ISE GANYMEDE device Fitlers

Similar Questions

• ISE GANYMEDE authentication - connect before you decide if you should have access

  I'm away Cisco ACS to ISE Cisco version 2.1 to control GANYMEDE of my network devices.  I opened a proof with TAC but the answer, I seem to fly intuitive and hope for verification of this is now the way that Cisco or I just need to set up my policy defines differently.

  For a switch using ACS for the administration, a user will be SSH to the machine and if they are not in good AD security group, the user will receive a response from denial of access

  With ISE GANYMEDE to the administration, the user will be SSH to the machine and because they are a member of the AD domain they authenticate and connect the device actually get a command prompt.  Now this same user if they are not in the right group of safety AD that they will not be allowed to do anything on the switch.

  According to my TAC, ISE needs to identify the user, before he can decide if that user is allowed to access the device.  It is not fine with me because basically, anyone in my company can now connect on these devices.  Outside put ACLs on the switches that allow access only from certain computers, what are others doing to mitigate this risk?

  Thank you

  Hi Ken,
  In the event that you have configured your ISE with a new 2.1 installation, follow these steps:

  To the "device Admin defined strategy", leave the part "Authentication" of a rule as it is.
  In the "Authorization" section, add your security AD as conditions groups (select the box on the right under the conditions of-> create new condition-> to 'select attribute': 'AD login name'-> ExternalGroups-> 'equal'-> name of group to choose AD) and the right set of commands and the Shell profile for each security group.

  Now the importand part: the last rule is the default rule that will be used if the user is not a member of a security group that was the condition of an old rule.
  Here, you should make sure that the profile ' refuse of all Shell "is selected, it means that if this rule should be used, the user will be blocked from access.

  In case you went from 2.0 to 2.1, you may be suffering from this bug here:
  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCva04654/?referring_site=bugquickviewredir Then you simply do not have a profile ' refuse of all Shell "as an option.
  I'm building a work around for my system:
  I created a new profile of shell, which has a "disconnect" as command 0 privielege max level and auto.
  I loaded this profile of shell in the default rules.
  Maybe this isn't the best solution, but it does what it should do.

  Let me know if it worked and it please note useful responses!

  Greetings,
  Max

  Edit: spelling mistakes

• Consumption of ISE GANYMEDE 2.0 license

  Hi all

  I was experimenting with GANYMEDE in ISE 2.0.1 and recognized that there is no basic licenses consumend when I connect a network configured device.
  While when I connect with the RADIUS authentication, 1 base license is consumed per session.

  Is this behavior is intentional or a bug? As I intend to implement authentication GANYMEDE on a fairly large network, it would strongly reduce my costs when I do not have the device licenses.

  GANYMEDE is a license of power. It consumes no basic licenses that apply to the area of RADIUS

• ISE - network devices - Split larger range of IP addresses in smaller

  Hello.

  We have several companies, each of them have affected a subnet of class B, 172.21.xx 16, 172.27.xx 16, etc. for example.

  But each company has several locations, which has normally a class C subnet are assigned

  It is a structure that I want to build in ISE also.
  It is very convenient during authorization profiles and you will need to locate where the client is trying to access the WIFI. You know, to assign the VLAN, etc...

  But when I try to do, I get this error:
  Could not create the network device - given overlapping IP subnet with existing network device: 1.

  Why oh why?

  Is there a way to get around this? If this isn't the case, please implement this feature!

  It was no problem doing this GBA, then why would a problem here?

  Thank you

  Another way to determine where the wifi client is to use an identifier Sin you can specify a group AP or WLAN (by default it is the WLC name) and you can use rules in ISE that make use of the nas radius attribute - identify. The disadvantages with NAS-identify is that you must configure the identifier Sin from the AP on the WLC group, it cannot be done by PI model and you can make a report to ISE using an nas identifier.

• How to check the root cause of ISE hung device?

  Hi guru Cisco.

  One of the device of ISE of my client has just hung this morning.  He has rebooted and is back in business.

  However, the client wants to know the root cause.

  Is there a dump file that I can analyze?  Logging does not seem to have this information.

  Thank you.

  "show support" in the cli can enlighten us. (First set "term len 0" and connect the output - it will be over 10,000 lines).

  There are also a number of newspapers still more detailed - they are listed when you run 'tech show' that the TAC can analyze if necessary.

  If the problem is recurring they can ask you to activate certain debug level logs for more supporting information,

• Use of ISE 3355 device of the two GigE ports

  I'll put in place six ISE 3355 3 devices in a data center in another 3. They just installed a new infrastructure of server using 5596 Nexus and Nexus 2248TP farm top of rack switches.

  I am looking for documentation on how to make the collection of NETWORK adapters on the way 3355 or some connect Gig0 to FEX101 and Gig1 to FEX102. Or simply set up a channel using LaCP port between the two different groups of FEX?

  Sent by Cisco Support technique iPhone App

  Hello

  This is not supported, you can not team or balance the load or use redundant interfaces on devices of the ISE. You can only use a span port dedicated for ISE deployments, or use the links to crossover to a deployment ipep in HA mode.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• Department of foreign for GANYMEDE + via ISE - is RSA Secure ID the only option?

  I'm running Cisco Secure ACS to GANYMEDE and other things.  I have to move to another platform due to the requirements of PCI DSS 3.2.

  ISE is the head to replace ACS but I also have a requirement to implement a multifactor authentication (MFA) everywhere.

  2.1 ISE implementation guide says that RSA Secure ID is supported for the Ministry of Foreign Affairs with the GANYMEDE connections.  I did not have RSA Secure ID and probably never have it.

  The implementation guide and my provider Cisco also make the State more general that ISE will work with any solution of Ministry of Foreign Affairs which has a front end compliant RADIUS.  Well, it's because I already have one of these (SafeNet/SafeWord).  What they are not, is if it will work specifically to authenticate the RADIUS authentications.  The only docs I can find on this subject are all/only on ISE do this for the RADIUS clients such as ASA Cisco Anyconnect VPN client handling.

  Someone at - he obtained ISE GANYMEDE to work with the Ministry of Foreign Affairs with anything other than Secure ID? You have any links?

  Click on your name in the upper right to see your profile. Then choose the 'Message' tab and click 'New Message'.

• ISE and AAA configuration

  Hi guys,.

  I use that one server as primary and cisco ISE says there (ACS + NAC) features. I want to activate the AAA on the box rightnow ISE services.

  I used the ACS earlier and you want to configure the same functions in this regard.

  Authentication of devices in ISE when remote login for switch/router/firewall.

  Authorization of the form controls what ISE based on the user login

  Posting the details of command and connection and disconnection from the user.

  I have very basic knowledge of ISE but I used ACS througly.

  Please help in the question above.

  Thanks in advance

  Concerning

  You've probably used GANYMEDE + with your ACS; You cannot migrate this functionality to ISE does not support the ISE GANYMEDE +. You must take the device admin stuff on GBA.

• ISE 1.2: Employee with recording of flotation

  Hi experts,
  I am aware of this discussion https://supportforums.cisco.com/discussion/11962026/ise-12-device-regist...

  but looking for a detailed configuration to follow up on the work:
  The employee have access to the network with their departmental systems. No problem
  Employees must now be able to use their mobile devices to access. There is no definition of what devices are permitted.
  II think to let employees to register their devices with address private MAC in MyDevice portal would be the most sufficient solution.
  Any who have a detailed configuration or link how to do it?

  Thank you

  Frank

  Please see the link:

  http://www.Cisco.com/c/en/us/TD/docs/solutions/Enterprise/Borderless_Networks/Unified_Access/byoddg.html

• Cisco ise 1.2 installation of certificates for the issue of cluster ise

  Hello everyone I have a cluster ise 4 devices. 1 main admin/secondary monitor, admin of admin/primary secondary 1 and 2 knots of policy

  I need to install the Cert CA public on them. can I generate 1 CSR on one of the nodes, which includes a San with all the nodes DNS names?

  So get 1 single certificate by the CA and export and import the cert even in all other nodes?

  or do I have to generate 1 CSR for each node and 4 certificates of purchase? Wildcard certificates is not an option. Thank you

  Yes, you are right. The document was created before ISE 1.2. You can generate the CSR from the interface of ISE and add SAN.

  Kind regards

  Jatin kone

  * Make the rate of useful messages *.

• Authorization GANYMEDE - show arp

  I'm not a network administrator, but I get a number of devices that have the ability to manipulate traffic. There are times when these devices fail and will have to update the tables of arp cache and cam on our Cisco equipment. Due to this point of contact, I need the ability to verify the accuracy of these tables.

  Our team of Cisco uses GANYMEDE to manage access to our networking equipment. I had the ability to simply run the "show arp" and 'cam show' commands on a handful of devices, but have been informed that this is not possible because "show arp" is a privileged EXEC command.

  Unfortunately, I'm not in a position to be able to confirm or deny this, since I'm not familiar with Cisco or GANYMEDE device management. I was hoping someone in this forum could:

  (a) confirm that it is possible to allow individual orders without allowing all others

  (b) give some details on what to do in GANYMEDE to facilitate.

  All I need is to run these two commands - I don't need anything else. I suspect that our management team of GANYMEDE do simply not know how or do not want to implement this authorization. Your help to push would be appreciated.

  Thank you.

  "All I need is to run these two commands - I don't need anything else." I suspect that our management team of GANYMEDE do simply not know how or do not want to implement this authorization. Your help to push would be appreciated. »

  It's a very simple installation. Everything they need

  is the authorization of installation as follows:

  user = {test}

  Member = limited

  Login = the xxxxxxx

  name = "Scott Paul"

  }

  Group = {limited

  by default the service = deny

  cmd = {see the}

  allowed "arp. * »

  allowed "cam. * »

  deny. *

  }

  }

  With that, your account Ganymede may only

  run "show arp * ' and ' cam show."

  commands and nothing else.

  Easy right?

• procedure to join unit ISE become node posture inline

  Hi all

  I ask, because I had 2 units of ISE-3315 device, we need to be the primary node of monitoring service admin-policy, another unit then become node posture Inline.

  For the preparation on the node line posture, what should you do about it?

  My question is:

  01 for the unit ready to become inline posture, so I simply start, install the OS of sractch (using version 1.1.1), then start the configuration to initialize etc, as the Normal Installer?

  02. until I regieter, which is the deplotment nodes should I choose to posture inline node unit?

  condition that the admin-service-management policy will become the primary node and node of posture inline registration will be the next action.

  Thank you

  Noel

  Noel,.

  The scope of my comment was based on the deployment of the ISE, the VPN nodes and Ipep use RADIUS. The connection to the IPEP and vice versa ISE node admin will have adequate certs in place because they use ssl to authenticate and encrypt their data.

  Thank you

  Tarik Admani
  * Please note the useful messages *.

• 5.2 Cisco ACS system alarm [Collector]

  Hello

  I have a problem with my ACS 5.2 General reports, if anyone can help would be great.

  We have two ACS 5.2 primary and secondary. Both work fine, but have an alarm to the General reporting system.

  list '(too long) value '.

  I have attached the screenshot of this error.

  At this point, we use GANYMEDE device of authentication only, no RADIUS. These servers are sync both conf are the same.

  Don't know what exacly causing this system error, can anyone help on this.

  Thank you

  David

  This has been observed when an accounting packet is received on the device of the ACS and lacks the attirbute class. However it is a cosmetic issue and there is no bug on this. If you want to have someone look at this and addressed if please collect newspapers of debugging at the level of DURATION and mgmt-acsview newspapers and open a service request on when the problem occurred.

  You can do SSH to GBA, then issue the command acs-config, connection with web references, and then publish a newspaper of the show debugging, if all levels are set to warn, then issue-journal of debug runtime level perform a debugging, debugging acsview mgmt-debug log level.

  Repeat for both servers, once the error is present, please download a package of support.

  Please open a service with this information request and we will be more than happy to help.

  Thank you

  Tarik Admani

• wireless users

  Hi all

  I have this error message on cisco ISE 3315 when authenticate my wireless users.

  "Dynamic authorization failed: 11213 no response received from the network access device.

  I have a cisco ISE 3315

  and my access point is a CISCO WAP4410N without controller (WLC)

  My access point is to enroll in the ISE NETWORK DEVICES.

  Hello

  Standalone ap nit support cost. If you are profiling devices, you can disable it in the deployment settings. You can also disable coa in the admin under the section profiling settings.

• Passwords enable ISE device Administration (ACS) integrating with Active Directory

  I'm working on a standalone application ISE and running into a problem where the password to enable for a device is not shoot properly.  I have the original connection related AD and I policy conditions/results/sets all as they should be working.  My test run is a 2960 S.  I tried to set up ' group aaa authentication enable default Activate ', but the only way I could do a login enabled with which was if the user has configured locally in ISE identity management > identity > users.  Is there something that I missed that tie will enable passwords for a group active directory as I work for the initial logon?

  I see just a mistake with your failure to enable aaa authentication enable. You must specify the Group of Ganymede.

  Right now, I don't have access to my lab with ISE.

  Here's my config for switches used with ACS.

  AAA authentication login GANYMEDE-SRV Group Ganymede + local
  local authentication AAA Console connection
  Group AAA dot1x default authentication RADIUS
  AAA authorization exec GANYMEDE-SRV Group Ganymede + local
  AAA authorization commands 15 GANYMEDE-SRV Group Ganymede + local
  Group AAA authorization network default RADIUS
  AAA accounting exec GANYMEDE-SRV arrhythmic group Ganymede +.
  orders accounting AAA 15 GANYMEDE-SRV arrhythmic group Ganymede +.

  If you give me all out maybe we can understand why your GANYMEDE ISE works do not with the AD. I see no reason except a misconfiguration or another issue.

  Just to go to the mode, you need more aaa authentication command activate by default enable. This activation mode is pushed to the user if he gets the privilege 15. Your problem should be on the profile or politics. With the approval journal, we can see whether or not ISE pushes politics and why?