Issue using the usb storage device

Similar Questions

• Windows 7 is no longer reads the USB storage devices

  I have a problem similar to some other posts, but different enough so that I write it here.

  When I insert a USB storage device (like a Microcenter * Go Flash) Windows 7 Ultimate just shows a yellow exclamation mark next to the device in Device Manager. OtherDevices, USB Flash drive. Software update driver fails, no update.  Uninstalling and reinstalling has no effect.

  Under properties:

  Type of device: USB FLash Drive

  Maufacturer: unknown

  Location: Port_ #0003.Hub_ #0008

  Pilot wrote:

  Privder: unknown

  DAT: Not available

  Version: Not available

  digital GIS: dig signed ot

  Under Details:

  Hardware ID: USB\VID_1307 & PID_0163 & REV_0100

  USB\VID_1307 & PID_0163

  There is no ping, no popup. Nothing. All this used to work very well, and now, when I need to copy files to work urgrnetly, he's dead.

  Just rub a little salt, I CAN access the device through Linux in VMWare Workstation. But when vmware is not current execution, or when I disconnect and try to attach to host, nothing happens.

  I tried each storage device USB I can find and no luck on any of them.

  Thank you

  TMB

  After digging through the forums, I tried to copy the usbstor.inf and .pnf to the Windows\inf directory and reinstalled the driver through the Device Manager, and it loaded right up.

  I don't know, but I suspect that the impact of this change, there are other devices that can complain. For now, the process of transfer between W7 and VMWARE/linux seems flawless.

  TMB - back

• HP Compaq 8100 Elite: Boot interrupted by the USB storage device

  If I have any sort of plugged when starting USB storage device, I just get a blank screen with a blinking cursor.

  I disabled each device start-up apart from the internal SATA hard drive and it still happens.

  Finally I found a BIOS update.

  On the HP consumer Support Site? NO.

  On an alley, ad - ridden, dirty pilots-for-all site.

  Anyway. It worked

• Using the USB audio device as default instead of analog audio ports

  Audio microphone USB installs and is listed in the devices under sound, video and portable with Dell computer game controller devices running Windows Vista, but the problems the system to use the USB mic as the default.  The sound devices list has also IDT HD audio codecs indicated, and the system will analog as the default input channels for the microphone, with no way to install the USB device.  Is it possible to put the USB audio as default microphone device?

  Hello RSA 456,.

  Many sound problems are caused by hardware that is not configured correctly. We will check your sound card, connect the cables in the correct locations, ensuring that the material has the power and the verification of the volume.
  Please follow the method described below to solve the problems.
  Method 1:

  1. plug your USB microphone.
  2. the LED will light to indicate that it is powered USB.
  3. Windows will automatically detect the USB Audio device and install the universal drivers.
  4. to set up your microphone as default device USB Open Control Panel.
  5. Select display as a classic view of your control panel, then select Select Sound.
  6. click on the recording tab. Here your USB Microphone will be listed.
  7. click on the USB microphone. If there is no checkmark beside the USB Microphone, click on set as default.
  8. the default device is used in most programs such as tape recorder simple registration.

  Method 2:
  Please click the link below to check how to check if the hardware works just fine.
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows?T1=tab02

  Kind regards
  Sooraj.S

• E4200 with Win 7 - could not connect to the sharing of files on the USB storage device

  Hi, I tried several disks now, but am mainly interested in getting my Iomega 1 TB drive to work, but none of the 3 I tried to do. None of the USB drives I had when buying this router on the list of "approved" ridiculously short which is of course not noticed when buying the router, but the discs are recognized, I can FTP to one of them (Filezilla), format, create to-DOS, etc. via the web interface... the only thing that does not seem to work is to map the created actions. The error obtained net use is 'System error 1231' giving in 'Map network drive', 'Windows cannot access\\192.168.1.1' with 0x800704cf error code. I get what I pass credentials or not. Please advise, external storage has been the main reason that I bought this router and I need to know if I should return it. Thank you

  I know that sounds totally absurd given that FTP and what - not worked, but I swapped the USB cable I was using between readers and the router, and presto, it worked. I been in this business a lot of time and work with Cisco equipment all the time, so I know how ridiculous, this sounds like a solution, and perhaps in the context of permutation that cable thing happened I can't remember since I was a package 6 deep at the time... but it works now... now, if I can get just the AVI 1080 p files to stream to Xbox 360 without the video do rough I will be gold... but that's another thread. Thank you all.

• remove the usb storage device

  I use the safely remove hardware in the taskbar before you remove a USB flash memory.  When I plug in my pc doesn't recognize not unless I restart the computer, is there a way to bypass restarting my computer to recognize memory flash usb again, Ed

  You are welcome.

  Please click "Propose as answer" on this page so that this thread can be closed.

  K M JAI Support general (INDIA)

• can I use the mass storage device to speed up windows xp, like ready boost on windows7

  non-essential programs, defragmented, disk cleanup, always short slow.

  non-essential programs, defragmented, disk cleanup, always short slow.

  Hey snowblindxxx

  Here is a link to the xp for you forums

  http://answers.Microsoft.com/en-us/Windows/default.aspx#tab=4

  Answers by topic

  • Office & Customization
  • Files, folders, & search
  • Game
  • Hardware drivers &
  • Install, upgrade, and activate
  • Internet Explorer
  • Music & Sound
  • Networking, mail, electronic, & updated online
  • Maintenance & performance
  • Photos & Video
  • Programs
  • Security, privacy, and user accounts
  • System repair & recovery
  • TV and movies on Windows
  • Windows Update

  Walter, the time zone traveller

• Deletion of data (step by step) USB storage device

  I need to know how correctly, step by step, remove a usb port connected data storage device. I am currently using, Windows visit Home Premium. Thank you...

  By the clock in the bottom right notification area, you will find an icon. Hovering over it said something like 'remove hardware safely '.

  Double click on this button.

  Find the usb storage device in the hardware list.
  Select this device.
  Click on stop / remove safely

  Wait until you receive a notification that can be removed.
  Remove the USB port.
  If so, you can now safely unplug unit from wall outlet as well.

  I hope this helps.

• Driver for usb storage device

  Hi, I have a packard bell No. PEW96 pc and I use a windows 7 Home premium. The problem is that the pc is not a driver for the usb storage device. How I can install it and how I can find it? and the name is? I hope you reply and help me to resolv this.thank you

  Moved from feedback

  Original title: usb storage driver

  Look in their Download Center.

  http://www.PackardBell.co.UK/PB/en/GB/content/download

  Good luck.

• When a pop-up message indicates that a storage device has just been attached and I don't put a USB storage device into the computer at all, what that means?

  From time to time, (isn't that every now and then, not every day or every week) a message appears on the computer screen to notify that "a storage device has been attached... and something or other on a port '-as it would if a new hardware device had just been installed or removed... only, I have not attached at a storage device.

  In fact, apart from the scanner, printer and keyboard connected, which are already inserted until the computer is turned on, no USB storage device or any other thing seized or inserted into the computer when this message is displayed on the lower right screen where the icons on the desktop are,

  Why would this happen unless I had personally inserted/joint a USB stick storage device myself in my computer?

  I'm afraid that maybe someone to access details and store information from a remote location via a storage device? Is this possible?

  And if it's an error of some sort, how to fix this problem?

  Please notify. Thank you.

  This probably means you have a bad USB connection somewhere.  I got this a lot when I used markets good USB hubs.  It also happened a lot on a couple of the USB plugs on my old laptop 4 year, where I had plugged in and out things in them so that the connectors are not as strong as they were when new.  My main office more connected devices above that outputs 4 USB, that I had on the back, so I finally bought a card extension to add 4 more exits USB.  If this is your case, perhaps you could do the same.  Expansion cards are not very expensive, usually in the range of $ 15 to $ 25, and they are fairly simple to install.

  I hope this helps.  Good luck.

• You receive the error software device driver has not been installed successfully using the USB LAN cable

  Original title: Please help!

  I bought a USB - LAN cable, but when I try to use it, this thing came out, "device driver software was not properly installed", then what should I do to use this cable properly? l

  Hello

  Thanks for posting in the Microsoft community!
  You have reached the right forum for your question. If I understand correctly, you receive error software device driver has not been installed successfully using the USB LAN cable. I suggest you follow the troubleshooting steps to check if this may help.

  1. don't you make changes on the computer before the show?
  2 are you able to get any USB devices to work in USB ports?

  Check the status of the device and the driver Version:

  a. open byclicking the button start Device Manager, click on Control Panel, clicking system and Maintenance, and thenclicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  b. double-click the category containing your device driver and thendouble - click the device name.

  c. check the status of the device tab click on driver tab arencontre, checkDriver provide, Date of the driver, the driver Version, digital signer. Please provide this information.

  d. click OK, exit Device Manager.

  Method 1:
  You can update the drivers on the manufacturer's Web site and check.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Use Windows Update to find a device driver
  Note to use Windows Update, you must be connected to the computer as an administrator:
  Follow these steps to use Windows Update to find a device driver: a.Click Start, click all programs and then click Windows Update.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  b check the updates.
  AA,a,AB,b,c.to determine if there are updated drivers, click on view available updates.
  If updates are available, click the driver you want to install, and then click on install.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  If you need further assistance, please answer and we will be happy to help you.

• Impossible to disconnect itself from USB storage devices

  Original title: USB storage devices

  Once more I couldn't properly disconnect a USB storage device because Windows tells me that a program is still using the device. There is no reason for any program to access it then why on earth isn't Windows the task/program name so that I can address the issue instead of having to restart my computer? Of the many irritants "characteristic" of Windows, it is one of the most galling.

  Hello

  ·        What is present in the USB key?

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest you follow the steps mentioned in the article below and check if the problem is resolved.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  If there is nothing important in the USB device, I suggest you to format the device and see if the problem still occurs.

  Note: If there is no important data in the USB then, back up data, and then format the USB.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Almost any time I use the usb climb on my computer (with flash or ipod players) it freezes and crashes windows. I am up to date with drivers with Microsoft and HP, what can I do to stop this?

  I have no problem with the usb drives but in recent times, this happens all the time.  I can go into Device Manager and uninstall my usb drivers and allows that, sometimes, but it's a temporary solution.  I am up to date with drivers with Microsoft and HP, what can I do to stop this?

  Hello

  You can try to use your boot USB storage device and check if that helps. A clean boot helps eliminate software conflicts.

  The following link has steps showing how to perform the clean boot. http://support.Microsoft.com/kb/929135  
  (1) perform the clean boot
  i. Click Start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  II. in the general tab, click Selective startup.
  III. under Selective startup, clear the check box load startup items.
  IV. click the Services tab, select the hide all Microsoft Services check box and then click Disable all.
  v. click OK.
  VI. When you are prompted, click on restart.
  VII. after the computer starts, check if the problem is resolved.

  (2) enable half the services
  (3) determine whether the problem returns
  (4) enable half of the startup items
  (5) determine if the problem returns
  (6) repeat the steps above until you find out which program or service is causing the issue
   
  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.
   
  Note: Please make sure that the computer is configured to start as usual by following step 7 of article http://support.microsoft.com/kb/929135 .

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  (i) click Start, type msconfig.exe in the start search box and press ENTER. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  (II) on the general tab, click the Normal startup option, and then click OK.

• IX2 - usb storage device?

  I have a storcenter ix2 and wonder if it can be used as USB storage connected in local device or is it strictly a SIN?

  Thank you

  DTK,

  The ix2 is strictly a NAS.

  However, these things can be circumvented these days.

  If you are inclined to do, you can buy a USB adapter to Ethernet and / access handle the actions in this way.
  https://www.Google.com/webhp?SourceID=chrome-instant&ion=1&ESPV=2&IE=UTF-8#q=USB+to+Ethernet+adapter

• Repeater wireless WRT1900AC + USB storage device

  For my setup, I had to use this router in wireless Repeater mode and continue to share USB storage. To my surprise, I found that the USB storage function wasn't available anylonger as well as most of the other functions. The problem is that I can not, and surely there is no rational explanation for why the function of USB storage isn't here as

  1 opportunity Samba server has no requirements for a device to be a MAIN router hosting

  2. the router assigned IP address (DHCP server or statically) seeps

  3. the router was also named network assigned

  So my question here is really not WHY, but rather WHEN it will be addressed by Linksys Engineering? Must still hope us to achieve this functionality is enabled in future versions of the firmware.

  I did the below application functionality with Linksys Engineering about this thread:

  ---------------------------------------------------------

  Feature Request for the series of EA USB storage routers

  Users request the storage USB not be disabled when the router is in one of its Modes of Repeater\Bridge.

  ---------------------------------------------------------