latitude dell max resolution with e-port replicator

Similar Questions

• What is the resolution of the max screen with speed Port Replicator Hi (PA3838E-1PRP)

  Hello

  I have a Toshiba Portege R700 - 11 p and I want to buy a duplicator of Port speed Hi (PA3838E-1PRP), but I want to know the maximum screen resolution with ang VGA HDMI on the port replicator.

  Thanks in advance for your answer

  Hello

  The maximum display resolution depends on the laptop (graphics card) and the external display that is connected to the port replicator to Port Hi-Speed.

  The internal graphics INTEL QM57 (incorporated into the Portégé R700) overview card provides this info:
  http://www.Intel.com/products/Notebook/chipsets/QM57/QM57-overview.htm
  + This chipset supports the DisplayPort interface * with a resolution up to 2560 x 1600. +

  Therefore, check the properties of the external monitor.

• Portege R500: external monitor does not work with the Port Replicator Port 2 and DVI

  I have a Portege R500 running Vista with a slim Port Replicator II and digital monitor Viewsonic.
  I connected the monitor to the DVI port on the port replicator and got it to work OK.
  Press fn + F5 would switch between the computer screen and the external monitor.

  Then it stopped working, and I can't make it work at all. F5 recognizes just the laptop screen.

  If I connect an analog display, it is fine, and I can pass between the two screens without difficulty.

  The strangest thing is that, if I reboot when the Portege R500 is docked, the digital monitor begins by displaying the boot sequence, but then the signal is lost as soon as the screen stops the display of the progress (in low resolution) bar.

  I spent an hour on the phone to support Friday, and he made me nowhere.
  They finished by saying that he should never have worked! So what is the DVI port because then?

  Any ideas?

  David

  Connect your monitor directly to your laptop and see if it is recognized and you can go through FN + F5 between the two views.
  If it works, then connect with port replicator, and then try again.

  It's probably best if you reinstall display drivers. Maybe there are new too on the download page.

• Problems with the port replicator USB 2.0 after installing Windows XP - SP2

  Hello world

  I have a Satellite M30 742 with MS-Windows XP Professional installed. I plugged most of my external devices to him through a port replicator Toshiba USB 2.0. Everything seems to work fine until I installed Service Pack 2.

  Therefore, starting my laptop computer is an adventure to recognize random port replicator: usually four USB ports are recognized, but the ports series and parallel, keyboard and mouse ports are ignored, with a message "unknown USB device".

  Uninstalling and reinstalling, them or their drivers are a vain effort, since Windows keep ignoring them.

  However, in other occasions, they are recognized without problems (even if windows insist on installing their drivers each time that it finds, even if I have already installed a large number of times).

  Please, you have an idea to solve this problem * boring * problem?

  Thank you very much in advance,
  Ricardo.

  Hello

  what you might try is to reinstall the chipset driver because I think that the USB is connected to the chipset.

  In my opinion the Windows upgrade had changed the pilot USB from Toshiba a MS a. So the Port Replicator is not recognized all the time.

  Rudi Bye

• T430 with older port replicator

  Hello.  New to the forum.  About to get my first ThinkPad, a Monday T430

  I come from an older office.  I'm interested in continuing to use the keyboard, mouse, speakers and monitor of this configuration (USB and VGA, nothing complicated) with a sort of host/port replicator docking.  Some of the docks are super expensive (for me, anyway).  I was wondering if anyone has experience with T250410U with a T430 port replicator.  I am not too concerned about the lack of USB 3.0.

  If it does not, it will be possible to have an "extended desktop" if I have the laptop open docked and the external VGA screen attached to the Port Replicator?  Or I would get only released in one of the two?

  Thanks in advance!

  milkmandan wrote:

  I was wondering if anyone has experience with T250410U with a T430 port replicator.

  Welcome to the forums. Unfortunately the 2504 dock will not work because the T430 uses a different physical connector on the bottom of the case.

• audio off when it is associated with the port replicator

  I use Windows XP with my Thinkpad T400 and I bought a Lenovo port replicator model k33415 with my computer.  I have a keyboard and a mouse attached to the Port Replicator port as a PDA sometimes.

  Whenever the port replicator is connected to the computer, the computer speakers do not work and I hear no audio.   When I restart the computer without the attached port replicator, the computer speakers are working fine.      I've tried everything!    Any ideas?

  Hello!  In fact, I fixed it on my own.   Under sound properties I adjusted the audio settings for 'Conexant HD', he made my default device, and under AUdio and then "Advanced", I needed to set speakers to computer speakers.  What I haven't done yet we see if this turns off audio when I unplug the duplicator... so I guess I need to change the default device.   You may not have the same problem, but in any case, good luck!

• Problems with an external monitor with the Port Replicator III and M100

  Hey all.

  I just returned from a trip where I took my laptop. Plugged into the Port Replicator port, started and everything was fine. Then after an hour or two, the monitor stopped receiving a signal. I repositioned the laptop and everything was good again. He then loses signal once again, and I was not able to get a signal via the port replicator since.

  The monitor works fine through the hole at the rear of the M100.

  I checked the pins on the Port Replicator port and portable, none folded and tried to clean any dust etc. Still no signal to the monitor.

  Someone has ideas of how to do to solve this problem?

  Jamo

  Hello

  The Toshiba 3 mobile extension is responsible for the good condition of the duplicator 3 market. Try to reinstall this utility and also check the page of the Toshiba driver for updates.

• Can I use 2 monitors + laptop screen? Latitude E5530 (HD 4000) with E-Port over Docking Station

  Hi Dell Community.

  I for work recently bought a Dell Latitude E5530 with Intel HD Graphics 4000 and an E-Port Plus docking station. Running Windows 7. Currently I have 2 dell monitors that are used with it, but I want to know if it is possible to use my laptop as well screen (3 screens)

  When I try to do it the way regular thanks to display settings it wont let me choose only 2 of the 3.

  I'm wasting my time trying to figure this, or is there a way to do?

  Thanks in advance for any comments

  Ryan

  Unless you install an external video solution non - Intel GPU can lead only two screens at a time.

• Portege R930 - BSOD when connecting monitor high resolution with HDMI port

  Hello.

  I have a Portege R930 (pt331a-01w001) running Windows 7. All about the laptop works as expected, however, when I connect the laptop on a screen high resolution (2560 x 1440) via the HDMI port, I get a blue screen of death.
  Can I use the HDMI port to connect my 1080 p LCD TV and my monitor to work which is a lower resolution and it works well.

  I tried several cables and different monitors of the same resolution.

  If anyone can help?

  Hello

  Simply said: the laptop not breaks down using external monitor with a less than 2560 x 1440 resolution. Right?

  Find your laptop model.
  [Portege R930 PT331A 01W00101 | http://www.mytoshiba.com.au/support/computers/portege/r930/pt331a-01w00101/specifications]

  and it seems that the device supports the Chipset Intel® QM77 Express and Intel® Graphics Media Accelerator QM77

  I recommend updating the graphics card driver.
  You will find the page of the Toshiba Intel display driver v8.15.10.2712 (Win 7)
  Also, you could test the version downloaded from the Intel page.

• U2713HM, max resolution with a laptop without DVI and DisplayPort?

  This is the type of response to a previous post with the same title.  However, the interface of the forum does not seem to allow a response on older posts, even if they remained unanswered and have customers.  Ho-hum. In any case, I discovered that I can drive the U2713HM using a simple HDMI cable to your laptop using the interface of view nVidia Control Panel (page 'Change resolution') property and setting a custom resolution to match the full 2560 x 1440. The trick is to use the Customize button and create a 'custom resolution' for the progressive 32 bits 2560 x 1440, use 'Automatic' and then drop the (Hz) refresh rate up to about 38 to 41 Hz. To find one that works and then keep trying new in 1 Hz increments until it fails. I'm at the wheel of a laptop Toshiba Qosmio, using its output using a refresh of 41 Hz. frequency something higher and display will not 'lock-in' to its native resolution HDMI (available only) the screen (normally connected by Dual link DVI to a desktop machine). So allow me to use the input on the screen switch to switch between my desktop PC and laptop. Works a treat!

  Just thought I would add that:

  This may be possible with a workaround to other problems of option cable - for example, poor quality or cables of big length - where the main problem is one of the supported by the cable or the type of interface bandwidth.  By lowering the refresh rate, you are lowering the bandwidth requirement.  For old CRT screens, it usually resulted in a significant - not so remarkable gradation with LCD/LED technology!  And don't forget that the eye can integrate cini-film at rates as low as 25 Hz!  Affecting the refresh rate of 30 to 48 Hz on a LCD/LED modern is now a viable solution for the problems of bandwidth of cable. Note, however, that all the problems can be addressed by here: for example, I got a cable from DVI single-link for which no stable frequency could be found (the monitor really need Dual - Link DVI - one with a full set of pines).

• Trouble with the port replicator. Use of 2 screens and now only have 1

  Have a new laptop. (Lenovo) also bought duplicator. Hung, everything works fine. Got online to get assistance with updates is not crowned success, after that I just use of screen on laptop, any other monitor disappeared. Can't get it back

  Hi Tom,

   

  Thanks for posting the question in the Microsoft Community!

   

  You are unable to get the display of multiple monitors.

   

  I suggest you to contact Lenovo to get help for this issue.

   

  You can try to get help on the site:

  http://support.Lenovo.com/en_US/feedback/contactsupport.page

   

  If you need any other assistance, let us know and we would be happy to help you.

   

   

   

   

• Driver Toshiba Hi speed Port Replicator III

  Hello.

  I can't find a driver for Toshiba Hi speed Port Replicator III driver on your driver page.

  These need drivers or they are plug-and-play? The port replicator USB ports do not work.

  Thank you.

  I'm not 100% sure but I think you should be able to use all phones compatible with this port replicator.
  What model of laptop do you have?
  Do you use it with the original OS that you got with it?

• No audio output speakers Z50 - A Port Replicator PA5116A - PRI or Tecra

  I just got a new Tecra Z50A Toshiba with a port replicator Port-PRI PA5116A, when I first put it in the doc, he began to load the drivers.
  But during this process, the connection to the local network of abandonment and an error came stating that only four of the eight drivers have been installed.

  Now, the problem I have is that no sound / music out laptop speakers when in the RFSO or replicators offline to the speakers.
  I checked the playback settings that seem to be corrected.
  No mute setting.

  Any suggestions?

  I just got a new Tecra Z50A Toshiba with a PA5116A-PRI port replicator, when I first put it in the doc, he began to load the drivers.
  But during this process, the connection to the local network of abandonment and an error came showing that only four of the eight drivers have been installed.

  Now, the problem I have is that no sound / music out laptop speakers when in the RFSO or replicators offline to the speakers.
  I checked the playback settings that seem to be corrected.

  No mute setting.

  Any suggestions?

  Hello

  you have tested an update of the audio driver and install displaylink?

• Portege R500 - configure the parser on the Port Replicator

  The system is Portege R500 with a port replicator Port MS Vista running. Port replicator has a Philips 19 "LCD monitor

  System has BEEN configured so that when the system was in the duplicator monitor 19 "inches would be active and system monitor is inactive.

  But, a few days before the following events occur, when the system is in the port replicator and its turned on screen (the one with the mobile progress indicator) Windows startup is displayed on the Port Replicator monitor, then the screen turns white and displays them on the screen on the monitor system, after entering the desktop on the monitor system.

  I live in a remote area, so I can't pop in the store of the local computer to ask for help.

  I would appreciate someone to give me some guidance as to where it configures the port replicator monitor configuration. I looked at the section Configuration screen Control Panel but it seems to be the performance of two monitors, it appears not to address the peculiarities of a laptop computer with a port replicator configuration

  Thank you

  Hello

  I have no Portege R500 but I ve used external monitor connected to my Tecra duplicator.
  Can you please tell me how you have configured previously?

  What is your external monitor set as primary monitor?

• Tecra A11 Port Replicator - do not enable external HARD disk when securing

  Hello

  Had a problem with the Port Replicator port for my new Tecra - A11.

  When I anchor the laptop in the Replicator, that is not automatically connecting external 700gig USB backup HDD, I have either pull the USB cable on the Replicator, or disable the drive HARD and again so he can be seen and recognized.

  I never had this problem with my A8 and its replicator, I could just dock and everything was fine.

  I am running Win7

  Thank you... PK

  Hello

  Seems that Win 7 is unable to recognize the external HARD drive that is already connected to the port replicator.
  I m not very good if you had to install a software for this external HARD drive, but if software is required, and then try to reinstall again.