LaserJet Pro 400m401n: Service error 79 HP Laserjet Pro 400 m401n
Service error 79 error code.
Printer does not print Web sites or the other. Authorized the printing that and restarted, same thing. Sometimes stopping and restarting with to produce a page. I tried to reinstall the driver. NO GO.
In addition, it seems that everyone in this forum to have this same problem Service error 79 are on a network. This printer is NOT connected to a network. It is only connected to a desktop computer at home via the USB port. If I disconnect the USB and power Off / On, it does not show an error. The computer is running Windows 7 PRO.
Any help would be appreciated until I throw this thing out the window.
Thank you!
T.
Suggest you do the following as it works very well without connection to the pc. I would completely remove the printer from the computer and if you have the original disc supplied with the printer, use the scrubber on the disk utility to delete all files for the printer. I then turn off the computer, turn it on and reload the printer according to the instructions from HP. After the printer is busy, I would download the latest firmware version for your operating system and to update the firmware and see if the problem has been resolved. Most of the time the 79 issue is caused by a bad print job which confuses the printer and makes the error. A bad print job most of the time is caused by trying to print a web page that contains the latest code that your firmware version is not satisfactory if more aged. Sometimes pdf files can cause a problem and generally using the postscript driver will solve this problem. Good luck.
Tags: HP Printers
Similar Questions
-
I am connected to ePremis (medical site) that allows me to print the selected medical forms. ePremis uses the default printer to print the selected form. The selected form should be printed on a preprinted form that I load into the tray of the printer.
The problem is that ePremis does not provide an option to set gutter margins and print aligns correctly with my pre-printed form. The print position is a little weak and must also be shifted a little to the left. I need to reduce the high binding margin to move the position of superior print on the page and the left binding margin must also be reduced to move the print a little position to the left so that the printed data will properly align with my pre-printed form.
Since ePremis does not offer an option to set the margins of the gutter, I need to be able to set the margins of the gutter through the printer driver, but there is also no option provided by the printer driver dialog box to set the margins of the gutter. :-(
Is it possible to set the printer LaserJet Pro 400 gutter margins? I see the margins left and right options in the driver dialog box printer, but they are grayed out and cannot be changed.
I have another printer, Kyocera laser printer, and I don't have this problem with the Kyocera because it offers the possibility to set gutter margins in the printer driver dialog. I wonder why the LaserJet Pro 400 does not provide this option?
I perhaps could solve this problem by sending PCL6 commands to the printer before printing? I'm a programmer and am open to this option if it would work.
Your help would be much appreciated. Thanks in advance!
Setting margins generally depends on demand - but (you say) that your application does not allow this.
Some printers provide functionality of saving images , whereby the position of the image of the page onto a physical sheet can be adjusted to the printer, usually on a basis of by-tray.
For example, with my Laserjet Pro MFP color 400 M475dn, the appropriate menu/menu item is described as follows:
Note:
- This setting applies to the bar up this that changed, so will have an impact on all the tasks using the specified status bar.
- Not all printers support these features - I have no idea if your LaserJet M401 exercises or not.
With regard to the '... sending the commands to the printer before printing... PCL6«» :
- PCL6 (PCL XL) rather more autonomous than PCL5is, so I'm pretty sure that nothing you can "send" to the device to influence the outcome of the following printing.
- Even with PCL5 print jobs, standard printer drivers are "overcome and-tail' with universal output language (UEL) escape sequences (which reset the device to the market environment (user - default)), which would be too mount sequences exhaust specific PCL5 previously sent to the device.
-
Hello
In my office, we use the printer HP Laserjet Pro M401n. about 5 to 10 users, the printer is on a network and not connected to a PC. Is that several types of fonts do not print , only the border is printing. Replaced by a new cartridge. The question is always the same
>> .. Is that several types of fonts do not print , only the border is printing...
You will need to provide more information in order to wait for the appropriate advice.
For example:
- Is the problem limited to an application (such as Word) documents or multiple applications or applications?
- What do you mean by "types of fonts"?
- Do you mean different fonts (fonts strictly) for example Courier, Arial, Times New?
- Or do you mean for example regularly, different variants of Bold, Italic, BoldItalic?
- Or something else?
- Can you provide a scan of an example? Use the the "insert/edit image" button to insert an image in a post (this may take up to 48 hours to "approve" until it's visible to others).
-
Printers HP Laserjet Pro 400 M401n
When I plug the USB stick into the port on the computer, it goes into devices and printers as an optical drive instead of a printer. For this reason I can't get the drivers to install.
Sounds like you need to do is to disable the "smart install"...
First, remove the optical drive...
On the printer, go to the service menu... then left to installing smart arrow... Be sure to turn off and save the OK
button...
Now... power cycle the printer... and it must be set up as a printer 401...
Advise if it suits it...
-
LaserJet pro 400 m401n: where is the power button on m401n laserjet pro 400
Sorry for this stupid post but:
Well, I unpacked it M401n and pluged and attached to the computer via hard wire, and
put the paper of soe and was about to embark on the end of the software of the job, but theere are no nights on
on the pronter. With power applied, I expect some kind of fire on in the small window on the top?
I've linked the red x button and ok and others, but I can't get any sign of physical life out of it. I tested only the
out of the wall was live.
Thank you - got the power and the initialized cartridge. Thanks (as emily Litells would say-Never Mind)
-
Service error 49 - Turn Off, then on - LaserJet Pro 200 M276nw
I was the addition of another post for a different printer but didn't want to Miss anyone with MY printer problem.
UPDATE * (at least for my LaserJet Pro 200 M276nw)
I found the cause but will need help from someone at HP to "solve" this one...
My new guard M276nw throw a 49 Service error, CAT has given a lot of power, voltage on, wait, try again blah blah blah, blah blah fuser problems. 10 minutes from the forum search put me on possible wireless network issues with other printers and the SSID. Anyway after regaining a printer Staples and saw the problem coming up again on a new another brand... I tried the search Forum and Tada! at least I was able to find a cause.
I have a D - Link DIR-825 wireless router. He has dual band (2.4 GHz and 5 GHz).
Normally I enabled for the multitude of devices that people have these days in my house.
I updated the firmware to the last update (20121026) and then restarted.
Roger restarted shortly after error Service 49.
Then I disabled the two strips to test each independently wireless band.
The printer acted normally so I decided allow each band separately.
When I turn on the 2.4 GHz band in the router, the printer immediately throws an error in Service 49.
I tested several times (5 to be exact) and every time when the router restarts the printer says error.
So, I left off 2.4 GHz band and then the 5 GHz band.
I activated the band 5 GHz 3 times and turned off and found no effect on the printer (at least in a 5 minute window).
So now I'm left with only a single band wireless router or printer who likes to turn on every 20 minutes or more.
There is probably a setting (or 2) which can be changed in the router or printer that can prevent this (I hope).
I just need to find the right person in HP...
I should have updated this thread I'm sorry, but I found myself updated the same problem on another thread of printer M251nw, since someone has answered that one. I have to keep that one thread - sorry, but it seems to me that I just heard another as well, but for a m475dw as well. Maybe the same problem that I don't know.
Anyway to update my m276nw situation: After experimenting for a while try to limit I decided to eliminate the possibilities by disabling my router another suggestion of posters to remove the printer from the wireless environment and reset to factory settings. So I turned off my 2.4 GHz band in my router (leaving 5 GHz active), reset the printer and it was sitting still (no reset), he even went to sleep normally. I turned on the 2.4 band and the printer immediately threw the error repeated tent kept the same result no way to leave on the 2.4. The next day so I decided to check my router and found 2 year old firmware. It took several updates to get current and on the last I didn't reset the printer to the factory again and there's no error yet. The printer acted normally for a week, he normally sleeps and wakes. It was turned off (on purpose) a few times and everything seems normal.
I have not activated wireless again since my house is wired and I could really do without wireless capability, but eventually I want to know.
My DLink DIR-825 router is still active with both tapes, but using the latest firmware, like the new printer (the other). Is all this took?
Perhaps.
-
79 Service error on Printer series color LaserJet Pro 200 M251
I use this printer with the operating system Mac OSX 10.9.4 for about 9 months.
Now, I get an error message from the Service 79. I tried to turn off the printer and the several times without success.
Curiously, when I try to print a document, a message keeps appearing on my computer that says "the printer has been suspended. You want to resume printing? "When I click on the button resume, nothing prints.
The manual States that the 79 Service error message is related to a firmware issue? Do you know how I can fix this problem?
Thank you very much
Stone
Hi NebraskaPierre,
By your post, I see that you have found a Service 79 error on the printer. I can help you.
Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.
This can be caused by malformed PostScript documents.
Follow these steps:
Locate the power switch on the bottom of the printer.
Turn the printer off position and COUNT to 10.
Turn on the printer and the system should be all together.Try printing from another application to see if you have the same problem.
If a print job from your hand repeatedly causes this error, this may indicate a problem with the print job.Try to split your document upward more before they print it.
Fix permissions of the drive on the Mac: -
Ok. I've seen other messages with this error. But I think mine is a little different.
The problem: Prnter will not print anything at all, even a test page. It will not copy anything either. Low memory - cancelled job message comes up / have worked perfectly for 2 days, and then it started.
Printer is connected via the network (wired), but I have tried wireless also.
Software is installed on a machine windows 10.
In addition to the windows machine, print requests are sent to her through the network via an iPad and an iPhone. HPeprint is also used.
Troubleshooting: I did the following in trying recify problem:
Printer disconnected everything on during 30 seconds.
Reset the default printer
Redid the installation of the network via the touch screen
Deleted printer in windows and deleted driver packages. Reinstalled using the supplied software. Also tried to install using "add a printer" in windows.
Possible corrections that do not go to work or to me:
Put in place as a printer IP - he loses the feature and choose but in addition to the drivers manually to scan etc...
Connect via USB to the computer - if I do this do not lose the ability for the iPad and iPhone to print on the printer - or at least makes this dependant on the computer is turned on and sharing put in place
I will say that after I tried to implement the prnter using "add a printer" in windows, I couldn't get the printer to print the test page - nothing happened, but did not get the memory error message. I removed from the print queue and even deleted all the files in the subdirectory of coils in system32... ButI cannot get rid of the printer now under "devices and printers" in the Panel...
Help, please! Pulling left what my hair on...
Thank you
THIS PROBLEM HAS BEEN RESOLVED.
After several weeks of rtying many different things to fix problems
(1) after installing the new modem Arris double band by carrier Internet, printer would no longer. First issue was an error of memory. After reset printer would no longer at all
(2) I tried installing and uninstalling printer wireless in several ways, ethernet and USB. Printer would never even print a test page. Attempts to print the pages of any other report or configuration would result in the 49 service error
(3) BrightHouse (carrier) was 3 separate times to tweak the modem, try to uninstall and reinstall the printer, etc.
The problem turns out to be that with some modems, HP can not communicate over IPv6 with modem you (they don't play well together using IPv6) either because of the HP or the modem, HP likely due to the fact that he always seems to be HP printers with this problem.
Here are the steps I took finally solved this. Please note that the solution came from a technician BrightHouse to a different Web site. I'm just passing along the info in case it helps others:
(1) completely uninstall the printer from the PC, including the printer, he installed all the software, drivers and all the ports that you may have created trying to recify problems
(2) to shut down the computer
(3) disconnect the ethernet cable from the printer (as applicable)
4) click on the reset button on the home screen to reset to the default values for the printer
(5) do a cold reset the printer (people of email support the HP for the procedure)
(6) on the interface of the printer (screen), go into the settings; network settings, network services. Here you will see IPv4 and IPv6. Disable IPv6. Don't mess wth IPv4 (leave it on).
(7) plug the ethernet cable into the printer or activate/configuration of wireless settings using the printer (screen) interface.
8) turn on the computer
(9) install the printer using the CD that came with it or installation software downloaded from the HP website.
I'm not sure that each of these steps is absolutely necessary, as step 4, but that's what I did...
I saw so many messages on the internet with HP printers not install correctly and launch a 49 service error instead. Not sure how those problems, This applies. But HP needs to fix this issue with their printers IPv6 or at least try to find the cause...
-
M475dw multifunction color HP Laserjet Pro 400 - 49 Service error
I get the error "49 service error" when printing any PDF from adobe acrobat reader document is DC
If I print the same document from the same network share on the same printer using the player of acrober (no), it prints very well. Go figure.
PDF is adobe. First thing would be to update the firmware of the printer or change the PostScript driver from adobe.
-
I get a pcl xl error message when we print our LaserJet Pro 400 Color MFP
When I scan or fax, we get:
PCL XL Error
Subsystem: TEXT
Error: InternalError 0 x 50
File name: cheettext.c
Line number: 710
The printer is a Pro 400 Color MFP LaserJet - m475dw
Windows 7 Professional Service pack 1
What should I do to fix this?
Thanks for the help. I actually did an update of the firmware and it solved the problem.
-
Reference Dell D10S: Software 451dn Laserjet Pro 400 has error during installation.
LaserJet works fine when plugged in to USB, but now moved to a place wireless. The software will not work.
I tried install printer Win 10: "the pilot is not available.
Tried to uninstall the universal printer driver, restart, reinstall the HP driver, error (without code).HP Print doctor can find the device downloads the latest version, but it crashes every time (error, no codes).
Win 10 can see the printer... it is therefore in the range wireless.
I tried all the software different packaging to win 10 on HP site... all get an error during installation.
Here's what worked. I downloaded the universal print driver from HP. These installed to their default location. Taking note of where they have installed.
Then, 10 Windows, try installing the printer laserjet Pro 400. "Missing drivers".<- this="" is="" an="" important="" step.="" leave="" the="" printer="" icon="">->
Then go to control panel, small icons. Device Manager. Search for printers, find the Laserjet printers.
Right-click and choose update drivers. Do not update automatically. Choose the manual option.Look for the universal printer driver. Wait a minute... BOOM. All right. Printing of all wireless PC and laptop.
-
HP Laserjet 2420 printer range: 49.FF05 Service error
Hello
I have a HP Laserjet 2420 printer and it happens with 49.FF05 Service error.
Now I can access some menu items through press and hold down the arrow key and do a reset of the cold etc, now with this work not she also throws the message "Printing work Inprogress". I tried that cancel in the printers menu, and the printer will not install on my PC even with the drivers installed so that I can't use the printer with my PC and try to solve the problem .
So the printer has a pending print job I don't know, also I tried exchanging the DIMM module in other slot and vice versa, but not luck.
Does anyone know how to fix this error without using a PC.
Concerning
Gammyray
It could be anything from a trainer blown just a print job corrupted.
Test: Disconnect the network cable and perform a cold reset. If it's ready, it was probably just a bad impression. Delete everything in the print queues and restart the PC. It should work OK.
But: If it still gives an error 49 with no cable and restart cold, you may have questions that can be more difficult than the unit's worth (depending on how well you expenses of local repair company). You can always buy a trainer on eBay and try to install yourself.
Work around: go to printers remove the printer. If you can find out which IP address has been using the printer, the printer manually program and to use another IP address. Do not re-use that one. Reinstall the printer.
Chances are that someone was trying to print a document based on the web. Files PDF Online is the culprit #1. #2 are weather bulletins. #3's etc, etc, because whatever it is printed from an online source can trigger it.
Make an update of the firmware on the printer. This will help 90% of these questions. Then, inform those who need network print or web documents to save to their hard drive first, close the document online, open the saved document and print from there.
-
HP Laserjet Pro400 M401dn: the 49 Service error
Error 49 Service on screen touch printer. Will print no from a Microsoft Office document.
Have followed the instructions (by HP support) to close printer, unplug the USB and disconnect the power supply to the power surge suppressor and then plug the electrical appliance into the wall socket. Then reconnect USB. All done, rebooted the printer and printed a document internal printer (report Configuration and Menu support) which printed fine.
But printer will not print a document from Microsoft. Of the 49 Service error. Use Microsoft Office v.X student/teacher edition for Mac (2011). It was most recently updated, 10 may 2016 with office update 14.6.4. I printed some documents after this update, but now this 49 daycare error appearing.
Product number for this printer Laserjet Pro400 M401dn is: CF278A
Any help would be appreciated.
Steve945
If you unplug the printer from the computer or network and turn on the fact come ready. If so, then the print job that is still trying to print or a new print job is causing the error. Delete all print jobs from any computer that uses the printer. First upgrade the firmware using the easy firmware updating program. Then try the same job and see if works.
-
On HP Laserjet 3000n 49.4C02 Service error
Our network printer met an over the weekend 49.4c02 service error. The error reads as follows:
49.4C02
The service error of
-------------
Unknown.c
Line = 0
-------------
[PID, TID]
[12.70]
------------
STLVL 0
SRVP.Sl a 0040, 108
------------
STLVL1
SRVP.SL 00409eb8
------------
STLVL2
SRVP.SL 00402f9c
------------
STLVL3
LJ.exe 004013e0
------------
STLVL4
SRVP.SL 00402ea0
-----------
STLVL5
SRVP.SL 00402d6e
----------
STLVL6
Manager called 2ffff000
------------
STLVL7
PageMaker.dll 004ebbe4
------------
STLVL8
PageMaker.dll 004e9124
------------
STLVL9
PageMaker.dll 004ecff8
------------
STLVL10
PageMaker.dll 004e9124
------------
STLVL11
PageMaker.dll 004ece4c
------------
STLVL12
PageMaker.dll 004e9124
------------
STLVL13
PageMaker.dll 004ece4c
------------
STLVL14
PageMaker.dll 004e9124
------------
STLVL15
PageMaker.dll 004ece4c
------------
STLVL16
PageMaker.dll 004e9124
------------
STLVL17
PageMaker.dll 004ece4c
------------
STLVL18
PageMaker.dll 004e9124
------------
STLVL19
PageMaker.dll 004ece4c
------------
STLVL20
PageMaker.dll 004e9124
------------
STLVL21
PageMaker.dll 004ece4c
---------
STLVL22
PageMaker.dll 004e9124
------------
STLVL23
PageMaker.dll 004e9314
------------
STLVL24
PageMaker.dll 004b6fa4
------------
STLVL25
PageMaker.dll 00500af0
------------
STLVL26
PageMaker.dll 004b73c0
------------
STLVL27
PageMaker.dll 004f8658
------------
STLVL28
PageMaker.dll 004a900c
---------
BATTERY END
I tried to disconnect the network diagnostics and printing to the printer and it worked well. Also, I swapped the ethernet cables and uses another port, but as soon as I plug the printer in I get this error and the printer hangs. I can ping the printer's IP, so it seems to be able to communicte with the network very well.
What should I do to fix this?
>... as soon as I plug the printer I get this error...
Do you mean:
- As soon as I plug the printer into a power outlet, or
- As soon as I plug in the printer on the network
If the latter, then it is very likely that something on your network sends a rogue/corrupt print job, which is severely malformed and causing the interpreter of language in the firmware to crash.
-
Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website
LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi
Using IMAC OS 10.8.2 with all updates
Netgear DGN2200v3 router using
Printer not connect to the HP ePrint website
Printer connects using Hp and profile
for fax set up etc. But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh."If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection
ANY IDEAS - HAVE I MISSED SOMETHING?
Thank you very much
I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.
The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.
Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page. Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.
You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.
Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.
Maybe you are looking for
-
Cannot ping PCs within a LAN + results inconsistent telnet
Hello I developed a small application send datagrams via a multicast address. This application also listens 9750 on tcp port. I am testing in a LAN delimited a WRT54G Router with two computers with private addresses (192.168.1.10x). One works on Vist
-
Monitoring selected VM, ESX, cluster hosts
Hello I check if it is possible to select the specified ESX host or Virtual Machines to monitor instead of pulling all the VMS and hosts in Foglight? Thank you. Kind regards Jamie.
-
When I fax from the glass or flat which ever you prefer to call it and I have more than one page, he don't ask me if I'm done or if I have another page, I have to remember to send each page. ?
-
What is the best and most trusted PC "cleaner" out there
My computer windows 7 has acted like a slug, since I had a virus on a few months ago and got rid of him. I have here on the (3ed party and other) programs that will clean the usless files and put an end to unnecessary processes, etc.. Those who make
-
When you try to record images to the picture library, I get the message: "" Windows Internet Explorer: an attempt was made to load a program with an incorrect format. "" I was able to record images before now without any problem. Thank you!