jump motion controller is disconnected

Similar Questions

• Cannot find the motion controller

  I use a 12 unidex by aerotech motion controller.  My labview program worked well, my motion controller when all of a sudden he couldn't find it.  I went measures and tab automation looking for him, but he could not find the controller.  The program has been able to find all other connected devices, but not the command of movement.  I disconnected all other devices except the unidex and labview still could not find it.  Then I took the controller and it covered on an identical motion controller (no reason to).  Not only labview couldn't find the first motion controller, he could yet find that I had grafted on.  Thoughts?

  Good new everyone: the GPIB address was surreptitously to 0 which remote impossible given that this value is reserved for the GPIB controller.  I appreciate the advice of each.

• Motion controller does not work on the Qosmio G50

  Hello

  as well as problems with my touchpad that I can't seem to get the job and my fn + f9 that does not work, I discovered today that my gesture controller no longer works?

  I went on the site of toshiba europe and downloaded the latest driver for it but once again, I received the message "an error has occurred in the toshiba quad core processor HD = 0x800A0100 code?

  Any help would be wonderful that its driving me around the bend!

  > as well as problems with my touchpad that I can't seem to get the job and my fn + f9 that does not work, I found out today that my gesture controller no longer works?
  So much trouble, you got there. You may create a Groove and reinstall the original recovery image. After having done this you own preinstalled OS and with the factory settings, everything should work again.

  What do you think about this?

• HP envy 17 jump motion is: forgotten password

  I recently moved and I left everything for my HP envy 17 back home. Now I can't past the administrator password or power on password when I first started cause I had everything written down. Can someone please help me to reset it. After the 3rd time trying to get I get a system box is disabled with the following numbers. [69730305] If you please help me get through this. Thank you

  Hello

  Enter: 76698921

  Kind regards

  DP - K

• Encoder with motion controller

  The PCI-7332 is usable with an encoder with output asymmetrical? If so, how?

  All the PCI-7332 encoder inputs are single ended.  Take a look at Chapter 5 of the following manual for an explanation of the encoder inputs and how to wire them.  It is said 7330, but it's also the manual for the 7332.

  National Instruments 7330 manual

  http://www.NI.com/PDF/manuals/370837a.PDF

• Sampling motion controller analog voltage (from a load cell)

  
  

  Dear nstroud,

  Or the other of these commissions should work for you. You can configure one of the axes for engines step by step closed loop analog feedback and then put in place the other 2 axes as slaves to the first with a debt ratio of 1 to 1. This would cause all 3 of your axes to behave in the exact same way. This transmission is made on the card, and you should not see any negative impact on the axes update rates. The specified sampling rate should not be a problem either. The update of control loop period is definable in the adjustment of the loop tab, and for stepper motor axes, it determines how ofter the step generator is updated. The default for this value is 250 milliseconds. The 7340 user manual also lists the scanning speed of demultiplexer of analog input @ channel 25 microseconds / activated.

  So you would be actually sampling and update the engine generator step much faster than 100 Hz with analog feedback on axis controllers.

  See this knowledge base for more information about the configuration:

  Analog feedback with a stepper motor:
  http://digital.NI.com/public.nsf/allkb/AB3CCA7FBFAD749A8625713B001D8581?OpenDocument

  Best regards

  ~ Nate

• Processor Quad-Core HD Qosmio G50 and gesture of the controller error

  Hello
  I have a Qosmio G50 - 10v. For gesture controller request from the Toshiba.I site, I installed a gesture controller driver tried the English and German version, but for the Quad Core HD processor shows error. The message is
  like the following"Im Toshiba quad core HD processor Fehler aufgetreten ist. (CODE = 0X800A0100)
  Later, I formatted the pc and reinstalled the processor image driver and motion controller. When I open a Toshiba DVD player and watch DVDs, Quad core does not work and quad core shows 0%. So I watch movies with low definition.
  Please help me...
  How can I install the Quad core HD processor and controller of gesture?

  The "Toshiba Quad Core HD processor" gadget works when I've been upgraded / decommissioning or other video processing in the "Toshiba graphic Video Library»

  To check this, click on the red arrow on the left side of the gadget, click on "library graphic video Toshiba", right click on a video and select "vidéo Processing", then try and upconvert or downgrade a video according to what kind of video it is.

  Simple treatment should see the upper left quadrant the gadget turn orange or red while showing a percentage. Complex treatment, perhaps using one of the other programs in the menu drop down the gadget can do all four quadrants of the gadget actively processing colors/percentage of changes. I saw all active quadrant during certain functions of video processing. I've not seen it activates when not video processing.

  The program that you are running appears in the white box in the gadget under "request of race."

• Re: Qosmio G50: How do I uninstall gesture controller

  Hello

  I had to do a re-installation of my windows 7 ultimate on my qosmio G50 32 bit repair...
  after it was over I had my gesture controller error messages.

  So I guess I need to uninstall it.
  I go into Control Panel and find it in the list, click on uninstall and after he did his time I get a box indicating: 1310.error writing to the file error: C:\config. Msi\4cb46d. FBR. Make sure you have access to this directory.

  I click on start again and I get the same message every time?
  and then after that, I get another box saying: error 1603 Fatal error during the instillation. For more information, see Help for windows install (Msi.chm) or MSDN?

  What should I do?
  Any help would be much appreciated... cheers. Neil

  Hello

  You can try to uninstall the software by using a tool like CCLeaner third 3rd.
  This allows to remove the software and clean the registry.

  You can also try installing the motion controller without uninstalling the software first.
  But I don't very well if it would work for sure m.

  However, visit the Toshiba Eu driver page, download the gesture and try to run the installation program

• How can I remove iee1284 controller?

  Connected to an old HP Laserjet 1100a via a parallel to usb.

  In a first time, that he did not work, then through add printer I connected the device via the USB 2 port and it worked fine.  Drivers installed and its fine print.

  However evety time I connect the printer, I get a device controller IEE1284 who wants me to troubleshoot the appliance and when she does cannot find the printer driver.  My other still works fine.  How do I remove the IEE1284 corrector?

  Thank you

  Colin

  Hello

  Uninstall the IEEE 1284 controller and disconnect the parallel to the USB controller and see if the problem is resolved or not.

  A: type device manager in the search box of start and press ENTER.

  B: locate the IEEE 1284 controller and then right-click on it and select uninstall.

  C: restart the computer and then reconnect it back in the printer.

  Hope that helps.

• Error messages when I connect to a controller

  Hello. I hope this isn't the wrong section.

  I just installed a controller Xbox on my PC, using x 64 drivers here

  Unfortunately, I still have error messages when I connected controller. If the controller is disconnected when I turn on the PC, then I got the error when I connect it.
  A mistake is on C++ and the other on "XboxStat.exe has stopped working". Seems is not entirely compatible with the 360 controller drivers.

  The error messages photos here:

  http://I57.Tinypic.com/2i6mlgy.jpg
  http://I57.Tinypic.com/332uo7p.jpg

  I have Win7 x 64 with all updates.

  Hi Marco,.

   
  As you have tried the steps that are proposed before and still the problem persists, I suggested you to indicate the query in the Xbox forum, as the question is specific with the Xbox controller. So, please post your query it using the link below, so that the Xbox support team can help you solve the problem.
  http://forums.Xbox.com/xbox_forums/default.aspx
   
  Hope this information is viable to fix the problem.

• JavaLoader 5.0.0 able to load the cod but debugmode connects then disconnects instantly

  I am able to complete the following:

  U C:\Eclipse\plugins\net.rim.ejde.componentpack5.0.0_5.0.0.25\components\bin>JavaLoader-p0x23515341-D1-charge - w5150 C:
  \Users\toddj\Documents\BBProj\Coffeehouse-BlackBerry\deliverables\Standard\5.0.0\Coffeehouse.cod
  Charger Pocket RIM Wireless Java
  Copyright 2001 - 2009 Research In Motion Limited
  Connected
  Coffee done loading
  262188 bytes sent to ~ 1048752 bps
  Disconnected

  C:\Eclipse\plugins\net.rim.ejde.componentpack5.0.0_5.0.0.25\components\bin>JavaLoader-p0x23515341-D1-w5150 u debugmode
  Charger Pocket RIM Wireless Java
  Copyright 2001 - 2009 Research In Motion Limited
  Connected
  Disconnected

  My question, why connect debugmode then immediately disconnects?

  Finally, I would like for debugging on the device of Eclipse, but when I select "Debug As BlackBerry Device", nothing happens - the debug perspective does not open and I do not see any notification process.

  Geez, why is it so * beep * ing difficult at the same time.

  Finally!

  Hallelujah!

  I can't believe that the fix was to use BlackBerry Java plug-in for Eclipse Version: 1.3.0. I'll have to take the good and the bad on this one. 1.3.0 is far from ideal, but I have to be able to debug on the device.

• Breakpoint of position synchronization

  Hello

  I run an application where I am synchronization of data acquisition with the engine query step by step using the breakpoint of my motion controller feature.  Ideally, I would like to synchronize the start of data acquisition with a known position of the engine within 1ms.

  The way I currently have the updated code in place, my motor and encoder initially begin to zero steps/count indictment, then move in a negative way.  I want to start pretty close to the start of the query the DAQ (the exact time is not serious, but I need to measure accurately the corresponding position); to do this, I put my breakpoint to trigger when the encoder position is-1.  However, looking at the position of the encoder measured (using reading encoder Position.flx), it is clear that the encoder "jumps" from 0 to-10 steps as the engine passes through the first stage.  According to the angular speed of the motor, this takes ~ 5ms.

  So I guess my question is, even if the breakpoint is set at-1 he will actually trigger when the encoder reads - 10 since he does not exactly 1?  Or do I somehow interpolate between the measures of 0 and -10 to estimate the moment that the rail - 1 Encoder?

  I use a PXI-7354 controller and an acquisition of data PXI-6229 mounted into a chassis SMU-1062 q.  Data acquisition is connected to a module SCXI-1520 strain gauge with a SCXI-1314 mounting block (I don't think that what counts in what concerns the latency relaxation time).  My engines are set to 400 steps/rev and the corresponding encoders are 4000counts/rev; they are connected to the controller of movement through a UMI-7774.

  Thank you in advance for your help!

  Matt

  Greetings, Matt;

  I apologize, I did some research but assumed that I must have forgotten to post it.

  After discussion with someone in R & D, it seems that the breakpoint is triggered when the encoder transmits the brand-1. Now, if there is a reading when the encoder is in the - 10, he can score in the software that the engine stopped to of-10. However, because the case is done at the hardware level, the pulse will be sent exactly at what time the encoder through this point-1.

  Again, I apologize for the delay and wish you a nice day.

  Best regards;

  Simon P.

• measurement and automation explore (MAX) version 4.1.0.3001

  Hello

  I used MAX recently and he suggested a firmware update, which at the time I said no.  Now whenever I start

  MAX and select, my device under devices and Interfaces I simply get a message waiting hourglass, no error message

  are visible.  What would be the best way to solve this problem?  It gives me is more a chance to update the firmware for my motion controller

  device.

  Treyphond

  Treyphond,

  I have not seen behavior like this before. Please uninstall NOR Motion, disconnect your motion control board, reinstall the latest version of NOR-Motion and reinstall your Board again. Please let me know if this solves the problem.

  Thank you

  Jochen Klier

  National Instruments

• UMI-7774 required for readers of nor?

  I'm a movement control system design using 3 stepper motors (or Nema 23) and therefore 3 or P70360 readers. Is a umi-7774 required to connect to the controller 4 card pci motion-axis?  (I'm confused as its description on the site nor said that it is necessary for the 3rd party readers BUT in discussions I've read a lot of people have used umi 7774 or readers)

  Hello aks.

  Yes, you will need to purchase and use our 7774 universal movement (UMI) Interface to connect the three engines of readers / motion controller card.

  He could have confused because it does not explicitly say that it is necessary for the 3rd party readers, but not necessarily required for our readers. That said, the vast majority of customers use the UMI Board, because it eliminates the need for custom cables and makes it much easier to connect to several axes.

  Here are some links that can provide more details and could be useful.

  [1] NI Stepper Motion System selection guide

  [2] of wiring for a movement with a Danaher drive system explained

• Linearmotor does not

  Hello

  I have a linearmotor (4 pieces) and must use it with the PCI7350. When I turn off the output of the inhibition, I can activate the engine with a simple program of LV and can swith the controller in the current mode (for use with ADC). If I turn on/off the output inhibit I can't use the melody of servo able and Automation Explorer.

  What's wrong?

  Best regards
  Andy

  linearmotor (LinMot PS01-37 x-240 c)
  Regulator LinMot B1100-V (current Mode) connected to the UMI7764 with a voltage converter
  2 x UMI7764
  PCI7350
  LV2011
  M & a 5.0.0f1 Explorer
  NEITHER Motion 8.3

  Hey,.

  GRR. Rookie mistake. I had to save and to initialize the motion controller after switching on of the polarity of the inhibition.

  Best regards.

  Andy