LabVIEW DAQ Assistant accidents

Similar Questions

• missing 2013 LabVIEW daq Assistant

  I do not see the DAQ assistant in Labview 2013!

  LabVIEW 2013 + real-time + fpga

  Max 5.5.1

  Visa 5.4.0

  August 2013 device driver

  Why?

  Thank you

  
  

• problem with the on LABVIEW DAQ assistant.

  I have a LABVIEW student edition. I needed to use NI USB-6008 to acquire the signal, but I do not see "DAQ Assistant" on the Express > entry in the block diagram pane anytime, I opened a new VI. Any help will be appreciated.

  Thank you.

  
  

• Impossible to find in LabView DAQ assistant

  Hello! I installed the driver NOR-DAQmax 9.3.5 after installing LabView 8.5 Student edition and I'm not able to find the DAQ Assistant, in the function palette. Could you please let me know what else I could do?

  Thank you!

  Hi cmorale4,

  Find this article in the DAQmx driver compatibility and LabVIEW, if you have the latest driver that you can install and use with LabVIEW 8.5 should be OR-DAQmx 9.3 you can find here.

  The best method is to remove all the drivers you have installed so far, you can do a registry clean with CCleaner and then proceed to the installation of version 9.3

  Kind regards

• Missing 2012 LabVIEW DAQ Assistant

  Hello

  I just installed LabVIEW 2012 and DAQmx driver for my USB-6008 and there is no DAQassistant in my menu of LabVIEW.

  I searched using the search feature on the menu, but he's not here.

  I installed LabVIEW before DAQmx by following the instructions on the Web site of NOR.

  Thanks in advance!

  You did not provide certain essential information - the version of DAQmx you have installed. It should be of 9.6 in support of 2012.

• Cannot start assistant in LabVIEW DAQ

  Hello

  I can't launch the LabVIEW DAQ assistant, but I can do it Max MAX DAQ's not flexible because I can't custom code or convert.  I tried all different ways to open the DAQ assistant and I finally realized something, on the block diagram, I open Tools/Advanced/Edit palette/Express/entry/data acquisition is missing (question mark) and many more functions are missing.

  I use the Labview 8.6 and NIDAQmx 8.7.1 evaluation software

  Can you please tell me what the problem is. I really need to launch of NOR-DAQmx, LabVIEW.

  Rgds

  Paul

  Hi Christ,

  Thanks for the fast service, I did as you said, but it didn't fix it. Basically, there are many media NI LV (8.5 and down) any brand with an X, I selected (highlighted) of Labview Signal Express support, since it was just the support NI LV as you said in the email (there is a message of side will not install it) then I click Next and finish ,. Reboot, lauch labview, move on to block diag/check on Experss VI on the function palette/entries, but lack even). I have als don't have reinstall Labview.

  I don't know if you have a plan B, because I'm stuck or if you can send me a screen shot or dialog of what I do; that will be great.

  Thank you

  Paul

• DAQ Assistant is not in LabView

  Hi all

  I use NEITHER cDAQ-9174 and NI 9203.  I have already installed the driver for the NI 9174 cDAQ, which is NEITHER-DAQmx 9.8.0.  I can see the device when I opened NI MAX. However, when I open LabView 2015, I can't find DAQ Assistant in the function Palette. I noticed on the chassis, 'ACTIVE' light is not on while two other "POWER" and "READY" light is on.  I look in the forums OR but I can not find the solution.

  Any suggestion, please help!

  Thank you!

  DAQmx 9.8 is not compatible with LabVIEW 2015.  You must use at least DAQmx 15.0.  See here for more details: NOR-DAQmx and LabVIEW compatibility

• Cannot get DAQ Assistant in Labview to cDAQ 9184

  I am trying to build a system for the acquisition of data with one NOR cDAQ 9184. I installed the drivers for the system and I'm able to get to the DAQ system using NI Max (under my system - devices and Interfaces - devices on network) and all channels appear well, however, I tried to follow the procedure described in http://www.ni.com/white-paper/11703/en/#toc2 to integrate my system with LabView and I am unable to find the tab software under the unit to be able to write the RIO 3.5.1 on the appliance and cannot find the device to through the LabView project.

  Your real problem is error-50103.  This is a common mistake, and you can find the answers for it if you are looking for in the forums.

  The problem is that you can't have several tasks (or several assistants DAQ) try to access the same device at the same time.

  Make a DAQ assistant who has all defined channels you wish to purchase.

• In Labview 8.5, what happens if the input signal exceeds the scope of the signal defined by the DAQ Assistant?

  Hi all

  This should be a pretty simple question, but I can't seem to find the answer online and currently do not have the functionality to test this:

  I'm using LabVIEW 8.5 and have a VI that imports data from sensor through the DAQ Assistant. In the configuration tab, there is a range of signal input. What happens if my sensor exceeds this range? I get a warning? The default value is the maximum (or minimum)? I was interested in writing a code to display an error that I approach the limits of this range, but did not know if I also need to include code to display an error if the scope is exceeded as well.

  Thanks for the help,

  Tristan

  Hello, Tristan,.

  The behavior depends on the selected range and the device you are using.

  If you are using a device with a single input range is valid, we will use this range, even if you set a smaller minimum and maximum in the DAQ Assistant.  So, if your device only supports ±10V and you set the range to ±8V, you will still continue to get valid data after your top sensor 8V until what you approach 10V.  When you reach the limit of the extent of your device, the output will be 'rail', and simply return the maximum value until the signal is less than the maximum value again.

  Note: A device that is nominally ±10V usually has a go-around (such as ±10.2V) which are usually specced in the manual.

  However, if you use a device with several ranges of entry then things become more complex.

  NOR-DAQmx player will choose the smallest range that entirely covers the interval you choose.  For example, suppose that your device supports the following input range: ±0.2V, ±1, ±5V, ±10V and you choose 0V - 3V as the range in the DAQ assistant.  The NOR-DAQmx driver will focus on the input range and the list of the entry lines that your hardware supports and choose the smallest encompassing the entire range that you set.  This would be the ±5V, because this is the only beach that contains up to 3V.  Thus, all between ±5V input signal is returned and none outside this range will be 'rail' to the maximum or minimum value.

  We do this because using small beaches make more efficient use of the resolution of the ADC.  So, we try to use the most effective range based on what you ask without picking up a range that will make you miss data.

  Let me know if I can clarify it more.

• Does not recognize NIPXIe 6535 while working in LabVIEW after selecting DAQ Assistant

  When you work in LabVIEW to generate a PWM Signal, need a DAQ Assistant either generate or acquire a signal. In the DAQ Assistant we must select the assesories as NIPXIe 6535 material or 6236 or 6711 to output the signal. During this process, only NIPXIe 6535 can be recognized. It has been a serious problem, so please suggest me with the remedies as soon as possible.

  1. No, you don't need the DAQ Assistant. You even don't need to use in a serious application! You need to learn to be programmed with DAQmx screws.
  2. When you can not select the module mentioned above in the DAQ Assistant, could also check you with MAX (Measurement and Automation Explorer)? You see this HW module in MAX?
  3. If MAX cannot recognize this module, you may have a driver problem. Have you installed all the required device drivers? Please provide the version of the OS and number of bits (64 or 32-bit), version of LabVIEW and number of bits, DAQmx version, etc. You can see the installed software and driver, Max under the heading 'Software' (fill in the list and make a screenshot).

• How to find the DAQ Assistant in LabVIEW student 2009 Edition

  I got 1 Core and Core 2 in LabVIEW 2009 prices in June. When I went to use the student edition I have LabVIEW 2009, I couldn't find the DAQ Assistant. This will present a problem when I come to use it in class this fall. It works fine on my version 8.5.

  You must install DAQmx, just like you had to do with 8.5.

• 201003-error occurred in the DAQ Assistant

  Hello. I use "cDAQ-9178" and "NI 9215" and "NEITHER 9402" are added on. "

  However, when I run Labview code, "Error-201003" occurs.

  {

  Device not available. Possible causes:

  Device is no longer present in the system / device is not powered.

  Device is turned on, but was temporarily without electricity / device is damaged

  }

  (Error appears as the 1st and 2nd figures below).

  (Plans of logic is the figure below).

  Thank you.

  I could be something with the pilot

  Check this box:

  Error 201003 to the MAX test panel or all by running the DAQ Assistant

  http://digital.NI.com/public.nsf/allkb/5413F392D88326148625746B006745C5

  In this forum, they speak the same error:

  Spontaneous error code 201003 for acquisition of data PCI configuration

  http://forums.NI.com/T5/SignalExpress/spontaneous-error-code-201003-for-PCI-DAQ-Setup/TD-p/830707

• Simulate signals wired to the DAQ assistant for USB-6009 device

  Hello

  I'm trying to send a signal to the DAQ Assistant Express VI.  I watched the movie "Generating a Signal" on the Web site of NOR (www.ni.com/academic/students/learnlabview/generate.htm) and I have my Signal simulate connected directly on the DAQ Assistant, as shown in this film.  In my case, the DAQ Assistant sends the signal to a device USB-6009.

  However, I received this message:

  Error-200077 occurred to the DAQ Assistant
  Possible reasons:

  Requested value is not supported for this property value. The value of the property may be invalid because it is in conflict with another property.

  Property: SampTimingType
  asked the value: Sample clock
  You select: On-demand

  If I select 'On Demand' in my DAQ assistant and run the vi everything works beautifully.  However, I need my DAQ assistant to be configured to generate a waveform AC continuous, not output a single alternating current rippling.

  What happens here?  I did not have this problem before on other devices of NOR. I am using LABView 2010.

  Please answer.

  Thank you.

  double post

• Under VI 'DAQ Assistant': Sub VI is not executable

  Salvation OR engineer,

  My task is to acquire and record data of input voltage analog with PCI-MIO-16-1 and BNC-2110 connector. I can get the signal via MAX, but as soon as I drop down the function palette DAQ assistant in FASHION Lab blocks diagram, my run button becomes broken. I got the error message like "Sub VI"DAQ Assistant": Sub VI is not executable. How can I overcome this?

  Thank you

  Yvette.

  Hi Paul,.

  Unfortunately, SignalExpress is a different license than LabVIEW. However, you don't need a SignalExpress to acquire and record data. LabVIEW has every ability to SignalExpress and many more.

  Kind regards

• Calibration of thermocouples in the DAQ Assistant, using data from spreadsheet?

  Hi all

  For my first application LabVIEW, I'm looking to automate the calibration of thermocouples by measuring their response at different temperatures in a dry well Sizer. I get temperatures of thermocouples six by SCXI 1303/1102/1600 and have six channels put in place in one of my subVIs in the DAQ assistant.

  I compare these values to temperature calibrator that I am acquiring by VISA series in an other Subvi. All these values are written in a .csv file.

  Can I import these data into the DAQ Assistant to use for calibration? Is there a simpler way to associate with the channel calibration data? Currently, I could manually copy - paste the cells on the worksheet in the calibration sheet, but that seems just silly.

  If there is everything that I could provide to help solve the problem, let me know!

  Thank you!

  Hi Zoysiamo,

  It is possible to automate the calibration screws DAQmx at a lower level, in particular the DAQmx channel property node. Using you can specify advance nationwide and the values on the scale for your channel. I recommend you take a look at this example of the community. The property node configuration will be similar to, as illustrated below: