LaserJet 8150n: configuration network laserjet 8150n

Similar Questions

• Configuration network LaserJet P1606dn

  Hello world

  I have a problem with establishing a new LaserJet P1606dn on our network. The installation software provided with the printer assumes the environment uses a DHCP server to obtain an initial IP address and then you can evaluate the printer through the web interface and change it. My problem, we do not have DHCP on our network and I need to set up an IP address on this printer. My question, is there any other utility that can be used to find the printer, and then set the printer with a static IP address.

  Thank you in advanced for assistance.

  Steven

  Too bad. I found another way to access the printer. It seems to have assigned the printer an IP 169.254.x.x wherein I changed my desktop to the same subnet and then access the printers web interface to configure networking for the correct IP subnet.

• How can I configure network server in blackberry phones smart blackBerry bold 9700

  How can I configure network server in blackberry bold 9700

  I want that my third-party applications to access the organization intranet using your organization's network.

  When I tried to change the permissions of third-party application, it shows RIMconnections, interactions, data from the user... don't allow, deny permission is there.

  How can I set thesehttp://docs.blackberry.com/en/smartphone_users/deliverables/23895/Third_party_application_connection...

  Yes, if you read the link you posted, these settings are for OS6 and higher devices.

  Not for OS5 and you're on OS5.

• A web site with the IIS configuration network location

  Is there information on how to set up a web site to a network location.  I have a shared directory of Mac that I have access to my Windows Vista pc.  I have a Server IIS Web on this PC and want to test the Mac files with the IIS Web server on the Windows computer.  I created a site in IIS and pointed on the shared drive, this resulted in an error: cannot read the web.config configuration file.  I tried a different approach: create a local site to wwwroot, then create a virtual directory.  This brought the same error: the requested page cannot be accessed because the configuration data of the page are invalid.  I have IIS 7 on Windows Vista Business Edition.

  Hello

  Your question of Windows Vista is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the forums of IIS. Please post your question in the following link for assistance:

  Link to the forum:

  http://forums.IIS.NET/1047.aspx

• error windows cannot configure network adhoc connection? win7home premium

  in network and sharing Center I select new connection > network configuration ad-hoc (computer to count) name network and fill all boxes and press enter then I get windows error could not set up 'network name' I adapter.plz wireless brodcome802.11g give me a solution a solution.thanks perfect

  Hello

  1. when exactly do you get this error message?

  2. have there been recent changes to the computer before the show?

  I suggest you to see link and check if it helps.

  Error message when you try to connect to an ad-hoc connection Windows 7 or Windows Vista: "Windows cannot connect to ": http://support.microsoft.com/kb/946481

  More information: Set up a computer-to-computer (ad hoc) network: http://windows.microsoft.com/en-US/windows7/Set-up-a-computer-to-computer-ad-hoc-network

  Hope this information is useful.

• Access restriction configuration network devices with the level of the ACS 5.0 user

  Hi Experts,

  I have some configuration tasks TACAC with level of different user for all routers and switches,

  To further develop, I engineer, analyst and site engineers, so I want to configure centralized authentication with Annie tacac different levels for the various categories of network engg. Analyst, site engineer,

  can someone explain about how to proceed with ACS 5.2 and what configuration is required at the peripheral level.

  I'm particularly looking for the 5.2 acs configuration procedure.

  Looking forward to get the answer.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/policy_mod.html#wp1076053

  In "default device admin" just create authorization rules.

  They should look like "If the user/group type = site engineer, then assign the shell profile X.

  You then define the profile of shell in the elements of policy and put in there all the privileges of your engineer to site.

  And so on for the other roles

• Configuring network DMZ, internal using Nexus 1000v

  Hello peoples, this is my first post in the forums.

  I am trying to build a profile for my customer with the following configuration;

  4 x ESXi hosts on the DL380 G7 each with 12 GB of RAM, CPU Core X 5650 of 2 x 6, 8 x 1 GB NIC

  2 x left iSCSI SAN.

  The hardware components and several design features, on that I have no control, they were decided and I can't change, or I can't add additional equipment. Here's my constraints;

  (1) the solution will use the shared for internal, external traffic and iSCSI Cisco network switches.

  (2) the solution uses a single cluster with each of the four hosts within that group.

  (3) I install and configure a Nexus 1000v in the environment (something I'm not want simply because I have never done it before). The customer was sold on the concept of a solution of cheap hardware and shared because they were told that using a N1Kv would solve all the problems of security.

  Before I learned that I would have to use a N1Kv my solution looked like the following attached JPG. The solution used four distributed virtual switches and examples of how they were going to be configured is attached. Details and IP addresses are examples.

  My questions are:

  (1) what procedure should I use to set up the environment, should I build the dvSwtiches as described and then export it to the N1Kv?

  (2) how should I document place this solution? In general in my description I will have a section explaining each switch, how it is configured, vital details, port groups etc. But all of this is removed and replaced with uplink ports or something is it not?

  (3) should I be aiming to use a different switch by dvSwitch, or I can stem the heap and create groups of different ports, is it safe, is there a standard? Yes, I read the white papers on the DMZ and the Nexus 1000v.

  (4) is my configuration safe and effective? Are there ways to improve it?

  All other comments and suggestions are welcome.

  Hello and welcome to the forums,

  (1) what procedure should I use to set up the environment, should I build the dvSwtiches as described and then export it to the N1Kv?

  N1KV replace dvSwitch, but there isn't that a N1KV ONLY where there are many dvSwitches N1KV would use the same rising in the world.

  (2) how should I document place this solution? In general in my description I will have a section explaining each switch, how it is configured, vital details, port groups etc. But all of this is removed and replaced with uplink ports or something is it not?

  If you use N1KV you rising the pSwitch to the N1KV.

  If you use dvSwitch/vSwitch you uplink to the pSwitches to the individual dvSwitch/vSwitch in use.

  (3) should I be aiming to use a different switch by dvSwitch, or I can stem the heap and create groups of different ports, is it safe, is there a standard? Yes, I read the white papers on the DMZ and the Nexus 1000v.

  No standard and Yes in many cases, it can be considered secure. If your existing physical network relies on VLANs and approves the Layer2 pSwitches, then you can do the exact same thing in the virtual environment and be as safe as your physical environment.

  However, if you need separation to the layer of pSwitch then you must maintain various vSwitches for this same separation. Take a look at this post http://www.virtualizationpractice.com/blog/?p=4284 on the subject.

  (4) is my configuration safe and effective? Are there ways to improve it?

  Always ways to improve. I would like to start looking into the defense-in-depth the vNIC and layers of edge within your vNetwork.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, 2010

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• Configuration network problem

  Hello world!

  I have the following Setup: a virtual server with network three ports eth0 and eth2. eth0 is used fpr administration of the VServer.

  eth1 is disabled. Now, I have configured eth2 as a bridge to the virtual machines. For now, it works pretty well with

  exactly one IP configured on the host computer for eth2. Now it is true that there are several more mapped IP addresses

  on eth2. The amount of these IPs may change over time, and I don't want to configure the interface on the host

  whenever I listen to new addresses. These IP addresses are all on the same network using the same program and

  subnet and gateway. So my question is:

  How should I configure eth2 on the host (debian) system for all incoming traffic on eth2 is filled to the virtual machines?

  Thanks a lot for your help.

  orkano

  PS: Here is my file interfaces:

  This file describes the network interfaces available on your system

  1. and how to activate them. For more information, see interfaces (5).

  1. The loopback network interface

  Auto lo

  iface lo inet loopback

  1. The main network interface

  Auto eth0

  iface eth0 inet static

  address XXX. XXX.226.101

  subnet mask 255.255.252.0

  dissemination of XXX movies. XXX.227.255

  Portal XXX. XXX.224.1

  Auto eth2

  iface eth2 inet static

  address XXX. XXX.246.10

  netmask 255.255.255.0

  dissemination of XXX movies. XXX.246.255

  Portal XXX. XXX.246.1

  Welcome to the forums!

  orkano wrote:

  How should I configure eth2 on the host (debian) system for all incoming traffic on eth2 is filled to the virtual machines?

  You must run ' vmware - config.pl ' to configure virtual networking. Then you choose eth2 as your adapter to fill. That's it for the side host. The customer must have a vNIC, type "bridged" and their own IP configuration valid IP range of the physical network subnet where eth2 is attached to.

  That answer your question, or have I missed something?

  AWo
  VCP / VMware vEXPERT 2009

  = Due to a lack of employees, human beings humans are working here. -Treat it with care, they are rare. =

• Configuration network ESX 3.5 and Appspeed

  I have 3 vswitches and a few groups of ports for different VLANS. If I want to install AppSpeed on esx 3.5 do I need create another vSwitch, port group and put in mode promiscuity with all the natachasery so I can monitor other vswitches and port groups? Or it walk straight on the box without these configurations and probe handles the network part? Need help please, I want to test so I can buy it and if someone has the best practices or configuration, feel free to share.

  AppSpeed creates groups of new promiscuity port dedicated for the selected vSwitches. Please note that in all cases, it does NOT change the configuration of the physical network adapters or any other port groups existing settings.

• How to add the device (eth1) after the command 'neat' calls 'Configure Network'?

  People,
  
  Hello. I want to install 2-node RAC Oracle 11 GR 2 VMPlayer 3 System. The host OS is Windows 7. Oracle Linux 5.6 is the guest operating system. 2 nodes (2 Virtual Machines) are RAC1 and RAC2.
  
  We must create the public IP address and IP private for each virtual computer (RAC! and RAC2). IP addresses public (eth0) connect RAC1 and RAC2 of shared storage. The private IPS (eth1) connect RAC1 and RAC2.
  
  In Oracle Linux 5.6, the command "neat" to the root user calls the configuration of the network (5 tabs) as follows:
  
  Devices | Material | IPsec | DNS | Hosts
  
  In the "Devices" tab, I created the public IP address for RAC1 whose nom_peripherique is etho.
  But I don't know how to add another device 'eth1' in the 'Devices' tab to create the private IP address.
  Thus, the network cannot be implemented.
  
  Can any folk tell me how to add another device (eth1) in the 'Devices' tab after the "neat" command calls "Network Configuration"?

  user8860348 wrote:
  Folk,

  Hello. Thanks much for the reply.

  In the directory "/ etc/sysconfig/network-scripts", there is a file 'ifcfg-eth0"which contain a public IP address.

  But there is no file "ifcfg-eth1" that must be a private IP address.
  What is the reason that there is no device 'eth1' in the 'Devices' tab in the Network Configuration window?
  Do we need to create a file 'ifcfg-eth1 '?
  What should be the content of 'ifcfg-eth1 '?

  Did you create a second NETWORK adapter to the virtual machine?

• configuration network on VMWare server 2

  Hello

  I installed Vmware server 2 on my server (WIN2k3 with nic 2s because my server have a role of routing). A NIC is set up for INTERNET and other NIC is set to INTRNET.

  the configuration of my INTRANET is on class C IP:192.168.99.XX, SM: 255.255.255.0. I create a virtual Instalation with UBUNTU 8.10 Server... I installed UBUNTU with no problem and without error, but without internet access because I don't know what ip and network configurations I should do on virtual NIC (Vmnet1 and Vmnet8) and which configurations should I do ifconfig on UBUNTU (IP, SM, gateway, DNS)

  can someone help me?

  Thank you.

  Depends on...

  I'll explain what these networks and you can find what you need:

  1 bridged (VMnet0)

  If the virtual NIC (vNIC) is fulfilled, the guest takes part like any other host on the network. It needs its own IP address corresponding to the IP network to which it is filled.

  2 host-only (VMnet1)

  It is a network isolated between the host and the guests. No outside communication.

  3 NAT (VMnet8)

  When you use this type the host acts as a proxy routing with address masquerading. This means that all packets send by the client appears to come from the host to the outside world. You can hide your comments like that.

  What physical adapters is used to fill can be configured. The default value is one automatically chosen NIC jumpered to VMnet0. You can create a custom network (say VMnet2) and he a teddy bear additional bridge.

  Networks VMnet1 and VMnet8 can be served by the DHCP of VMware Server, so if you use this type of vNIC and you configure the IP address in the guest to use DHCP, you're fine.

  Don't forget to use a firewall at least on the vNIC which can face outside if you use bridged or NAT to connect to the Internet!

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!

• Win 7 Pro 64 bit configuration network, cannot access card reader when im not connected network

  IM under Win 7 Pro 64 bit on my laptop, im am Setup on an Exchange to my office network. The laptop has an SD card reader, and since I use CF cards I have a USB card reader also (my old card reader has been pre Win 7, so in desperation, this last weekend, I bought a new Targus card reader that preload drivers and is Win 7 compatible.

  The question is when im not connected to my office network and I put an SD card in the embedded player, or use the USB drive (the old drive did the same thing if it is not a drive issue) the computer laptop reconizes the event by sound in my computer scans the URL bar, and the card will not appear in the my computer window. So im hooked on my network it readings, launches autoplay and wonder what to do (as I have it setup to do).

  I always perform software updates and just checked my Windows is up-to-date.

  Any ideas as to what is happening and how to fix?

  Thank you

  Hello

  I suggest you to send your request to the below thread to get assistance on this issue.

  http://social.technet.Microsoft.com/forums/en-CA/categories/

  It may be useful

• Cannot configure network for POS

  Hello

  I managed to import of the FVO, logged on to the web client with default password, the pick-up system (ip, dns, gateway), correct information that I have inserted during the import, I put the additional host name and domain name information, and then click Next.

  A guarded error message appeared-> "IP/DNS cannot be resolved, please double-check the hostname, DNS and domain for validation of research forward and reserve."

  I then connect to the consolse, the ping to the DNS server, the domain name of ping, ping gw and all what it seems to be okay. I also tried to modify the hosts on server file and manually insert the dns server and the name of the host, the error still there.

  An advise please.

  Thank you

  Hello-

  In the administration of POS Guide, it indicates that the DNS server must support direct and reverse search.  It also gives steps to determine if DNS is configured correctly (see page 13-14).

  http://pubs.VMware.com/vSphere-51/topic/com.VMware.ICbase/PDF/VMware-data-protection-Administration-Guide-51.PDF

  I hope this helps.

• Configuration network/questions redundency

  I have a host who complains the message "Host ESX currently has no management network redundancy" in the Summary tab.

  I have 2 cards connected network. I tried to disable one by one and receive a response form a host.

  What Miss me?

  Hello.

  See KB 1004700.

  Good luck!

• Best practices for configuring network ESX

  Suppose I have a small resource ESX server with only two physical network cards to work only a few virtual machines.  There are only two physical network adapters cannot be added.  Still, best practice would dictate that this service console would be on its own dedicated physical NIC?  In this scenario puts service console and all the VMs on a pair of network cards grouped better because if a NETWORK card fails both the service console and all virtual machines are still available?  In this case the bandwidth is very low and contention for the network bandwidth is not a problem. Thank you

  Hello.

  Check out "Blue Gears - 2 with VMware ESX physical NIC" of Edward Haletky for some good info on it.

  Good luck!