ISE 1.4 - assignment VLAN dynamic based on originating nad

Similar Questions

• 802. 1 x assignment of vlan dynamic based on MAC?

  Hello

  I use Catalyst3750 and authentication widows AD.

  Our customers PC is driving Windows (is not able 802. 1 x) which is connected to the catalyst switch.

  Is it possible to dynamic assignment of that one Vlan based on MAC?

  When possible, we want to do it without help of VMPS.

  and is there any document relating to the foregoing.

  Thank you very much for you help.

  Tomoyuki

  Tomoyuki Hello,

  What Radius server that you use to authenticate your Clients?

  To Secure ACS, you can configure a feature called "MAC-Authentication-Bypass" that accomplishes your needs.

  This feature must be configured on the switch and the Radius Server (which makes the responsibilities of vlan based on the MAC address of the Client)

  An overview of this feature can be found here:

  http://www.Cisco.com/univercd/CC/TD/doc/solution/macauthb.PDF

  I hope this helps.

  Kind regards

  Chris

• Assignment of VLAN dynamic of the Web authentication

  In a firmware WLC 4402 v.5.2.157 is possible to assign users to one VLAN dynamic based on the RADIUS response received from ACS?

  Yes and no. You can do for a WLAN 802.1 x internal, that the customer does not get an IP address, until they have completed the authentication process. To do this, you use 64/65/81, 64 802, 65 VLAN and to 81 use the name of the interface, not the number VLAN. you will also need to make sure you have AAA Overrided activated under the WLAN.

  If, as is said for Web authentication, the answer is no. The client has an IP address before being validated by the AAA server.

  HTH,

  Steve

• Assignment of VLAN dynamic by using the WC7520 controller

  Hello

  I use a few AP WNDAP360 for awhile and consider adding a WC7520 controller.

  However, I would use an assignment VLAN dynamic using a RADIUS server.

  Whereas it is possible with the 360 in stand-alone mode, it is clear to me if this can be done by using the WC7520 controller.

  The (obsolete?) reference manual said not a Word to this topic...

  Is there someone to share experiences with the 7520 and this type of configuration?

  Hello

  Thanks for your help!

  After reading the articles you suggested, I was still unable to find a definitive answer, so I asked pre-sales support and quickly received the following response from Tech Support level 2:

  There was a feature request to ask to implement, but it looks like it will not be implemented for the WC7520. Also, there is a feature request for the WC7600 which looks more promising, but still not possible currently and is not guaranteed to be implemented.

  In short: no, it is not possible, will not be on the WC7520 and could become so on the WC7600.

  Too bad, and it makes the much less interesting WC7520 for me, but at least it clearly quickly.

• Assignment of VLAN dynamic RADIUS ACS 5.2 Server with NAC

  We are trying to reduce the number of ssid in our network wireless with assignment of vlan dynamic with the acs. Our problem is that we use Cisco NAC so with assignments of vlan dynamic user will be checked by the NAC. Agent of Cisco sometimes pop up and do nothing to do or give a message cannot locate server. We even got an OOB error. Someone used a VLAN dynamics with the acs and the NAC successfully? The NAC is Out of Band

  Hello

  I supported oob nac and wireless and your efforts to make the dynamic assignment of VLANs will not work because of the way in which him vlan quarantine and access are mapped to this ssid.

  This work in in-band mode, however your design. This WLAN key needs to exist because the Manager sends the snmp trap to move the client from quarantine access.

  Just as a note, I'm sure you are aware is that ISE is the evolution of the acs and the NAC. Basically this your solution to reduce the skates and posturing of the customers.

  Sent by Cisco Support technique iPad App

• NPS server - only Wired VLAN dynamic - Windows 7 - currently no available connection server

  Hi all

  I have deployed an NPS (Server 2008 R2) server with users added to security groups and configured VLAN DYNAMIC for wired connections (LAN) configured on the switch.

  And the concept works fine if the user has already logged on. But if the new user or user ID are set not to cache the user ID won't be able to connect.

  "Currently no available connection server ' for Windows 7 clients.

  Changes in the local AREA NETWORK CONNECTION for as below for the settings of 802.1 X.

  Specify the authentication mode: auth user or computer.

  enable single sign on for this network

  run immediately before the opening of the session.

  Networks through VIRTUAL happen seamlessly once connected, but if the user of the switch or new user whose profile is not connected to the user gets "no server connection.

  Objective: Users must be able to connect with their powers even without caching credentails.

  Need suggestions or responses on that.

  Thank you

  Shashi Kumar G

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• authetication affectedly 802.1 x Vlan dynamic by a radius server

  Hello

  At school, I want to start using authentication for 802. 1 x affectedly Vlan dynamic by Radius Windows Server 2012R2.

  When a student logs in, I want it to be placed in the Vlan 'Students', when an Administrative employee logs in, I want it to be placed in the vlan 'Administrative' and when the client is unknown, I want to place in the Vlan "invited".

  I have several SG200 switches and I have everything configured as described in the administrative guide but I can't make it work as you want.

  What does not work:
  -If the client is authorized, the switch enters the State "authorized". (until someone connects to the domain with this customer)
  -When a user opens a session which is part of the administrative staff, the switch becomes 'authorized' and when a student logs in, it turns into "unauthorized."

  So far so good.

  But what does not work:
  -It does not have the administrative employee in the Vlan 'Administrative', it allows the port of the switch comes, but he leaves in the vlan by default 1.
  -I can't find the VLAN comments.

  Any help would be appreciated.

  Hi Wouter,

  Yes you are right, 200 series doesn't support DVA. Only 300 or 500 have this level of the interface settings.

  Aleksandra

• How to assign URLs dynamically using button/link on the page of peoplesoft? Please provide detailed instructions.

  How to assign URLs dynamically using button/link on the page of peoplesoft? Please provide detailed instructions.

  1. define the URL, the Z_URL1 or the Z_URL2 definitions

  2. in the change of field button:

  If true Condition then

  ViewURL (URL. Z_URL1);

  On the other

  ViewURL (URL. Z_URL2);

  End - if

• ACS 5.2 assign VLAN based on the ad group

  I am trying to configure ACS 5.2 to assign the VLAN to a dynamic user based on the group to which the user belongs. I went to:

  Users and identity stores-> external identity-> Active Directory-> tab directory stores groups

  and selected the name of the pub group. If I understand correctly, I should now see this group by virtue:

  Elements of strategy-> authorization and permissions->-> authorization profiles for access to the network-> common tasks-> VLAN ID/name

  However, it is not. Am I missing something?

  N °

  ' VLAN id/name "is, in the name clearly States, a vlan id or name. Not a "group name".

  You don't assign it a group name in the vlan.

  The name of the group must go to the condition 'if' in your authorization profile. If "usergroup AD = x" and then assign this vlan.

  Then the id/name vlan's you type manually what vlan refers to the users AD Group.

  If you create too many rules because you have a lot of ad groups, you can do is create an AD AD attribute to store the number of vlan name and ACS will simply return that.

  Nicolas

• Assignment of the ACS 5.2 VLAN dynamic - problem of vlan voice

  Hello

  When I want to configure the VoIP VLAN through ACS, I go to elements of strategy > permissions and permissions > network profiles and then on the common task page select Voice VLAN > static according to the picture below

  

  Configure then configure the VLAN ID > static > VLAN_number

  But this only allows the VLAN voice and set it to VLAN_number, the VLAN DATABASE will remain unchanged and not configured.

  So my question is, is there a way to configure both the voice (and him) AND the VLAN DATABASE?

  I tried to manually add RADIUS attributes to a second VIRTUAL LAN, but it is not allowed.

  Any idea?

  Kind regards

  Thibault.

  Hi Thibault,

  Why you want to configure the voice and data on the same permission profile?

  If this configuration should be used for an MDA (multi-domain) config on the switch, then take account of the fact that the IP phone and the customer of data must go through separate authentication sessions.

  This being said, you should instead set up two profiles different autz and configure different rules in the authorization policy that apply "voice" for IP phones profile and the profile of 'data' for data clients.

  I hope that answers your question.

  Kind regards

  Federico

  --

  If this answers your question please mark the question as "answered" and write it down, so other users can easily find it.

• ISE 2.0 - assignment of the DACLS of Active Directory

  Hello

  Maybe someone can help me with this:

  I would attribute a DACL of an attribute I get from the user being allowed AD object.

  Thus, for example, I have set up 'ACL test' to ISE, the same name is assigned to a user of the AD.

  Now, I want to assign this ACL in an authorization profile with the value I get from the AD attribute.

  Under authorization profiles, I can't assign one AD the 'name of the DACL"attribute in common tasks.

  Does anyone have an idea how to do this with ISE 2.0?

  Thank you

  Joerg

  I doubt that you can do this, you must use the AD attribute as a condition in authz rules and reconciliation so only with an authorization profile, which contains your setting DACL. This means of course you will need an article by different DACL you wan't to use.

• some computers are not authenticated successfully with ISE and join comments vlan

  Hello

  We have deployed ISE in a company and set the workstations for authentication of the computer. When jobs are authentication, they are placed in the VLAN Data (5), if they fail, then they must be placed in the VLAN (50). WiredAutoConfig service as supplicant is set with gpo to all the workstations have the same settings.

  Certificate of the ISE is signed by our internal CA and workstations have also imported CA in their trusted CA list.

  The problem is that few jobs are placed in the VLAN. Previously on these workstations, we got a pop-up as below. When you click on 'connect' work stations have been placed properly in the data VLAN (5). We do not get this security alert more on these machines and they just join them VLAN that is don't want we want.

  However, most of the workstations is authenticated successfully.

  

  switchports configuration:

  switchport access vlan 5
  switchport mode access
  switchport voice vlan 6
  authentication event fail following action method
  action of death event authentication server allow vlan 5
  action of death event authentication server allow voice
  no response from the authentication event action allow vlan 50
  living action of the server reset the authentication event
  multi-domain of host-mode authentication
  authentication order dot1x mab
  authentication priority dot1x mab
  Auto control of the port of authentication
  periodic authentication
  authentication violation replace
  MAB
  MLS qos trust dscp
  dot1x EAP authenticator
  dot1x tx-time 10
  spanning tree portfast
  spanning tree enable bpduguard

  Journal of ISE authentication;

  auth1.PNG

  

  authen2.PNG

  

  Everyone is in a similar situation?

  I guess that the machines in the domain have the root CA certificate checked under the 'Protected EAP Properties' window?

• assign a dynamic action to a text element

  Hello
  using apex 4.0
  
  
  How to assign an action to a text element when you press the button.
  
  Thanks in advance
  
  concerning
  
  Published by: on April 13, 2011 02:17

  check: the dynamic of the trigger button Action
  OR
  {message: id = 9465043}
  {message: id = 9314562}

• Assign a value based on a condition of the varaible

  How can I assign a conditional numeric value to a variable based on the value of an xml tag. That is if she is 'company A' give it 12 if it is 'company B' 17. Also be able to use this value later in the model.
  
  
  Thanks in advance

  Use this:

  
  

  To retrieve and print its value later in the model simply put:
  

  It is documented here:

  http://download.Oracle.com/docs/CD/E12844_01/doc/BIP.1013/e12187/T421739T481157.htm#4535390

  Please spend some time to read the documentation for it.

  concerning

  Jorge

• Order by clause dynamic based on the Oracle

  How can I order by dynamic Clause based on the Oracle
  My query of sql function returns with SYS_REFCURSOR. and I will place the order of column as an input parameter

    create or replace
  FUNCTION TEST_SSK
  (
          p_srot  number
  )
  
  RETURN SYS_REFCURSOR
  
  AS
  C_testssk SYS_REFCURSOR;
  BEGIN
  
  OPEN C_TESTSSK FOR
  SELECT LOAN_CODE,LOAN_DATE,DUE_DATE,LOAN_AMT FROM LOAN_MASTER
  order by P_SROT;
  
  return C_testssk;
  end;

  Published by: user10736825 on December 22, 2010 11:34

  I think this would work without dynamic sql.

  You could do something like:

  ...
  OPEN C_TESTSSK FOR
  SELECT LOAN_CODE,LOAN_DATE,DUE_DATE,LOAN_AMT FROM LOAN_MASTER
  order by decode(P_SROT,1,loan_code,2,loan_date,3,due_date,4,loan_amt);
  ...
  

  P_SROT is the number of the order by column.