAdapter - NetworkName DR_Private - StartConnected-confirm: $false

  -Brian

• Not 'add printer network, wireless or bluetooth printer' choice in Add Printer

  ·        I am running Win 7 Pro 64-bit. When I go to devices and printers and select "Add a printer", the only option I get is to add a local printer. There is no other choice 'add a network, wireless or bluetooth printer. I have this choice on my other two computers running the same version of Windows 7. How to make this choice appears? I have the impression of sharing enabled.

  Thanks for any help - bob

  Hello

  ·        The printer is installed on the system?

  Method 1:

  I suggest you follow the steps mentioned in the article which is given below.

  The option "a network printer or a printer attached to another computer" is missing in the Add Printer Wizard

  http://support.Microsoft.com/kb/2211432

  Method 2:

  Open Help and support andput this keywords "Find wireless and network devices to add to your computer ' and follow the first article. Follow the steps to open the help and support.

  1. click on start and type help and Support in the research area, and then press ENTER.

  2 type the keyword "Find wireless and network devices to add to your computer ' and follow the first item that is listed.

  Method 3:

  Step 1:

  I suggest to uninstall the form the system printer and then reinstall it on the system manually. See the article mentioned below.

  Install a printer

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  Step 2:

  Enable sharing of printers and the discovery of the network. Check the items listed below.

  Share a printer

  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

  Enable or disable network discovery

  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discovery

  Now check if you are able to see the printer.

  Step 3:

  I suggest you to run a network troubleshooting utility.

  a. to run the troubleshooter network, right click on the network icon in the notification area of your taskbar and then clicktroubleshoot.

  For more information, see the article mentioned below.

  Network printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why 5.5 vcloud Director only has not the ability "add a network to an organization?

  I have deployed the ovules of Director 5.5 vcloud in my lab environment and watching videos. In the videos, the guy has deployed vcloud Director 1.5 eggs. I noticed that this homepage of vcloud Director 5.5 is not the option 'Add a network at an organization' as in vcloud Director 1.5.

  Did remove this feature in 5.5. Then I thought that it could be controlled from within the Organization after you create it, but again once I created the Organization, there is no option to add a network to this organization? I'm playing something here? How can we tolerate that they are private, the administrator of the Organization to create a network that is using a NAT or directly connected to the external network on the fly and remove it once it is not necessary. I though that it was a feature of the vcloud Director.

  I used the EGG apparatus, I have use the .bin file.

  Your help is appreciated. !!

  You EF network pool Org vDC wide (it's in properties)

  At the same time that you create a network Org inside the Org vDC going to just use the current network are entrusted to him.  Then, you make all your usual choices.  to do this, vDC display Org itself... go to list of org vDC in manage and monitor, and then double-click the VCC Org that you want to add a network.

  VAPP networks work exactly the same, create you them at the time the vApp is created.  This will use the network pool that is currently assigned to the Org vDC when the TIME Gets deployed.

  Overall, the function at the level of the consumer (org users) is the same, the process-level administration system has changed a bit.

• Windows 7 network number - need to add a network to obtain a download folder in the Terminal Server from microsoft services.

  In vista, I click Add a network place, and then selected some network places > entire network > Microsoft Terminal Services > \\tcClient

  What I do in the Windows 7 test

  Hi, Robert Sherman,.

  Welcome to Microsoft Windows 7 Forum.

  The features of Windows XP in my network places, be able to create a shortcut to a specific folder on a network resource, has been moved to the folder on the computer.

  Click computer in the Start Menu or click the computer in Windows Explorer.

  Right-click anywhere in the blank area in the right pane, and then choose "add a network location". On the 2nd screen, double-click Choose a location custom to open familiar dialog box to XP. Go to your network folder and add it.

  When finished, the new link will appear in the folder on the computer under network locations. It will no longer appear in the network folder, where it was in XP.

  For the program to install/add a network in Windows 7, please follow the mentioned below as follows:

  1. open the network and sharing Center by clicking on start, then Control Panel. In the search box, type network, and then click Network and sharing Center.

  2. click on work network, LAN or Public network and then click the desired network location.

  For more information, please visit the below mentioned link:

  http://Windows.Microsoft.com/en-us/Windows7/choosing-a-network-location

  Hope this help to solve your problem.

  Thank you and best regards,
  Calogero - Microsoft technical support.
  Visit our Microsoft answers feedback Forum
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and tell us what you think

• Add text from the command line to the output so that I can know how a command has been run when it generated the output

  This is a question and a suggestion...

  I would like to be able to precede or add if it works, the command line in the output file that creates the order.

  Example:

  I run dcdiag with switches, etc. and create an output file of results that gets saved or sent to a person or just put it in a folder. Of course, it could be that someone else ran the command and then sent the file. Anyway the problem is the same - what was the exact command line that has been executed to achieve these results?

  Question:

  Is there a known way to do from the command line that I can apply to any command?

  Suggestion:

  If this isn't the case, then I would suggest MS to include this function in all the BACK and PowerShell commands able to produce text output.

  If all goes well they monitor this forum and find it's a great idea and send me a check (pinky in my cheek) a meeellion of dollars. Then I and I alone will rule the world.

  Here you go:

  d:\>format i: / FS: NTFS > format.txt
  d:\>echo i format: / FS: NTFS > format.txt

• expdp/impdp method in the database upgrade from 11.2.0.4 to 12.1.0.2 an error in logic of "command line"?

  Hi DBA:

  We are evaluating different methods of upgrading 11 GR 2 DB to 12 c (12.1.0.2) this year, it is very important for us to use the right method.  It was reported that when DB version was 9i and has been updated to 11g, there were some order of tables 'line' was wrong when execute SELECT statements in application (Java application) - at the moment I didn't if it is ' select * from... "or any specific part with a"where"clause, and what type of data was wrong (maybe sequence CLOB data, etc.).

  I think I know, ' exp/imp', "expdp/impdp" logical backup of DB methods.  Therefore, Oracle automatically import data and fix it in each table.  If no error in impdp connects after it's over, should not be any mistake, right?

  If the use of the method of 'creates a new data + expdp/impdp basis for schemas user' 11g 12 c port data, questions:

  1. this method will lead to erroneous sequence data when ordering?  If so, how to re - generate the sequence number?

  2. this method can bring CLOB, BLOB data and without any errors?  If error, how to detect and repair?

  I use the same method in the 10.2.0.5 to 11g port data, no problem.

  I'll keep this thread posted after getting more information from application.

  Thank you very much!

  Dania

  INSERT... SELECT, CREATE TABLE in the SELECT and Export-Import will all "re-organize" the table by assigning new blocks.

  In place--update (using DBUA or command line) don't re-create the user tables (although it DOES not rebuild the data dictionary tables).  Therefore, does not change the physical location of lines for user tables.  However, there is no guarantee that a further reason for INSERT, DELETE, UPDATE instructions does not change the physical location of ranks.  Nor is it a guarantee that a SELECT statement will return always stored in the same order unless an ORDER BY is specified explicitly.

  If you export the data while it is still used, you don't avoid update sequences in the source database.  Usually results in a mismatching number sequence between the source database and the new database (imported). In fact, even the numbers may be different, unless you use CONSISTENT or FLASHBACK_SCN.  (These two options in exp / expdp do NOT prevent update sequences).   The right way to manage sequences is to rebuild or increase them in data imported with the values in the data source, once the import is complete.

  Hemant K Collette