LaserJet 400 m401dn: HP Laserjet 400 m401dn, make wireless?

Similar Questions

• LaserJet M1217: Error Scanner 22 with a Laserjet M1217 on a wireless network

  I just tried scanning a document using the SCAN TO PC.  It has worked well in the past.

  When I launched the scan, the M1217 was presented to work until the moment where the scanner arm normally begins to move.  I heard a 'click' plastic, then I got SCANNER ERROR 22.

  I followed the instructions on the FAQ section; disconnect the printer from the power, unplug the power cord, counted to 15 sec, plugged everything back in and NADA!  Re-error.

  Advice?

  Hi @hadrian9637,

  Welcome to the Forums of HP Support! I read your post and see that you are getting the error "Scanner 22. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Please try the steps outlined in this document, they are little different from what you have described, HP LaserJet Pro M1212nf and M1217nfw Multifunction Printer Series - a Message "Scanner Error 22" appears on the printer control panel.

  Please keep the lid of the scanner open and then press the copy button.

  Check if the scanner lamp turns on.

  Also to see if the scanner moves freely through the glass.

  It may be a hardware problem.

  If the problem persists, please Contact the HP Support for help. Check the model number and the form to receive a file number for faster assistance. Good day! Thank you.

• HP Laser Jet Pro 400 M401dne: HP Laser Jet Pro 400 M401dne installation wireless, how?

  How to set up the configuration for this printer Wireless:

  HP Laser Jet Pro 400 M401dne

  I connected via the network. I installed the software on a client computer running Windows 7 Pro.

  I used the utility to reconfigure the setup and the utility (which came with the printer and has been updated to the latest version) does not give me the ability to connect the printer in wireless mode.

  According to the data sheet, the M401dne model is not supported wireless connection:

  

• LaserJet p1505 for connection wireless printing

  I have a Laserjet P1505 (not 1505n) a Net Gear N600 dual band Router router with USB port and printer. I tried to connect the printer USB cable to the USB port on the router and installed the printer on the laptop (a Windows Vista) I'm trying to save up for a wireless printing capability. The updated drivers from HP Web site, set to turn on printer 'sharing' but the printer does not appear in the network and sharing Center. Have directly connect the printer USB cable to the computer laptop USB port to print from the laptop.

  I missed something or cannot print via the router P1505 (without the "n")?

  Thank you

  I found a post where a similar problem has been resolved. The user has enough to show what he has done to help others like you. I hope this helps.

  OfficeJet 7210 won't install with Netgear N600 router

• LaserJet pro m177fw mfp: wireless connection to install

  I have a laptop of my work that is not a hard drive software to installthe to connect wireless to the printer. I was everywhere on the hp Web site to find a link without success. How can I get the laptop wireless connected to print to this printer without having to use the disc.

  Hello

  Please download the following drivers & the software and install it on your computer:

  http://ftp.HP.com/pub/softlib/software12/COL51592/kJ-124901-3/Color_LJPro_MFP_M177_full-solution_13295.exe

  More software and tools: http://support.hp.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443#Z7_3054ICK0KGTE30AQO5O3KA30R1

  Kind regards.

• LaserJet P1102W (Wireless B & W): [Laserjet P1102W (B & W wireless)] not able to print (local error)

  Hello

  When I try to print something, that is to say the word, it says I can't because of "interference by user" (translated from Dutch). Sometimes a Windows 10 notification also, saying "the printer requires attention" or something. Here are a few screenshots (in Dutch)

  Spoiler (Highlight to read)

  It is in Word. Translation: ' interference by user: 1 the document in the queue. "

  It is in Word. Translation: ' interference by user: 1 the document in the queue. "

  Spoiler (Highlight to read)

  
  It comes to the print queue of the printer window. At the top it says "... P1102w) - Attention required "

  It comes to the print queue of the printer window. At the top it says "... P1102w) - Attention required "

  As you can see I'm getting 2 different error messages, but I have no idea on what step I need to take next. I tried many things such as removing and adding the printer, firmware update (however HP program is quite vague, so I don't know if I've done this good), etc. of Windows updates.

  There are several devices that use the printer (including other users of Win10) but I'm the only one with this problem so I am convinced that it is a local error. I got the error a few weeks now, but still no improvement.

  Thanks for reading,

  Yos

  I've tried, but it did not work. I found a solution, although I'm not entirely sure of what went around or causing the problem.

  First, I tried to reinstall the printer software/driver (?) that you usually get when you enter the IP address of the printer and the HP smart install. I got the software from my brother who put it on my pc by Onedrive and e-mail. However, I could not run the file because Windows somehow he blocked for security reasons because the developer has not been approved. I couldn't disable the blocking, so I did some research on Google. I read something about a hidden administrator account, you can activate, but decided to wait a bit.

  Apaprently, as of yesterday, no one could use the printer (although my problems before that). We found his IP address online so I plugged the USB from the printer directly in our modem. Then he has been brought back online, and he remained in line when we removed the USB later.

  I had activated the administrator account "secret" (assuming that it is some kind of hidden because it took activation CMD) where I downloaded the printer driver by entering the IP address in the browser on this account. Don't know how or why, but then I was able to print again.

  I don't know if you need to turn on this admin account to fix or if this file is a solution in the first place, but I solved the problem.

  -Yos

• Add LaserJet 1525nw to the wireless network

  Hello

  Since I update my router for the Cisco E3200, it seems that my printer laser color 1525nw spray can not register to the router. I tried the router WPS button to find the printer and the PIN method, but both failed. Can someone please help me get the printer connect to the router wirelessly? I work in an office environment at home.

  Thank you very much.

  I'm not entirely sure as to why this happens.  In some cases, restore the network by default before the WPS option used.

  On the printer, go to network settings > network by default.  This will reset the network outside the parameters of the box.

  Go to network setup > Menu wireless > wireless on / off and check the wireless radio is on.

  Once it is completed, repeat the WPS configuration by going to Network Configuration > wireless Menu > Setup WPS to prepare the printer to use the router WPS button.

  Let me know what happens.

• LaserJet P1102W: INSTALLATION p1102w WIRELESS: does not detect my USB connected during installation

  I am in this picture and I can't do the installation to continue, even if I'm sure that there is nothing wrong with my USB port.

  I tried to use the same cable / usb port to print from the printer and it works.   but that's just for this installation wireless, doenst work.

  Help.

  

  Hello

  This can happen due to connection of USB oprior the installation of the software.

  In the devices Panel and printers, right-click on any instance of your printer and select remove device.

  Allow it a moment, if nothing happening try removing and reconnecting the USB after the specified screen.

  If you have already stopped the installation, don't forget to remove any existing printer device and unplug the USB, then follow the installation once more and connect it only when necessary.

  If it persists, click the background area of devices and printers and select Device Manager, is there any icon marked in different categories?

• LaserJet CP1525nw: Claer'style Wireless configuration - Laserjet CP1525nw

  I had to replace a router in a neighbor's House, they used the object connected wireless printer.  The new router has forced me to change the password for the connection Wireless which was previously used.  The same SSID IS used on the router again.  I tried all attempts to reset the network settings on the printer, and whenever I do, and then repeat the wireless configuration, whether through WPS, PIN or CD-ROM and USB cable, in all cases, the connection fails and in the best case said security password is wrong or in the most serious cases that the printer is NOT the CORRECT wireless network.

  More bizarre, set part aside from the absence of a solution on the forums of HP, or in the manuals, is that the printer keeps picking up an odd-ball, "HPCP1525-135f8d" SSID, mode is ad hoc and the INVESTIGATION period comes up with a "fake" number that does NOT correspond to a local network, 169.254.123.35.  I've seen IP like this before on the PC NIC cards that can not connect, I think that it's some sort of IP assigned internally, not any network device.  That combined with the fake SSID, I am convinced that the printer is at the origin of these BAD configuration data.

  I tried to manually set the IP address, using a reserved IP address on the router that I've set up just for this printer.  Still nothing, it fails to connect, and collects and records this bad SSID and IP.

  How the h * ll get you the NVRAM on the printer to remove this IP and FORGET that SSID?

  Don't tell me to re - run the installer, I tried several times, which can temporarily erase data, but by re-running the installer again collects and RECORDS the wrong configuration data.

  My best guess, and another solution that cannot be found ANYWHERE, is how do you do a HARD reset printer factory?  I had about my fill of the usability of these interface software and setup of HP!

  Help!

  I found this on a post above and it works for the person.  You must first connect the printer with an ethernet cable to your network router properly available ports and then follow the instructions below:

  The non-taureau * beep * way to Setup your HP CP1525nw for Wireless Printing

  1. 1. Connect the printer to your router via an ethernet cable.
     2. At this point, you will need to navigate through the LCD keys and a printer to the network installation. It is a simple menu tree that you access via clicking on the arrow buttons and clicking OK. Simply connect via Ethernet and use the DHCP protocol. It needs to connect to your network.
     3. Once the printer connects to your network, it will display its IP address on the printer's built-in LCD display.

     Enter the IP address in a web browser on a computer that is on the same network. After clicking on enter you will be presented with an administration interface based on the web for your printer.

     1. Click on the tab 'network '.
     2. Click on "Wireless Network Configuration" in the options on the left.
     3. Status should be 'ON '.
        Configuration method must be "join an existing network.
        Name of the network is expected to present a list of available networks. Click on yours.
        Authentication should be set according to your network
     4. Click on APPLY and disconnect the wired connection to the router. The little light on the front of the printer wireless flashes because it connects to your wireless router. Once the light is solid new IP address of the printer should be displayed on the built-in LCD screen.  You should now be able to connect using this ip address.

• HP Laserjet Pro M176n MFP: HP Laserjet Pro M176n on wireless network MFP?

  The difficulty in trying to get this printer on a wireless network. There seems to be available to set up the printer using the options available in the screen of the printer on a very limited help.

  Once that you have connected the cable to your router, insert and launch the Elf Setup.exe printer installation CD or download the latest version of the software from the HP site.

  If the software was already installed select adds another device and follow the steps, and then select a network connection once asked you how you connect to the printer.

  If you do not install its software yet the followed by the installation wizard until you saked how to connect the printer and select "through the network.

  If necessary, you can download the software of the printer below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=kJ-124897-3&cc=us&DLC=en&LC=en&OS=4063&productOid=5303439&sw_lang=

  Kind regards

  Shlomi

• LaserJet M252: Laserjet M252 wired and wireless

  I have a user who has this printer and I would like to know if this printer can be configured for a WIRED connection and wireless.

  The user has a Macbook Air, Chromebooks and iPads.   I configured the printer to have a static IP as a wired for the MBA and Chromebooks can be printed on it.  IPads need a wireless connection.

  Since I have already assigned a static IP address for a WIRED connection, configure the wireless as DHCP for iPads can print?

  You're right, plug an ethernet to the printer cable disables the wireless radio.

  Kind regards

  Shlomi

• LaserJet MFP M277 Pro: Unable to connect wifi on lacerate pro mfp m277

  My new printer is connected ok to my mac.

  But I can't set up wireless for laptops may not print. When I go to the wireless Assistant, he gives just a message saying "Receive information from wireless network" and this message stays on the screen indefinitely. The rest of the time, no wifi sign is on the touch screen.

  Hey @HJW1,

  Welcome to the Forums of HP Support!

  I see that you encounter some problems with the connection of your series M277 Laserjet Printer to your wireless network. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:
  Turn the printer off.

  While the printer is turned off, disconnect the power cable from the back of the router for a minute.

  When the lights come back on the router, turn on the printer.

  After the above, you should be able to connect the printer to your wireless network. If you can't, please let me know what happens when you try to connect to the network now. If you are able to connect, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Canon EF 70-200mm f/4 L not as strong as mycanon account EF 100-400 mm f/4.5-5.6L USM IS

  Hi can't seem to get a strong an image with my 70-200 that I can with my 100-400 mm. should I get equally sharp photos with two glasses. I still have a warranty with best buy.

  What are your shooting conditions?  If you were less than 1/400 or the IS on the 100-400 could make a significant difference.  Try a controlled test, on a tripod, same settings, IS off.

• HP Laserjet CM1415fnw wifi scan

  I am seriously thinking to buy this printer, but before I would make sure that HP Laserjet CM1415fnw can scan wireless.

  I really don't want to use the usb cable.

  Thank you

  Felipe

  I did buy and the answer is YES, you can scan wireless. It's a very nice printer/scanner.

• HP LaserJet P1102w worked very well and now just print 1st page of multi-page documents

  Hi, I used my printer for more than 6 months.

  Last month, has had the problem for a couple of days, then he went suddenly (yahoo, I thought).

  Has started again last night when printing pdf documents, it only prints the first page and then it seems stuck on page 2 (52% complete transfer appears on the windows printer).  For word, it seems to just take forever to print other pages...

  Running on a Mac OX X Yosemite.  Printer is connected with a wire (I was never able to complete the wireless connection and got too busy to spend more time understanding...).

  Tried to turn off my computer and then restarting him.  Also stop the printer and restarted.

  Thanks in advance,

  M

  Hi @MartineRB ,

  I see you are having problems printing multi-page documents. I would like to help.

  Fix permissions of the drive on the Mac:

  Close all applications.

  In the Apple menu, click OK, click Applications, and then click utilities.

  Double-click disk utility.

  Highlight your hard drive / partition on the left.

  Click on check and then repair disk permissions.

  Restart the computer...

  Reset the printing system:

  Note: This will remove all printers in the print and Fax/Scan, any printer deleted can be re-added later by clicking the sign plus (+) symbol.

  Click on the Apple icon and then click on System Preferences.

  Click on Printers & Scanners.

  Make a right click (or Ctrl + click) in the left white side panel, and then click Reset printing system.

  Click OK to confirm the reset.

  Type the name and the correct password.

  Click OK to reset the printing system.

  Then click on the sign to add the driver, highlight the printer +. (you may need to click the drop down menu to select the printer name) Then click the Add button.

  Try to print again.

  If you are able to print now by the USB connection and want to set up the printer on the wireless network, take a look at the following:

  Restore the default settings of the printer.

  Turn the printer off, press and hold the wireless button and the Cancel (x button) button while turning the printer on and do not release both buttons until the printer stops making the noise.

  Print a configuration report and check the SSID address and IP are disabled.
  Printing a Configuration Page. Select the method two.

  Make sure that Safari is set as default browser. Sometimes, the built-in Web server will not open if it is not.

  Open Safari, at the top, select the Safari menu, select Preferences, general, as a default value.

  Here's a Youtube video of the Laserjet P1102w on Maverick wireless installation.

  LaserJet P1102w.

  You can follow the steps instead of the video.

  You must connect the USB cable from the printer to the computer to install the printer as a USB device first and then to configure the wireless network.

  Turn on the printer, connect the USB cable and install the update from Apple that should load automatically.

  Then go to the Apple, system preferences, printers and Scanners.

  Highlight the Laserjet on the left side of the window.

  Then click Open Print Queue, click settings, click utility, click open printer utility, then click the button HTML Config.

  The integrated for the printer Web server opens.

  Click on the network tab, select Wireless on the left side.

  Fill in the information for your network. Status make sure that you select enabled.

  Apply the settings.

  Then go back to the Apple preferences system, printers, and Scanners and click the + to add the Hello Laserjet Printer. (may take a few minutes to appear) Make sure that the printer is listed beside the use: displays the name of the correct printer and not the driver by default, and then click the Add button.

  Remove the USB printer in the list of printers and Scanners window.

  Unplug the USB cable.

  Test the printer.

  If you need help, let me know.

  Good day!
  Thank you.